Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Interferometric SAR for observation of glacier motion and firn penetration

A digital elevation model (DEM) for a swath in west Greenland above Jakobshavn Isbrae derived from a number ERS-1 interferograms combined so as to reduce phase errors and other problems is presented. The DEM shows a wealth of kilometer-scale, dynamically supported topography, which arises from ice sheet flow over the rough bed. A correlation is shown between topography and interferometric phase due solely to ice sheet motion, which clearly shows the translations of scatterers in the surface up and downslope in the topography. Finally, the low correlation in interferograms of ice sheet dry snow zones motivates investigation on the depth-locus of backscattering. A scattering model is presented, including realistic firn grain size distributions and layering, which shows that layering helps to localize backscattering from dry firn to shallower depths than would otherwise be expected.

Winebrenner, Dale P.↗

WE-D-BRA-03: Four-Dimensional Dose Reconstruction Through Retrospective Phase Determination Using Cine Images of Electronic Portal Imaging Device

Purpose: To test a method to reconstruct a four-dimensional (4D) dose distribution using the correlation of pre-calculated 4D electronic portal imaging device (EPID) images and measured cine-EPID images. Methods: 1. A phantom designed to simulate a tumor in lung (a polystyrene block with 3.0 cm diameter embedded in cork) was placed on a sinusoidally moving platform with 2 cm amplitude and 4 sec/cycle. Ten-phase 4D CT images were acquired for treatment planning and dose reconstruction. A 6MV photon beam was irradiated on the phantom with static (field size=5×8.5 cm{sup 2}) and dynamic fields (sliding windows, 10×10 cm{sup 2}, X1 MLC closing in parallel with the tumor movement). 2. 4D and 3D doses were calculated forwardly on PTV (1 cm margin). 3. Dose images on EPID under the fields were calculated for 10 phases. 4. Cine EPID images were acquired during irradiation. 5. Their acquisition times were correlated to the phases of the phantom at which irradiation occurred by inter-comparing calculated “reference” EPID images with measured images (2D gamma comparison). For the dynamic beam, the tumor was hidden under MLCs during a portion of irradiation time; the correlation performed when the tumor was visible was extrapolated. 6. Dose for each phase was reconstructed on the 4D CT images and summed over all phases. The summation was compared with forwardly calculated 4D and 3D dose distributions. Monte Carlo methods were used for all calculations. Results: For the open and dynamic beams, the 4D reconstructed doses showed the pass rates of 92.7 % and 100 %, respectively, at the isocenter plane given 3% / 3 mm criteria. The better agreement of the dynamic beam was from its dose gradient which blurred the otherwise sharp difference between forward and reconstructed doses. This also contributed slightly better agreement in DVH of PTV. Conclusion: The feasibility of 4D reconstruction was demonstrated.

60 APPLIED LIFE SCIENCES↗

Neutron imaging of diabatic two-phase flows relevant to air conditioning

The design of the evaporator of an air conditioning system relies heavily on heat transfer coefficients and pressure drop correlations that predominantly involve an estimate of the changing void fraction and the underlying two-phase flow regime. These correlations dictate whether the resulting heat exchanger is oversized or not and the amount of refrigerant charge necessary to operate. The latter is particularly important when dealing with flammable or high GWP refrigerants. Traditional techniques to measure the void fraction and visualize the flow are either invasive to the flow or occur downstream of the evaporator, where some of the flow distribution will have changed. Neutron imaging has the potential to visualize two-phase flow in-situ where an aluminium heat exchanger structure becomes essentially transparent to the penetrating neutrons. The subatomic particles are attenuated by the passing refrigerant flow. The resulting image may be directly related to the void fraction and the overall picture provides a clear insight into the flow regime present. This work presents neutron images of the refrigerant Isopentane as it passes through the flow channels of an aluminium evaporator at flowrates relevant to air conditioning. The flow in a 4mm square macro channel is compared to that in a 250 m by 750 m rectangular microchannel in terms of void fraction and regime. All neutron imaging experiments were conducted at the High Flux Isotope Reactor, an Oak Ridge National Laboratory facility

Geoghegan, Patrick J↗

Numerical Study of Quantum Hall Bilayers at Total Filling ν T = 1 : A New Phase at Intermediate Layer Distances

