Search NASA⌕ Search

SEARCH · Search NASA

Results for “CASE METHOD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Fidelity-optimized quantum state estimation

We describe an optimized, self-correcting procedure for the Bayesian inference of pure quantum states. By analyzing the history of measurement outcomes at each step, the procedure returns the most likely pure state, as well as the optimal basis for the measurement that is to follow. The latter is chosen to maximize, on average, the fidelity of the most likely state after the measurement. We also consider a practical variant of this protocol, where the available measurement bases are restricted to certain limited sets of bases. We demonstrate the success of our method by considering in detail the single-qubit and two-qubit cases, and comparing the performance of our method against other existing methods.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sample Complexity of Power System State Estimation Using Matrix Completion

In this paper, we propose an analytical framework to quantify the amount of data samples needed to obtain accurate state estimation in a power system - a problem known as sample complexity analysis in computer science. Motivated by the increasing adoption of distributed energy resources into the distribution-level grids, it becomes imperative to estimate the state of distribution grids in order to ensure stable operation. Traditional power system state estimation techniques mainly focus on the transmission network which involve solving an overdetermined system and eliminating bad data. However, distribution networks are typically underdetermined due to the large number of connection points and high cost of pervasive installation of measurement devices. In this paper, we consider the recently proposed state-estimation method for underdetermined systems that is based on matrix completion. In particular, a constrained matrix completion algorithm was proposed, wherein the standard matrix completion problem is augmented with additional equality constraints representing the physics (namely power-flow constraints). We analyze the sample complexity of this general method by proving an upper bound on the sample complexity that depends directly on the properties of these constraints that can lower number of needed samples as compared to the unconstrained problem. To demonstrate the improvement that the constraints add to state estimation, we test the method on a 141-bus distribution network case study and compare it to the traditional least squares minimization state estimation method.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Polarization filtering of SAR data

A theoretical analysis of polarization filtering for the bistatic case is developed for optimum discrimination between two types of targets. The resulting method is half analytical and half numerical. Because it is based on the Stokes matrix representation, the targets of interest can be extended targets. The scattered field from such targets is partially polarized. This method is then applied to the monostatic case with numerical examples relying on the JPL (Jet Propulsion Laboratory) full-polarimetric L-band radar data. A matched filter to maximize the power ratio between urban and natural targets is developed. The results show that the same filter is optimal for both ocean and forest targets as natural targets.

Dubois, Pascale C.↗

Sample Complexity of Power System State Estimation using Matrix Completion: Preprint

In this paper, we propose an analytical framework to quantify the amount of data samples needed to obtain accurate state estimation in a power system-a problem known as \emph{sample complexity} analysis in computer science. Motivated by the increasing adoption of distributed energy resources into the distribution-level grids, it becomes imperative to estimate the state of distribution grids in order to ensure stable operation. Traditional power system state estimation techniques mainly focus on the transmission network which involve solving an overdetermined system and eliminating bad data. However, distribution networks are typically \emph{underdetermined} due to the large number of connection points and high cost of pervasive installation of measurement devices. In this paper, we consider the recently proposed state-estimation method for underdetermined systems that is based on \emph{matrix completion}. In particular, a \emph{constrained} matrix completion algorithm was proposed, wherein the standard matrix completion problem is augmented with additional equality constraints representing the physics (namely power-flow constraints). We analyze the sample complexity of this general method by proving an upper bound on the sample complexity that depends directly on the properties of these constraints that can lower number of needed samples as compared to the unconstrained problem. To demonstrate the improvement that the constraints add to state estimation, we test the method on a 141-bus distribution network case study and compare it to the traditional least squares minimization state estimation method.

