Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Heavy ion irradiation effects on CrFeMnNi and AlCrFeMnNi high entropy alloys

Co-free but Al-included medium/high entropy alloys (M/HEAs) have gained increasing interests due to their lower cost and the potential to tune the multi-phase microstructure. The irradiation response of two Co-free HEAs, face-centered cubic (FCC) CrFeMnNi with limited Cr enriched α' phase and body-centered cubic (BCC) AlCrFeMnNi with B2s phase and nanoprecipitates were explored. Ion irradiations using 5 MeV Fe 2+ ions were performed at 500°C to a peak fluence of 50 and/or 100 displacements per atom (dpa). In dual-phase AlCrFeMnNi, there was no significant radiation induced segregation or chemical intermixing at the coherent matrix (FeCrMn-rich)/second phase (AlNi-rich) boundaries. In CrFeMnNi, limited voids were only detected at the peak damage location of ~ 50 dpa. On the other hand, voids were widely distributed in AlCrFeMnNi: under 50 and 100 dpa irradiation conditions, voids were found with larger dimension and denser distribution in the FeCrMn-rich matrix, smaller and slightly lower density in an AlNi-rich second phase. In addition, the diameter of the FeCMn-rich nanoprecipitates didn't reveal any tendency of dissolution or growth. This is correlated with their superior structural stability against irradiation. Significant radiation-induced hardening (increases from 3.8 ± 0.2 GPa to 4.7 ± 0.6 GPa) was measured in CrFeMnNi, but only ~ 4% hardness increase (from 7.4 ± 0.8 GPa to 7.7 ± 0.4 GPa) was noted in AlCrFeMnNi. Finally, in addition to the radiation-induced defects, such as voids, dislocation loops and point defects, other factors, such as chemical short-range ordering may play an important role.

36 MATERIALS SCIENCE↗

Molecular dynamics studies of defect formation during heteroepitaxial growth of InGaN alloys on (0001) GaN surfaces

Here, we investigate the formation of extended defects during molecular-dynamics (MD) simulations of GaN and InGaN growth on (0001) and (11$\bar{2}$0) wurtzite-GaN surfaces. The simulated growths are conducted on an atypically large scale by sequentially injecting nearly a million individual vapor-phase atoms towards a fixed GaN surface; we apply time-and-position-dependent boundary constraints that vary the ensemble treatments of the vapor-phase, the near-surface solid-phase, and the bulk-like regions of the growing layer. The simulations employ newly optimized Stillinger-Weber In-Ga-N-system potentials, wherein multiple binary and ternary structures are included in the underlying density-functional-theory training sets, allowing improved treatment of In-Ga-related atomic interactions. To examine the effect of growth conditions, we study a matrix of >30 different MD-growth simulations for a range of InxGa1-xN-alloy compositions (0 ≤ x ≤ 0.4) and homologous growth temperatures [0.50 ≤ T/T* m (x) ≤ 0.90], where T* m (x) is the simulated melting point. Growths conducted on polar (0001) GaN substrates exhibit the formation of various extended defects including stacking faults/polymorphism, associated domain boundaries, surface roughness, dislocations, and voids. In contrast, selected growths conducted on semi-polar (11$\bar{2}$0) GaN, where the wurtzite-phase stacking sequence is revealed at the surface, exhibit the formation of far fewer stacking faults. We discuss variations in the defect formation with the MD growth conditions, and we compare the resulting simulated films to existing experimental observations in InGaN/GaN. Finally, while the palette of defects observed by MD closely resembles those observed in the past experiments, further work is needed to achieve truly predictive large-scale simulations of InGaN/GaN crystal growth using MD methodologies.

74 ATOMIC AND MOLECULAR PHYSICS↗

Acoustic Emission Responses of Three Typical Metals During Plastic and Creep Deformations

In this paper, the acoustic emission (AE) responses of three typical engineering metals (namely, Q235 carbon steel, H62 brass and 304 stainless steel) during plastic and high-temperature creep deformations were experimentally investigated. To gain insight into the AE response mechanisms, the micro scale mechanical behaviors of these metals were studied with a micro-tensile tester with observation by scanning electron microscopy (SEM). The following observations were found: (1) although the intensities and activities of the AE signals greatly differed under the same configurations, the AE peak values appeared at the transition from elasticity to plasticity for all three metals; (2) compared to the AE signal intensity during plastic deformation, the signal intensity during high-temperature creep was much weaker; (3) slip lines appeared within the crystal grains at the stress level corresponding to the peak AE signal intensity, but the densities of the slip lines and their crossover were not proportional to the AE signals of the metals. From these findings, the following conclusions were drawn about the application of AE: (1) AE is more scientific method to determine the yielding point of a metal without plastic flow than the nominal yield stress; (2) AE can be used to determine the deformation mechanism at high temperature, particularly, to distinguish creep from plastic deformation; (3) the AE response is the result of a sudden energy release by dislocation motion; however, the AE signal intensity is not necessarily proportional to the dislocation activity.