We view the phase diagram of quantum Hall bilayer systems with total filing ν T = 1/2 + 1/2 of the lowest Landau level as a function of layer distances d . Based on numerical exact diagonalization calculations, we obtain three distinct phases, including an exciton superfluid phase with spontaneous interlayer coherence at small d , a composite Fermi liquid at large d , and an intermediate phase for 1.1 < d/l B < 1.8 (l B is the magnetic length). The transition from the exciton superfluid to the intermediate phase is identified by (i) a dramatic change in the Berry curvature of the ground state under twisted boundary conditions on the two layers and (ii) an energy level crossing of the first excited state. The transition from the intermediate phase to the composite Fermi liquid is identified by the vanishing of the exciton superfluid stiffness. Moreover, from our finite-size study, the energy cost of transferring one electron between the layers shows an even-odd effect and possibly extrapolates to a finite value in the thermodynamic limit, indicating the enhanced intralayer correlation. Our identification of an intermediate phase and its distinctive features shed new light on the theoretical understanding of the quantum Hall bilayer system at total filling ν T = 1 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A phase screen model for simulating numerically the propagation of a laser beam in rain

The method based on the generalisation of the phase screen method for a continuous random medium is proposed for simulating numerically the propagation of laser radiation in a turbulent atmosphere with precipitation. In the phase screen model for a discrete component of a heterogeneous 'air-rain droplet' medium, the amplitude screen describing the scattering of an optical field by discrete particles of the medium is replaced by an equivalent phase screen with a spectrum of the correlation function of the effective dielectric constant fluctuations that is similar to the spectrum of a discrete scattering component - water droplets in air. The 'turbulent' phase screen is constructed on the basis of the Kolmogorov model, while the 'rain' screen model utiises the exponential distribution of the number of rain drops with respect to their radii as a function of the rain intensity. Theresults of the numerical simulation are compared with the known theoretical estimates for a large-scale discrete scattering medium. (propagation of laser radiation in matter)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measuring B{sub s} width difference at the {Upsilon}(5s) using quantum entanglement

About 90% of B{sub s}B{sub s} pairs produced at the {Upsilon}(5s) resonance are initially B{sub s}{sup *}B{sub s}{sup *} pairs which decay radiatively to B{sub s}B{sub s}. This implies that the B{sub s}B{sub s} pair will then be in an eigenstate of charge conjugation (i.e. C=-1) and therefore in an entangled state. This allows for a determination of {Delta}{Gamma}{sub s}/{Gamma}{sub s} and the CP phase using a number of possible correlations between the decays of the two B{sub s} mesons. In particular, we consider the time integrated correlation, the time ordering asymmetry, and the time ordering-charge asymmetry, which in addition to time ordering distinguishes B{sub s} from B{sub s}, for various combinations of final states. With the statistics of about O(10{sup 7}-10{sup 8}) {Upsilon}(5s) events available at B factories, we find that the time ordering asymmetry between suitably defined hadronic and flavor specific (tagging) decays offers a promising method for determining the width difference. The corresponding time ordering-charge asymmetry can also bound the mixing phase. Similar observables involving exclusive decays are also considered. At the super B factories with O(50) times greater luminosity time ordering and time ordering-charge asymmetries between inclusive and exclusive modes may also provide additional bounds on the phases in those decays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Perceiving the coherent movements of spatially-separated features

When a partially-occluded object is represented in an image, it is defined by a set of spatially-separated features that may be registered at different spatial scales. To understand the image, human vision must organize these fragmented optical features into common and distinct object surfaces. Although the common fate of moving features often is considered a primary source of reliable information for image segmentation, little is known of the visual system's capacity to discriminate the coherent relative movements of spatially-separated features. In a series of experiments, observers viewed elements whose movements were correlated (direction and magnitude) or were uncorrelated. Our results indicate that observers can discriminate the two types of movement about as well as they can detect any movement at all. Moreover, the ability to perceive coherent movements is maintained under a variety of conditions including differences in the elements' spatial frequency content, spatial position and contrast, and temporal phase shifts between the spatially-correlated displacements. These results suggest that coherent relative motion may be a fundamental source of information exploited by vision, despite considerable variability in the spatial and temporal characteristics of the individual features.

Mowafy, Lyn↗

Parameter study of a Kinetic Phase Transition model

We investigate the ability of the two model parameters in the Kinetic Phase Transition (KPT) model of Carl Greeff to describe phase transitions of various types when combined with the tin Equation of states for the phases, SESAME 2162. While the two parameters are correlated, one combination can be associated with the nucleation process giving rise to the hysteresis seen in phase transition paths in pressure-temperature space and another can be associated with the overall timescale of the transition. We acknowledge the desire to have a model where the parameters are more independent of each other for easier model parameter determination.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical joint transform correlation on the DMD

Initial experimental investigation of the deformable mirror device (DMD) in a joint optical transform correlation is reported. The inverted cloverleaf version of the DMD, in which form the DMD is phase-mostly but of limited phase range, is used. Binarized joint Fourier transforms were calculated for similar and dissimilar objects and written onto the DMD. Inverse Fourier transform was done in a diffraction order for which the DMD shows phase-mostly modulation. Matched test objects produced sharp correlation, distinct objects did not. Further studies are warranted and they are outlined.

