Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Numerical Investigation of the Effect of Rolling on the Localized Stress and Strain Induction for Wire + Arc Additive Manufactured Structures

Cold rolling can be used in-process or post-process to improve microstructure, mechanical properties and residual stress in directed-energy-deposition techniques, such as the high deposition rate wire + arc additive manufacturing (WAAM) process. Finite element simulations of the rolling process are employed to investigate the effect of rolling parameters, in particular rolling load and roller profile radius on the residual stress field as well as plastic strain distribution for the profiled roller. The results show the response to rolling of commonly used structural metals in WAAM, i.e., AA2319, S335JR steel and Ti-6Al-4V, taking into account the presence of residual stresses. The rolling load leads to changes in the location and the maximum value of the compressive residual stresses, as well as the depth of the compressive residual stresses. However, the roller profile radius only changes the maximum value of these compressive residual stresses. Changing the rolling load influences the equivalent plastic strain close to the top surface of the wall as well as in deeper areas, whereas the influence of the roller profile radius is negligible. The plastic strain distribution is virtually unaffected by the initial residual stresses prior to rolling. Finally, design curves were generated from the simulations for different materials, suggesting ideal rolling load and roller profile combinations for microstructural improvement requiring certain plastic strains at a specific depth of the additive structure.

36 MATERIALS SCIENCE↗

Solid oxide fuel cell electrolytes produced by a combination of suspension plasma spray and very low pressure plasma spray.

Plasma spray coating techniques allow unique control of electrolyte microstructures and properties as well as facilitating deposition on complex surfaces. This can enable significantly improved solid oxide fuel cells (SOFCs), including non-planar designs. SOFCs are promising because they directly convert the oxidization of fuel into electrical energy. However, electrolytes deposited using conventional plasma spray are porous and often greater than 50 microns thick. One solution to form dense, thin electrolytes of ideal composition for SOFCs is to combine suspension plasma spray (SPS) with very low pressure plasma spray (VLPPS). Increased compositional control is achieved due to dissolved dopant compounds in the suspension that are incorporated into the coating during plasma spraying. Thus, it is possible to change the chemistry of the feed stock during deposition. In the work reported, suspensions of sub-micron diameter 8 mol.% Y2O3-ZrO2 (YSZ) powders were sprayed on NiO-YSZ anodes at Sandia National Laboratories (SNL) Thermal Spray Research Laboratory (TSRL). These coatings were compared to the same suspensions doped with scandium nitrate at 3 to 8 mol%. The pressure in the chamber was 2.4 torr and the plasma was formed from a combination of argon and hydrogen gases. The resultant electrolytes were well adhered to the anode substrates and were approximately 10 microns thick. The microstructure of the resultant electrolytes will be reported as well as the electrolyte performance as part of a SOFC system via potentiodynamic testing and impedance spectroscopy.

08 HYDROGEN↗

Process and feedstock driven microstructure for laser powder bed fusion of 316L stainless steel

Here in the pursuit of improving additively manufactured (AM) component quality and reliability, fine-tuning critical process parameters such as laser power and scan speed is a great first step toward limiting defect formation and optimizing the microstructure. However, the synergistic effects between these process parameters, layer thickness, and feedstock attributes (e.g. powder size distribution) on part characteristics such as microstructure, density, hardness, and surface roughness are not as well-studied. In this work, we investigate 316L stainless steel density cubes built via laser powder bed fusion (L-PBF), emphasizing the significant microstructural changes that occur due to altering the volumetric energy density (VED) via laser power, scan speed, and layer thickness changes, coupled with different starting powder size distributions. This study demonstrates that there is not one ideal process set and powder size distribution for each machine. Instead, there are several combinations or feedstock/process parameter ‘recipes’ to achieve similar goals. This study also establishes that for equivalent VEDs, changing powder size can significantly alter part density, GND density, and hardness. Through proper parameter and feedstock control, part attributes such as density, grain size, texture, dislocation density, hardness, and surface roughness can be customized, thereby creating multiple high-performance regions in the AM process space.