36 MATERIALS SCIENCE↗

Modes of strain accommodation in Cu-Nb multilayered thin film on indentation and cyclic shear

Two-phase layered thin films with a high density of semi-coherent interfaces exhibit excellent mechanical properties and thermal stability. Here, in this study, a magnetron-sputtered Cu-Nb dual-layered thin film (~500 nm for Cu and ~150 nm for Nb) having an amorphous interface between Cu and Nb with a high density of aligned growth twins in Cu is subjected to severe surface deformation. The material is loaded using indentation and cyclic shear under tribological testing. The strain accommodation in the subsurface microstructure after deformation varies based on the local structure and deformation mode. Grain refinement and crack formations in the stressed region of the Nb layer and localized crystallization of the amorphous interface are observed after indentation and scratch testing. Pronounced detwinning of growth twins in the Cu layer under the cyclic shear strain leaves large dislocations sites and loops which are observed both by high-resolution transmission electron microscopy and experiment-guided molecular dynamic (MD) simulations. Our simulations provided insights into understanding the pathway for the detwinning process under cyclic shear loading.

36 MATERIALS SCIENCE↗

Complexions at the iron-magnetite interface

Synthesizing distinct phases and controlling crystalline defects are key concepts in materials design. These approaches are often decoupled, with the former grounded in equilibrium thermodynamics and the latter in nonequilibrium kinetics. By unifying them through defect phase diagrams, we can apply phase equilibrium models to thermodynamically evaluate defects—including dislocations, grain boundaries, and phase boundaries—establishing a theoretical framework linking material imperfections to properties. Using scanning transmission electron microscopy (STEM) with differential phase contrast (DPC) imaging, we achieve the simultaneous imaging of heavy Fe and light O atoms, precisely mapping the atomic structure and chemical composition at the iron-magnetite (Fe/Fe 3 O 4 ) interface. We identify a well-ordered two-layer interface-stabilized phase state (referred to as complexion) at the Fe[001]/Fe 3 O 4 [001] interface. Using density-functional theory (DFT), we explain the observed complexion and map out various interface-stabilized phases as a function of the O chemical potential. The formation of complexions increases interface adhesion by 20% and alters charge transfer between adjacent materials, impacting transport properties. Our findings highlight the potential of tunable defect-stabilized phase states as a degree of freedom in materials design, enabling optimized corrosion protection, catalysis, and redox-driven phase transitions, with applications in materials sustainability, efficient energy conversion, and green steel production.

36 MATERIALS SCIENCE↗

Preferred Orientation of Quartz in Metamorphic Rocks from the Bergell Alps

Crystal preferred orientation of 47 samples of quartzite and eight samples of associated marbles from the Bergell Alps have been analyzed with time-of-flight neutron diffraction and EBSD. The results show a clear distinction of texture types for quartzites transformed from Triassic sandstones and quartz layers in gneiss. Textures of Triassic quartzites are overall weak and display a maximum of c-axes perpendicular to the foliation or a crossed girdle perpendicular to the lineation. Pole figures for positive rhombs {10 1 ¯ 1} show a maximum perpendicular to the foliation and negative rhombs {01 1 ¯ 1} generally display a minimum. Based on polycrystal plasticity models this texture type can be attributed to a combination of basal and rhombohedral slip. Asymmetry of the distributions is attributed to simple shear and local strain heterogeneities. The relatively weak texture is partially caused by muscovite limiting dislocation motion and grain growth, as well as adjacent layers of marble that accommodate significant strain. Most quartz layers in gneiss, including mylonites, display a texture with a-axes parallel to the lineation and a c-axis maximum in the intermediate fabric direction. This texture type can be attributed to dominant prismatic slip. Many samples are recrystallized and recrystallization appears to strengthen the deformation texture. The study shows good agreement of neutron diffraction and EBSD. Neutron diffraction data average over larger volumes and maximum pole densities are generally lower and more representative for the bulk material. With EBSD the microstructure and mechanical twinning can be quantified.

