Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phased Array”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Comparison of Atmospheric Delay Statistics from Deep Space Network Arrays and Nearby Test Interferometers

Several techniques have been explored and demonstrated that allow for greater data return on space-to-ground links. Among these techniques, arraying several smaller diameter dish antennas together is one method used in several arenas. These arrays can achieve larger effective area and gain than are available from a single larger antenna. This technique is routinely used by the NASA Deep Space Network (DSN) at 8.4 GHz where the incoming signals are much weaker than those experienced by the near-Earth satellite community. When considering arraying at much higher frequencies such as 32 GHz deep-space Ka-band, the phase alignment of the individual antenna signals is significantly disrupted by atmospheric turbulence. Since 2012, several downlink array demonstrations have been conducted using 32 GHz carrier signals emitted by the deep space probes Cassini and Kepler. Site test interferometers (STIs) that receive signals from geostationary satellites have been deployed at all three DSN tracking complexes for long-term monitoring of atmospheric delay fluctuations. In a previous DSN array demonstration study involving the Cassini spacecraft, it was shown that statistics of the adjusted STI phase fluctuations matched the statistics of concurrent array demonstration phase fluctuations. These adjustments accounted for differences in antenna separation, elevation angle and spacecraft frequencies. The STI antenna separations were about 200 m and the DSN antenna separations were about 300 m. These adjustments made use of the thick-layer turbulence model that was applicable to the Goldstone desert climate during the summer months for which the data were acquired. In this paper, we report on the results of additional array demonstrations involving the Kepler spacecraft and compare the adjusted STI phase fluctuations with those seen by a nearby two-element array of 34 m diameter antennas tracking Kepler’s 32 GHz signal at the Goldstone, California and Madrid, Spain DSN sites. We also discuss results from a demonstration using an array over a longer 12.5 km baseline. The Cassini and Kepler array demonstrations were found to validate the long term statistics acquired from several years of STI data as well as the models used to adjust the statistics for the conditions of an array. These statistics represent reliable estimates of the phase fluctuations that would be seen by an array tracking a deep space signal after applying appropriate adjustments for a given array configuration, elevation angle profile and observing frequency.

Morabito, David D.↗

Experimental and analytical study of the hydrodynamic and single and two-phase convective heat transfer performance of flexible PDMS microchannels with micropillar arrays

Various copper and silicon based thermal management systems are used in the cooling of electronics. However, the rigid nature of these materials along with their high thermal and electrical conductivity pose a difficulty in developing direct contact embedded flexible cooling systems that can offer robust cooling performance. The low density, thermal stability, chemical inertness, and electrical insulation of Polydimethylsiloxane (PDMS) make it an ideal material to develop lightweight direct contact thermal management systems for electronics. Its ease of fabrication with tunable flexibility provides the opportunity to go beyond traditional electronics and develop advanced active and passive thermal management systems for a wide–range of applications in foldable and wearable electronics, liquid cooling garments, microgravity, and electric motors. In this study, a flexible PDMS based microchannel with micropillar arrays, which enhance the thermal performance of the device through capillary-assisted flow, has been developed. The hydrodynamic and convection heat transfer performance of three PDMS wick pillar geometries, ranging from a porosity of 0.8–0.91, are investigated and compared under single-phase and two-phase conditions. Dielectric coolant FC-3283 is employed and permeability measurements are made for mass fluxes ranging from 53 kg/m 2 s to 369 kg/m 2 s. Given its conformability, the device demonstrates a deviation from Darcy’s Law, within the laminar regime, with an increasing permeability with mass flux at the rate of ~0.5–0.8 Darcy/(kg/m 2 s). A semi-analytical model has been developed and reported to quantify the conformability of the device. The heat transfer performance is experimentally evaluated using the same dielectric fluid for mass flux ranging from 105 kg/m 2 s to 420 kg/m 2 s with heat fluxes ranging from 1.5 W/cm 2 to 16 W/cm 2 . Heat transfer coefficients of up to 7000 W/m 2 K are observed, which are comparable to copper and silicon microchannels. The effect of porosity on the single phase thermal performance has been evaluated against the pumping power to provide a basis for thermal management system design. Finally, high-speed imaging is performed to study the two-phase flow characteristics to provide insight into the vapor formation and removal.