316L stainless steel↗

Mechanical property degradation of high crystalline SiC fiber–reinforced SiC matrix composite neutron irradiated to ~100 displacements per atom

For the development of silicon carbide (SiC) materials for next-generation nuclear structural applications, degradation of material properties under intense neutron irradiation is a critical feasibility issue. This paper evaluated the mechanical properties and microstructure of a chemical vapor infiltrated SiC matrix composite, reinforced with a multi-layer SiC/pyrolytic carbon–coated Hi-Nicalon TM Type S SiC fiber, following neutron irradiation at 319 and 629 °C to ~100 displacements per atom. Both the proportional limit stress and ultimate flexural strength were significantly degraded as a result of irradiation at both temperatures. After irradiation at 319 °C, the quasi-ductile fracture behavior of the nonirradiated composite became brittle, a result that was explained by a loss of functionality of the fiber/matrix interface associated with the disappearance of the interphase due to irradiation. Finally, the specimens irradiated at 629 °C showed increased apparent failure strain because the fiber/matrix interphase was weakened by irradiation-induced partial debonding.

36 MATERIALS SCIENCE↗

Residual Stress Characterization of Al/SiC Nanoscale Multilayers using X-ray

Nanolayered composites are used in a variety of applications such as wear resistant coatings, thermal barrier coatings, optical and magnetic thin films, and biological coatings. Residual stresses produced in these materials during processing play an important role in controlling their microstructure and properties. In this paper, we have studied the residual stresses in model metal-ceramic Al/SiC nanoscale multilayers produced by physical vapor deposition (magnetron sputtering). X-ray synchrotron radiation was used to measure stresses in the multilayers using the sin{sup 2} {psi} technique. The stresses were evaluated as a function of layer thicknesses of Al and SiC and also as a function of the number of layers. The stress state of Al in the multilayer was largely compressive, compared to single layer Al stresses. This is attributed to a peening mechanism due to bombardment of the Al layers by SiC and Ar neutrals during deposition. The stress evolution was numerically modeled by a simplified peening process to qualitatively explain the Al thickness-dependent residual stresses.

36 MATERIALS SCIENCE↗

Development of a mechanistic thermal aging model for Grade 91

This report provides a summary on understanding and predicting the effects of long-term thermal aging on microstructure and tensile properties of G91 to corroborate the ASME Code rules in strength reduction due to elevated temperature service. The research is to support the design and long-term operation of G91 structural components in sodium-cooled fast reactors (SFRs). The report is a Level 2 deliverable in FY18 (M2NT-18AN050502061), under the Work Package NT-18AN05050206, “G91 Code Extension Testing” performed by the Argonne National Laboratory (ANL), as part of the Advanced Materials Development Program for Fast Reactors. The thermal aging study of G91 involves three types of thermally-aged specimens: (1) specimens machined from two heats of G91, G91-H1 and H30176 that have been tested for the Advanced Materials Development Programs in the past years. These specimens were aged at 550, 600, and 650°C for times up to ~64,000 h; (2) specimens fabricated from the heads of the archived crept specimens (13 in total) of six heats of G91, H5349, H30394, H30383, H10148, H30176. These specimens were aged at 427 - 538°C and for times up to 132,647 h; (3) specimens made from a tube removed from the Kingston coal-fired power plant after exposure for 155,000 h at 550°C. These three sets of specimens provide a comprehensive data set for understanding and predicting the effect of long-term thermal aging on microstructure and tensile properties of G91. Microstructural analysis of the thermally-aged G91 revealed that thermal aging causes significant microstructural changes: (1) the tempered martensite formed during tempering is unstable, and suffers significant recovery during aging, manifested by an increase in subgrain width, a decrease in subgrain length, and a decrease in subgrain aspect ratio (i.e. subgrains become more equiaxed) as the aging temperature and time increase. The subgrain recovery is facilitated by the reduction of dislocation density within subgrains; (2) M23C6 carbides in the as-received G91 are distributed along grain and subgrain boundaries and play an important role as pinning obstacles against subgrain coarsening. M23C6 carbides coarsen during aging, and the coarsening of M23C6 carbides reduces the pinning force on the boundaries; (3) MX carbonitrides in the as-received G91 are distributed uniformly within subgrains, providing the precipitation hardening effect. They coarsen with increasing aging temperature and time, but the coarsening rate is low; (3) a new phase, the Laves phase intermetallic forms during aging. The formation of the Laves phase removes the Mo solutes from the matrix, reducing the solid solution strengthening effect. The Laves phase particles grow rapidly once they are nucleated, and they precipitate primarily along boundaries. They may have a pinning effect on boundaries, but should provide little to the alloy strength. The evolution of each microstructural constituent during thermal aging can be well described by individual microstructural models. The estimated activation energy for MX coarsening was 175 kJ/mol, equivalent to the activation energy for boundary and core diffusion in a-Fe, while the estimated activation energy for subgrain coarsening was significantly lower, ~96 kJ/mol. Thermal aging of G91 results in the reduction in the yield stress and the ultimate tensile strength but has an insignificant effect on the uniform and total elongations. The reduction in tensile strength is more pronounced as the aging temperature and time increases. The in situ tensile tests with high-energy X-rays revealed that sub-boundary strengthening plays a dominant role, and the strengthening role of M23C6 particles may be accounted for by subgrian boundary hardening, and three strengthening mechanisms can be superimposed to describe the tensile strength of G91: subgrain boundary hardening, MX precipitation hardening, and Mo solid solution strengthening. A microstructure – strength model was establ

