Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reference Model 2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Slugging Flow of Water Draining from the Bottom of a Non-Vented Container

Experiments were run to observe the behavior of water exiting through an orifice at the bottom of an non-vented container. Initially, the container is nearly full of water with a small air space on top. Once the orifice was uncovered, the slugging rate and the drain rate of the water leaving the container were measured. Upon initially opening the orifice, water drains out until the air pressure above the water reduces enough that the air pressure drop from inside to outside of the container supports the water column and the water stops flowing. Air then enters the container through the orifice forming a bubble, which grows until it detaches and bubbles through the water to reach the air space. Once the bubble enters, this added air increases the pressure in the air space enough to allow the water to start flowing out again. This cycle of flow out, flow stoppage, air inflow, and bubble breakoff continues over and over until the hole is closed or the container empties. This is referred to as the “slugging cycle.” A mechanism is proposed to describe the slugging cycle which is modeled analytically. This paper presents the description of the experiments, data obtained, the mechanistic model, and comparison of the model to the experimental data. The model predicts outflow rates close to experimental values. Flow rates from non-vented containers are more than 10 to 20 less than vented containers. The bubbles which must enter the container periodically to increase the internal air pressure stop the water flow momentarily so are responsible for this large decrease in flow rate. Swirl induced in the non-vented container causes the flow rates to increase by a factor of two. The flow rate out of a non-vented container is independent of water height which is in direct contrast to a vented container where the flow rate is proportional to the square root of the water height. The constant rate is due to the container pressure. The higher the water level, the lower the air pressure is in the container. This analytical model requires input of the bubble size. The volume recommended is the volume of a cylinder with the base of the orifice area and length of 3.3 cm. Slugging rate varies only a small amount falling in the range to 2 to 4 cycles/sec. Preliminary work with other containers indicates larger containers, larger orifices and nozzle exit shapes produce higher specific flow rates. The standard multiphase flow equations could not be used to analyze this situation because the two phases are not interpenetrating. Instead one phase must fully stop before the other can flow. Interpenetrating phases allow can pass one another each affecting the other with friction and virtual mass. An interesting observation: The negative air pressure in the container is observable. It equals the water height.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Survey of U.S. Research Reactor Auxiliary Facilities Used for Material Testing and Basic Neutron Science

A catalogue of and attributes of the Materials Irradiation and Testing facilities (MIF) and the Basic Neutron Science facilities (BSF) of auxiliary (AUX) facilities of research reactors are compiled. The survey of these facilities is drawn from the set of U.S. university and DOE research reactor facilities and should be considered as a reference point when comparing commonalities in international AUX facilities. The size and shielding capabilities of the facilities, the typical characterization equipment used, and the neutron flux and irradiation capabilities of the facilities are listed. Short descriptions of experimental activities and current practices are detailed for MIFs and BSFs. The attributes are important in consideration of the reconfiguration of the facilities for purposes other than stated mission, i.e., for proliferation of weapons-usable nuclear material (WUNM). An evaluation of the capacity for production rate of WUNM from neutron beams-on-targets or a sample that has been placed in an irradiation position for a period is provided. Further evaluation of reconfiguration of these MIF and BSF are recommended to refine the proliferation risks. Specifically, MIF hot cells and potential configurations, additional modeling of facility throughput and development of methods for determining levels of concern for MIF and BSF have all been identified as steps for refinement of determination of the risks associated with these facilities. Future work will focus on: 1. A model of projected throughput for different MIF and BSF configurations that will be used to provide a window of potential operational misuse for a facility and better understand the capability of production and the rate of processing for WUNM in these facilities. 2. A misuse study for various configurations of MIF hot cell layouts detailing capacity, specifications, shielding constraints for MIF operations, identification of a maximum shielding thickness, and reasonable need associated with each activity performed in a MIF. 3. Development of a rule of thumb rating system utilizing data gathered from previous reports to show levels of concern at a given power level, flux, and experiment set.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

ARM data-oriented metrics and diagnostics package for climate model evaluation (ARM-DIAGS-V3) version 3

