SEARCH · Search NASA

Results for “Approximation methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

All sources NASA NTRS DOE OSTI

NASA NTRS1990

A three-dimensional upwind parabolized Navier-Stokes code for chemically reacting flows

A new upwind, parabolized Navier-Stokes (PNS) code has been developed to compute the three-dimensional flow of chemically reacting air around hypersonic vehicles. The code is a modification of the perfect gas, three-dimensional UPS code of Lawrence et al. (1986) which has been extended in the present study to permit the calculation of hypersonic, viscous flows in chemical nonequilibrium. The algorithm solves the PNS equations using a finite-volume, upwind TVD method based on Roe's approximate Riemann solver that has been modified to account for real gas effects. The present code solves the fluid dynamic and species continuity equations in a loosely-coupled manner. The fluid medium is assumed to be a chemically reacting mixture of thermally perfect (but calorically imperfect) gases in thermal equilibrium. Results are presented for the hypersonic laminar flow over a cone at 0- and 10-deg angles of attack and for a generic hypersonic vehicle. Calculations are performed assuming either perfect gas, equilibrium air, or finite-rate chemistry.

Buelow, Philip E.↗

NASA NTRS1989

Tilt rotor aircraft aeroacoustics

This paper studies the state of knowledge and the needed improvement in noise methodology and measurements for tilt rotor aircraft. Similarities and differences between tilt rotor aeroacoustic conditions and helicopter and propeller experience are identified. A discussion of the possible principal noise mechanisms throughout the flight envelope shows a need for further experimental and analytical investigations to develop an adequate understanding of the important sources and influencing factors. Existing experimental data from flight tests suggest terminal area noise reduction by operating within certain portions of the conversion flight envelope. Prediction methods are found to provide approximate indications only for low frequency harmonic and broadband noise for several of the tilt rotor's operating conditions. The acoustic effects of the hover case 'fountain' flow are pronounced and need further research. Impulsive noise and high frequency harmonic noise remain problems, as on helicopters, pending major improvements in wake, unsteady aerodynamics, and acoustics methodology.

George, Albert R.↗

NASA NTRS1989

Finite element large-amplitude free and forced vibrations of rectangular thin composite plates

A finite element formulation is presented for determining the large-amplitude free and steady-state forced vibration response of arbitrarily laminated anisotropic composite rectangular thin plates. The nonlinear stiffness and harmonic force matrices of an arbitrarily laminated composite rectangular plate element are developed for nonlinear free and forced vibration analyses. The linearized updated-mode method with nonlinear time function approximation is employed for the solution of the system nonlinear eigenvalue equations. The amplitude-frequency relations for convergence with gridwork refinement, different boundary conditions, aspect ratios, lamination angles and number of plies are presented. The finite element results are compared with available approximate continuum solutions.

Chiang, C. K.↗

NASA NTRS1991

High frequency scattering from corrugated stratified cylinders

Interest in applying radar remote sensing for the study of forested areas led to the development of a model for scattering from corrugated stratified dielectric cylinders. The model is used to investigate the effect of bark and its roughness on scattering from tree trunks and branches. The outer layer of the cylinder (bark) is assumed to be a low-loss dielectric material and to have a regular (periodic) corrugation pattern. The inner layers are treated as lossy dielectrics with smooth boundaries. A hybrid solution based on the moment method and the physical optics approximation is obtained. In the solution, the corrugations are replaced with polarization currents that are identical to those of the local tangential periodic corrugated surface, and the stratified cylinder is replaced with equivalent surface currents. New expressions for the equivalent physical-optics currents are used which are more convenient than the standard ones. It is shown that the bark layer and its roughness both reduce the radar cross-section. It is also demonstrated that the corrugations can be replaced by an equivalent anisotropic layer.

