Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Effect of temperature on the microstructure of calcium silicate hydrate (C-S-H)

Temperature affects the properties of concrete through its effect on the hydration of cement and its associated microstructural development. This paper focuses on the modifications to C-S-H induced by isothermal curing between 5 and 60 °C. The results show that as the temperature increases (within the range studied) the C/S ratio of C-S-H changes only slightly, with a higher degree of polymerisation of silicate chains, but there is a significant decrease in its bound water content and an increase of apparent density of 25%. This increase seems to come from a different packing of C-S-H at the nanoscale. As a consequence of these changes, the microstructure of the cement paste is much coarser and porous, which explains the lower final strengths obtained by curing at elevated temperatures. -- Highlights: •C-S-H structure studied at the atomic level •Multiple analytical techniques used •Studies conducted at temperatures above and below normal temperatures.

36 MATERIALS SCIENCE↗

Distinctive microstructural features of aged sodium silicate-activated slag concretes

Electron microscopic characterisation of 7-year old alkali-activated blast-furnace slag concretes enabled the identification of distinct microstructural features, providing insight into the mechanisms by which these materials evolve over time. Backscattered electron images show the formation of Liesegang-type ring formations, suggesting that the reaction at advanced age is likely to follow an Oswald supersaturation–nucleation–depletion cycle. Segregation of Ca-rich veins, related to the formation of Ca(OH){sub 2}, is observed in microcracked regions due to the ongoing reaction between the pore solution and available calcium from remnant slag grains. A highly dense and uniform interfacial transition zone is identified between siliceous aggregate particles and the alkali activated slag binders, across the concretes assessed. Alkali-activated slag concretes retain a highly dense and stable microstructure at advanced ages, where any microcracks induced at early ages seem to be partially closing, and the remnant slag grains continue reacting.

36 MATERIALS SCIENCE↗

Link between microstructure and tritiated water diffusivity in mortars: Impact of aggregates

The present study aims to investigate the influence of microstructure, particularly the effect of aggregates content and interfacial transition zone (ITZ), on tritiated water (HTO) diffusivity in mortars. To this end, three different series of mortars were prepared and HTO diffusion tests were conducted. Variables are water-to-cement ratio, sand volume fractions, and particle size distribution. In parallel, the microstructure of these materials was characterized by water porosimetry, mercury porosimetry, and by backscattered electron microscopy associated to images analysis. It was observed that at low sand content (0%–50%), diffusion properties of mortars are dominated by aggregates dilution effect. Beyond 50% of standard sand, other effects related to the large number of sand grains appear, such as air voids and porous areas mainly due to the difficulty of obtaining well-compacted materials.

36 MATERIALS SCIENCE↗

The influence of substrate moisture preparation on bond strength of concrete overlays and the microstructure of the OTZ

The influence of substrate moisture preparation on the direct shear bond strength of composite substrate-overlay specimens was evaluated. The substrate surface was exposed to four different moisture conditions prior to overlay application. A quantitative analysis of backscattered electron images of the microstructure of the overlay transition zone was carried out to quantify its properties along the interface and help analyse the results of the shear bond testing. The results show that pre-wetting the substrate surface prior to application of the overlay provides no added benefit towards increasing the bond strength and may in some cases reduce bond strength significantly. The microstructural investigations confirmed that pre-saturated substrates increase the w/c ratio and the porosity in the overlay transition zone (OTZ), which was found to have a thickness of about 100 μm. The OTZ in overlays cast on dry substrate surfaces had lower porosity and an increased amount of anhydrous cement.

36 MATERIALS SCIENCE↗

Effect of the hydration temperature on the microstructure of Class G cement: C-S-H composition and density