A Python-based metrics and diagnostics package is currently being developed by the ARM Infrastructure Team at Lawrence Livermore National Laboratory to facilitate the use of long-term high frequency measurements from the ARM program in evaluating the regional climate simulation of clouds, radiation, precipitation, and aerosols. This metrics and diagnostics package computes climatological means of targeted climate model simulation and generates tables and plots for comparing the model simulation with ARM observational data. The CMIP model data sets are also included in the package to enable model inter-comparison as demonstrated in Zhang et al. (2018) and Zhang et al. (2020). The mean of the CMIP model can be served as a reference for individual models. Basic performance metrics are computed to measure the accuracy of mean state and variability of climate models. The evaluated physical quantities include cloud fraction, temperature, relative humidity, cloud liquid water path, total column water vapor, precipitation, sensible and latent heat fluxes, aerosol optical depth, and radiative fluxes, with plan to extend to more fields, such as the evaluation of model simulated aerosol physicochemical properties and cloud microphysics properties. Process-oriented diagnostics focusing on aerosol, cloud, and precipitation-related phenomena are also being developed for the evaluation and development of specific model physical parameterizations. In addition to the Southern Great Plains (SGP), North Slope of Alaska (NSA) and Tropical Western Pacific (TWP) atmospheric observatories in the ARMDIAGS version 2.0, the version 3.0 package have extended to the data collected at the ARM Eastern North Atlantic (ENA) atmospheric observatory and the Observation and Modeling of the Green Ocean Amazon (GOAMAZON) field campaign. The metrics and diagnostics package are currently built upon standard Python libraries and additional Python packages developed by DOE (CDAT). The ARM metrics and diagnostic package is available publicly with the hope that it can serve as an easy entry point for climate modelers to compare their models with ARM data. In this report, we first provide an overview of major metrics in section 2. The input data, which constitutes the core content of the metrics and diagnostics package, is summarized in section 3. A user's guide documenting the workflow/structure of the version 3.0 codes and including step-by-step instruction for running the package is described in section 4.

54 ENVIRONMENTAL SCIENCES↗

Full spectrum (350-2500 nm) canopy spectral reflectance, Seward Peninsula, Alaska, 2018

Full-range (350-2500 nm) canopy reflectance spectra of various Arctic tundra ecosystem endmembers, including canopy-scale species endmember spectra, plot-scale spectra, and transect spectra as well as non-vegetated surface (NVS) spectra. The datasets were collected at the three core NGEE-Arctic watersheds, Kougarok, Teller, and Council, as well as the supplemental Kougarok Mile 80 site within the larger Seward Peninsula, Alaska region. The data were collected in July 2018 using a full-range Spectra Vista Corporation (SVC) HR-1024i spectroradiometer. Canopy-scale reflectance was collected with an 8-degree field-of-view (FOV) foreoptic lens. All spectral measurements were collected as calibrated surface radiance and converted to surface reflectance using a 99.99% reflective Spectralon white reference standard. For those canopy spectra collected with associated functional trait data, the FOV of the instrument was positioned to include the same leaves harvested for functional trait measurements, including leaf mass per area (LMA) and foliar carbon and nitrogen content (see associated dataset). Species included in the spectra and functional trait dataset include Alnus viridis, Betula nana, Betula glandulosa, Arctous alpina, and Salix pulchra. This data package includes 35 files in a variety of formats including processed canopy spectra (*.csv), processed dGPS locations (*.csv and *.kmz), digital photographs of spectral targets (*.jpg) and raw data from spectroradiometer and dGPS instruments (compressed as tar.gz). Metadata files include data descriptions (_dd.csv) for tabular data and a key to species symbols used in data files. All included files are listed and described in NGA208_flmd.csv.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

Annual Report: Carbon Capture Simulation Initiative (CCSI) (30 September 2013)