Sarabandi, Kamal↗

NASA NTRS1991

Tunneling calculations for GaAs-Al(x)Ga(1-x) as graded band-gap sawtooth superlattices

Quantum mechanical tunneling calculations for sawtooth (linearly graded band-gap) and step-barrier AlGaAs superlattices were performed by means of a transfer matrix method, within the effective mass approximation. The transmission coefficient and tunneling current versus applied voltage were computed for several representative structures. Particular consideration was given to effective mass variations. The tunneling properties of step and sawtooth superlattices show some qualitative similarities. Both structures exhibit resonant tunneling, however, because they deform differently under applied fields, the J-V curves differ.

Forrest, Kathrine A.↗

NASA NTRS1991

A thermal/nonthermal approach to solar flares

An approach for modeling solar flare high-energy emissions is developed in which both thermal and nonthermal particles coexist and contribute to the radiation. The thermal/nonthermal distribution function is interpreted physically by postulating the existence of DC sheets in the flare region. The currents then provide both primary plasma heating through Joule dissipation, and runaway electron acceleration. The physics of runaway acceleration is discussed. Several methods are presented for obtaining approximations to the thermal/nonthermal distribution function, both within the current sheets and outside of them. Theoretical hard x ray spectra are calculated, allowing for thermal bremsstrahlung from the heated plasma electrons impinging on the chromosphere. A simple model for hard x ray images of two-ribbon flares is presented. Theoretical microwave gyrosynchrotron spectra are calculated and analyzed, uncovering important new effects caused by the interplay of thermal and nonthermal particles. The theoretical spectra are compared with observed high resolution spectra of solar flares, and excellent agreement is found, in both hard x rays and microwaves. The future detailed application of this approach to solar flares is discussed, as are possible refinements to this theory.

Benka, Stephen G.↗

NASA NTRS1992

A solar radiation model for use in climate studies

A solar radiation routine is developed for use in climate studies that includes absorption and scattering due to ozone, water vapor, oxygen, carbon dioxide, clouds, and aerosols. Rayleigh scattering is also included. Broadband parameterization is used to compute the absorption by water vapor in a clear atmosphere, and the k-distribution method is applied to compute fluxes in a scattering atmosphere. The reflectivity and transmissivity of a scattering layer are computed analytically using the delta-four-stream discrete-ordinate approximation. The two-stream adding method is then applied to compute fluxes for a composite of clear and scattering layers. Compared to the results of high spectral resolution and detailed multiple-scattering calculations, fluxes and heating rate are accurately computed to within a few percent. The high accuracy of the flux and heating-rate calculations is achieved with a reasonable amount of computing time. With the UV and visible region grouped into four bands, this solar radiation routine is useful not only for climate studies but also for studies on photolysis in the upper atmosphere and photosynthesis in the biosphere.

Chou, Ming-Dah↗

NASA NTRS1992

A three-dimensional upwind PNS code for chemically reacting scramjet flowfields

A new upwind, parabolized Navier-Stokes (PNS) code has been developed to compute the three-dimensional (3D) chemically reacting flow in scramjet (supersonic combustion ramjet) engines. The code is a modification of the 3D upwind PNS (UPS) airflow code which has been extended in the present study to permit internal flow calculations with hydrogen-air chemistry. With these additions, the new code has the capability of computing aerodynamic and propulsive flowfields simultaneously. The algorithm solves the PNS equations using a finite-volume, upwind TVD method based on Roe's approximate Riemann solver that has been modified to account for 'real gas' effects. The fluid medium is assumed to be a chemically reacting mixture of thermally perfect (but calorically imperfect) gases in thermal equilibrium. The new code has been applied to two test cases. These include the Burrows-Kurkov supersonic combustion experiment and a generic 3D scramjet flowfield. The computed results compare favorably with the available experimental data.

