Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Measurement of Diameter Changes during Irradiation Testing

New materials are being considered for fuel, cladding, and structures in advanced and existing nuclear reactors. Such materials can experience significant dimensional and physical changes during irradiation. Currently in the US, such changes are measured by repeatedly irradiating a specimen for a specified period of time and then removing it from the reactor for evaluation. The time and labor to remove, examine, and return irradiated samples for each measurement makes this approach very expensive. In addition, such techniques provide limited data and handling may disturb the phenomena of interest. In-pile detection of changes in geometry is sorely needed to understand real-time behavior during irradiation testing of fuels and materials in high flux US Material and Test Reactors (MTRs). This paper presents development results of an advanced Linear Variable Differential Transformer-based test rig capable of detecting real-time changes in diameter of fuel rods or material samples during irradiation in US MTRs. This test rig is being developed at the Idaho National Laboratory and will provide experimenters with a unique capability to measure diameter changes associated with fuel and cladding swelling, pellet-clad interaction, and crud buildup.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimental Validation of the Methodology for Partial Defect Verification of the Pressurized Water Reactor Spent Fuel Assemblies

A set of controlled experiments and Monte Carlo simulation studies with actual commercial pressurized water reactor (PWR) spent fuel assemblies were performed in order to validate an earlier proposal for partial defect testing of the PWR spent fuel assemblies. The proposed methodology involved insertion of tiny neutron and gamma detectors into the guide tubes of PWR assemblies, measurements and data evaluation. One of the key features of the data evaluation method was the concept of the base signature obtained by normalizing the ratio of gamma to neutron signals at each measurement position. As the base signature is relatively invariant to the characteristic variations of spent fuel assemblies such as initial fuel enrichment, cooling time, and burn-up, the methodology could be a powerful verification method which does not require operator declared information on the spent fuel. The benchmarking experiments indeed demonstrated that the methodology can be used for partial defect verification of the PWR spent fuel assemblies without operator declared data. The results from the experiments were compared with the simulations and the agreement between the two was well within ten percent. Thus, based on the simulation studies and benchmarking measurements, the methodology developed promises to be a powerful and practical way to detect partial defects that constitute 10% or more of the total active fuel pins. This far exceeds the detection threshold of 50% missing pins from a spent fuel assembly, a threshold defined by the IAEA Safeguards Criteria.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Integrated friction reduction technology to improve fuel economy without sacrificing durability

This project aims to develop fuel economy technologies to minimize parasitic losses within vehicle engines and drivetrains by improving fuel economy at least 2% for 2014 legacy vehicles and 2018 vehicles without adverse impacts on engine durability. The tools used are advanced low viscosity lubricants and surface material technologies, including surface textures, and coatings. Working with industrial partners, an experimental fuel efficient low viscosity lubricant was developed, verified by ASTM fuel economy engine test for 2014 vehicle population. An ultralow viscosity lubricant was also developed for 2018 engines, demonstrated by engine chassis dynamometer tests. Surface texturing of engine components was also conducted, and in engine testing, confirmed the textured engine developed more torque and power while the textures largely stayed intact after the test.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Real-Time Gear-Shift Optimization for an Autonomous Wheel Loader

Off-road vehicles, such as wheel loaders, consume a significant amount of fuel during the transportation of materials. The gear-shifting process is crucial in fuel savings for transportation, and therefore, optimization of gearshifts is important for vehicle control. For an autonomous off-road vehicle, there is potential for more fuel savings by proper coordination of gearshift optimization and optimization of other control inputs. This brief proposes a new method for integrating gear-shifting into transportation optimization for an autonomous wheel loader to minimize fuel consumption. Furthermore, tests conducted on short loading cycles show that this method can save around 10%–20% of fuel on average compared with a conventional gearshift-scheduling method.

33 ADVANCED PROPULSION SYSTEMS↗

Water-based Ria Testing in TREAT: Commissioning and Early Results

We have completed a series of reactivity-initiated accident commissioning tests with the static water capsule in the Transient Reactor Test Facility and completed some visual and non-destructive post-irradiation examinations on the fuel rods. The test campaign included a calibration test followed by five tests in the Static Environment Rodlet Transient Test Apparatus capsule. The conditions varied from room temperature and pressure up to 200°C and 2.5 MPa, with energy depositions varying between ~500–1100 J/gUO2. The series of tests allowed for a number of instrumentation qualifications and demonstrations, including cladding thermometry, rodlet plenum pressure, cladding elongation, and an electro-impedance boiling detector. This paper documents the design of the capsule and highlights some results from the commissioning tests and post-transient examination.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Impacts Analyses Supporting the National Environmental Policy Act Environmental Assessment for the Resumption of Transient Testing Program