42 ENGINEERING↗

Commissioning and first results of the reinstated JET ICRF ILA

The JET ICRF ITER-like Antenna (ILA) has been operated at 33, 42 and 47 MHz in 2008–2009 but stopped operation in 2009 due to the failure of one of the tuning capacitors inside the antenna. Tests on a spare capacitor showed that a micro-leak was caused by the cycle wear of a capacitor’s internal bellows. The ILA was reinstated with a new operating scheme minimizing the full stroke requests of the capacitor. This contribution gives an overview of the works undertaken to reinstate the JET ILA up to the first results on plasma. The capacitors were replaced and high voltage tests of the capacitors were performed. An extensive calibration of all the measurements in the RF circuit was carried out. New simulation tools were created and control algorithms were implemented for the – toroidal and poloidal – phase control of the array as well as for the matching of the second stage. New protections are being implemented for the thermal and voltage protection of the capacitors. Low voltage matching tests were performed before the high power commissioning. Finally the first results on plasma are presented, showing that the new controls allow extending the range of the operation to lower (29 MHz) and higher (51 MHz) frequencies than previously achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reinstated JET ICRF ILA: Overview and Results

The works undertaken to reinstate the JET ICRF ILA are reviewed. The vacuum matching capacitors were replaced, an extensive calibration of all the measurements in the RF circuit was carried out, new simulation tools were created and new control algorithms were implemented for the – toroidal and poloidal – phase control of the array as well as for the matching of the second stage. A review of the contribution of the reinstated ILA to the JET programme during the last campaigns is given showing namely that the new controls allowed extending the range of the operation to lower (29MHz) and higher (51MHz) frequencies than previously achieved and allowed more flexible and reliable operation. Operation with coupled power levels up to 2.8MW and voltages up to 40kV was achieved. ILA results on plasma are discussed and emphasis is given to the features of interest for ITER.

Dumortier, Pierre↗

Preliminary measurements of the edge magnetic field pitch from 2-D Doppler backscattering in MAST and NSTX-U (invited)

The Synthetic Aperture Microwave Imaging (SAMI) system is a novel diagnostic consisting of an array of 8 independently phased antennas. At any one time, SAMI operates at one of the 16 frequencies in the range 10-34.5 GHz. The imaging beam is steered in software post-shot to create a picture of the entire emission surface. In SAMI’s active probing mode of operation, the plasma edge is illuminated with a monochromatic source and SAMI reconstructs an image of the Doppler back-scattered (DBS) signal. By assuming that density fluctuations are extended along magnetic field lines, and knowing that the strongest back-scattered signals are directed perpendicular to the density fluctuations, SAMI’s 2-D DBS imaging capability can be used to measure the pitch of the edge magnetic field. In this paper, we present preliminary pitch angle measurements obtained by SAMI on the Mega Amp Spherical Tokamak (MAST) at Culham Centre for Fusion Energy and on the National Spherical Torus Experiment Upgrade at Princeton Plasma Physics Laboratory. Lastly, the results demonstrate encouraging agreement between SAMI and other independent measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