Wadawadigi, Ganesh↗

NASA NTRS1993

Controls-structures-interaction dynamics during RCS control of the Orbiter/SRMS/SSF configuration

During the assembly flights of the Space Station Freedom (SSF), the Orbiter will either dock with the SSF and retract to the final berthed position, or will grapple the SSF using the Shuttle Remote Manipulator System (SRMS) and maneuver the SRMS coupled vehicles to their final berthed position. The SRMS method is expected to take approximately one to one and a half hours to complete and require periodic attitude corrections by either the Orbiter or the SSF reaction control system (RCS) or continuous control by a control moment gyro (CMG) system with RCS desaturation as required. Free drift of the attached vehicles is not currently thought to be acceptable because the desired system attitude will quickly deteriorate due to unbalanced gravity gradient and aerodynamic torques resulting in power generation problems, thermodynamic control problems, and communications problems. This paper deals with the simulation and control of the SRMS during trunnion/latch interaction dynamics and during RCS maneuvers. The SRMS servo drive joints have highly non-linear elastic characteristics which tend to degrade sensitive control strategies. In addition the system natural frequencies are extremely low and depend on the drive joint deflections and SRMS geometric position. The lowest mean period of oscillation for the Orbiter/SRMS/SSF(MB6) system in brakes hold mode positioned near the final berthed position is approximately 120 seconds. A detailed finite element model of the SRMS has been developed and used in a newly developed SRMS systems dynamics simulation to investigate the non-linear transient response dynamics of the Orbiter/SRMS/SSF systems. The present SRMS control strategy of brakes only recommended by the Charles Draper Labs is contrasted with a robust controller developed by the authors. The robust controller uses an optimal inear quadratic regulator (LQR) to optimally place the closed-loop poles of a multivariable continuous-time system within the common region of an open sector with the sector angle plus or minus 45 degrees from the negative real axis, and the left-hand side of a parallel to the imaginary axis in the complex s-plane. This guarantees that the critical damping ratio for the desired control modes is equal to or in excess of 0.707. The matrix sign function is used for solving the Riccati equations which appear in the controller design procedure. Fast and stable algorithms have recently been developed for the computation of the matrix sign function. Simulation results are given which demonstrate the potential CSI involvement for the current SRMS control system and the proposed control system.

Schliesing, J. A.↗

NASA NTRS1993

A note on the computation of antenna-blocking shadows

A simple and readily applied method is provided to compute the shadow on the main reflector of a Cassegrain antenna, when cast by the subreflector and the subreflector supports. The method entails some convenient minor approximations that will produce results similar to results obtained with a lengthier, mainframe computer program.

Levy, R.↗

NASA NTRS1992

Radiative equilibrium in rapidly expanding shells

The equation of radiative equilibrium for rapidly expanding spherical shells including the special relativistic terms is discussed, and a temperature-correction procedure for the solution of this equation is given. The temperature-correction scheme combines a partial linearization approach with the approximate Lambda-operator iteration method. For some test problems, the temperature structures of atmospheres in radiative equilibrium in the Lagrangian frame are calculated. The effects of the velocity field on the temperature stratification and the luminosity are also discussed. We find that the temperature structure of a moving photosphere in radiative equilibrium in the Lagrangian frame differs significantly from that of a static photosphere and that, at least, all first-order terms, in particular the advection and aberration terms, have to be included consistently both in the radiative transfer and the energy equation in studies of supernovae atmospheres and other high-speed radiating flows.

Hauschildt, P. H.↗

NASA NTRS1992

Identification and feedback control in structures with piezoceramic actuators

In this lecture we give fundamental well-posedness results for a variational formulation of a class of damped second order partial differential equations with unbounded input or control coefficients. Included as special cases in this class are structures with piezoceramic actuators. We consider approximation techniques leading to computational methods in the context of both parameter estimation and feedback control problems for these systems. Rigorous convergence results for parameter estimates and feedback gains are discussed.

Banks, H. T.↗

NASA NTRS1993

Nonlinear vibrations of thin arbitrarily laminated composite plates subjected to harmonic excitations using DKT elements

A finite element formulation is presented for determining the large-amplitude free and steady-state forced vibration response of arbitrarily laminated anisotropic composite thin plates using the Discrete Kirchhoff Theory (DKT) triangular elements. The nonlinear stiffness and harmonic force matrices of an arbitrarily laminated composite triangular plate element are developed for nonlinear free and forced vibration analyses. The linearized updated-mode method with nonlinear time function approximation is employed for the solution of the system nonlinear eigenvalue equations. The amplitude-frequency relations for convergence with gridwork refinement, triangular plates, different boundary conditions, lamination angles, number of plies, and uniform versus concentrated loads are presented.

