Search NASA⌕ Search

SEARCH · Search NASA

Results for “variational optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Applying Linear Optics from Closed Orbits Modulation for finding beam-based alignment of harmonic sextupoles

A fast and accurate beam-based alignment (BBA) method for harmonic sextupoles has been devel oped at NSLS-II using Linear Optics from Closed Orbit Modulation (LOCOM). The approach excites the beam with simultaneous sine-wave signals at two fast correctors, chosen with an appropriate phase advance to span the full betatron phase space. This strategy suppresses systematic errors from hysteresis, while additional errors from orbit drift and power-supply calibration are minimized by the short measurement time (a few minutes) and reliance solely on beam-based current-to-field conver sion of the sextupoles, with hysteresis explicitly included. Simulations indicate that Linear Optics from Closed Orbits (LOCO) combined with 0.5 mm local orbit bumps can resolve relative sextupole field offsets (∆k₂) with precision better than 10% of k₂, reflecting to beam-based alignment (BBA) accuracy finer than 50 µm. Moreover, employing machine-learning-optimized local orbit bumps en hances sextupole-induced quadrupole signals in a deterministic manner and maintains orbit stability under large sextupole strength variations (±40%). The proposed method is experimentally validated through proof-of-principle measurements at NSLS-II, demonstrating its potential as a fast, precise, and robust tool for harmonic sextupole alignment.

43 PARTICLE ACCELERATORS↗

Automated tuning for HMC mass ratios

We extended previous work on tuning HMC parameters using gradient information to include Hasenbusch mass ratios. The inclusion of mass ratios adds many more parameters that need to be tuned, and also allows for lots of variations in the choice of integrator pattern. We investigate the effectiveness of automatically tuning a large number of HMC parameters and compare the optimally tuned versions over a range of integrator variants.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The cost of noise reduction in commercial tilt rotor aircraft

The relationship between direct operating cost (DOC) and departure noise annoyance was developed for commercial tilt rotor aircraft. This was accomplished by generating a series of tilt rotor aircraft designs to meet various noise goals at minimum DOC. These vehicles were spaced across the spectrum of possible noise levels from completely unconstrained to the quietest vehicle that could be designed within the study ground rules. A group of optimization parameters were varied to find the minimum DOC while other inputs were held constant and some external constraints were met. This basic variation was then extended to different aircraft sizes and technology time frames. It was concluded that reducing noise annoyance by designing for lower rotor tip speeds is a very promising avenue for future research and development. It appears that the cost of halving the annoyance compared to an unconstrained design is insignificant and the cost of halving the annoyance again is small.

Faulkner, H. B.↗

Selection of fluorescence lidar operating parameters for SNR maximization

Fluorescence lidar when applicable offers one of the most sensitive methods for measuring the concentration of trace constituents of the atmosphere. In the conduct of a fluorescence lidar experiment, a number of parameters which can be used to optimize the SNR can be controlled. In this paper the optimum division of laser pulses centered on and off the fluorescence excitation wavelength is calculated as a function of the ratio of the fluorescence signal strength to the strength of fluorescence from interfering species. For strong interference signals the time should be divided equally on and off the line. For strong fluorescence signals the time on line is proportional to the square root of the on-line off-line signal ratio. The optimization of the integration time for varying values of signal-to-background and signal-to-interference ratios, atmospheric attenuation, laser energy variations, background measurement time, and on-line off-line time division is also considered.

Heaps, W. S.↗

Ccds: Their Cause and Cure

Charge coupled devices (CCDs) have opened new horizons in the optical astronomy. Most of the presently existing astronomical CCD systems are oriented and designed primarily for work on faint objects. The use of CCDs for high precision work on bright objects remains to be explored. Issues and problems specific to (CCDs) are covered in detail. The important structural characteristics of CCDs are that they are integrating, self scanned, photon counting (one selection for each detected photon), solid state devices. The typical physical sizes are of the order of 1 - 3 cm, and typical raster formats of 500x500 pixels (TI), 320x512 (RCA), 385x576 (GEC), 800x800 (TI), and 1500x1500 (GEC) should be available soon. Typical (and optimal) operating temperatures are around -100 C, with liquid N2 as the most common coolant. Some CCDs are physically warped. This causes focus variations across the surface, which amount to a spatially variable PSF. Other relevant properties of CCDs as detectors and a comparison with some other astronomical detectors are given.

Djorgovski, S.↗

Neighboring extremal guidance for systems with a piecewise linear control

The neighboring extremal feedback control law is developed for systems with a piecewise linear control for the case where the optimal control is obtained by nonlinear programming techniques. To develop the control perturbation for a given deviation from the nominal path, the second variation is minimized subject to the constraint that the final conditions be satisfied. This process leads to a feedback relationship between the control perturbation and the measured deviation from the nominal state. A simple example, the lunar launch problem, is used to demonstrate the validity of the guidance law. For model errors on the order of 5 percent, the results indicate that 5 percent errors occur in the final conditions.

