Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lattice optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Quantifying Dynamic Signal Spread in Real-Time High-Energy X-ray Diffraction

Abstract Measured intensity in high-energy monochromatic X-ray diffraction (HEXD) experiments provides information regarding the microstructure of the crystalline material under study. The location of intensity on an areal detector is determined by the lattice spacing and orientation of crystals so that changes in the heterogeneity of these quantities are reflected in the spreading of diffraction peaks over time. High temporal resolution of such dynamics can now be experimentally observed using technologies such as the mixed-mode pixel array detector (MM-PAD) which facilitates in situ dynamic HEXD experiments to study plasticity and its underlying mechanisms. In this paper, we define and demonstrate a feature computed directly from such diffraction time series data quantifying signal spread in a manner that is correlated with plastic deformation of the sample. A distinguishing characteristic of the analysis is the capability to describe the evolution from the distinct diffraction peaks of an undeformed alloy sample through to the non-uniform Debye–Scherrer rings developed upon significant plastic deformation. We build on our previous work modeling data using an overcomplete dictionary by treating temporal measurements jointly to improve signal spread recovery. We demonstrate our approach in simulations and on experimental HEXD measurements captured using the MM-PAD. Our method for characterizing the temporal evolution of signal spread is shown to provide an informative means of data analysis that adds to the capabilities of existing methods. Our work draws on ideas from convolutional sparse coding and requires solving a coupled convex optimization problem based on the alternating direction method of multipliers.

Engineering↗

Ferroelectric, piezoelectric, and dielectric properties of BiScO{sub 3}-PbTiO{sub 3}-Pb(Cd{sub 1/3}Nb{sub 2/3})O{sub 3} ternary high temperature piezoelectric ceramics

(0.95-x)BiScO{sub 3}-xPbTiO{sub 3}-0.05Pb(Cd{sub 1/3}Nb{sub 2/3})O{sub 3} (BS-xPT-PCN) high temperature piezoelectric ceramics near the morphotropic phase boundary (MPB) have been synthesized by traditional solid-state reaction methods. The microstructural morphology, phase structure, and electrical properties of BS-xPT-PCN ceramics were investigated in detail. X-ray diffraction analysis indicated BS-xPT-PCN ceramics have a pure perovskite structure. The coexistence of rhombohedral and tetragonal phases at MPB composition enhanced the polarizability by the coupling between two dynamically equivalent energy states, resulting in the improved piezoelectric and ferroelectric properties at MPB vicinity. The BS-xPT-PCN (x = 0.60) ceramics possess the optimal piezoelectric and ferroelectric properties with d{sub 33} = 505pC/N, k{sub p} = 55.9%, k{sub t} = 36.5%, strain = 0.23% (under the electric field 37.5 kV/cm), and P{sub r} = 39.7 {mu}C/cm{sup 2}. High temperature dielectric behaviors showed diffuse phase transition in BS-xPT-PCN ceramics. The Curie temperature T{sub c} was found to increase from 371 Degree-Sign C to 414 Degree-Sign C with x increasing from 0.58 to 0.62. All these results together with the good thermal stabilities make the BS-xPT-PCN ceramics promising candidates for high temperature piezoelectric applications.

36 MATERIALS SCIENCE↗

Synthesis and characterization of brownmillerite SrFeO{sub 2.5} in nanostructured form

Synthesis of bulk polycrystalline and nanocrystalline oxygen-deficient SrFeO{sub 2.5} compounds, with potential applications as oxygen membranes, has been explored by chemical route to optimize an easy and reproducible method for high yield. The structure of the samples was investigated by X-ray powder diffraction followed by structural refinement. Both bulk and nanocrystalline SrFeO{sub 2.5} crystallize in Imma space group. X-ray powder diffraction pattern corresponds to the brownmillerite structure in which the Fe cations exist in an octahedral or tetrahedral configuration in alternate layers along the b axis. Brunauer−Emmett−Teller (BET) surface area is found to be 0.40m{sup 2}/g and 14 m{sup 2}/g for bulk and nanocrystalline SrFeO{sub 2.5} respectively. The morphology of these materials was also investigated by scanning electron microscopy and transmission electron microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A twist grain boundary phase in aqueous solutions of the nucleic acid tetramer GTAC