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Influence of inserted Mo layer on the thermal stability of perpendicularly magnetized Ta/Mo/Co{sub 20}Fe{sub 60}B{sub 20}/MgO/Ta films

We studied the thermal stability of perpendicular magnetic anisotropy (PMA) in Ta/Mo/CoFeB/MgO/Ta films with and without inserted Mo layers. In the absence of a Mo layer, the films show PMA at annealing temperatures below 300 °C. On the other hand, the insertion of a Mo layer preserves PMA at annealing temperatures of up to 500 °C; however, a higher annealing temperature leads to the collapse of PMA. X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTEM) were used to study the microstructure of the films to understand the deterioration of PMA. The XPS results show that the segregation of Ta is partly suppressed by inserting a Mo layer. Once inserted, Mo does not remain at the interface of Ta and CoFeB but migrates to the surface of the films. The HRTEM results show that the crystallization of the MgO (001) texture is improved owing to the higher annealing temperature of the Mo inserted sample. A smooth and clear CoFeB/MgO interface is evident. The inserted Mo layer not only helps to obtain sharper and smoother interfaces but also contributes to the crystallization after the higher annealing temperature of films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In-situ investigation of stress-induced martensitic transformation in Ti–Nb binary alloys with low Young's modulus [In-situ high-energy X-ray diffraction investigation on stress-induced martensitic transformation in Ti-Nb binary alloys]

Microstructure evolution, mechanical behaviors of cold rolled Ti-Nb alloys with different Nb contents subjected to different heat treatments were investigated. Here, optical microstructure and phase compositions of Ti-Nb alloys were characterized using optical microscopy and X-ray diffractometre, while mechanical behaviors of Ti-Nb alloys were examined by using tension tests. Stress-induced martensitic transformation in a Ti-30. at%Nb binary alloy was in-situ explored by synchrotron-based high-energy X-ray diffraction (HE-XRD). The results obtained suggested that mechanical behavior of Ti-Nb alloys, especially Young's modulus was directly dependent on chemical compositions and heat treatment process. According to the results of HE-XRD, α"-V1 martensite generated prior to the formation of α"-V2 during loading and a partial reversible transformation from α"-V1 to β phase was detected while α"-V2 tranformed to β completely during unloading.