24 POWER TRANSMISSION AND DISTRIBUTION↗

A Lagrangian dual method for two-stage robust optimization with binary uncertainties

This report presents a new exact method to calculate worst-case parameter realizations in two-stage robust optimization problems with categorical or binary-valued uncertain data. Traditional exact algorithms for these problems, notably Benders decomposition and column-and-constraint generation, compute worst-case parameter realizations by solving mixed-integer bilinear optimization subproblems. However, their numerical solution can be computationally expensive not only due to their resulting large size after reformulating the bilinear terms, but also because decision-independent bounds on their variables are typically unknown. We propose an alternative Lagrangian dual method that circumvents these difficulties and is readily integrated in either algorithm. We specialize the method to problems where the binary parameters switch on or off constraints as these are commonly encountered in applications, and discuss extensions to problems that lack relatively complete recourse and to those with integer recourse. Numerical experiments provide evidence of significant computational improvements over existing methods.

42 ENGINEERING↗

Local heat transfer measurement with liquid crystals on rotating surfaces including non-axisymmetric cases

An overview and summary of test methods and results are given for the problem of measuring local heat transfer on rotating surfaces that model gas turbine engine disks. Disk cavity situations generically similar to those encountered in the high pressure stage disk cooling are considered, with cooling air supplied both at or near the wheel centerline as well as through single or multiple jets impinging outboard on the wheel near the blade attachment region. In some situations provision has been made for ingestion into the disk-cavity from the gas path region radially outboard of the disk. Local heat transfer rates in all cases are determined from the color display from a thin coating of encapsulated liquid crystals sprayed onto the disk, in conjunction with use of a video camera and computer vision system. For cases with axisymmetric disk surfaces, the coated surfaces are illuminated and viewed continuously, and detailed radial distributions of local Nusselt number are obtained. For non-axisymmetric disk surfaces, such as encountered in the vicinity of bolt heads, the disk is illuminated with stroboscopic light, and a method has been developed and used to synchronize the computer frame grabber with the illumination.

Metzger, D. E.↗

TU-AB-202-10: How Effective Are Current Atlas Selection Methods for Atlas-Based Auto-Contouring in Radiotherapy Planning?

Purpose: To investigate the effectiveness of atlas selection methods for improving atlas-based auto-contouring in radiotherapy planning. Methods: 275 H&N clinically delineated cases were employed as an atlas database from which atlases would be selected. A further 40 previously contoured cases were used as test patients against which atlas selection could be performed and evaluated. 26 variations of selection methods proposed in the literature and used in commercial systems were investigated. Atlas selection methods comprised either global or local image similarity measures, computed after rigid or deformable registration, combined with direct atlas search or with an intermediate template image. Workflow Box (Mirada-Medical, Oxford, UK) was used for all auto-contouring. Results on brain, brainstem, parotids and spinal cord were compared to random selection, a fixed set of 10 “good” atlases, and optimal selection by an “oracle” with knowledge of the ground truth. The Dice score and the average ranking with respect to the “oracle” were employed to assess the performance of the top 10 atlases selected by each method. Results: The fixed set of “good” atlases outperformed all of the atlas-patient image similarity-based selection methods (mean Dice 0.715 c.f. 0.603 to 0.677). In general, methods based on exhaustive comparison of local similarity measures showed better average Dice scores (0.658 to 0.677) compared to the use of either template image (0.655 to 0.672) or global similarity measures (0.603 to 0.666). The performance of image-based selection methods was found to be only slightly better than a random (0.645). Dice scores given relate to the left parotid, but similar results patterns were observed for all organs. Conclusion: Intuitively, atlas selection based on the patient CT is expected to improve auto-contouring performance. However, it was found that published approaches performed marginally better than random and use of a fixed set of representative atlases showed favourable performance. This research was funded via InnovateUK Grant 600277 as part of Eurostars Grant E!9297. DP,BS,MG,TK are employees of Mirada Medical Ltd.