At high concentration, long Watson/Crick (WC) double-helixed DNA forms columnar crystal or liquid crystal phases of linear, parallel duplex chains packed on periodic lattices. This can also be a structural motif of short NA oligomers such as the 5’-GTAC-3’ studied here, which makes four-base WC duplexes having hydrophobic blunt ends. End-to-end aggregation then assembles these duplexes into columns and columnar phases are stabilized, in spite of breaks in the double helix every four bases. But the new degrees of freedom introduced by such breaks also enable opportunities for a more diverse palette of self-assembly modes, producing striking self-assemblies of DNA that would not be achievable with contiguous polymers. These include recently reported three-dimensional (3D) periodic low-density nanoscale networks of GCCG, and the twist grain boundary (TGB) phase presented here. In the TGB, columns of GTAC pairs assemble into monolayer sheets in which the duplex columns are mutually parallel. However, unlike in the columnar crystals, these sheets stack in helical fashion into lamellar arrays in which the column axis of each layer is rotated through a 60° angle with respect to the columns in neighboring layers. This assembly of DNA is unique in that it the fills a 3D volume wherein the major grooves of columns in each layer mutually enter and interlock with the major grooves of columns in neighboring layers. This locking is optimized by small adjustments in structure enabled by the breaks in the duplex backbones.

DNA↗

Evolution of structure and spectroscopic properties of a new 1,3-diacetylpyrene polymorph with temperature and pressure

A new polymorph of 1,3-diacetylpyrene has been obtained from its melt and thoroughly characterized using single-crystal X-ray diffraction, steady-state UV–Vis spectroscopy and periodic density functional theory calculations. Experimental studies covered the temperature range from 90 to 390 K and the pressure range from atmospheric to 4.08 GPa. Optimal sample placement in a diamond anvil cell according to our previously presented methodology ensured over 80% data coverage up to 0.8 Å for a monoclinic sample. Unrestrained Hirshfeld atom refinement of the high-pressure crystal structures was successful and anharmonic behavior of carbonyl oxygen atoms was observed. Unlike the previously characterized polymorph, the structure of 2°AP-β is based on infinite π-stacks of antiparallel 2°AP molecules. 2°AP-β displays piezochromism and piezofluorochromism which are directly related to the variation in interplanar distances within the π-stacking. The importance of weak intermolecular interactions is reflected in the substantial negative thermal expansion coefficient of -55.8 (57) MK -1 in the direction of C—H∙∙∙O interactions.

36 MATERIALS SCIENCE↗

Elucidating effects of catalyst loadings and porous transport layer morphologies on operation of proton exchange membrane water electrolyzers

Producing green hydrogen efficiently via proton exchange membrane water electrolysis (PEMWE) is the key for achieving decarbonization targets. Iridium catalyst is expensive, and it is important to minimize its use and to optimize interface between Ir and ionomer or water for higher utilization of catalyst in oxygen evolution reaction. In this work, x-ray computed tomography along with electrochemical and modeling techniques are used to characterize the interface for two different porous transport layers (PTLs) and catalyst layers at various loadings. We show that low porosity sintered PTLs exhibit higher interfacial contact with the catalyst and the membrane that results in improved kinetics. Radiography and modeling results indicate that oxygen taking multiple transport pathways through the PTL results in slug flow through the channels that reduces mass transport overpotential. Based on the results, we suggest design guidelines for high efficiency and durable PEMWE and their components.

08 HYDROGEN↗

Selectivity of tris complexation for Ni(II), Co(II), and Fe(II) and its effect on carbonate precipitation under alkaline conditions

Simultaneous critical element recovery and ex-situ carbon mineralization of low-grade ultramafic deposits have garnered increasing interest. Understanding the selectivity of metal complexing organic ligands for various divalent metals present in ultramafic rocks during carbonate mineralization is required to optimize this process. Here we evaluate 2-amino-2-(hydroxymethyl)-1,3-propanediol (i.e., Tris) as a model for bidentate ligands that bind divalent metals with both amine and alcohol groups in alkaline conditions (pH 8–10.5) at 25 °C and 80 °C in carbonate-buffered solutions. Protonated Tris forms a stronger complex with metal ions and is selective for trace metals with Ni(II) > Co(II) > Fe(II) during carbonate precipitation, with the rates decreasing but selectivity increasing at lower temperature and lower pH. At 25 °C, metastable amorphous hydrated carbonates form, regardless of the amount of Tris present or pH values. At 80 °C and pH 8, the Co and Fe carbonates that form are a mixture of rosasite-group minerals (Co 2 CO 3 (OH) 2 (H 2 O) and Fe 2 CO 3 (OH) 2 ) and pure carbonates (sphaerocobaltite: CoCO 3 and siderite: FeCO 3 ), with the latter more stabilized with increasing Tris concentration. In mixed metal solutions without Tris at 25 °C where Fe:Ni or Fe:Co is 2:1, Fe increases the rates of Ni or Co carbonate precipitation. However, with increasing Tris concentration the presence of Ni or Co inhibits Fe carbonate precipitation. At 80 °C without Tris, Ni or Co substitute into the iron chukanovite (Fe 2 CO 3 (OH) 2 ) lattice, increasing Ni or Co carbonate precipitation rates. Increasing Tris concentration only slightly inhibits Fe and Co precipitation, but slows Ni precipitation up to 10 times, with Fe progressively partitioning into more pure carbonate phases with distinct crystalline morphologies. These findings suggest bidentate amine-bearing ligands may be effective at Ni and Co recovery during carbon mineralization of Fe-bearing ultramafic deposits at relatively low temperatures and slightly alkaline pH.