54 ENVIRONMENTAL SCIENCES↗

Atomistic Simulations of Mass and Thermal Transport in Oxide Nuclear Fuels

In this talk we discuss simulations of the mass and thermal transport in oxide nuclear fuels. Redistribution of fission gases such as Xe is closely coupled to nuclear fuel performance. Most fission gases have low solubility in the fuel matrix, specifically the insolubility is most pronounced for large fission gas atoms such as Xe, and as a result there is a significant driving force for segregation of gas atoms to grain boundaries or dislocations and subsequently for nucleation of gas bubbles at these sinks. The first step of the fission gas redistribution is diffusion of individual gas atoms through the fuel matrix to existing sinks, which is governed by the activation energy for bulk diffusion. Fission gas bubbles are then formed by either separate nucleation events or by filling voids that were nucleated at a prior stage; in both cases their formation and latter growth is coupled to vacancy dynamics and thus linked to the production of vacancies via irradiation or thermal events. In order to better understand bulk Xe behavior (diffusion mechanisms) in UO 2±x we first calculate the relevant activation energies using density functional theory (DFT) techniques. By analyzing a combination of Xe solution thermodynamics, migration barriers and the interaction of dissolved Xe atoms with U, we demonstrate that Xe diffusion predominantly occurs via a vacancy-mediated mechanism, though other alternatives may exist in high irradiation fields. Since Xe transport is closely related to diffusion of U vacancies, we have also studied the activation energy for this process. In order to explain the low value of 2.4 eV found for U migration from independent damage experiments (not thermal equilibrium) the presence of vacancy clusters must be included in the analysis. Next a continuum transport model for Xe and U is formulated based on the diffusion mechanisms established from DFT. After combining this model with descriptions of the interaction between Xe and grain boundaries derived from separate atomistic calculations, we simulate Xe redistribution for a few simple microstructures using finite element methods (FEM), as implemented in the MOOSE framework from Idaho National Laboratory. Thermal transport together with the power distribution determines the temperature distribution in the fuel rod and it is thus one of the most influential properties on nuclear fuel performance. The fuel thermal conductivity changes as function of time due to microstructure evolution (e.g. fission gas redistribution) and compositional changes. Using molecular dynamics simulations we have studied the impact of different types of grain boundaries and fission gas bubbles on UO 2 thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Response of 14YWT alloys under neutron irradiation: A complementary study on microstructure and mechanical properties

Nanostructured ferritic alloys (NFAs) having sub-micron grain size with a high density of nano-oxides (NOs) (size of ~2-3 nm) are one of the best candidates for structural components in Generation IV nuclear systems. In this study, 14YWT NFA cladding tubes were irradiated in BOR60 reactor up to 7 dpa at 360-370 °C. Detailed microstructural analysis has been conducted using bright field transmission electron microscopy, bright field scanning transmission electron microscopy, energy filtered transmission electron microscopy, energy dispersive X-ray spectroscopy, electron energy loss spectroscopy and transmission Kikuchi diffraction techniques. This revealed cavities, <100> and <111> type dislocation loops, and α' precipitates forming after irradiation with relationships between cavities and NOs, and α' precipitates and NOs. Cavities mostly form on the NOs; whereas, α' precipitates form between the NOs where the point defect concentration is high. Moreover, α' precipitates are distributed homogenously on and around the dislocation loops which is consistent with the observation that there is no Cr segregation on dislocation loops. Grain boundaries were found to be mostly depleted in Cr; however, the characteristics of each grain boundary determines the Cr behavior and the α' denuded zone around the grain boundaries. Mechanical properties of the irradiated tubes have been determined by using both low force and high force nanoindentation techniques, resulting in 1.03±0.33 GPa and 0.82±0.20 GPa hardening, respectively. Dispersed barrier hardening calculations and nanoindentation measurements are in good agreement. In this paper, 14YWT NFA has been systematically studied after neutron irradiation to better understand its superior performance: low α' concentration, low swelling and low radiation-induced hardening.

36 MATERIALS SCIENCE↗

In situ study on the compression deformation of MoNbTaVW high-entropy alloy

The excellent mechanical properties of high-entropy alloys (HEAs) make them promising materials for advances in science and technology. However, the underlying mechanism of plastic deformation is not well understood. In situ experiments are urgently required to provide a fundamental understanding of the plastic deformation under high pressure. We performed in situ synchrotron X-ray diffraction (XRD) experiments to study compression deformation behavior of the HEA MoNbTaVW in a radial diamond anvil cell (rDAC). Our results show that the strength and ratio of the stress-to-shear modulus values are ~1.5 and 3 times that of pure tungsten (W), respectively. MoNbTaVW showed plastic deformation above 5 GPa and displayed a much stronger texture. In this work, we found that the active dislocation behavior is mainly responsible for the high strength in MoNbTaVW under compression. This unique technique opens a new avenue to investigate the in situ mechanical properties and their mechanism in other types of HEAs.