PREDICTIONS FOR ULTRA-DEEP RADIO COUNTS OF STAR-FORMING GALAXIES

We have worked outty predictions for the radio counts of star-forming galaxies down to nJy levels, along with redshift distributions down to the detection limits of the phase 1 Square Kilometer Array MID telescope (SKA1-MID) and of its precursors. Such predictions were obtained by coupling epoch-dependent star formation rate (SFR) functions with relations between SFR and radio (synchrotron and free–free) emission. The SFR functions were derived taking into account both the dust-obscured and the unobscured star formation, by combining far-infrared, ultraviolet, and Hα luminosity functions up to high redshifts. We have also revisited the South Pole Telescope counts of dusty galaxies at 95 GHz, performing a detailed analysis of the Spectral Energy Distributions. Our results show that the deepest SKA1-MID surveys will detect high-z galaxies with SFRs two orders of magnitude lower compared to Herschel surveys. The highest redshift tails of the distributions at the detection limits of planned SKA1-MID surveys comprise a substantial fraction of strongly lensed galaxies. We predict that a survey down to 0.25 μJy at 1.4 GHz will detect about 1200 strongly lensed galaxies per square degree, at redshifts of up to 10. For about 30% of them the SKA1-MID will detect at least 2 images. The SKA1-MID will thus provide a comprehensive view of the star formation history throughout the re-ionization epoch, unaffected by dust extinction. We have also provided specific predictions for the EMU/ASKAP and MIGHTEE/MeerKAT surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

Spatial and temporal evaluations of the liquid argon purity in ProtoDUNE-SP

Liquid argon time projection chambers (LArTPCs) rely on highly pure argon to ensure that ionization electrons produced by charged particles reach readout arrays. ProtoDUNE Single-Phase (ProtoDUNE-SP) was an approximately 700-ton liquid argon detector intended to prototype the Deep Underground Neutrino Experiment (DUNE) Far Detector Horizontal Drift module. It contains two drift volumes bisected by the cathode plane assembly, which is biased to create an almost uniform electric field in both volumes. The DUNE Far Detector modules must have robust cryogenic systems capable of filtering argon and supplying the TPC with clean liquid. This paper will explore comparisons of the argon purity measured by the purity monitors with those measured using muons in the TPC from October 2018 to November 2018. A new method is introduced to measure the liquid argon purity in the TPC using muons crossing both drift volumes of ProtoDUNE-SP. For extended periods on the timescale of weeks, the drift electron lifetime was measured to be above 30 ms using both systems. A particular focus will be placed on the measured purity of argon as a function of position in the detector.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Complex transport and magnetism in inhomogeneous mixed valence Ce 3 Ir 4 Ge 13

We report the discovery of Ce 3 Ir 4 Ge 13 , a Remeika phase with a complex array of structural, electronic, and magnetic properties. In this work, our single crystal x-ray diffraction measurements show that Ce 3 Ir 4 Ge 13 forms in the tetragonally distorted $I4_1/amd$ space group, which has three distinct rare earth sites. The electrical resistivity is almost temperature independent over three decades in temperature, from 0.4 K to 400 K, while the Hall coefficient measurements are consistent with a low-carrier semimetal. Magnetic susceptibility measurements reveal an effective moment, $μ^\text{exp}_\text{eff} = 1.87μ_B/$Ce, that falls significantly short of the expected value for Ce 3+ , suggesting that two of the rare earth sites are occupied by magnetic Ce 3+ while the third is occupied by nonmagnetic Ce 4+ . Upon cooling, Ce 3 Ir 4 Ge 13 first enters a short range magnetically ordered state below $T_\text{SRO}$ = 10 K, marked by a deviation from Curie-Weiss behavior in susceptibility and a broad field-independent heat capacity anomaly. At lower temperatures, we observe a second, sharper peak in the heat capacity at $T^\ast$ = 1.7 K, concurrent with a splitting of the field-cooled and zero-field-cooled susceptibilities. A small resistivity drop at $T^\ast$ suggests a loss of spin disorder scattering consistent with a magnetic ordering or spin freezing transition. Ce 3 Ir 4 Ge 13 is therefore a rare example of an inhomogeneous mixed valence compound with a complex array of thermodynamic and transport properties.

36 MATERIALS SCIENCE↗

Large active retrodirective arrays for solar power satellites

An active retrodirective array (ARA) transmits a beam toward the apparent source of an illuminating signal called the pilot. The array produces the RF power. Retrodirectivity is achieved by retransmitting from each element of the array a signal whose phase is the 'conjugate' of that received by the element. Application of the ARA to the solar power satellite concept has been proposed. A method of providing a reference phase is described, called 'central phasing', which eliminates the need for a rigid structure ordinarily needed in order to realize accurate retrodirectivity.