54 ENVIRONMENTAL SCIENCES↗

Recovery and Recrystallization Behavior of Nb-Containing Fe-Cr-Al Alloys

Nuclear-grade wrought Fe-Cr-Al alloys are currently under development as promising accident-tolerant fuel cladding materials for light water reactors (LWRs) due to their superior oxidation and corrosion resistance in high temperature steam environments when compared with current commercial Zr-based alloys. Sufficient amounts of Cr and Al additions in Fe-Cr-Al alloys provide the improved surface protection effects at both the service temperature and elevated temperatures in the accident case scenario. Minor alloying additions (such as Nb in the current study) also promote the second-phase precipitates to strengthen the alloys; e.g. sub-micron size Fe{sub 2}Nb-type Laves phase precipitates are likely to disperse at both inter- and trans-granular in BCC-Fe matrix after applying proper heat treatments. In LWRs, a seamless tube product is required for the fuel cladding which typically has ∼ 4 m length with an outside diameter of ∼ 10 mm and a wall thickness of less than 0.5 mm, and it imposes considerable challenges for tube fabrication process (e.g. tube drawing) of Fe-Cr-Al alloys. Research has been performed to achieve a balance between high-temperature performance and tube fabricability in newly developed Fe-Cr-Al alloys. BCC-Fe materials with Cr and Al additions typically suffer from poor ductility because of relatively high ductile-brittle transition temperature. In this sense, the microstructural stability of refined grain or subgrain structure, even at high temperature, is critical to maintain the deformability of the alloys during tube fabrication process, as well as sufficient mechanical properties at service condition. In this study, the recovery and recrystallization behaviors of Nb-containing Fe-Cr-Al alloys are studied. A specific focus was to evaluate the stability of the subgrain structure of the deformed Fe-Cr-Al alloys, and seek optimized processing parameters for seamless tube fabrication. The present results clearly demonstrated that the Nb addition stabilizes the refined subgrain microstructures of Fe-Cr-Al alloys below 700 deg. C due to Laves phase precipitations along sub-boundaries when compared with the Nb-free alloys, while maintaining sufficient strengths needed for fuel cladding in LWRs. At the same time, the results also showed that Nb-containing alloys can be softened through suitable annealing to improve the processability of tube drawing process. Detailed characterization efforts of subgrains and Laves phase precipitates are currently in progress. Completion of this work will deepen the understanding of the recovery and recrystallized behavior of Nb-containing Fe-Cr-Al alloys and provide guidelines to tube drawing process in the alloys. (authors)