This document contains the analysis details and summary of analyses conducted to evaluate the environmental impacts for the Resumption of Transient Fuel and Materials Testing Program. It provides an assessment of the impacts for the two action alternatives being evaluated in the environmental assessment. These alternatives are (1) resumption of transient testing using the Transient Reactor Test Facility (TREAT) at Idaho National Laboratory (INL) and (2) conducting transient testing using the Annular Core Research Reactor (ACRR) at Sandia National Laboratory in New Mexico (SNL/NM). Analyses are provided for radiologic emissions, other air emissions, soil contamination, and groundwater contamination that could occur (1) during normal operations, (2) as a result of accidents in one of the facilities, and (3) during transport. It does not include an assessment of the biotic, cultural resources, waste generation, or other impacts that could result from the resumption of transient testing. Analyses were conducted by technical professionals at INL and SNL/NM as noted throughout this report. The analyses are based on bounding radionuclide inventories, with the same inventories used for test materials by both alternatives and different inventories for the TREAT Reactor and ACRR. An upper value on the number of tests was assumed, with a test frequency determined by the realistic turn-around times required between experiments. The estimates provided for impacts during normal operations are based on historical emission rates and projected usage rates; therefore, they are bounding. Estimated doses for members of the public, collocated workers, and facility workers that could be incurred as a result of an accident are very conservative. They do not credit safety systems or administrative procedures (such as evacuation plans or use of personal protective equipment) that could be used to limit worker doses. Doses estimated for transportation are conservative and are based on transport of the bounding radiologic inventory that will be contained in any given test. The transportation analysis assumes all transports will contain the bounding inventory.

99 GENERAL AND MISCELLANEOUS↗

Compilation of Quality Assurance Documentation for Analyses Performed for the Resumption of Transient Testing Environmental Assessment

This is a companion document to the analyses performed in support of the environmental assessment for the Resumption of Transient Fuels and Materials Testing. It is provided to allow transparency of the supporting calculations. It provides computer code input and output. The basis for the calculations is documented separately in INL (2013) and is referenced, as appropriate. Spreadsheets used to manipulate the code output are not provided.

99 GENERAL AND MISCELLANEOUS↗

AFUE Analysis Software Tool

The Annual Fuel Utilization Efficiency (AFUE) analysis of residential and light commercial furnaces follows ANSI/ASHRAE Standard 103-2017 (i.e., Method of Testing for Annual Fuel Utilization Efficiency of Residential Central Furnaces and Boilers) . The analysis is a complex, comprehensive method based on furnace configuration and specific components equipped, requiring detailed furnace testing and measurement data. For this reason, an AFUE Analysis Tool using Microsoft Excel enabled with Visual Basic for Applications (VBA) was developed with a user-friendly interface and comprehensive coverage. The tool consists of three worksheets: unit and configuration selection, geometry and measurement data input, and AFUE plus key results. This tool can be used to estimate the AFUE of both condensing and noncondensing furnaces with single-stage, two-stage, and step-modulating functions. The tool was validated with experimental data from Oak Ridge National Laboratory’s natural gas furnace projects that are commercially available. The results indicate the tool is reasonably accurate in the evaluation of a new R&D modified furnace unit.

Gao, Zhiming [Oak Ridge National Laboratory (ORNL)↗

Effect of fuel molecular structure on soot formation in gas turbine combustion

The effect of fuel variations at the same hydrogen content on the formation of soot in a gas turbine combustor was studied. Six fuels were burned to a combustor over a matrix of about 50 test conditions with test conditions ranging over 500-1800 kPa (5-18 atm) pressure and 500-1000 K burner inlet temperature; fuel-air ratios were varied from 0.008-0.024. Flame radiation measurements were made through a sapphire window toward the end of the primary zone. The hydrogen content of the six test fuels ranged from 12.80 to 12.88%. Five fuels emphasized hydrocarbon types: (mono, di, and tricyclic), naphthenes (decalin) and partially hydrogenated aromatics (tetralin); the sixth fuel emphasized final boiling point.

Naegeli, D. W.↗

Co-optimized Mixed-Mode Engine and Fuel Demonstrator for Improved Fuel Economy while Meeting Emissions Requirements

Progressively increasing regulatory demands on fuel economy and future global emission standards have led to a focus on advanced engine development to improve overall engine efficiency and fulfill emission requirements. Low temperature combustion (LTC) and gasoline compression ignition (GCI) are promising technologies to achieve these goals and have the advantage of using existing refinery infrastructure and subsequent economies of scale for a robust energy supply. By applying spark ignition (SI) for cold start, LTC for low load operations, and GCI for medium to high load operations, a multimode GCI engine concept was proposed and the fuel formation was co-optimized to maximize fuel economy improvement potential while maintaining ULEV 70 emissions standards. HATCI has successfully demonstrated the feasibility of this multimode GCI engine concept, and confirmed the fuel economy improvement over the baseline SI engine by simulating the FTP75 vehicle drive cycle. In this report, the technical approaches, multimode engine control, and engine test results of both steady state and transitions, CFD modeling, fuel testing, and FTP75 drive cycle simulation results are summarized, followed with technical challenges observed, and recommendations for possible follow-up studies.