Hull, David G.↗

Neighboring suboptimal control

The neighboring extremal feedback control law is developed for systems with a piecewise linear control for the case where the optimal control is obtained by nonlinear programming techniques. To develop the control perturbation for a given deviation from the nominal path, the second variation is minimized subject to the constraint that the final conditions be satisfied. This process leads to a feedback relationship between the control perturbation and the measured deviation from the nominal state.

Hull, David G.↗

Integration of Reference Frames Using VLBI

Very Long Baseline Interferometry (VLBI) has the unique potential to integrate the terrestrial and celestial reference frames through simultaneous estimation of positions and velocities of approx. 40 active VLBI stations and a similar number of stations/sites with sufficient historical data, the position and position stability of approx. 150 well-observed extragalactic radio sources and another approx. 500 sources distributed fairly uniformly on the sky, and the time series of the five parameters that specify the relative orientation of the two frames. The full realization of this potential is limited by a number of factors including the temporal and spatial distribution of the stations, uneven distribution of observations over the sources and the sky, variations in source structure, modeling of the solid/fluid Earth and troposphere, logistical restrictions on the daily observing network size, and differing strategies for optimizing analysis for TRF, for CRF and for EOP. The current status of separately optimized and integrated VLBI analysis will be discussed.

Ma, Chopo↗

Mue-Synthesis Robust Control: What's Wrong and how to fix it?

The theory of mue-synthesis introduced in [1,2] provides, in principle, a broadly applicabel theory for the optimal synthesis of multiloop feedback control lows that robustly meet performance and disturbance attenuation specifications despite unknown-but-bounded nonlinearities and parameter variation.

Multiloop Feedback↗

Cohesive Modeling of Transverse Cracking in Laminates with a Single Layer of Elements per Ply

This study aims to bridge the gap between classical understanding of transverse cracking in cross-ply laminates and recent computational methods for the modeling of progressive laminate failure. Specifically, the study investigates under what conditions a finite element model with cohesive X-FEM cracks can reproduce the in situ effect for the ply strength. It is shown that it is possible to do so with a single element across the thickness of the ply, provided that the interface stiffness is properly selected. The optimal value for this interface stiffness is derived with an analytical shear lag model. It is also shown that, when the appropriate statistical variation of properties has been applied, models with a single element through the thickness of a ply can predict the density of transverse matrix cracks

VanDerMeer, Frans P.↗

Model-Based Control of a Nonlinear Aircraft Engine Simulation using an Optimal Tuner Kalman Filter Approach

This paper covers the development of a model-based engine control (MBEC) methodology featuring a self tuning on-board model applied to an aircraft turbofan engine simulation. Here, the Commercial Modular Aero-Propulsion System Simulation 40,000 (CMAPSS40k) serves as the MBEC application engine. CMAPSS40k is capable of modeling realistic engine performance, allowing for a verification of the MBEC over a wide range of operating points. The on-board model is a piece-wise linear model derived from CMAPSS40k and updated using an optimal tuner Kalman Filter (OTKF) estimation routine, which enables the on-board model to self-tune to account for engine performance variations. The focus here is on developing a methodology for MBEC with direct control of estimated parameters of interest such as thrust and stall margins. Investigations using the MBEC to provide a stall margin limit for the controller protection logic are presented that could provide benefits over a simple acceleration schedule that is currently used in traditional engine control architectures.

Control Theory↗

Model-Based Control of an Aircraft Engine using an Optimal Tuner Approach

This paper covers the development of a model-based engine control (MBEC) method- ology applied to an aircraft turbofan engine. Here, a linear model extracted from the Commercial Modular Aero-Propulsion System Simulation 40,000 (CMAPSS40k) at a cruise operating point serves as the engine and the on-board model. The on-board model is up- dated using an optimal tuner Kalman Filter (OTKF) estimation routine, which enables the on-board model to self-tune to account for engine performance variations. The focus here is on developing a methodology for MBEC with direct control of estimated parameters of interest such as thrust and stall margins. MBEC provides the ability for a tighter control bound of thrust over the entire life cycle of the engine that is not achievable using traditional control feedback, which uses engine pressure ratio or fan speed. CMAPSS40k is capable of modeling realistic engine performance, allowing for a verification of the MBEC tighter thrust control. In addition, investigations of using the MBEC to provide a surge limit for the controller limit logic are presented that could provide benefits over a simple acceleration schedule that is currently used in engine control architectures.