Chiang, C. K.↗

NASA NTRS1992

Production of H-3 at large momentum in alpha-(C-12) collisions at 2A GeV

Calculations of the longitudinal and transverse momentum distributions for H-3 production at large momentum in alpha-(C-12) collisions near 2A GeV are compared to experiment. Triton exchange and final-state interactions are shown to represent large corrections to the impulse approximation for proton knockout. A method for calculating interference effects for inelastic fragmentation is discussed. Good agreement with experiment using a phenomenological overlap function for (H-3)-p is found successful in describing H-3 production in pion-induced reactions. Comparisons to momentum distributions obtained through (p, 2p) and (e, ep) reactions on He-4 are made.

Cucinotta, Francis A.↗

NASA NTRS1993

The effect of grid aspect ratio on convergence

Vector stability theory and computational experiments are used to examine the effects of high aspect ratio grids on algorithm convergence. Emphasis is placed on identifying the degree of convergence deterioration that ADI schemes experience as grid aspect ratio increases and on deriving methods for circumventing this problem. Approximately factored implicit schemes are found to experience convergence deterioration because of nonoptimum local time stepping procedures and the increased need for viscous preconditioning. An enhanced algorithm is devised on the basis of improved selection of the local time step, appropriate definition of viscous preconditioning matrix, and proper implementation of boundary conditions. The novel algorithm provides uniformly efficient convergence at all aspect ratios for both Euler and Navier-Stokes computations for a variety of test problems.

Buelow, P. E. O.↗

NASA NTRS1952

Experimental Investigation of Eccentricity Ratio, Friction, and Oil Flow of Short Journal Bearings

An experimental investigation was conducted to obtain performance data on bearings of length-diameter ratios of 1, 1/2, and 1/4 for comparison with theoretical curves. A 1.375-inch-diameter bearing was tested at speeds up to 6000 rpm and with unit loads from 0 to 900 pounds per square inch. Experimental data for eccentricity ratio and friction followed single lines when plotted against a theoretically derived capacity number, which is equal to Sommerfeld number times the square of the length-diameter ratio. The form of the capacity number indicates that under certain conditions the eccentricity ratio is theoretically independent of bearing diameter. A method of plotting oil flow data as a single line is shown. Methods are also discussed for approximating a maximum bearing temperature and evaluating the effect of deflection or misalignment on the eccentricity ratio at the ends of the bearings.

BEARINGS, SLEEVE↗

NASA NTRS1957

Practical solution of plastic deformation problems in elastic-plastic range

A practical method for solving plastic deformation problems in the elastic-plastic range is presented. The method is one of successive approximations and is illustrated by four examples which include a flat plate with temperature distribution across the width, a thin shell with axial temperature distribution, a solid cylinder with radial temperature distribution, and a rotating disk with radial temperature distribution.

COLUMNS, TUBULAR↗

NASA NTRS1993

A study of strength evaluations of EDNi/EDCu/NARloy-Z bonded joints

Dissimilar material interfaces can be found in many materials and structural bonds such as composite materials, welded parts, inclusion in matrix, bond between metallic and ceramic materials, and so forth. One of such structural bonds can be seen in the main combustion chamber (MCC) of the Space Shuttle Main Engine (SSME). In this study, from a practical sense, the primary concern is to understand the systems response of EDNi/EDCu/NARloy-Z bonded joints using stress values approximated by the finite element method to determine an influence of the variation of structural bond parameters on the bonded joints, and consequently main combustion chamber of the Space Shuttle Main Engine. The results presented in this study could be an appropriate indicator for a good bond of EDNi/DECu/NARloy-Z layers with the desired thickness of copper deposition in the SSME MCC manufacturing process. Furthermore, the results from this study appear to be applicable to any bonded joints that can be characterized by the parameters and assumptions used in this analysis.

Min, J. B.↗