36 MATERIALS SCIENCE↗

Orientation-Dependent Surface Faceting in UO{sub 2}

The surface behavior of UO{sub 2} plays an important role throughout the lifetime of this widely-used commercial nuclear fuel, from manufacturing to waste storage. UO{sub 2} surface properties affect fuel swelling behavior by determining the morphology, size and distribution of fission gas bubbles. Additionally, UO{sub 2} surface characteristics influence fracture behavior, which is controlled by the thermodynamics of fracture surfaces. Therefore, detailed understanding of the fundamental surface behavior will help advance prediction of the fuel performance of UO{sub 2}. Due to significant anisotropy in surface tension, faceting features form after annealing in both UO{sub 2} and many other crystalline materials. Knowledge of the correlation between crystallographic orientation and surface faceting features will expand the fundamental knowledge of UO{sub 2} surface characteristics, leading to a better understanding of fission gas swelling and fracture mechanisms. Inherent characterization technique limited previous studies on the crystallographic orientation of UO{sub 2} surface facets to low Miller index surfaces in single crystal specimens. In this study, synchrotron Laue microdiffraction was utilized to examine the crystallographic orientation of grains on the coarse surface of a polycrystalline UO{sub 2} specimen. The results were then compared with the surface morphology, obtained from scanning electron microscopy (SEM), so that a general correlation between the surface faceting features and crystallographic orientation in UO{sub 2} can be established. Both the fundamental surface characteristics and the crystallographic orientation measurements obtained in this study help advance the experiment validation of MARMOT, a mesoscale multi-physics code that predicts the coevolution of microstructure and properties within reactor fuel during its lifetime in the reactor. The MARMOT code is an indispensable component of the MOOSE-BISON-MARMOT (MBM) code suite that has been developed by Idaho National Laboratory to enable next generation fuel performance modeling capability as a part of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program Fuels Product Line (FPL). In this study, the surface-faceting features of UO{sub 2} were found to be dominated by the triple-plane structure and its variants. With this knowledge, by measuring the directions of the <110> edges, the crystallographic orientation of a surface UO{sub 2} grain can be precisely deduced in most regions of the standard stereogram triangle (SST) of the surface normal. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Residual stress characterization of Al/SiC nanoscale multilayers using X-ray

Nanolayered composites are used in a variety of applications such as wear resistant coatings, thermal barrier coatings, optical and magnetic thin films, and biological coatings. Residual stresses produced in these materials during processing play an important role in controlling their microstructure and properties. In this paper, we have studied the residual stresses in model metal-ceramic Al/SiC nanoscale multilayers produced by physical vapor deposition (magnetron sputtering). X-ray synchrotron radiation was used to measure stresses in the multilayers using the sin{sup 2} {Psi} technique. The stresses were evaluated as a function of layer thicknesses of Al and SiC and also as a function of the number of layers. The stress state of Al in the multilayer was largely compressive, compared to single layer Al stresses. This is attributed to a peening mechanism due to bombardment of the Al layers by SiC and Ar neutrals during deposition. The stress evolution was numerically modeled by a simplified peening process to qualitatively explain the Al thickness-dependent residual stresses.

36 MATERIALS SCIENCE↗

Microstructure stability of ultra-fine grained magnesium alloy AZ31 processed by extrusion and equal-channel angular pressing (EX–ECAP)

Thermal stability of the ultra-fine grained (UFG) microstructure of magnesium AZ31 alloy was investigated. UFG microstructure was achieved by a combined two-step severe plastic deformation process: the extrusion (EX) and subsequent equal-channel angular pressing (ECAP). This combined process leads to refined microstructure and enhanced microhardness. Specimens with UFG microstructure were annealed isochronally at temperatures 150–500 °C for 1 h. The evolution of microstructure, mechanical properties and dislocation density was studied by electron backscatter diffraction (EBSD), microhardness measurements and positron annihilation spectroscopy (PAS). The coarsening of the fine-grained structure at higher temperatures was accompanied by a gradual decrease of the microhardness and decrease of dislocation density. Mechanism of grain growth was studied by general equation for grain growth and Arrhenius equation. Activation energies for grain growth were calculated to be 115, 33 and 164 kJ/mol in temperature ranges of 170–210 °C, 210–400 °C and 400–500 °C (443–483 K, 483–673 K and 673–773 K), respectively. - Highlights: • Microhardness of UFG AZ31 alloy decreases with increasing annealing temperature. • This fact has two reasons: dislocation annihilations and/or grain growth. • The activation energies for grain growth were calculated for all temperature ranges.