Connolly, Joseph W.↗

Successive Convexification for Powered Descent Guidance with Time-Varying Mass Properties

This paper extends the 6 degree-of-freedom successive convexification (SCvx) algorithm discussed in literature to account for time-varying mass properties in the representation of the attitude dynamics. Simulation results of a notional large-size lander performing the last minutes of Lunar powered descent with significant variations in the center-of-mass and moments of inertia over the duration of the trajectory are shown. Differences in the final optimal trajectories generated via SCvx are presented between the constant vs. variable mass property formulations for an in-plane and out-of-plane example.

Alex Hayes↗

Successive Convexification for Powered Descent Guidance with Time-Varying Mass Properties

This paper extends the 6 degree-of-freedom successive convexification (SCvx) algorithm discussed in literature to account for time-varying mass properties in the representation of the attitude dynamics. Simulation results of a notional large-size lander performing the last minutes of Lunar powered descent with significant variations in the center-of-mass and moments of inertia over the duration of the trajectory are shown. Differences in the final optimal trajectories generated via SCvx are presented between the constant vs. variable mass property formulations for an in-plane and out-of-plane example.

Alex Hayes↗

Application of Analytical Heat Transfer Models of Multi-layered Natural and Engineered Barriers in Potential High-Level Nuclear Waste Repositories - 12435

A combination of transient heat transfer analytical solutions for a finite line source, a series of point sources, and a series of parallel infinite line sources were combined with a quasi-steady-state multi-layered cylindrical solution to simulate the temperature response of a deep geologic radioactive waste repository with multi-layered natural and engineered barriers. This evaluation was performed to provide information to scientists and decision makers to compare candidate geologic media for a repository (crystalline rock [granite], clay, salt, and deep borehole), and to provide input for the future evaluation of the trade-off between pre-emplacement surface storage time, waste package size, and repository footprint. This approach was selected in favor of the finite element solution typically used to analyze the temperature response because it allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. The analytical solution approach used to analyze the repository temperature response allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. This approach allowed investigation of the sensitivity of the results to combinations of parameters that show that there is much flexibility to be gained in terms of spent fuel management options by varying a few key parameters. This initial analysis used representative design concepts and thermal constraints based on international design concepts, and it also included waste forms representing future fuel cycles with high burnup fuels. Unlike repository designs with large open tunnels and pre-closure ventilation, all of the disposal concepts analyzed in this study used enclosed emplacement modes, where the waste packages were in direct contact with encapsulating engineered or natural materials. The deep borehole repository concept limits the size of the SNF waste packages and may require rod consolidation to fit within the drill casing diameter. A single assembly waste package, assuming rod consolidation, was evaluated in the current analysis. Similar size restrictions apply for the HLW canisters. At this time no thermal constraints have been defined for the deep borehole repository concept. Representative EBS materials and properties were evaluated. However, changes in EBS design concepts and materials can also have significant effects on the maximum waste package surface temperature. Increased thermal conductivity of the buffer layer can be achieved by using an engineered buffer consisting of a mixture of graphite, sand, and bentonite [14]. One of the advantages of the analytical model is that it highlights the sensitivity of the results to the parameters that define the repository layout, including spacing between axial and lateral neighboring waste packages and drifts. It is clear that repository layout adjustments can be made to reduce the calculated peak temperatures. The results also show that significant reductions in required surface storage times can be achieved if higher thermal constraints can be justified Additional studies are planned to evaluate the trade-offs between surface storage times, repository layout parameters, and variations in EBS design concepts. Model validation and uncertainties will also be addressed. It is expected that shorter surface storage times and more optimized repository design configurations may be achieved. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Use of Design of Experiments in Determining Neural Network Architectures for Loss of Control Detection

We describe empirical methods for selecting a neural network architecture to implement belief state inference on generic commercial transport aircraft. We highlight a case study on the planning, execution, and analysis of a set of experiments to determine the configurations of a conditional variational autoencoder (CVAE). Our main contribution is the application of a structured method that can be used for machine learning in many aerospace applications. This method optimizes the structure and training parameters of a neural network for belief state inference, using Design of Experiments (DOE) statistical methodologies. The motivation for this specific DOE analysis was to identify the appropriate hyperparameters for measuring the CVAE reconstruction probability and latent space, such that the measurements can be used to infer qualitative state changes for the aircraft. We demonstrate that this process yields information about a trained neural network’s utility for this specific application, along with a quantifiable range of certainty. We execute 84 experiments using loss-of-control flight maneuver data from the NASA T 2 aircraft, demonstrating that this empirical process allows us to construct cheap and simple models with specific attributes amenable to belief state inference in aerospace applications.

Loss of Control↗

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