Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Structural and morphological properties of sputtered NiO thin films at various sputtering pressures

Nickel oxide thin films were successfully deposited on glass substrates at different sputtering pressures in the range of 3 x 10{sup -2} to 5 x 10{sup -2} mbar. It was observed that sputtering pressure influenced the structural and morphological properties. Structural properties were studied with X-ray diffractometer. All the deposited films were polycrystalline and exhibited cubic structure with preferential growth along (220) plane. From morphological studies it was observed that fine and uniform grains with RMS roughness of 9.4 nm were obtained when the films deposited at a sputtering pressure of 4 x 10{sup -2} mbar,. The grain size and the surface roughness decreased at higher sputtering pressures. The surface mobility of the adatoms decreased after series of collisions resulting in the decrease of grain size at high sputtering pressures.

36 MATERIALS SCIENCE↗

Three dimensional numerical scattering from ocean-like surfaces

A new method of calculating the electric field scattered from two-dimensional conducting rough surfaces is presented. This method uses the operator conjugate gradients technique and the extended boundary condition equation. This avoids the build-up of round-off errors encountered in the inversion of large matrices. It also avoids the singularities of the integral kernels usually encountered in the method of moments. Techniques for improving the rate of convergence by applying physical constraints are discussed. This method is presently being used to calculate the polarization signatures from simulated ocean-like surfaces.

Rodriguez, Ernesto↗

ESM Roughness Datasets (ARC)

This work focused on the effects on turbulent heat transfer due to surface roughness of types relevant to NASA entry missions, and was supported by NASA’s Entry Systems Modeling (ESM) Project. The emphasis was on new classes of woven materials, which are enabling for many missions.

heat transfer↗

Direct photoetching of polymers using radiation of high energy density from a table-top extreme ultraviolet plasma source

In order to perform material interaction studies with intense extreme ultraviolet (EUV) radiation, a Schwarzschild mirror objective coated with Mo/Si multilayers was adapted to a compact laser-driven EUV plasma source utilizing a solid Au target. By 10x demagnified imaging of the plasma a maximum pulse energy density of {approx}0.73 J/cm{sup 2} at a wavelength of 13.5 nm can be achieved in the image plane of the objective at a pulse duration of 8.8 ns. In this paper we present EUV photoetching rates measured for polymethyl methacrylate, polycarbonate, and polytetrafluoroethylene at various fluence levels. A linear dependence between etch depth and applied EUV pulse number could be observed without the necessity for any incubation pulses. By evaluating the slope of these data, etch rates were determined, revealing also a linear behavior for low fluences. A threshold energy density could not be observed. The slope of the linear etch regime as well as deviations from the linear trend at higher energy densities are discussed and compared to data known from deep UV laser ablation. Furthermore, the surface roughness of the structured polymers was measured by atomic force microscopy and compared to the nonirradiated polymer surface, indicating a rather smooth etch process (roughness increase of 20%-30%). The different shapes of the etch craters observed for the three polymers at high energy densities can be explained by the measured fluence dependence of the etch rates, having consequences for the proper use of polymer ablation for beam profiling of focused EUV radiation.

36 MATERIALS SCIENCE↗

Roughness of Cylindrical Parts in Transverse Burnishing by Flat Plates

The use of transverse burnishing by means of flat plates for combined finishing and strengthening of cylindrical parts is considered. The influence of the compressive strain and the total number of workpiece rotations on the surface roughness is determined experimentally.

42 ENGINEERING↗

Evaluation of transfer films of Salox M on 440C for HPOTP bearing cage applications, task 119