36 MATERIALS SCIENCE↗

Influence of calcium and magnesium carbonates on hydration kinetics, hydrate assemblage and microstructural development of metakaolin containing composite cements

The hydration of metakaolin composite cements containing quartz, natural limestone and dolomite rock is studied using a multi-method approach and modelling. The study demonstrates that the calcite present in limestone and dolomite rock is very reactive. Contrary, dolomite does not dissolve. Additionally to the previously reported stabilization of ettringite, the reaction of calcite introduces several changes to the mechanism of metakaolin pozzolanic reaction. Namely, the silicate and aluminate distribution among the hydrates is different. In carbonate containing samples, experimental results supported by the thermodynamic modelling suggest that the silicate mainly precipitates as low Ca/Si C-S-H and additionally the ettringite content is higher. In the case of quartz analogue, the silicates precipitate as strätlingite and C-S-H of higher Ca/Si. These changes cause lower porosity as observed by SEM-BSE and higher strength. High metakaolin reactivity results in a very dense matrix that in turn enables co-existence of phases that are thermodynamically non-compatible.

36 MATERIALS SCIENCE↗

Effect of laser power on defect, texture, and microstructure of a laser powder bed fusion processed 316L stainless steel

The effect of laser power on defect characteristics, microstructure development, constituent phases, and crystallographic texture was studied on a laser powder bed fusion (L-PBF) processed 316L stainless steel. A series of cylindrical specimens were additively manufactured as a function of laser power ranging from 380 to 200W with a fixed scan speed of 300 mm/s using a selective laser melting system. The density (in terms of count, surface area, and porosity), size (mean values of major axis length, surface area, and volume), shape (aspect ratio and sphericity), and orientation (in terms of the angle between the major axis and build direction) of macroscopic defects in as-printed L-PBF cylinders were characterized using high-resolution synchrotron x-ray computed microtomography with a 0.65μm resolution. Moreover, the changes in the preferred crystallographic orientations and constituent phases were investigated using high-energy synchrotron x-ray diffraction. Finally, the melt pool shape and grain size/orientation were analyzed using metallography. The results show that the porosity increases linearly from 0.13 to 0.88% with the decrease in laser power. However, even with the decrease in laser power by about half and corresponding seven-fold increase in porosity, the 200W case can still be considered as nearly fully dense. On the other hand, with the same decrease in the laser power, the melt pool size/shape, grain size, and texture changed significantly. In conclusion, the role of energy input in the simultaneous changes in defect properties and microstructure development will be discussed.

36 MATERIALS SCIENCE↗

Argon-ion-induced formation of nanoporous GaSb layer: Microstructure, infrared luminescence, and vibrational properties

Room temperature implantation of 60 keV Ar{sup +}-ions in GaSb to the fluences of 7 × 10{sup 16} to 3 × 10{sup 18} ions cm{sup −2} is carried out at two incidence angles, viz 0° and 60°, leading to formation of a nanoporous layer. As the ion fluence increases, patches grow on the porous layer under normal ion implantation, whereas the porous layer gradually becomes embedded under a rough top surface for oblique incidence of ions. Grazing incidence x-ray diffraction and cross-sectional transmission electron microscopy studies reveal the existence of nanocrystallites embedded in the ion-beam amorphized GaSb matrix up to the highest fluence used in our experiment. Oxidation of the nanoporous layers becomes obvious from x-ray photoelectron spectroscopy and Raman mapping. The correlation of ion-beam induced structural modification with photoluminescence signals in the infrared region has further been studied, showing defect induced emission of additional peaks near the band edge of GaSb.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The influence of pearlite fraction on the shock properties of ferrite–pearlite steel microstructures: Insight into the effect of second-phase particles