Chernoff, R.↗

Wide angle Michelson Doppler imaging interferometer

The optical system, stepping control, phase and modulation depth, array detector, and directions sensor are described for a specialized type of Michelson interferometer which works at sufficiently high resolution to measure the line widths and Doppler shifts of naturally occurring atmospheric emissions. With its imaging capability, the instrument can potentially supply this data independently for each element of the 100 x 100 detector array. The experiment seeks: (1) to obtain vertical profiles of atmospheric winds and temperatures as functions of latitude by observing near the limb; (2) to acquire exploratory wind and temperature data on smaller scale structures in airglow irregularities and in auroral forms; and (3) to collaborate with other Spacelab experiments, such as barium cloud releases, in providing wind and temperature data.

Shepherd, G. G.↗

Active retrodirective arrays for SPS beam pointing

The basic requirement of the SPS beam pointing system is that it deliver a certain amount of S-band (lambda = 12.5 cm) power to a 9.6 km diameter receiving rectenna on the ground. The power is transmitted from a 1.0 km diameter antenna array on the SPS, which is, for a rectenna at about plus or minus 40 deg. latitude, some 37.5x10 to the 6th power km distant. At the present time ARA's appear to be the best bet to realize this very stringent beam pointing requirement. An active retrodirective array (ARA) transmits a beam towards the apparent source of an illuminating signal called the pilot. The array produces, not merely reflects, RF power. Retrodirectivity is achieved by retransmitting from each element of the array a signal whose phase is the "conjugate" of that received by the element. Phase conjugate circuits and pointing errors in ARA's are described. Results obtained using a 2-element X-band ARA and an 8-element S-band ARA are included.

Chernoff, R.↗

Conceptual design of a coherent optical system of modular imaging collectors (COSMIC)

The Coherent Optical System of Modular Imaging Collectors (COSMIC) is the design concept for a phase-coherent optical telescope array that may be placed in earth orbit by the Space Shuttle in the 1990s. The initial system module is a minimum redundancy array whose photon collecting area is three times larger than that of the Space Telescope, and possesses a one-dimensional resoution of better than 0.01 arcsec in the visible range. Thermal structural requirements are assessed. Although the coherent beam combination requirements will be met by an active control system, the COSMIC structural/thermal design must meet more stringent performance criteria than even those of the Space Telescope.

Nein, M. E.↗

Phase sensitive guidance sensor for wire-following vehicles

A guidance sensor for a wire-following vehicle which is phase sensitive, includes an array of coils positioned to sense the vertical component of a magnetic field produced by the ac current through the guidance wire. The outputs of the coils are fed to associated flip flops. Flip flops associated with coils, through which flux passes in one direction, e.g., up, are driven to one state, e.g., true, and flip flops associated with coils through which flux passes in the opposite direction, e.g., down, are driven to a false state. The control signal to guide the vehicle over the wire is a function of the number of flip flops in the true state. Circuitry is included to prevent flip flops from assuming a wrong state due to noise.

Hansen, G. R.↗

On broadband shock associated noise of supersonic jets

The characteristics and generation mechanisms of noise associated with the interactions of turbulence with the quasi-periodic broadband shock cells of supersonic jet engines are reviewed. The noise possesses broadband spectra and directionality that are completely different from noise caused by turbulence. Experimental data have shown that broadband noise is most prominent in the forward arc, with peak frequencies being a function of the observation angle and the pressure mismatch in the engine. The noise originates in the engine as turbulence-shock interactions occur during downstream movement. Features of the phased point-source array model and the large turbulence structures-shock cells interaction model are defined and model predictions are compared with experimental data on noise sources. Only a scaling of the noise component is found to be currently possible. More complete characterization depends on consideration of the jet temperature and analysis of turbulence-shock interactions, broadband shock and screech tones and shock noise in several flow configurations.

Tam, C. K. W.↗