The Carbon Capture Simulation Initiative (CCSI) is a partnership among national laboratories, industry and academic institutions that is developing and deploying state-of-the-art computational modeling and simulation tools to accelerate the commercialization of carbon capture technologies from discovery to development, demonstration, and ultimately the widespread deployment to hundreds of power plants. The CCSI Toolset will provide end users in industry with a comprehensive, integrated suite of scientifically validated models, with uncertainty quantification (UQ), optimization, risk analysis and decision making capabilities. The CCSI Toolset incorporates commercial and open-source software currently in use by industry and is also developing new software tools as necessary to fill technology gaps identified during execution of the project. Ultimately, the CCSI Toolset will (1) enable promising concepts to be more quickly identified through rapid computational screening of devices and processes; (2) reduce the time to design and troubleshoot new devices and processes; (3) quantify the technical risk in taking technology from laboratory-scale to commercial-scale; and (4) stabilize deployment costs more quickly by replacing some of the physical operational tests with virtual power plant simulations. CCSI is led by the National Energy Technology Laboratory (NETL) and leverages the Department of Energy (DOE) national laboratories’ core strengths in modeling and simulation, bringing together the best capabilities at NETL, Los Alamos National Laboratory (LANL), Lawrence Berkeley National Laboratory (LBNL), Lawrence Livermore National Laboratory (LLNL), and Pacific Northwest National Laboratory (PNNL). The CCSI’s industrial partners provide representation from the power generation industry, equipment manufacturers, technology providers and engineering and construction firms. The CCSI’s academic participants (Carnegie Mellon University, Princeton University, West Virginia University, Boston University and the University of Texas at Austin) bring unparalleled expertise in multiphase flow reactors, combustion, process synthesis and optimization, planning and scheduling, and process control techniques for energy processes. During Fiscal Year (FY) 13, CCSI announced the initial release of its first set of computational tools and models during the October 2012 meeting of its Industry Advisory Board. This initial release led to five companies licensing the CCSI Toolset under a Test and Evaluation Agreement this year. By the end of FY13, the CCSI Technical Team had completed development of an updated suite of computational tools and models. The list below summarizes the new and enhanced toolset components that were released following comprehensive testing during October 2013. 1. FOQUS. Framework for Optimization and Quantification of Uncertainty and Sensitivity. Package includes: FOQUS Graphic User Interface (GUI), simulation-based optimization engine, Turbine Client, and heat integration capabilities. There is also an updated simulation interface and new configuration GUI for connecting Aspen Plus or Aspen Custom Modeler (ACM) simulations to FOQUS and the Turbine Science Gateway. 2. A new MFIX-based Computational Fluid Dynamics (CFD) model to predict particle attrition. 3. A new dynamic reduced model (RM) builder, which generates computationally efficient RMs of the behavior of a dynamic system. 4. A completely re-written version of the algebraic surrogate model builder for optimization (ALAMO). The new version is several orders of magnitude faster than the initial release and eliminates the MATLAB dependency. 5. A new suite of high resolution filtered models for the hydrodynamics associated with horizontal cylindrical objects in a flow path. 6. The new Turbine Science Gateway (Cluster), which supports FOQUS for running multiple simulations for optimization or UQ using a local computer or cluster. 7. A new statistical tool (BSS-ANOVA-UQ) for calibration and validation of CFD models. 8. A new basic data submodel in Aspen Plus format for a representative high viscosity capture solvent, 2-MPZ system. 9. An updated RM tool for CFD (REVEAL) that can create a RM from MFIX. A new lightweight, stand-alone version will be available in late 2013. 10. An updated RM integration tool to convert the RM from REVEAL into a CAPE-OPEN or ACM model for use in a process simulator. 11. An updated suite of unified steady-state and dynamic process models for solid sorbent carbon capture included bubbling fluidized bed and moving bed reactors. 12. An updated and unified set of compressor models including steady-state design point model and dynamic model with surge detection. 13. A new framework for the synthesis and optimization of coal oxycombustion power plants using advanced optimization algorithms. This release focuses on modeling and optimization of a cryogenic air separation unit (ASU). 14. A new technical risk model in spreadsheet format. 15. An updated version of the sorbent kinetic/equilibrium model for parameter estimation for the 1st generation sorbent model. 16. An updated process synthesis superstructure model to determine optimal process configurations utilizing surrogate models from ALAMO for adsorption and regeneration in a solid sorbent process. 17. Validation models for NETL Carbon Capture Unit utilizing sorbent AX. Additional validation models will be available for sorbent 32D in 2014. 18. An updated hollow fiber membrane model and system example for carbon capture. 19. An updated reference power plant model in Thermoflex that includes additional steam extraction and reinjection points to enable heat integration module. 20. An updated financial risk model in spreadsheet format.

01 COAL, LIGNITE, AND PEAT↗

I. Final Report for DOE SBIR Phase I Project DE-SC0013795 Final Report for DOE SBIR Phase I Project DE-SC0013795 Microtron-based Compact, Portable Gamma-Ray Source

Microtron-based Compact, Portable Gamma-Ray Source. The objective of Phase I of this project was to produce a conceptual design of a prototype compact microtron electron accelerator, which could be designed, built, and demonstrated in Phase II of the project. The conceptual design study included an analysis of the parameters of the microtron and its components, and the expected performance of the prototype microtron as a source of x-rays and/or RF neutrons in the MeV energy range. The major components of the microtron are the magnet, the accelerating system, the power system, the vacuum system, the control system, the beam extraction system and the targets to produce x-rays (and/or neutrons). Our objectives for the design of the prototype were for it to be compact, cost-effective, capable of producing high intensity x-ray (an/or neutron) fluxes. In addition, the prototype was to be easily assembled and disassembled so that components could be easily replaced. The main parameters for the prototype are the following: the range of electron kinetic energies, the output power, the RF frequency band (X-band, C-band, or S-Band), the type of injection (Type I or Type II), the magnet type, i.e. permanent magnet, electromagnet, or a hybrid combination of permanent and electromagnet. The results of the Phase I study and analysis for a prototype microtron are the following: The electron energy range can be varied from below 6 MeV to 9 MeV, the optimal frequency range is S-Band (2-4 GHz) RF frequency, Type II injection (described below), and the magnet type is the hybrid version. The prototype version will be capable of producing gamma ray doses of ~1800 R/min-m and neutron fluxes of up to ~6 x 10 10 n/s with appropriate targets. The results of the Phase I study and analysis are provided below. The proposed Phase II plan was to demonstrate the prototype at low beam power. In the subsequent Phase III, high power tests would be performed, and the design of commercial versions of microtrons with various energies, sizes and types would be produced and marketed, including a more compact and more portable 6 MeV battery-powered model that more closely meets the requirements in the original FOA topic description. In the course of the Phase I study, we also identified another microtron version, one that was larger (not compact) and more powerful than that of the Phase II prototype, which could serve as an intense source of photo- neutrons, up to 4 x 10 12 n/s for use in nuclear medicine, short-lived isotope production, or other applications. In addition, it could produce gamma dose rates up to 130 kR/min-m with a heavy metal bremsstrahlung target. The results and specifications of this were submitted to IPAC16 (Reference [12]) the paper is included in Addendum B. Because this version was beyond the scope of the Phase I project, there is no additional description in the Final Report.