Here, the goal of this work is to investigate the effect of varying phase fractions on the overall spall strength and damage behavior of a material. Specifically, two plain carbon, ferrite–pearlite steels (1045 and A283) were subjected to spall recovery experiments to investigate the effect of pearlite fraction on spall strength and total damage. The A283 (20% pearlite) alloy exhibited a higher Hugoniot elastic limit and spall strength compared with 1045 (60% pearlite). Discontinuous and continuous yielding behaviors were observed at quasi-static and dynamic rates for A283 and 1045, respectively. The yielding behavior was connected to pearlite fraction and the prevalence of dislocation-emitting, ferrite/cementite interfaces. Postmortem characterization revealed cementite lamellae cracking within pearlite of 1045, suggesting that pearlite reduces spall strength by providing low-energy damage nucleation sites. The rate of damage growth and coalescence was similar between the two alloys; however, 1045 exhibited more continuous cracks than A283, which exhibited a greater prevalence of discrete voids.

36 MATERIALS SCIENCE↗

Fabrication of thin-walled tubes from alloy 602 CA using shear assisted processing and extrusion

Thin-walled tube is usually produced seamlessly via an expensive multi-step process or via welding of thin sheets but at reduced performance. To overcome the current process and performance inefficiencies, advanced manufacturing methods need to be investigated. In this investigation, shear assisted processing and extrusion (ShAPE) was used to fabricate thin-walled Inconel 602 tube in a single-step. Tubes measuring 0.83 m length with a 12 mm outer diameter and 1 mm wall thickness were fabricated with an average surface roughness, Ra of 1.6 µm and Rz of 15 µm. Tensile testing of tubes in the as-fabricated condition showed strength increases of 4-35% over current offerings while maintaining or improving elongation. Electron microscopy analysis revealed the recrystallized microstructure with refined inter- and intra-granular carbides. Preliminary results obtained in this investigation shows the feasibility of producing thin-wall high temperature tube in single-step via ShAPE. This achievement marks a significant step towards manufacturing larger diameter nickel alloy tubes for the U.S. Department of Energy’s Waste Treatment and Immobilization Plant.

36 MATERIALS SCIENCE↗

Performance of Nd-Fe-B Magnets Fabricated by Hot Isostatic Pressing and Low-Temperature Sintering

Magnetic properties and microstructure of Nd-Fe-B sintered magnets fabricated by hot isostatic pressing (HIP) were studied. For comparison, magnets were also fabricated by vacuum sintering. The density reached 7.58 g/cm{sup 3} for the magnets HIP-sintered at 1123 K. The density of the magnets vacuum-sintered at 1123 K was much lower, which is of about 6.92 g/cm{sup 3}. While the density of magnets vacuum-sintered at 1318 K was the same as the HIP-sintered magnets, the sintering temperature was significantly decreased to 1123 K. In addition, the average grain size decreased from 9 to 6 μm, which has enhanced coercivity. Therefore, the coercivity increased from 1067.7 to 1238.5 kA/m, which is 16% higher than the vacuum-sintered magnets. HIP is a promising method to obtain high density and high coercivity Nd-Fe-B sintered magnets.

36 MATERIALS SCIENCE↗

Crystal Plasticity Model of Reactor Pressure Vessel Embrittlement in GRIZZLY

The integrity of reactor pressure vessels (RPVs) is of utmost importance to ensure safe operation of nuclear reactors under extended lifetime. Microstructure-scale models at various length and time scales, coupled concurrently or through homogenization methods, can play a crucial role in understanding and quantifying irradiation-induced defect production, growth and their influence on mechanical behavior of RPV steels. A multi-scale approach, involving atomistic, meso- and engineering-scale models, is currently being pursued within the GRIZZLY project to understand and quantify irradiation-induced embrittlement of RPV steels. Within this framework, a dislocation-density based crystal plasticity model has been developed in GRIZZLY that captures the effect of irradiation-induced defects on the flow stress behavior and is presented in this report. The present formulation accounts for the interaction between self-interstitial loops and matrix dislocations. The model predictions have been validated with experiments and dislocation dynamics simulation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