Knopp, Jerome↗

Spectroscopic fingerprints of gapless type-II fracton phases

Fracton phases feature elementary excitations with fractionalized mobility and are exciting interest from multiple areas of theoretical physics. However, the most exotic type-II fracton phases, like the Haah codes, currently have no known experimental diagnostics. Here, we explain how type-II fracton phases with gapless gauge modes, such as the U(1) Haah code, may be identified experimentally. Our analysis makes use of the multipole gauge theory description of type-II fracton phases, which exhibits ultraviolet-infrared (UV-IR) mixing. We show that neutron scattering experiments on gapless type-II fracton phases should generically exhibit exotic pinch points in the structure factor, with distinctive anisotropic contours as a direct consequence of UV-IR mixing. Furthermore, this characteristic pinch point structure provides a clean diagnostic of type-II fracton phases. We also identify distinctive signatures of the (3 + 1)-D U(1) Haah code in the low-temperature specific heat.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Benchmark of interfacial area concentration approaches for the two-fluid model in gas-dispersed condensing flow

Accurate predictions of interfacial area concentration (IAC) are required for closure of the condensation phase change term. The interfacial area transport equation (IATE) can dynamically predict interfacial area concentration and is increasingly being used in the benchmarking of phase change flows over static based correlations which require a flow regime map. For higher flow regimes, the two-group two-fluid IATE model can separately model the transport of spherical bubbles and cap/slug bubbles. Recently, a modified formulation of the one-group and two-group two-fluid model with interfacial area transport equation was proposed for gas-dispersed condensing flows. Three datasets have been used for validation consisting of condensing two-phase flow data in the unheated section of a vertical annulus with conditions spanning a range of pressures, inlet subcoolings and mass fluxes for benchmarking the various IAC approaches. For bubbly flows, the coupled void transport - IATE simulation results in good agreement in the predictions of the void fraction and the interfacial area concentration under nearly all sixty conditions. Considering the proposed two-group two-fluid IATE model formulation, the group-2 Nusselt number correlation is investigated to account for the appropriate heat transfer length scale for group-2 bubbles. Validation of the proposed two-group two-fluid model against the new dataset shows good agreement with experimental data with significant improvement over the one-group IATE model for conditions with substantial group-2 void fraction throughout the simulation domain.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Correlations of Pairs in Bichromatic Optical Lattices

Correlation functions of two interacting bosons in bound states confined in a quasi-periodic 1D optical lattice are investigated. This two-body problem is exactly solvable, and therefore, various correlation functions can be directly calculated. The first-order correlation and the resulting momentum distribution behave smoothly across the phase boundary and exhibit a strong dependence on the sign of on-site interactions. We demonstrate that this special signature of momentum distribution exists for both the extended phase and the localized phase. In addition to the dependence on the sign of on-site interactions, the second-order quantum coherence reveals complementary information about the quasi-periodic order of the system, the underling structure of the bound states and the characterization of the different phases of the bound states. We also study the second-order correlation in momentum space of the bound states in both the weak and strong coupling regimes and demonstrate different correlation patterns in these two regimes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sharp semiconductor-to-metal transition of VO{sub 2} thin films on glass substrates

Outstanding phase transition properties of vanadium dioxide (VO{sub 2}) thin films on amorphous glass were achieved and compared with the ones grown on c-cut sapphire and Si (111) substrates, all by pulsed laser deposition. The films on glass substrate exhibit a sharp semiconductor-to-metal transition (∼4.3 °C) at a near bulk transition temperature of ∼68.4 °C with an electrical resistance change as high as 3.2 × 10{sup 3} times. The excellent phase transition properties of the films on glass substrate are correlated with the large grain size and low defects density achieved. The phase transition properties of VO{sub 2} films on c-cut sapphire and Si (111) substrates were found to be limited by the high defect density.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quantum materials for energy-efficient neuromorphic computing: Opportunities and challenges

Neuromorphic computing approaches become increasingly important as we address future needs for efficiently processing massive amounts of data. The unique attributes of quantum materials can help address these needs by enabling new energy-efficient device concepts that implement neuromorphic ideas at the hardware level. In particular, strong correlations give rise to highly non-linear responses, such as conductive phase transitions that can be harnessed for short- and long-term plasticity. Similarly, magnetization dynamics are strongly non-linear and can be utilized for data classification. This Perspective discusses select examples of these approaches and provides an outlook on the current opportunities and challenges for assembling quantum-material-based devices for neuromorphic functionalities into larger emergent complex network systems.