43 PARTICLE ACCELERATORS↗

Thermal Integration of Advanced Nuclear Reactors with a Reference Refinery, Methanol Synthesis, and a Wood Pulp Plant (Rev.1)

The present report is intended to provide process flow diagrams (PFDs) and energy and mass balance data sheets for a U.S. industrial sector subset with which nuclear heat and power could be integrated—a subset that includes the oil refining, methanol and pulp and paper industries. Coupling options for integrating nuclear energy into these industries are quantitatively outlined for reference systems, and future work will extend this analysis in greater detail. Opportunities for integrating small modular nuclear reactors (SMNRs) were investigated for each of the industrial process configurations. Aspen HYSYS and Cycle-Tempo models for a high-temperature gas-cooled reactor were developed to evaluate the proposed integration. This introductory evaluation provides a general description and assessment of the operating principles, reactor coolant core outlet temperature, and reactor size to be integrated with industry. The industrial processes of oil refining and the production of methanol, pulp and paper were simulated by using Aspen HYSYS, Aspen Plus, and the PRELIM (Petroleum Refinery Life Cycle Inventory Model) tool to develop process details. Cycle-Tempo models then extend the process modeling results to obtain net energy demands (e.g., heat, steam, and electricity) when accounting for process steam and waste heat recovery. This information is intended to foster the analysis of integrating an SMNR to decarbonize industrial facilities. The SMNR would provide reliable, competitive, and sustainable clean energy while reducing carbon emissions and other environmental impacts, such as water withdrawals, consumption, and contamination. The refining industry, exhibited in Figure ES1, is a leading consumer of fossil -fuel-based heat, power, and hydrogen in the U.S. industrial sector, generating over 164 million metric tons (MMT) of CO 2 emissions in 2023. The overall mass and energy pertaining to a generalized complex refinery in the United States is reflected in Figure ES1, along with energy metrics regarding integration with a nuclear power plant (NPP). Data sheets were developed to indicate the energy requirements for the overall refinery and each refinery process. The data sheet for the overall refinery is shown in Table ES2.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Equity-Centered Engagement Through Climate Resilience Policy in Massachusetts

Communities who experience disproportionate climate change impacts tend to be excluded from resilience planning (Vale, 2014). Those efforts typically follow top-down processes within established governance practices that are inaccessible to marginalized folks and reinforce inequalities (Malloy & Ashcraft, 2020; Adger, 2003). Such participatory planning processes may offer the public little opportunity to influence the process itself or the outcomes (Smith & McDonough, 2001). They might ignore important public values or alternative ways of knowing which can be critical assets in resilience (Few et al., 2007). Designing communities for climate action and resilience means creating opportunities for everyone to meaningfully shape those decisions and experience related benefits. Having the opportunity to shape one’s community is necessary for human flourishing (Allen, 2016). Resilience planning that shifts power into communities and focuses on social vulnerability can affect how people survive and thrive in a climate changed world. The Massachusetts Municipal Vulnerability Preparedness (MVP) 2.0 program is an attempt to change the status quo in resilience planning by bringing new voices into decision-making power, recognizing their labor, addressing root causes of vulnerability, and investing in social infrastructure. It aspires to build capacity for equity-focused community engagement within teams of municipal staff and community liaisons, and ultimately build social capital and community cohesion. My mixed methods research investigates implementation of this state grant program in several western Massachusetts towns. I am using document review, participant observation, and interviews to understand the MVP 2.0 process as written, how different towns navigate it, and how individuals make sense of their experiences in it. I seek to understand how those experiences explain relationships between engagement approaches, mediating factors, and process outcomes. I am interested in the conditions that allow for community empowerment and how a model like MVP 2.0 can shift conditions that hold systems in place. In a practical sense, our findings will help municipalities reflect on their work during MVP 2.0 and plan for future community engagement. They may be informative for designing future iterations of the MVP program and for other municipalities, offices of community engagement, and practitioners. The findings will also contribute to the participation, resilience, and climate justice literatures, by adding perspectives on equity-centered resilience and community engagement approaches in smaller towns and rural settings. References: Adger, W. N. (2003). Social capital, collective action, and adaptation to climate change. Economic Geography, 79, 387-404. Allen, D. (2016). Toward a connected society. Our compelling interests: The value of diversity for democracy and a prosperous society, 71-105. Few, R., Brown, K., & Tompkins, E. L. (2007). Public participation and climate change adaptation: avoiding the illusion of inclusion. Climate Policy, 7(1), 46–59. Malloy, J. T., & Ashcraft, C. M. (2020). A framework for implementing socially just climate adaptation. Climatic Change, 160(1), 1–14. Smith, P. D., & McDonough, M. H. (2001). Beyond public participation: Fairness in natural resource decision making. Society & natural resources, 14(3), 239-249. Vale, L. J. (2014). The politics of resilient cities: whose resilience and whose city? Building Research & Information, 42(2), 191–201.