02 PETROLEUM↗

Status and Availability of OPTD, the Out-of-Pile Transient Database

The DOE Advanced Reactor Technology program has supported knowledge preservation efforts to recover and preserve fuel data from the US sodium cooled fast reactor (SFR) program. Databases have been established containing experimental data generated during the Integral Fast Reactor program (from in-pile experiments at EBR-II, FFTF, and TREAT) and during related outof-pile examinations of EBR-II-irradiated fuels. The information in these databases is essential to support further development and licensing activities for advanced fast reactor designs. OPTD, the Out-of-Pile Transient Database, is an organized, searchable archive of records describing out-ofpile furnace transient tests conducted on metallic fuels. It includes records of over 150 tests on irradiated fuel pins conducted in furnace apparatuses constructed in the Alpha-Gamma Hot Cell Facility at ANL. This report presents the content, functions, and accessibility of the Out-of-Pile Transient Database (OPTD). It describes the information presently available in the database, the web interface created to provide access to this information, the activities undertaken to build OPTD, and the enabling of online access to the database for DOE users. Plans for FY2021 and beyond are also included.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance and durability of improved air-atomizing splash-cone fuel nozzles

An improved design of air-atomizing fuel nozzles was determined from a study of four differently shaped splash-cone fuel nozzles after 56 hr of durability testing in a combustor segment. Test conditions included fuel-air ratios of 0.008 to 0.018, inlet-air total pressures of 41 to 203 N/cm, inlet-air temperatures of 477 to 811 K, and a reference velocity of 21.3 m/sec. Flat-tip fuel nozzles showed the least erosion damage and at a combustor operating condition of 700 K and 101 N/sq cm an oxides-of-nitrogen emission index of 12 and a smoke number of approximately 18 with a fuel-air ratio of 0.018. Emission indices for carbon monoxide and unburned hydrocarbons were 44 and 16, respectively, at simulated idle conditions of 477 K and 41 N/sq cm.

Ingebo, R. D.↗

Cost/benefit trade-offs for reducing the energy consumption of commercial air transportation (RECAT)

The RECAT study evaluated the opportunities for reducing the energy requirements of the U.S. domestic air passenger transport system through improved operational techniques, modified in-service aircraft, derivatives of current production models, or new aircraft using either current or advanced technology. Each of these fuel-conserving alternatives was investigated individually to test its potential for fuel conservation relative to a hypothetical baseline case in which current, in-production aircraft types are assumed to operate, without modification and with current operational techniques, into the future out to the year 2000. Consequently, while the RECAT results lend insight into the directions in which technology can best be pursued for improved air transport fuel economy, no single option studied in the RECAT program is indicative of a realistic future scenario.

Gobetz, F. W.↗

Capacitance-Based Dimensional Change Sensors for In-Pile Materials Measurements

Advanced fuel compositions, such as accident tolerate fuels (ATF), are an active area of developing in the nuclear power industry. The long-term performance of these newly developed fuels is estimated through physics-based simulation models of irradiation-, temperature-, pressure-, etc.-induced material degradation. As these fuels are deployed in test reactors, measurement and characterization of the fuel pin evolution is used to validate prediction models. In-pile material evolution parameters, such as fuel rod pressurization, fuel stack and cladding elongation, and cladding diameter, are commonly measured using a linear voltage differential transformer (LVDT). However, LVDTs are bulky and limited to lower (350-500C) temperature operation. The high power density and small size of most experimental positions in high performance research reactors used for accelerated materials irradiation studies generally precludes the use of LVDTs in these reactors. There is a critical need for sensors that provide real-time data regarding material evolution under highly accelerated irradiation. These sensors would ideally have a small profile and the ability to withstand irradiation at extremely high dose rates and temperatures for extended periods of time. A capacitance-based sensor is currently under development at the University of Tennessee to provide a direct measurement of in-pile dimensional change during irradiation. Sensor response was simulated using AutoCAD Electromagnetic field simulator (EMS) for a variety of sensor materials and configurations and fuel pin swelling conditions. Initial results of these simulations are summarized and areas of ongoing research and development are discussed.