36 MATERIALS SCIENCE↗

Longitudinal position dependence of dark line defect growth rate in high-power diode lasers at 790 nm

Using a nondestructive, in situ near-infrared defect imaging technique, we obtained time-resolved images of dark line defect (DLD) growth in the cavities of several high-power 790-nm diode lasers and calculated individual DLD growth rates. A clear longitudinal spatial dependence in the DLD growth rate was observed, in which the DLD growth rate was faster near the anti-reflective (AR) facet. Longitudinal spatial hole burning simulation results indicate that the total photon density increases toward the AR facet, while the carrier density decreases toward the AR facet. Here, these results suggest that photon absorption plays a key role in enhancing DLD growth beyond the contribution of the traditional carrier capture mechanism. Asymmetric DLD growth that was preferentially directed toward the high-reflectivity facet was also observed, providing further support for the role of photon absorption in the growth process. To account for these findings, we propose a photon-accelerated mechanism for the enhancement of DLD growth in which the slower carrier capture process in the traditional recombination-enhanced dislocation glide mechanism is replaced by a faster photon absorption process.

Engineering - Electronic and electrical engineerin↗

Tellurium Secondary-Phase Defects in CdZnTe and their Association With the 1.1-eV Deep Trap

Defects located at the EC - 1.1 (eV) level, which are electro-optically active deep traps, generally have been overlooked since their presence cannot be detected except for those in highly resistive CdTe compounds. The origin of this trap is still debated on whether it is from Te vacancies or from dislocations induced by secondary phase defects in Te. We have grown high-resistivity Te-rich CZT ingots to clarify the origin of the 1.1 eV defects and to analyze the defect levels in the CZT samples by current deep level transient spectroscopy (I-DLTS)and photoluminescence (PL). From the analysis, defect levels such as shallow acceptor/donor, A-centers, Cd vacancies and Te antisite appeared to be in both high and low concentrations of Te inclusions, but the level of 1.1-eV defects exhibited dependence on the density of Te inclusion in the CZT samples. We also evaluated the effect of the 1.1-eV deep-level defects on the detector's performance in point view of carrier trapping and de-trapping.

36 MATERIALS SCIENCE↗

Electric-field-assisted-sintering of rare-earth oxide dispersion strengthened Fe-Cr-Mo alloys

Oxide dispersion-strengthened (ODS) alloys are widely recognized for their exceptional high-temperature strength, creep resistance, and radiation tolerance, making them indispensable for advanced nuclear reactors, aerospace, and energy systems. Achieving a fine and stable dispersion of oxide nanoparticles is critical, as these particles act as strong barriers to dislocation motion and effective sinks for irradiation-induced defects, ensuring structural integrity under extreme conditions. Here, in this study, Fe–Cr–Mo-based ODS alloys were fabricated via mechanical alloying and consolidated using electric-field-assisted sintering (EFAS) with additions of Y 2 O 3 , La 2 O 3 , and CeO 2 . EFAS processing produced ultrafine-grained microstructures (average grain size <1 μm) with uniformly distributed oxide clusters (2–4 nm). Atom probe tomography revealed that La 2 O 3 -containing alloys exhibited the highest nanoparticle number density, resulting in superior tensile strength compared to yttria- and ceria-bearing counterparts. The combined effect of grain refinement and rare-earth oxide dispersion significantly enhanced mechanical performance, demonstrating the potential of EFAS for developing high-strength ferritic alloys for demanding environments such as nuclear systems.

36 - MATERIALS SCIENCE↗

A nanoscale co-precipitation approach for property enhancement of Fe-base alloys

Precipitate size and number density are two key factors for tailoring the mechanical behavior of nanoscale precipitate-hardened alloys. However, during thermal aging, the precipitate size and number density change, leading to either poor strength or high strength but significantly reduced ductility. Here we demonstrate, by producing nanoscale co-precipitates in composition-optimized multicomponent precipitation-hardened alloys, a unique approach to improve the stability of the alloy against thermal aging and hence the mechanical properties. Our study provides compelling experimental evidence that these nanoscale co-precipitates consist of a Cu-enriched bcc core partially encased by a B2-ordered Ni(Mn, Al) phase. This co-precipitate provides a more complex obstacle for dislocation movement due to atomic ordering together with interphases, resulting in a high yield strength alloy without sacrificing alloy ductility.