Callaham, Shannon↗

Computational Thermodynamics of Materials Zi-Kui Liu and Yi Wang

This authoritative volume introduces the reader to computational thermodynamics and the use of this approach to the design of material properties by tailoring the chemical composition. The text covers applications of this approach, introduces the relevant computational codes, and offers exercises at the end of each chapter. The book has nine chapters and two appendices that provide background material on computer codes. Chapter 1 covers the first and second laws of thermodynamics, introduces the spinodal as the limit of stability, and presents the Gibbs-Duhem equation. Chapter 2 focuses on the Gibbs energy function. Starting with a homogeneous system with a single phase, the authors proceed to phases with variable compositions, and polymer blends. The discussion includes the contributions of external electric and magnetic fields to the Gibbs energy. Chapter 3 deals with phase equilibria in heterogeneous systems, the Gibbs phase rule, and phase diagrams. Chapter 4 briefly covers experimental measurements of thermodynamic properties used as input for thermodynamic modeling by Calculation of Phase Diagrams (CALPHAD). Chapter 5 discusses the use of density functional theory to obtain thermochemical data and fill gaps where experimental data is missing. The reader is introduced to the Vienna Ab Initio Simulation Package (VASP) for density functional theory and the YPHON code for phonon calculations. Chapter 6 introduces the modeling of Gibbs energy of phases with the CALPHAD method. Chapter 7 deals with chemical reactions and the Ellingham diagram for metal-oxide systems and presents the calculation of the maximum reaction rate from equilibrium thermodynamics. Chapter 8 is devoted to electrochemical reactions and Pourbaix diagrams with application examples. Chapter 9 concludes this volume with the application of a model of multiple microstates to Ce and Fe3Pt. CALPHAD modeling is briefly discussed in the context of genomics of materials. The book introduces basic thermodynamic concepts clearly and directs readers to appropriate references for advanced concepts and details of software implementation. The list of references is quite comprehensive. The authors make liberal use of diagrams to illustrate key concepts. The two Appendices at the end discuss software requirements and the file structure, and present templates for special quasi-random structures. There is also a link to download pre-compiled binary files of the YPHON code for Linux or Microsoft Windows systems. The exercises at the end of the chapters assume that the reader has access to VASP, which is not freeware. Readers without access to this code can work on a limited number of exercises. However, results from other first principles codes can be organized in the YPHON format as explained in the Appendix. This book will serve as an excellent reference on computational thermodynamics and the exercises provided at the end of each chapter make it valuable as a graduate level textbook. Reviewer: Ram Devanathan is Acting Director of Earth Systems Science Division, Pacific Northwest National Laboratory, USA.

36 MATERIALS SCIENCE↗

Numerical Integration of Viscoelastic Models

Accurate modeling of viscoelasticity remains an important consideration for a variety of materials (e.g. polymers and inorganic glasses). As such, over the previous decades a substantial body of work has been dedicated to developing appropriate constitutive models for viscoelasticity ranging from initial considerations of linear thermoviscoelasticity to more complex non-linear formulations incorporating fictive temperatures or potential energy clocks including the use of both internal state variable(ISV) and hereditary integral representations. Nonetheless, relatively limited (in comparison to plasticity) attention has been paid to the numerical integration of such schemes. In terms of integral based formulations, Taylor et al. first considered the problem of the integration of a linear viscoelasticity model. That work focused on the integration of the hereditary integrals and demonstrated improved performance of the new scheme with a custom finite element code over an existing finite difference reference. Chambers and Becker, using a free volume based shift factor, also considered the integration of the hereditary integrals and the impact on the problem of a pressurized thick-walled cylinder and developed an adaptive scheme to bound the error. Chambers later developed three-point Gauss and composite integration schemes for the hereditary integrals and noted improved accuracy. With respect to ISV-based schemes, formulations for the non-linear Schapery model have been proposed. However, in those efforts greater attention was paid to convergence of the non-linear solution scheme than impact of numerical integration. Various authors (e.g. Holzapfel and Simo and Hughes) have also studied the use of convolution integrals with differential forms of ISVs for temperature-independent formulations. Regardless, while the "potential energy clock" (PEC) and "simplified potential energy clock"(SPEC) models have been used to study a variety of non-linear responses (e.g.), limited attention has been paid to the numerical performance. As will be discussed later, the "clock" at the center of the formulations includes temperature and complex history dependence making the numerical integration of such a model even more challenging. Thus, in the current work an initial effort towards characterizing the numerical integration of the constitutive model through simplified problems is performed. To that end, in Section 2 the theory of the model is briefly presented while the numerical integration is discussed in Section 3. Results of various studies characterizing the numerical behavior and performance are then given in Section 4. Finally, some concluding remarks and thoughts for follow on works are provided in Section 5.