36 MATERIALS SCIENCE↗

Properties of La 0.7 Ca 0.3 MnO 3 under extreme tensile strain

The complex phase diagram of manganites with simultaneously active spin, charge, orbital, and lattice degrees of freedom continues providing surprises. In a recent groundbreaking experiment, membranes of the perovskite manganite La 0.7 Ca 0.3 MnO 3 (LCMO) deposited on a flexible polymer layer were strained up to 8% [S. S. Hong et al., Science 368, 71 (2020)], much more than achieved by regular strain induced by a rigid substrate. By increasing this strain, a metal-insulator transition was reported. Here we reproduce the results of the experiments using Monte Carlo simulations of the two-orbital double-exchange model including Jahn-Teller distortions at hole density x=1/3. The full phase diagram with varying temperature and Jahn-Teller coupling λ is presented. When the bandwidth W of mobile electrons is reduced, thus when the effective Jahn-Teller coupling λ/W is increased, a metal-insulator transition is found in our simulations, between a ferromagnetic metallic state with uniform charge distribution and an insulator with diagonal charge stripes that retains its ferromagnetic character. In between the hole-rich diagonals, staggered orbital order occurs. We also report resistivity and magnetization measurements alongside with spin correlations and charge structure factors. Our overall conclusions are in agreement with the recent experimental and density functional theory results by Hong et al., and we confirm much earlier ground state predictions of striped ferromagnetic order using energy optimization techniques by T. Hotta et al. [Phys. Rev. Lett. 86, 4922 (2001)]. The experimental observation of one of the states predicted by theory suggests that diagonal stripes could be achieved at other hole densities as well, such as x=1/4, if LCMO membranes with that hole doping were subject to similar strains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low temperature dielectric and impedance studies on magnetoelectric Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} ceramic

The structural, microstructural, low temperature dielectric and impedance properties of Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} (PFN) ceramic prepared by single step solid-state reaction method have been investigated. Processing parameters such as calcination, sintering temperature and sintering durations were optimized to get better dielectric properties. It was found that the above ceramics sintered at 1050 °C for 4 hr exhibited single phase, maximum density and uniform microstructure. X-ray diffraction (XRD) and neutron diffraction (ND) reveals that the system exhibit single phase without any kind of secondary phases at room temperature (RT) with monoclinic crystal structure (Cm). Surface morphology of the compounds was studied by Scanning electron microscope (SEM). Impedance spectroscopy is used to study the electrical behaviour of PFN in the frequency range from 100Hz to 1MHz and in the temperature range from 120 to 293 K. The frequency-dependent electrical data are analyzed by impedance formalisms. The complex impedance shows the relaxation (conduction) mechanism in the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of extended strain fields on point defect phonon scattering in thermoelectric materials

The design of thermoelectric materials often involves the integration of point defects (alloying) as a route to reduce the lattice thermal conductivity. Classically, the point defect scattering strength follows from simple considerations such as mass contrast and the presence of induced strain fields (e.g. radius contrast, coordination changes). While the mass contrast can be easily calculated, the associated strain fields induced by defect chemistry are not readily predicted and are poorly understood. In this work, we use classical and first principles calculations to provide insight into the strain field component of phonon scattering from isoelectronic point defects. Our results also integrate experimental measurements on bulk samples of SnSe and associated alloys with S, Te, Ge, Sr and Ba. These efforts highlight that the strength and extent of the resulting strain field depends strongly on defect chemistry. Strain fields can have a profound impact on the local structure. For example, in alloys containing Ba, the strain fields have significant spatial extent (1 nm in diameter) and produce large shifts in the atomic equilibrium positions (up to 0.5 A). Such chemical complexity suggests that computational assessment of point defects for thermal conductivity depression should be hindered. However, in this work, we present and verify several computational descriptors that correlate well with the experimentally measured strain fields. Furthermore, these descriptors are conceptually transparent and computationally inexpensive, allowing computation to provide a pivotal role in the screening of effective alloys. The further development of point defect engineering could complement or replace nanostructuring when optimizing the thermal conductivity, offering the benefits of thermodynamic stability, and providing more clearly defined defect chemistry.

30 DIRECT ENERGY CONVERSION↗

Randomized Algorithms for Scientific Computing (RASC)

Randomized algorithms have propelled advances in artificial intelligence (AI) and represent a foundational research area in advancing AI for Science. Future advancements in DOE Office of Science priority areas such as climate science, astrophysics, fusion, advanced materials, combustion, and quantum computing all require randomized algorithms for surmounting challenges of complexity, robustness, and scalability. Advances in data collection and numerical simulation have changed the dynamics of scientific research and motivate the need for randomized algorithms. For instance, advances in imaging technologies such as X-ray ptychography, electron microscopy, electron energy loss spectroscopy, or adaptive optics lattice light-sheet microscopy collect hyperspectral imaging and scattering data in terabytes, at breakneck speed enabled by state-of-the-art detectors. The data collection is exceptionally fast compared with its analysis. Likewise, advances in high-performance architectures have made exascale computing a reality and changed the economies of scientific computing in the process. Floating-point operations that create data are essentially free in comparison with data movement. Thus far, most approaches have focused on creating faster hardware. Ironically, this faster hardware has exacerbated the problem by making data still easier to create. Under such an onslaught, scientists often resort to heuristic deterministic sampling schemes (e.g., low-precision arithmetic, sampling every nth element) and sacrifice potentially valuable accuracy. Dramatically better results can be achieved via randomized algorithms, reducing the data size as much as or more than naive deterministic subsampling can achieve, while retaining the high accuracy of computing on the full data set. By randomized algorithms we mean those algorithms that employ some form of randomness in internal algorithmic decisions to accelerate time to solution, increase scalability, or improve reliability. Examples include matrix sketching for solving large-scale least-squares problems (see Figure 1) and stochastic gradient descent for training machine learning models. We are not recommending heuristic methods but rather randomized algorithms that have certificates of correctness and probabilistic guarantees of optimality and near-optimality. Such approaches can be useful beyond acceleration, for example, in understanding how to avoid measure zero worst-case scenarios that plague methods such as QR matrix factorization.