The objective of the task was to evaluate the suitability of a bronze-filled polytetra fluoroethylene (Salox M) as the cage material in Space Shuttle Main Engine (SSME) high pressure oxygen turbo pump (HPOTP) bearings. The role of the cage pocket material will be to provide a transferred lubricating interface at the ball-race contact region. A series of experiments was conducted which involved block-on-ring tests (the block was the polytetrafluoroethylene (PTFE) -filled material and the ring was through-hardened 440C steel) and high speed traction tests of two 440C disks with one disk rubbed with a PTFE block to generate a transfer film. Measurements included post test visual observations of the condition of the 440C, wear rate measurements of the blocks, and traction measurements between the disks. It was observed that both Salox M and glass-filled PTFE (Armalon) transferred PTFE to 440C at cryogenic temperatures. Bronze is also transferred to uncoated 440C from the Salox M. At room temperature no PTFE transfer was observed in the high speed disk tests due to severe frictional heating, although bronze transfer still occurred with the bronze-PTFE Salox M material. Since the bearing will operate at cryogenic temperature, transfer films are very probable. Salox M wore slightly, although probably tolerably, more than glass-filled PTFE against 440C. However, Salox M is clearly less abrasive to 440C than is the glass-filled material. When the surface layer of PTFE is depleted from the glass-filled material, the glass fibers tend to seriously abrade the steel. This problem does not occur with Salox M. The surface roughness studies indicate that smooth balls are quite reasonable for transfer films. No significant difference in wear rates of the candidate cage materials was observed when the 440C surface finish was increased from 0.025 micron to 0.1 micron cla. At higher levels of roughness, the wear rate increased. Two surface coatings (MoS2 and TiN) were tested. The surface coatings tended to reduce the Salox M wear rate and reduce bronze transfer. PTFE transfer at cryogenic temperatures still occurred with the surface coatings. Two cage design concepts are presented utilizing Salox M material. One design involves a metal-reinforced Salox M cage, while the second design uses Salox M inserts in a metal structure.

Barber, S. A.↗

Precise Fabrication of Silicon Wafers Using Gas Cluster Ion Beams

Precise surface processing of a silicon wafer was studied by using a gas cluster ion beam (GCIB). The damage caused to the silicon surface was strongly dependent on irradiation parameters. The extent of damage varied with the species of source gas and the acceleration voltage (Va) of cluster ions. It also varied with the cluster size and residual gas pressure. The influence of electron acceleration voltage (Ve) used for ionization of a neutral cluster was also investigated. The irradiation damage, such as an amorphous silicon (a-Si) layer, a mixed layer of a-Si and c-Si (transition layer), and surface roughness, was increased with Ve. It is suggested that the increase in the amount of energy per atom was induced by high Ve, because of variation of the cluster size and/or cluster charge. An undamaged smooth surface can be produced by Ar-GCIB irradiation at low Ve and Va.

36 MATERIALS SCIENCE↗

Distribution of germanium in Si{sub 1-x}Ge{sub x} (x < 0.1) layers grown on the Si(001) substrate as a function of layer thickness

The germanium distribution in Si(001)/Si{sub 1-x}Ge{sub x} layers as a function of the layer thickness at a low dopant concentration (x < 6%) has been investigated using high-resolution X-ray diffractometry and low-temperature photoluminescence. It has been shown that the germanium concentration increases with increasing thickness of the SiGe layer with the formation of lateral inhomogeneities at the boundary between this layer and a silicon cap layer for a layer thickness of 30 nm or more. These inhomogeneities have an oriented character and give rise to anisotropic diffuse scattering for the system of (113) and (224) asymmetric reflections from SiGe. The luminescence of these films at low temperatures and low excitation densities is an emission of localized and delocalized excitons, which is characteristic of systems with disorder. The revealed nonuniform germanium distribution in the lateral direction is associated with the accumulation of germanium in the near-surface SiGe layer and with the partial relaxation of elastic strains due to the development of surface roughness and the preferred incorporation of germanium atoms into one side of the surface ripples.

36 MATERIALS SCIENCE↗

Uncooled GeSn MWIR Photodetectors Using Fully Relaxed Thin Triple‐Step Buffer

GeSn photodetectors monolithically grown on Ge virtual substrates demonstrate mid-wave infrared (MWIR) detection at room temperature. The lattice mismatch between GeSn and Ge causes dislocations and compressive strain, creating leakage pathways and unwanted indirect band transitions. Designed thin Ge 0.91 Sn 0.09 triple-step buffer layers of ≈175 nm total thickness reduce dislocations and enable full relaxation, showing 100% lattice relaxation and smooth surface roughness of 0.83 nm with shorter auto-correlation length in surface morphology compared to single-step buffers. Ge 1-x Sn x photodetectors (x = 0.09, 0.12, and 0.15) on triple-step buffers with n-i-p configurations achieve lattice strain relaxations of 99%, 88%, and 80%, respectively. Ge 0.91 Sn 0.09 and Ge 0.88 Sn 0.12 show gradual variation in auto-correlation amplitude, while Ge 0.85 Sn 0.15 shows an increase due to lattice mismatch. Shockley–Read–Hall recombination current dominates at low reverse bias due to mismatch-induced dislocations, while band-to-band tunneling current dominates at higher reverse bias due to narrowing bandgap under strong electric fields. Here, the photodetectors show extended spectral response with increasing Sn composition of i-GeSn active layer sandwiched by barriers. Ge 0.88 Sn 0.12 and Ge 0.85 Sn 0.15 exhibit extended wavelength cut-offs of 3.12 and 3.27 µm at room temperature, demonstrating significant potential for silicon-based MWIR applications.