36 MATERIALS SCIENCE↗

Environmental Constraints that Limit Methanogenesis

Methanogens are active in many different ecosystems, including habitats with biologically-derived organic matter as substrates such as aquatic sediments, wetlands, agricultural or natural soils subject to inundation, sewage digesters, and the anoxic portions of animal digestive tracts. Methanogens are also present in habitats with geochemically-supplied substrates such as hot springs, hydrothermal vents, volcanically-influenced habitats, and, potentially, the deep crustal subsurface. Methanogens as a group tolerate a broad range of physicochemical conditions, including temperatures from -2 to 122°C, pH values of 3.0 to 10.2, salinities up to halite saturation, and pressures of at least 75 MPa. Globally, variations in methane emissions can be explained to a large degree by variations in temperature and water availability. The distribution and activity of methanogens are constrained by ecological interactions that can be stimulatory or competitive, and by physicochemical factors that act at the biochemical or bioenergetic levels. In addition to the constraints placed on methanogens by physicochemical extremes, methanogen distribution and activity are constrained by the availability of energy and nutrients, the presence of inhibitory molecules (most notably oxygen), and the seawater anion, sulfate, due to competitive ecological interactions. Although methanogen tolerances to individual extremes are documented in culture, and the corresponding biochemical adaptations are understood to varying degrees, the natural environment frequently presents combinations of extreme conditions and energy limitations that may limit methanogen distribution to less than the optimally tolerated range of a single parameter. Little is understood about the compound effects of such extremes, nor the commonalities among them that will ultimately form the basis for predictive models of environmental methanogen population distribution. Future work that targets these questions, through a combination of culture work, “omic” analyses, in situ studies, and conceptual and quantitative models, will be needed to better understand the physiological ecology of methanogens.

54 ENVIRONMENTAL SCIENCES↗

Dosimetric validation of Acuros XB with Monte Carlo methods for photon dose calculations

Purpose: The dosimetric accuracy of the recently released Acuros XB advanced dose calculation algorithm (Varian Medical Systems, Palo Alto, CA) is investigated for single radiation fields incident on homogeneous and heterogeneous geometries, and a comparison is made to the analytical anisotropic algorithm (AAA). Methods: Ion chamber measurements for the 6 and 18 MV beams within a range of field sizes (from 4.0x4.0 to 30.0x30.0 cm{sup 2}) are used to validate Acuros XB dose calculations within a unit density phantom. The dosimetric accuracy of Acuros XB in the presence of lung, low-density lung, air, and bone is determined using BEAMnrc/DOSXYZnrc calculations as a benchmark. Calculations using the AAA are included for reference to a current superposition/convolution standard. Results: Basic open field tests in a homogeneous phantom reveal an Acuros XB agreement with measurement to within {+-}1.9% in the inner field region for all field sizes and energies. Calculations on a heterogeneous interface phantom were found to agree with Monte Carlo calculations to within {+-}2.0%({sigma}{sub MC}=0.8%) in lung ({rho}=0.24 g cm{sup -3}) and within {+-}2.9%({sigma}{sub MC}=0.8%) in low-density lung ({rho}=0.1 g cm{sup -3}). In comparison, differences of up to 10.2% and 17.5% in lung and low-density lung were observed in the equivalent AAA calculations. Acuros XB dose calculations performed on a phantom containing an air cavity ({rho}=0.001 g cm{sup -3}) were found to be within the range of {+-}1.5% to {+-}4.5% of the BEAMnrc/DOSXYZnrc calculated benchmark ({sigma}{sub MC}=0.8%) in the tissue above and below the air cavity. A comparison of Acuros XB dose calculations performed on a lung CT dataset with a BEAMnrc/DOSXYZnrc benchmark shows agreement within {+-}2%/2mm and indicates that the remaining differences are primarily a result of differences in physical material assignments within a CT dataset. Conclusions: By considering the fundamental particle interactions in matter based on theoretical interaction cross sections, the Acuros XB algorithm is capable of modeling radiotherapy dose deposition with accuracy only previously achievable with Monte Carlo techniques.