60 APPLIED LIFE SCIENCES↗

Methodology for sensitivity analysis, approximate analysis, and design optimization in CFD for multidisciplinary applications

In this study involving advanced fluid flow codes, an incremental iterative formulation (also known as the delta or correction form) together with the well-known spatially-split approximate factorization algorithm, is presented for solving the very large sparse systems of linear equations which are associated with aerodynamic sensitivity analysis. For smaller 2D problems, a direct method can be applied to solve these linear equations in either the standard or the incremental form, in which case the two are equivalent. Iterative methods are needed for larger 2D and future 3D applications, however, because direct methods require much more computer memory than is currently available. Iterative methods for solving these equations in the standard form are generally unsatisfactory due to an ill-conditioning of the coefficient matrix; this problem can be overcome when these equations are cast in the incremental form. These and other benefits are discussed. The methodology is successfully implemented and tested in 2D using an upwind, cell-centered, finite volume formulation applied to the thin-layer Navier-Stokes equations. Results are presented for two sample airfoil problems: (1) subsonic low Reynolds number laminar flow; and (2) transonic high Reynolds number turbulent flow.

Taylor, Arthur C., III↗

Coupling CFD and Material Response for Analysis of Mars Entry

In computing the response of an ablating thermal protection system during atmospheric entry, the aerothermal environment and material response are generally computed separately with a blowing correction term in the material response model to account for the blowing of char and pyrolysis gases [1]. In this work, we apply a coupled approach in which pyrolysis blowing gases, computed in the PATO material response code [2], are used with a blowing boundary condition in the DPLR hypersonic CFD code [3]. This leads to an iterative method in which blowing products from PATO are input into DPLR to update surface heating estimates. The full iterative method, with the addition of radiative heating estimates using the NEQAIR radiation solver [4], is shown in Fig. 1. The method is demonstrated on a sphere case with the environment and material properties based on the Mars Science Laboratory entry. Future work includes utilizing this method in computing full 3D material response during the Mars 2020 entry.

Heat Transfer↗

Coupling CFD and Material Response for Analysis of Mars Entry

In computing the response of an ablating thermal protection system during atmospheric entry, the aerothermal environment and material response are generally computed separately with a blowing correction term in the material response model to account for the blowing of char and pyrolysis gases. In this work, we apply a coupled approach in which pyrolysis blowing gases, computed in the PATO material response code, are used with a blowing boundary condition in the DPLR hypersonic CFD code. This leads to an iterative method in which blowing products from PATO are input into DPLR to update surface heating estimates. The full iterative method, with the addition of radiative heating estimates using the NEQAIR radiation solver, is shown in Fig. 1. The method is demonstrated on a sphere case with the environment and material properties based on the Mars Science Laboratory entry. Future work includes utilizing this method in computing full 3D material response during the Mars 2020 entry.

Ablation↗

A Hybrid Reinforcement Learning-MPC Approach for Distribution System Critical Load Restoration: Preprint

This paper proposes a hybrid control approach for distribution system critical load restoration, combining deep reinforcement learning (RL) and model predictive control (MPC) aiming at maximizing total restored load following an extreme event. RL determines a policy for quantifying operating reserve requirements, thereby hedging against uncertainty, while MPC models grid operations incorporating RL policy actions, i.e., the reserve requirement, renewable (wind and solar) power predictions, and load demand forecasts. We formulate the reserve requirement determination problem as a sequential decision making problem based on the Markov Decision Process (MDP) and design an RL learning environment based on the OpenAI Gym framework and MPC. The RL agent reward and MPC objective function aim to maximize and monotonically increase total restored load and minimize load shedding and renewable power curtailment. The RL algorithm is trained off-line using historical forecast of renewable generation and load demand. The method is tested using a modified IEEE 13-bus distribution test feeder containing wind turbine, photovoltaic, microturbine and battery. Case studies demonstrated that the proposed method outperforms other operating reserve determination methods.

distribution system↗

A Hybrid Reinforcement Learning-MPC Approach for Distribution System Critical Load Restoration

This paper proposes a hybrid control approach for distribution system critical load restoration, combining deep reinforcement learning (RL) and model predictive control (MPC) aiming at maximizing total restored load following an extreme event. RL determines a policy for quantifying operating reserve requirements, thereby hedging against uncertainty, while MPC models grid operations incorporating RL policy actions (i.e., reserve requirements), renewable (wind and solar) power predictions, and load demand forecasts. We formulate the reserve requirement determination problem as a sequential decision-making problem based on the Markov Decision Process (MDP) and design an RL learning environment based on the OpenAI Gym framework and MPC simulation. The RL agent reward and MPC objective function aim to maximize and monotonically increase total restored load and minimize load shedding and renewable power curtailment. The RL algorithm is trained offline using a historical forecast of renewable generation and load demand. The method is tested using a modified IEEE 13-bus distribution test feeder containing wind turbine, photovoltaic, microturbine, and battery. Case studies demonstrated that the proposed method outperforms other policies with static operating reserves.