36 MATERIALS SCIENCE↗

Identification and measurement of combustion noise from a turbofan engine using correlation and coherence techniques

Fluctuating pressure measurements within the combustor and tailpipe of a turbofan engine are made simultaneously with far field acoustic measurements. The pressure measurements within the engine are accomplished with cooled semi-infinite waveguide probes utilizing conventional condenser microphones as the transducers. The measurements are taken over a broad range of engine operating conditions and for 16 far field microphone positions between 10 deg and 160 deg relative to the engine inlet axis. Correlation and coherence techniques are used to determine the relative phase and amplitude relationships between the internal pressures and far field acoustic pressures. The results indicate that the combustor is a low frequency source region for acoustic propagation through the tailpipe and out to the far field. Specifically, it is found that the relation between source pressure and the resulting sound pressure involves a 180 deg phase shift. The latter result is obtained by Fourier transforming the cross correlation function between the source pressure and acoustic pressure after removing the propagation delay time. Further, it is found that the transfer function between the source pressure and acoustic pressure has a magnitude approximately proportional to frequency squared. These results are shown to be consistent with a model using a modified source term in Lighthill's turbulence stress tensor, wherein the fluctuating Reynolds stresses are replaced with the pressure fluctuations due to fluctuating entropy.

Karchmer, A. M.↗

Integrated Analyses of Multiple Worldwide Aerosol Mass Spectrometer Datasets for Improved Understanding of Aerosol Sources and Processes and for Comparison with Global Models

The AMS is the only current instrument that provides real-time, quantitative, and size-resolved data on submicron non-refractory aerosol species with a time resolution of a few minutes or better. The AMS field data are multidimensional and massive, containing extremely rich information on aerosol chemistry, microphysics and dynamics—basic information that is required to evaluate and quantify the radiative climate forcing of atmospheric aerosols. The high time resolution of the AMS data also reveals details of aerosol dynamic variations that are vital to understanding the physico-chemical processes of atmospheric aerosols that govern aerosol properties relevant to the climate. There are two primary objectives of this 3-year project. Our first objective is to perform highly integrated analysis of dozens of AMS datasets acquired from various urban, forested, coastal, marine, mountain peak, and rural/remote locations around the world and synthesize and inter-compare results with a focus on the sources and the physico-chemical processes that govern aerosol properties relevant to aerosol climate forcing. Our second objective is to support our collaboration with global aerosol modelers, in which we will supply the size-resolved aerosol composition and temporal variation data (via a public web interface) and our analysis results for use in model testing and validation and for translation of the rich AMS database into model constraints that can improve climate forcing simulations. Several prominent global aerosol modelers have expressed enthusiastic support for this collaboration. The specific tasks that we propose to accomplish include 1) to develop, validate, and apply multivariate analysis techniques for improved characterization and source apportionment of organic aerosols; 2) to evaluate aerosol source regions and relative contributions based on back-trajectory integration (PSCF method); 3) to summarize and synthesize submicron aerosol information, including composition, concentration, size distribution and (inferred) shape and mixing state in various environments and their regional and seasonal variations within the context of regional and global modeling; and 4) to quantitatively evaluate important processes in various atmospheric environments and during different seasons, focusing on acid-catalyzed SOA formation, new particle growth, and photochemical processes of atmospheric organic aerosols (i.e., SOA production and POA oxidation). We will also examine the correlations and compile the ratios between important pairs of aerosol and gas phase species using region-specific and season-specific correlations and as a function of photochemical age and compare them with the ratios produced by various models. To enable our collaborations with the modelers, we will supply (via a public web interface) AMS data and our analysis results for use in model testing and validation and facilitate the use of the AMS information to constrain calculations of radiative forcing. Model output and AMS measurements and derived parameters will be compared with a focus on regional variability of model/measurement discrepancies and their causes. Finally we will share results, insights and data mining algorithms through peer-reviewed publications, presentations/tutorials at conferences/workshops, and web dissemination of analysis results and in-house developed software packages.

58 GEOSCIENCES↗

A laser ultrasonics-based approach for rapid screening of high entropy alloys

This project demonstrates a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique is used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that laser ultrasonics-based methodology developed in this work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