60 APPLIED LIFE SCIENCES↗

Crystal Structure of a Complex between Amino and Carboxy Terminal Fragments of mDia1: Insights into Autoinhibition of Diaphanous-Related Formins

Formin proteins direct the nucleation and assembly of linear actin filaments in a variety of cellular processes using their conserved formin homology 2 (FH2) domain. Diaphanous-related formins (DRFs) are effectors of Rho-family GTPases, and in the absence of Rho activation they are maintained in an inactive state by intramolecular interactions between their regulatory N-terminal region and a C-terminal segment referred to as the DAD domain. Although structures are available for the isolated DAD segment in complex with the interacting region in the N-terminus, it remains unclear how this leads to inhibition of actin assembly by the FH2 domain. Here we describe the crystal structure of the N-terminal regulatory region of formin mDia1 in complex with a C-terminal fragment containing both the FH2 and DAD domains. In the crystal structure and in solution, these fragments form a tetrameric complex composed of two interlocking N+C dimers. Formation of the tetramer is likely a consequence of the particular N-terminal construct employed, as we show that a nearly full-length mDia1 protein is dimeric, as are other autoinhibited N+C complexes containing longer N-terminal fragments. The structure provides the first view of the intact C-terminus of a DRF, revealing the relationship of the DAD to the FH2 domain. Delineation of alternative dimeric N+C interactions within the tetramer provides two general models for autoinhibition in intact formins. In both models, engagement of the DAD by the N-terminus is incompatible with actin filament formation on the FH2, and in one model the actin binding surfaces of the FH2 domain are directly blocked by the N-terminus.

59 BASIC BIOLOGICAL SCIENCES↗

Design of water-moderated heterogeneous cores in new STACY facility through JAEA/IRSN collaboration - 14363

In the post-Fukushima prospect, Japan Atomic Energy Agency, JAEA, intends to re-open its Static Experiment Critical Facility STACY, in order to contribute to the validation of fuel debris calculations in conditions close to those affected by the Fukushima Daiichi Nuclear Power Station accident. The reactor core of STACY is being modified by JAEA from homogeneous solution fuel core to heterogeneous pin- type fuel core. The first step of critical experiments is to establish reference experiments involving lattices of UO{sub 2} rods without fuel debris. A design of such experiments is in progress for the widest range of moderation ratios in the frame of JAEA/IRSN collaboration. To anticipate the specification values of materials to be manufactured (grids, rods), an evaluation of uncertainties pertaining to the different parameters driving k{sub eff} is paramount. The following uncertainties of experimental cores are evaluated to estimate the reactivity effect of engineering tolerance/or measurements of the modified STACY: (1) Density of fuel pellets, (2) Enrichment of uranium, (3) Diameter of fuel pellets, (4) Thickness of fuel claddings, (5) Impurities of fuel pellets, (6) Impurities of fuel claddings and (7) Positioning of fuel rods in the lattice. For these calculations, three types of moderation conditions were considered within the experimental parameters of STACY: the lowest moderation (lattice pitch = 1.15 cm; V{sub m}/V{sub f}=1.2), optimum moderation (lattice pitch = 1.5 cm, V{sub m}/V{sub f} = 2.9) and an over moderated case (lattice pitch = 2.55 cm; V{sub m}/V{sub f} = 11). The calculations to derive the overall uncertainty of modified STACY were performed propagating the 1σ uncertainties of parameters of existing STACY in terms of k{sub eff}. For that purpose, a perturbation calculation (differential operator) technique and a stochastic geometry modeling technique were used with the MCNP5 continuous energy Monte Carlo code and a point-wise cross section library based on the JENDL-4.0 evaluated nuclear data library. Moreover, the results of calculations were compared with those calculated by two continuous energy Monte Carlo codes using the correlated sampling technique: - An experimental version of the Japanese MVP2 code combined to the JENDL-4.0 nuclear data library, - The MORET 5 code, developed by IRSN, combined to the JEFF-3.1 nuclear data library. The proposed paper discusses all the aforementioned issues, and confirms that the uncertainty pertaining to the critical experiments of the STACY is sufficiently small. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SU-G-TeP2-05: Development of a Thimble Calorimeter for Absorbed Dose to Water Characterized in MV Photons

Purpose: To develop a thimble sized polystyrene calorimeter for use from kV to MV photons, as a primary reference standard for applications from diagnostic CT imaging to therapy beam dose determination. Methods: A polystyrene calorimeter about 1.5 cm diameter embedded with small thermistors was characterized in a 6 MV photon beam from a clinical accelerator at 5 nominal dose rates from 0.8 to 4 Gy/min. Irradiations were delivered with beam on/off cycles first at 60 s and then at 20 s. Two sets of phantom conditions were evaluated: 1) in a 30 cm diameter polyethylene cylinder, and 2) in 10 cm depth of a 30 cm water phantom. The temperature waveforms were recorded and analyzed for temperature rise, arriving at a dose to polystyrene. This value is compared with the result of measurements under identical conditions using an ionization chamber calibrated for absorbed dose to water. Monte Carlo simulations were performed on the measurement systems to estimate such a ratio. Results: The ratio of the dose determined by the calorimeter to the dose reported by the ionization chamber was aggregated from all 5 dose rates. The 60 s results show a much elevated response in both phantoms compared to their respective expected results based on simulation. This deviation was reduced when the on/off cycles were shortened to 20 s. This behavior was possibly due to the heat conduction effects in the small calorimeter body. Finite element modeling is being conducted to simulate this effect. Conclusion: A small solid plastic calorimeter offers the convenience of a portable absorbed dose standard based on direct measurement of energy deposition, but comes at the expense of heat transfer complications which need to be characterized. This work offers preliminary evidence of the behavior and quantitative assessment of the issues to be resolved in future investigations.