distribution system↗

Calculating Radiation Damage (DPA) from Transmutation Products

This is a poster for an INL poster session. Accurate models for radiation damage are crucial for predicting material performance in radiation environments. The uncertainty of state-of-the-art radiation damage models is large, contributing to excessive safety margins. A major source of this uncertainty is neglecting the effect that transmutation products have on radiation damage. Transmutation products are new nuclides formed by neutron activation during irradiation; they can contribute to radiation damage by additional neutron capture or decay events. Ignoring the contribution of transmutation products leads to a significant underprediction of the radiation damage (e.g., >10% error in 316 stainless steel). This underprediction is accounted for in part by adding larger safety margins to designs. Currently, the state of the art explicitly accounts for only a single transmutation product, namely nickel-59, during the radiation damage calculation. All other transmutation products are assumed to not contribute to the radiation damage, because there is currently no established method to systematically track all or a selection of radiation damage contributions of transmutation products during activation. In the case of nickel-59, the current method is to apply a precalculated correlation that cannot be used for any other nuclide and is largely dependent on all nuclear engineers being experts in this niche topic. This project proposed to methodically find other transmutation products that cause significant radiation damage, and then to develop a general framework for systematically tracking the radiation damage from these nuclides. This was accomplished by combining the radiation damage calculation into the transmutation calculation already performed for irradiated structural materials. The key idea of our framework is to introduce radiation-damage "pseudo-nuclides" to the list of nuclides used in the transmutation analysis. This allows radiation damage to be tracked alongside the creation and destruction of transmutation products. The main deliverable of this project is a general framework for computing radiation damage while the damaged material undergoes transmutation; this capability allows a significantly more accurate estimation of radiation damage, and in turn reduce required safety margins thereby reducing the cost to construct reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Magnetoelectric effects in multiferroic fibrous composite with imperfect interface

This paper investigates the magnetoelectroelastic responses of multiferroic fibrous composites with imperfectly bonded interface under longitudinal shear. The proposed imperfect interface model is a natural generalization of the shear lag (or the spring layer) model. By virtue of the complex variable method, we first consider the case where an isolated circular multiferroic fiber is imperfectly bonded to an infinite multiferroic matrix. Very concise expressions for the complex field potentials characterizing the magnetoelectroelastic fields inside and outside the circular fiber are obtained when the matrix is subjected to the remote uniform magnetoelectroelastic loading. The Mori-Tanaka mean-field method is then employed to derive the effective moduli of the multiferroic fibrous composite made of randomly distributed fibers reinforced to the matrix. Particularly we demonstrate that the interfacial imperfection in elasticity, electricity, and magnetism will always cause a significant reduction in the magnetoelectric coefficient of the BaTiO{sub 3}-CoFe{sub 2}O{sub 4} fibrous composite.

36 MATERIALS SCIENCE↗

Kummel Disease Treatment by Unipedicular Vertebral Augmentation Using Curved Injection Cannula