GeSn↗

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗

Small-Angle X-ray Scattering Study of Protein Complexes with Tea Polyphenols

Exploration of the structure of protein complexes, especially the change in conformation and aggregation behavior of proteins upon ligand binding, is crucial to clarify their bioactivities at the molecular level. We applied solution small-angle X-ray scattering (SAXS) to study the complex structure of bovine serum albumin (BSA) and trypsin binding with tea polyphenols, that is, catechin and epigallocatechin gallate (EGCG). We found that tea polyphenols can steadily promote the aggregation of proteins and protein complexes through their bridging effect. The numbers of proteins in the complexes and in the aggregates of complexes are extracted from SAXS intensity profiles, and their dependences as a function of the molar ratio of polyphenol to protein are discussed. EGCG has stronger capability than catechin to promote complex formation and further aggregation, and the aggregates of complexes have a denser core with a relatively smooth surface. The aggregates induced by catechin are loosely packed with a rough surface. BSA shows higher stability than trypsin in the formation of complex with a well-folded conformation. The synergistic unfolding of trypsin results in larger aggregates in the mixtures with more tea polyphenols. The binding affinity and number of tea polyphenols bound to each protein are further determined using fluorescence spectroscopy. Furthermore, the structure of protein complexes explored in this work is referable in the preparation of protein complex-based particles and the understanding of polyphenol-induced formation and further aggregation of protein complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of thermal transport degradation in rough Si nanowires

Thermal transport through $\langle$100$\rangle$ and $\langle$110$\rangle$ rough Si nanowires is explored using an atomistic quantum transport approach based on a modified Keating model and the wave function formalism. The thermal conductance, resistance, and conductivity are calculated for different nanowire lengths and the root mean square of the rough surfaces. The simulation results reflect that thermal transport is diffusive in rough nanowires without surrounding oxide layers. Its degradation, as compared to ideal structures, cannot be attributed to phonon localization effects, but to the properties of the phonon band structure. Phonon bands with an almost flat dispersion cannot propagate through disordered structures because of the mode mismatch between adjacent unit cells.

36 MATERIALS SCIENCE↗

X-ray microfocusing with off-axis ellipsoidal mirror

High-precision ellipsoidal mirrors for two-dimensionally focusing X-rays to nanometer sizes have not been realized because of technical problems in their fabrication processes. The objective of the present study is to develop fabrication techniques for ellipsoidal focusing mirrors in the hard-X-ray region. We design an off-axis ellipsoidal mirror for use under total reflection conditions up to the X-ray energy of 8 keV. We fabricate an ellipsoidal mirror with a surface roughness of 0.3 nm RMS (root-mean-square) and a surface figure error height of 3.0 nm RMS by utilizing a surface profiler and surface finishing method developed by us. The focusing properties of the mirror are evaluated at the BL29XUL beamline in SPring-8. A focusing beam size of 270 nm × 360 nm FWHM (full width at half maximum) at an X-ray energy of 7 keV is observed with the use of the knife-edge scanning method. We expect to apply the developed fabrication techniques to construct ellipsoidal nanofocusing mirrors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Rotation of electrothermal-instability-driven overheating structure due to helically oriented surface magnetic field on a high-current-density aluminum rod