60 APPLIED LIFE SCIENCES↗

The Impact of Stochastic Perturbations in Physics Variables for Predicting Surface Solar Irradiance

We present a probabilistic framework tailored for solar energy applications referred to as the Weather Research and Forecasting-Solar ensemble prediction system (WRF-Solar EPS). WRF-Solar EPS has been developed by introducing stochastic perturbations into the most relevant physical variables for solar irradiance predictions. In this study, we comprehensively discuss the impact of the stochastic perturbations of WRF-Solar EPS on solar irradiance forecasting compared to a deterministic WRF-Solar prediction (WRF-Solar DET), a stochastic ensemble using the stochastic kinetic energy backscatter scheme (SKEBS), and a WRF-Solar multi-physics ensemble (WRF-Solar PHYS). The performances of the four forecasts are evaluated using irradiance retrievals from the National Solar Radiation Database (NSRDB) over the contiguous United States. We focus on the predictability of the day-ahead solar irradiance forecasts during the year of 2018. The results show that the ensemble forecasts improve the quality of the forecasts, compared to the deterministic prediction system, by accounting for the uncertainty derived by the ensemble members. However, the three ensemble systems are under-dispersive, producing unreliable and overconfident forecasts due to a lack of calibration. In particular, WRF-Solar EPS produces less optically thick clouds than the other forecasts, which explains the larger positive bias in WRF-Solar EPS (31.7 W/m 2 ) than in the other models (22.7–23.6 W/m 2 ). This study confirms that the WRF-Solar EPS reduced the forecast error by 7.5% in terms of the mean absolute error (MAE) compared to WRF-Solar DET, and provides in-depth comparisons of forecast abilities with the conventional scientific probabilistic approaches (i.e., SKEBS and a multi-physics ensemble). Guidelines for improving the performance of WRF-Solar EPS in the future are provided.

14 SOLAR ENERGY↗

WIMS/PANTHER analysis of UO{sub 2}/MOX cores using embedded super-cells

This paper describes a method of analysing PWR UO{sub 2}MOX cores with WIMS/PANTHER. Embedded super-cells, run within the reactor code, are used to correct the standard methodology of using 2-group smeared data from single assembly lattice calculations. In many other codes the weakness of this standard approach has been improved for MOX by imposing a more realistic environment in the lattice code, or by improving the sophistication of the reactor code. In this approach an intermediate set of calculations is introduced, leaving both lattice and reactor calculations broadly unchanged. The essence of the approach is that the whole core is broken down into a set of 'embedded' super-cells, each extending over just four quarter assemblies, with zero leakage imposed at the assembly mid-lines. Each supercell is solved twice, first with a detailed multi-group pin-by-pin solution, and then with the standard single assembly approach. Correction factors are defined by comparing the two solutions, and these can be applied in whole core calculations. The restriction that all such calculations are modelled with zero leakage means that they are independent of each other and of the core-wide flux shape. This allows parallel pre-calculation for the entire cycle once the loading pattern has been determined, in much the same way that single assembly lattice calculations can be pre-calculated once the range of fuel types is known. Comparisons against a whole core pin-by-pin reference demonstrates that the embedding process does not introduce a significant error, even after burnup and refuelling. Comparisons against a WIMS reference demonstrate that a pin-by-pin multi-group diffusion solution is capable of capturing the main interface effects. This therefore defines a practical approach for achieving results close to lattice code accuracy, but broadly at the cost of a standard reactor calculation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

International Linear Collider Technical Design Report - Volume 2: Physics

For more than twenty years, an advanced electron-positron collider has been put forward as a key component of the future program of elementary particle physics. We have a well-established Standard Model of particle physics, but it is known to be incomplete. Among the many questions that this model leaves open, there are two — the origin of the masses of elementary particles and the particle identity of cosmic dark matter – that should be addressed at energy scales below 1 TeV. It has been appreciated for a long time that a next-generation electron-positron collider would give us the ability to make precision measurements that would shed light on these mysteries. Now the technology to build this electron-positron collider has come of age. This report is a volume of the Technical Design Report for the International Linear Collider (ILC). The accompanying volumes of this report lay out the technical design of a high-luminosity e + e - collider at 500 GeV in the center of mass and of detectors that could make use of the collisions to perform high-precision measurements. In this volume, we summarize the physics arguments for building this collider and their appropriate relation to the situation of particle physics as of the fall of 2012. The discussion in this volume supplements the presentation of the physics opportunities for a 500 GeV e + e - collider given in the review articles, the 2001 regional study reports, the 2006 study of ILC/LHC complementarity, and the 2007 ILC Reference Design Report.

43 PARTICLE ACCELERATORS↗