Naughton, Tyler↗

Effects of Coolant Void Condition on Melt Fragmentation using Simulants in Initial Phase of Metal-fueled SFR Severe Accident

Metal fuel has inherent safety characteristics, especially in severe accident conditions. However, the metal-fueled SFR severe accident scenarios need to be categorized since overall severe accident mitigation strategies have not been prepared. In addition, these mitigation strategies should be classified in specific phases. In an initial phase of metal-fueled SFR severe accident scenarios, fuel melting, and cladding failures would occur. After the occurrence of the cladding breach, the molten metal fuel would be ejected into a coolant channel due to fission gas in fuel cavity or rapid evaporation of sodium bond. This is called Ex-pin phenomena. There are few studies considering the Ex-pin phenomena of metal fuel. Related representative studies are transient reactor test facility (TREAT) M series tests. The TREAT M series tests provided fundamental metal fuel performance in transient condition. They informed partial experimental data such as the amount of melt ejected into coolant channel after the cladding failure. However, these experimental data did not examine the melt behavior during the Ex-pin phenomena. In metal-fueled SFR, it is a known fact that the negative reactivity feedback occurs in the initial phase of severe accident. In an unprotected loss-of-flow (ULOF) accident, the void-reactivity feedback may be positive depending on where in the reactor core the sodium voiding occurs. However, molten metal fuel would be better dispersed upward compared to those of an oxide fuel and significant negative reactivity feedback could be induced through such behaviors. Thus, a key safety strategy to mitigate the accident progression at the initial phase of severe accident is to discharge melt upwards out of the core. In this paper, the upward discharge of melt is defined as melt levitation. Such melt levitation could ensure early termination of severe accident. There could be different melting behaviors inside the pin depending on reactor types or the type of fuel. In case of pressurized water reactor (PWR) oxide fuel-water system, the rapid power excursion would initiate melting of fuel at the surface of the pellets. In this paper, the ULOF accident for the metal-fueled SFR is considered as an accident scenario. To induce the melt levitation, the driving force should be clarified. Heo et al. observed a built-up vapor pressure was suggested as one of the driving forces for the upward dispersion of the molten materials. The following factors also have the potential to induce the melt levitation; the pressure induced by fission gas in the cavity or rapid boiling of sodium bond, natural circulation flow of the sodium, the sodium vapor flow generated by the difference between inlet and outlet plenum in the reactor core, the built-up vapor pressure due to the fuel-coolant interaction etc. These factors are balanced each other. They should be examined through the Ex-pin experiments. Before conducting a parametric study for each factor, the general behavior of the molten metal fuel should be investigated in the coolant channel. Since rapid sodium coolant boiling could occur in the initial phase of severe accident scenarios, the molten fuel would be ejected and fragmented in voided channel. Unlike previous studies concerning an un-voided channel, differences in melt behavior in the voided channel are expected. In present study, molten material behavior was evaluated to reveal their characteristics in voided channel. The Ex-pin experiments were performed in both un-voided and voided channel, thus such behavior differences were explicitly observed. In the lab-scale experiments, the un-voided and voided channel were reflected by coolant-filled and air-filled channel, respectively. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Current Development of Nuclear Thermal Propulsion technologies at the Center for Space Nuclear Research

Nuclear power and propulsion has been considered for space applications since the 1950s. Between 1955 and 1972 the US built and tested over twenty nuclear reactors / rocket engines in the Rover/NERVA programs1. The Aerojet Corporation was the prime contractor for the NERVA program. Modern changes in environmental laws present challenges for the redevelopment of the nuclear rocket. Recent advances in fuel fabrication and testing options indicate that a nuclear rocket with a fuel composition that is significantly different from those of the NERVA project can be engineered; this may be needed to ensure public support and compliance with safety requirements. The Center for Space Nuclear Research (CSNR) is pursuing a number of technologies, modeling and testing processes to further the development of safe, practical and affordable nuclear thermal propulsion systems.

99 GENERAL AND MISCELLANEOUS↗

Performance of Pentaborane, Pentaborane - JP-4 Fuel Mixtures, and Trimethylborate Azeotrope Fuel in a Full-scale Turbojet Engine

This report summarizes the full-scale engine tests of pentaborane, pentaborane - JP-4 fuel mixtures, and trimethylborate azeotrope fuel. The tests were conducted in a full-scale turbojet engine at a simulated altitude of 50,000 feet and Mach number of 0.08. Engine speeds were 90 to 100 percent of rated speed. Pentaborane reduced the the specific fuel consumption to two-thirds that of JP-4 fuel. However, because boron oxide collected in the engine, the performance deteriorated with continued operation of pentaborane in each of the short-duration tests reported.

Breitwiesser, Roland↗