Purpose: This study was designed to evaluate the efficacy of the blunt-tipped curved injection needle (BCN) AVAflex (Care Fusion) for vertebral augmentation in cases of Kummel's disease. Methods: We performed 25 vertebral augmentation procedures on 25 consecutive patients (11 men/14 women; mean age, 67 years) with Kummel's disease using the blunt-tipped curved injection needle with PMMA cement. We performed all 25 procedures by unipedicular left approach with patients in prone position under local anesthesia and mild sedation. In all cases, an intravertebral cleft was evident on preprocedural imaging. We evaluated pain intensities by Visual Analogic Scale (VAS) before and at first day, 6 months, and 1 year after procedure. Results: In all cases the curved injection cannula permitted the filling of the clefts and surrounding cancellous bone without any complication. A significant reduction of kyphotic deformities of the treated vertebral bodies was evident. A significance decrease in VAS values at 1 year also was evident (mean decrease 7.2). At plain dynamic postprocedural X-rays checks, there was no sign of pathologic intravertebral motion as evidence of optimal stabilization. Conclusions: BCN AVAflex is a safe and effective device for targeted vertebral augmentation in cases of Kummel's disease. Its distinctive characteristic is the curved injection cannula, which enables targeting the cement injection to areas far off the trajectory of the straight access cannula, thus providing excellent cement spread throughout the entire volume of vertebral body.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Reasoning with case histories of process knowledge for efficient process development

The significance of compiling case histories of empirical process knowledge and the role of such histories in improving the efficiency of manufacturing process development is discussed in this paper. Methods of representing important investigations as cases and using the information from such cases to eliminate redundancy of empirical investigations in analogous process development situations are also discussed. A system is proposed that uses such methods to capture the problem-solving framework of the application domain. A conceptual design of the system is presented and discussed.

Bharwani, Seraj S.↗

A technique for deriving column-integrated water content using VAS split-window data

An algorithm is examined that uses VISSR Atmospheric Sounder (VAS) 11- and 12-micron (split-window) data to derive column-integrated water content (IWC) at mesoscale resolution. The algorithm is physically based and derives its first-guess information from radiosonde data. The procedure is applied first to a test case data set and then to the 19 June 1986 study day from the Cooperative Huntsville Meteorological Experiment (COHMEX). Ground truth data for verifying results from the technique include IWC from National Weather Service and COHMEX radiosondes, the Multispectral Atmospheric Mapping Sensor (MAMS), and a special set of VAS soundings (12 channel) using an independent retrieval method. Results from the test case show reasonable accuracy with the rms errors as low as +/- 3.8 mm. On the 19 June case study day IWC analyses depict reasonable gradients and exhibit good spatial and temporal continuity. Furthermore, they provide insight into preferred regions for cumulus cloud and thunderstorm formation. On the average, a mean absolute retrieval error of 2.4 mm (an 8.1 percent error) and a rms error of +/- 2.9 mm are obtained on the case study day. These results compare favorably with those from existing VAS IWC techniques. Overall, the findings indicate that the technique has excellent potential to depict mesoscale moisture variations.

Guillory, Anthony R.↗

Calculation of narrower confidence intervals for tree mortality rates when we know nothing but the location of the death/survival events

Abstract Many ecological applications, like the study of mortality rates, require the estimation of proportions and confidence intervals for them. The traditional way of doing this applies the binomial distribution, which describes the outcome of a series of Bernoulli trials. This distribution assumes that observations are independent and the probability of success is the same for all the individual observations. Both assumptions are obviously false in many cases. I show how to apply bootstrap and the Poisson binomial distribution (a generalization of the binomial distribution) to the estimation of proportions. Any information at the individual level would result in better (narrower) confidence intervals around the estimation of proportions. As a case study, I applied this method to the calculation of mortality rates in a forest plot of tropical trees in Lambir Hills National Park, Malaysia. I calculated central estimates and 95% confidence intervals for species‐level mortality rates for 1,007 tree species. I used a very simple model of spatial dependence in survival to estimate individual‐level risk of mortality. The results obtained by accounting for heterogeneity in individual‐level risk of mortality were comparable to those obtained with the binomial distribution in terms of central estimates, but the precision increased in virtually all cases, with an average reduction in the width of the confidence interval of ~20%. Spatial information allows the estimation of individual‐level probabilities of survival, and this increases the precision in the estimates of mortality rates. The general method described here, with modifications, could be applied to reduce uncertainty in the estimation of proportions related to any spatially structured phenomenon with two possible outcomes. More sophisticated approaches can yield better estimates of individual‐level mortality and thus narrower confidence intervals.

59 BASIC BIOLOGICAL SCIENCES↗