36 MATERIALS SCIENCE↗

Ramp compression of tantalum to 330 GPa

We report on the stress–density and rate-dependent response for Ta, ramp compressed to 330 Pa with strain rates up to 5 x 108 s -1 . We employ temporally shaped laser drives to compress Ta stepped foils over several to tens of nanoseconds. Lagrangian wave-profile analysis reveals a stress–density relationship which falls below the Hugoniot, above the hydrostat, and is consistent with ramp-compression experiments at lower strain rates. We also report on the peak elastic stress prior to plastic deformation as a function of strain rate for laser-driven ramp and shock-compression data spanning the 1–50 × 107 s -1 strain-rate range. When combined with previously published lower strain data (101–107 s -1 ), we observe a change in rate dependence, suggesting a transition from thermally activated to defect-limited (phonon drag) dislocation motion occurring at a strain rate of about 105 s -1 .

36 MATERIALS SCIENCE↗

Dose dependence of helium bubble formation in nano-engineered SiC at 700 °C

Knowledge of radiation-induced helium bubble nucleation and growth in SiC is essential for applications in fusion and fission environments. Here we report the evolution of microstructure in nano-engineered (NE) 3C SiC, pre-implanted with helium, under heavy ion irradiation at 700 °C up to doses of 30 displacements per atom (dpa). Elastic recoil detection analysis confirms that the as-implanted helium depth profile does not change under irradiation to 30 dpa at 700 °C. While the helium bubble size distribution becomes narrower with increasing dose, the average size of bubbles remains unchanged and the density of bubbles increases somewhat with dose. These results are consistent with a long helium bubble incubation process under continued irradiation at 700 °C up to 30 dpa, similar to that reported under dual and triple beam irradiation at much higher temperatures. The formation of bubbles at this low temperature is enhanced by the nano-layered stacking fault structure in the NE SiC, which enhances point defect mobility parallel to the stacking faults. Here, this stacking fault structure is stable at 700 °C up to 30 dpa and suppresses the formation of dislocation loops normally observed under these irradiation conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Role of Selenium Addition to CdZnTe Matrix for Room-Temperature Radiation Detector Applications

Because of its ideal band gap, high density and high electron mobility-lifetime product, cadmium zinc telluride (CdZnTe or CZT) is currently the best room-temperature compound-semiconductor X- and gamma-ray detector material. However, because of its innate poor thermo-physical properties and above unity segregation coefficient for Zn, the wide spread deployment of this material in large-volume CZT detectors is still limited by the high production cost. The underlying reason for the low yield of high-quality material is that CZT suffers from three major detrimental defects: compositional inhomogeneity, high concentrations of dislocation walls/sub-grain boundary networks and high concentrations of Te inclusions/precipitates. To mitigate all these disadvantages, we report for the first time the effects of the addition of selenium to the CZT matrix. The addition of Se was found to be very effective in arresting the formation of sub-grain boundaries and its networks, significantly reducing Zn segregation, improving compositional homogeneity and resulting in much lower concentrations of Te inclusions/precipitates. Growth of the new quaternary crystal Cd 1-x Zn x Te 1-y Se y (CZTS) by the Traveling Heater Method (THM) is reported in this paper. We have demonstrated the production of much higher yield according to its compositional homogeneity, with substantially lower sub-grain boundaries and their network, and a lower concentration of Te inclusions/precipitates.

36 MATERIALS SCIENCE↗

Grand canonically optimized grain boundary phases in hexagonal close-packed titanium

Grain boundaries (GBs) profoundly influence the properties and performance of materials, emphasizing the importance of understanding the GB structure and phase behavior. As recent computational studies have demonstrated the existence of multiple GB phases associated with varying the atomic density at the interface, we introduce a validated, open-source GRand canonical Interface Predictor (GRIP) tool that automates high-throughput, grand canonical optimization of GB structures. While previous studies of GB phases have almost exclusively focused on cubic systems, we demonstrate the utility of GRIP in an application to hexagonal close-packed titanium. We perform a systematic high-throughput exploration of tilt GBs in titanium and discover previously unreported structures and phase transitions. In low-angle boundaries, we demonstrate a coupling between point defect absorption and the change in the GB dislocation network topology due to GB phase transformations, which has important implications for the accommodation of radiation-induced defects.

36 MATERIALS SCIENCE↗