97 MATHEMATICS AND COMPUTING↗

Cooperative Education

Los Alamos National Laboratory (LANL) is a multidisciplinary national laboratory that conducts research and development in national security, engineering, materials science, computational modeling, and advanced manufacturing. The laboratory develops innovative technologies to address complex scientific and engineering challenges. This project focuses on the development and evaluation of high-performance absorbing structures through computational design, simulation, and engineering analysis. Absorbing structures are used in applications where damage mitigation, structural protection, and material efficiency are critical performance requirements. The increasing demand for lightweight, high-strength, and highly efficient structural systems has created a need for improved design methodologies capable of maximizing absorption while minimizing weight and material usage. The project utilizes advanced engineering software, including 3D CAD software and FEA, to generate and optimize structural concepts. Computational simulations are performed to evaluate structural behavior under loading conditions, while mathematical analyses are conducted using Python-based tools as well as established analytical equations from material and structural mechanics. The project benefits LANL by supporting the development of advanced design methodologies and improving the understanding of material and structural performance. During the internship term, a significant portion of the design development, simulation, and data analysis activities will be completed. Success of the project depends on collaboration among engineering mentors and technical staff members. Work will be conducted at Los Alamos National Laboratory using laboratory computing resources and engineering software.

42 ENGINEERING↗

Effects of Particle Diameter and Coke Layer Thickness on Solid Flow and Stress Distribution in BF by 3D Discrete Element Method

In order to reduce ironmaking-related CO{sub 2} emissions, hydrogen-enriched blast furnace (BF) operation is currently under development. In hydrogen-enriched BF operation, coke layer thickness can be decreased to reduce CO{sub 2} emissions. However, BFs operating with thin coke layers may experience instability or discontinuous phenomena such as particle slip and gas channeling problems, so it is important to optimize the particle diameter and coke layer thickness for optimal BF operation. In this study, the effects of particle diameter and coke layer thickness on the solid flow and stress distribution in a BF were analyzed using a three-dimensional discrete element method. Furthermore, the effects of particle diameter and coke layer thickness on the burden layer stabilities, particle velocities, and particle stress distributions have been investigated. The results show that decreasing the coke layer thickness caused instability owing to the mixing of the coke and ore layers in the BF-cohesive zone and slight increases in both the average particle velocities and the average normal particle stress magnitudes. In addition, the average particle velocities and average normal particle stresses were higher for the smaller particles than for the larger ones during the simulations.

36 MATERIALS SCIENCE↗

Optimization of Interlayer/CrWN Bilayer Films Fabricated and Monitored under Shewhart Control

Chromium tungsten nitride (CrWN) films were deposited onto SUS 304 stainless steel, cutter inserts and glass substrates using direct current reactive magnetron sputtering, with pure W and Cr metal targets. The deposition parameters for the interlayer (W and WN) with multiple qualities were optimized using the gray Taguchi method. The microstructure of these coatings was determined using x-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and transmission electron microscopy. The results showed that the mechanical properties of bilayer samples with an interlayer of WN nitride film are superior to those with a W metal interlayer. Moreover, increasing the N{sub 2}/(N{sub 2} + Ar) flow ratio and working pressure enhanced the microhardness and the elastic recovery for coatings with an interlayer/CrWN bilayer. Dry milling tests also showed that bilayer film coatings have better mechanical performance. This increase in multiple performance characteristics is attributed to a bilayer that is manufactured using the gray Taguchi method. Control charts, which are powerful tools and widely used, were employed to monitor and ensure high-quality fabrication of the interlayer/CrWN bilayer and to show the coating processes to be stable and well regulated.