Experiments on the 1-MA, 100-ns-rise-time Mykonos Facility demonstrate rotation of electrothermal instability (ETI)-driven overheating structure on 1.00-mm-diameter, 10-nm-surface roughness, 99.999%-pure aluminum rods, which are pulsed with helically polarized surface magnetic field. Rods are machined to include pairs of 10-micron-scale quasi-hemispherical voids or “engineered defects (ED)” which provide the dominant current density perturbation from which ETI grows most rapidly. Experiments include an axial magnetic field component through the addition of a helically wound return-current electrode or “helical return can (HRC).” For a given HRC design, azimuthal field (B ɵ ) and axial field (B z ) components rise at a prescribed and fixed ratio, driving an increasing magnetic field of constant polarization at the rod's surface; most experiments generated surface magnetic field at a 15-degree field polarization angle (from horizontal) defined as ɸ B = arctan(B z /B ɵ ). ETI-driven emission patterns from individual ED are observed to rotate along ɸ B , while emission patterns from dielectric-coated ED pairs are shown to elongate and preferentially merge along ɸ B , in qualitative agreement with 3D-magnetohydrodynamic simulations. These data strongly support that for a randomized distribution of current density perturbations on a high-current density conductor, nearby perturbations will favorably merge about ɸ B , with the degree of merging increasing with current. Such observations offer fundamental new understanding of the seeding mechanisms of the helical magneto-Rayleigh Taylor (MRT) instabilities observed from axially magnetized magnetically driven imploding liners.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comparison of quasi-specular radar scatter from the moon with surface parameters obtained from images

Quasi-specular radar scatter from geologic surfaces displays a variable wavelength dependence in apparent surface roughness. Wavelength dependence will occur whenever a significant fraction of the surface has local radii of curvature comparable to the observing wavelength. This condition can be determined by comparison of the value of the integrated surface curvature spectrum with the radar wavenumber, multiplied by a constant that depends on the geometry. Variations in curvature statistics calculated from photogrammetric reduction of lunar images are consistent with the observed variations in quasi-specular scatter at the same locations. Variations in the strength of the wavelength dependence are correlated with the sizes of lunar craters that lie near the upper size limit for the local steady state distribution. This correlation is also consistent with variations in the curvature spectrum calculated from crater size-frequency distributions.

Tyler, G. L.↗

Analysis of 12-700 micron reflectance spectra of three optical black samples

Normal incidence, specular reflectance spectra of three samples of optical black coatings have been measured in 10 filter passbands at effective wavelengths between 12 and 700 microns. Strong absorption, due to amorphous silicate material in the coatings, is found in the 15-50 micron region of each spectrum. Reflecting-layer model calculations are fitted by a nonlinear least-squares routine to the spectra at wavelengths beyond the absorption band to determine far-infrared optical parameters. It is found that, with a similar wavelength dependence, the absorption coefficient of a new black coating (ECP 2200) made by the Minnesota Mining and Manufacturing Company (3M) is less than 1/10 that of the discontinued coating, 3M Black Velvet Nextel. It is also shown that the extinction effect of a very rough substrate is negligible compared with the effects of increased upper surface roughness and coating thickness attendant upon fully covering a very rough substrate.

Smith, S. M.↗

Interpretation of the surface brightness of Phobos

Analysis of disk resolved images of Phobos obtained by the Phobos 2 spacecraft makes it possible to study the surface scattering law and albedo variations. Low phase angle images reveal variations in local geometric albedo about 10 percent, with a correlation length of about 1 km. The scattering law is reasonably well matched by the recently proposed LPI (Lumme et al., 1990) model, which makes it possible to deduce a small scale (1 mm) surface roughness (0.5), defined here as the rms tangent of the local surface normal relative to the mean surface normal in the Duxbury (1991) model of Phobos. This value is very close to what has been found for Mercury and the moon.

Peltoniemi, Jouni I.↗

Free convection in the Martian atmosphere

Researchers investigated the free convective regime for the Martian atmospheric boundary layer (ABL). Researchers generalized Schumann's model describing horizontal fluctuations and mean vertical gradients occurring during free convection to include convection driven by water vapor gradients and to include the effects of circulation above both aerodynamically smooth and rough surfaces. Applying the model to Mars, researchers found that nearly all the resistance to sensible and latent heat transfer in the ABL occurs within the thin interfacial sublayer at the surface. Free convection is found to readily occur at low pressures and high temperatures when surface ice is present. At 7 mb, the ABL should freely convect whenever the mean windspeed at the top of the surface layer drops below about 2.5 m s(-1) and surface temperatures exceed 250 K. Mean horizontal fluctuations within the surface layer are found to be as high as 3 m (-1) for windspeed, 0.5 K for temperature, and 10 (-4) kg m (-3) for water vapor density. Airflow over surfaces similar to the Antarctic Polar Plateau was found to be aerodynamically smooth on Mars during free convection for all pressures between 6 and 1000 mb, while surfaces with z sub o approx. equals 1 cm are aerodynamically rough over this pressure range.

Clow, G. D.↗