36 MATERIALS SCIENCE↗

Vibrational spectroscopic, structural and nonlinear optical activity studies on 2-amino-3-chloro-5-trifluoromethyl pyridine: A DFT approach

The conformational analysis was carried out for 2-amino-3-chloro-5-trifluoromethylpyridine using potential energy surface (PES) scan and the most stable optimized conformer was predicted. The theoretical vibrational frequencies were calculated for the optimized geometry using DFT/B3LYP cc-pVQZ basis set by Gaussian 09 Program. The vibrational frequencies were assigned on the basis of potential energy distribution calculation using VEDA 4.0 program package. The Mulliken atomic charge values were calculated. In the Frontier molecular orbitals analysis, the molecular reactivity, kinetic stability, intermolecular charge transfer studies and the calculation of ionization energy, electron affinity, global hardness, chemical potential, electrophilicity index and softness of the molecule were carried out. The nonlinear optical (NLO) activity was studied and the first order hyperpolarizability value was computed, which was 3.48 times greater than the urea. The natural bond orbital analysis was also performed to confirm the NLO activity of the molecule. Hence, the ACTP molecule is a promising candidate for NLO materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High energy electron diffraction instrument with tunable camera length

Ultrafast electron diffraction (UED) stands as a powerful technique for real-time observation of structural dynamics at the atomic level. In recent years, the use of MeV electrons from radio frequency guns has been widely adopted to take advantage of the relativistic suppression of the space charge effects that otherwise limit the temporal resolution of the technique. Nevertheless, there is not a clear choice for the optimal energy for a UED instrument. Scaling to beam energies higher than a few MeV does pose significant technical challenges, mainly related to the inherent increase in diffraction camera length associated with the smaller Bragg angles. In this study, we report a solution by using a compact post-sample magnetic optical system to magnify the diffraction pattern from a crystal Au sample illuminated by an 8.2 MeV electron beam. Our method employs, as one of the lenses of the optical system, a triplet of compact, high field gradients (>500 T/m), small-gap (3.5 mm) Halbach permanent magnet quadrupoles. Shifting the relative position of the quadrupoles, we demonstrate tuning the magnification by more than a factor of two, a 6× improvement in camera length, and reciprocal space resolution better than 0.1 Å –1 in agreement with beam transport simulations.

47 OTHER INSTRUMENTATION↗

Synthesis and structural characterization of the Zintl phases Na{sub 3}Ca{sub 3}TrPn{sub 4}, Na{sub 3}Sr{sub 3}TrPn{sub 4}, and Na{sub 3}Eu{sub 3}TrPn{sub 4} (Tr=Al, Ga, In; Pn=P, As, Sb)

15 new quaternary Zintl phases have been synthesized by solid-state reactions from the respective elements, and their structures have been determined by single-crystal X-ray diffraction. Na{sub 3}E{sub 3}TrPn{sub 4} (E=Ca, Sr, Eu; Tr=Al, Ga, In; Pn=P, As, Sb) crystallize in the hexagonal crystal system with the non-centrosymmetric space group P6{sub 3}mc (No. 186). The structure represents a variant of the K{sub 6}HgS{sub 4} structure type (Pearson index hP22) and features [TrPn{sub 4}]{sup 9–} tetrahedral units, surrounded by Na{sup +} and Ca{sup 2+}, Sr{sup 2+}, Eu{sup 2+} cations. The nominal formula rationalization [Na{sup +}]{sub 3}[E{sup 2+}]{sub 3}[TrPn{sub 4}]{sup 9–} follows the octet rule, suggesting closed-shell configurations for all atoms and intrinsic semiconducting behavior. However, structure refinements for several members hint at disorder and mixing of cations that potentially counteract the optimal valence electron count. - Graphical abstract: The hexagonal, non-centrosymmetric structure of Na{sub 3}E{sub 3}TrPn{sub 4} (E=Ca, Sr, Eu; Tr=Al, Ga, In; Pn=P, As, Sb) features [TrPn{sub 4}]{sup 9–} tetrahedral units, surrounded by Na{sup +} and Ca{sup 2+}, Sr{sup 2+}, Eu{sup 2+} cations. - Highlights: • 15 quaternary phosphides, arsenides, and antimonides are synthesized and structurally characterized. • The structure is a variant of the hexagonal K{sub 6}HgS{sub 4}-type, with distinctive pattern for the cations. • Occupational and/or positional disorder of yet unknown origin exists for some members of the series.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