Curing temperature has a significant influence on cement paste microstructure and the properties of its principal hydrate C-S-H. In this paper, the effect of the hydration temperature in the range of 7 °C to 90 °C on the microstructure of a class G oil-well cement is studied. This is done by combining various experimental methods, including X-ray diffraction associated with the Rietveld analysis, thermo-gravimetric analysis, mercury intrusion porosimetry and porosity evaluation by drying. The experimental results show an increase of the capillary porosity and a decrease of the gel porosity by increasing the hydration temperature. This is attributed to a decrease of the C-S-H intrinsic porosity and a corresponding increase of the C-S-H density for higher curing temperatures. The experimental results are used in a simple analysis method to evaluate the density of C-S-H, as well as its C/S ratio and H/S ratio in dry and saturated conditions. The evaluated C-S-H density varies from 1.88 g/cm{sup 3} at 7 °C to 2.10 g/cm{sup 3} at 90 °C. The results also show a decrease of molar C/S ratio with increasing hydration temperature from 1.93 at 7 °C to 1.71 at 90 °C and of the H/S ratio from 5.1 at 7 °C to 2.66 at 90 °C.

36 MATERIALS SCIENCE↗

Influence of fly ash and metakaolin on the microstructure and compressive strength of magnesium potassium phosphate cement paste

The influences of fly ash and metakaolin added as substitutions (by up to 50 wt%) of magnesium potassium phosphate cement (MKPC) on the microstructures and compressive strengths of the MKPC pastes were investigated. The results indicate that the aluminosilicate fractions of both fly ash and metakaolin are involved in the acid-base reaction of MKPC system, leading to a preferential formation of irregular crystalline struvite-K incorporated with Al and Si elements and/or amorphous aluminosilicate phosphate products. Metakaolin is more reactive than fly ash in the MKPC system. For the same addition dosage, the MKPC pastes containing metakaolin exhibit higher compressive strengths than the pastes containing fly ash. This is attributed to the formation of more highly reinforced microstructures and denser interfaces between the metakaolin particle and hydration products (e.g. struvite-K) in the MKPC paste containing metakaolin. Addition of 30 wt% metakaolin increases the compressive strengths of MKPC pastes at all test ages.

36 MATERIALS SCIENCE↗

Mineralogical and microstructural alterations in a portland cement paste after an accelerated decalcification process

Cement paste leaching and concomitant decalcification is a common cause of concrete structure deterioration. Such alterations entail microstructural changes that condition concrete durability. This study analysed those changes in cement pastes exposed to accelerated decalcification, layer-by-layer, from the surface in contact with the leaching agent, 6 M NH{sub 4}NO{sub 3,} to the unaltered area. The microstructural changes were analysed with BSEM, MIP and BET whilst the mineralogical and nanostructural alterations in each layer were assessed with XRD, FTIR, {sup 29}Si and {sup 27}Al MAS NMR and BSD. Decalcification affected not only portlandite and CSH gel, but also the anhydrous clinker and ettringite, inducing major micro- and nano-structural changes, particularly in the two layers closest to the leaching agent. CSH gel decalcification was more intense in the outer layers where long chain gels co-existed with silicon rich gels. BDS, in turn, revealed differences between the amount of bound water in the surface interfacing with the leaching agent and in the leaching front. More specifically, larger numbers of water molecules were tightly bound to silanol groups in the outer, whereas hydroxyl group distribution was more orderly in the inner layers.

36 MATERIALS SCIENCE↗

GeoMicro3D: A novel numerical model for simulating the reaction process and microstructure formation of alkali-activated slag

Highlights: • The GeoMicro3D model was innovatively developed for simulating the reaction process and microstructure formation of AAS. • In GeoMicro3D, the dissolution of slag and reactions of aqueous ions are fundamentally described in the local lattice cell. • A novel approach is proposed to speed up the nucleation simulations. • GeoMicro3D was implemented and verified with the relevant experimental data and thermodynamic calculation results. For the first time, this study developed a novel model, named GeoMicro3D, to simulate the reaction process and microstructure formation of alkali-activated slag. The GeoMicro3D model consists of four modules that are designed to simulate, respectively: (i) the initial spatial distribution of real-shape slag particles in alkaline activator, (ii) the dissolution of slag and diffusion of ions via the transition state theory and lattice Boltzmann method, respectively, (iii) the spatial distribution of reaction products using a nucleation probability theory, and (iv) the chemical reactions with thermodynamic modelling. Afterwards the GeoMicro3D model was implemented and verified. The simulation results were discussed and compared with the relevant experimental data and thermodynamic calculation results using GEMS. A good agreement was found in the comparisons, showing the strong simulation capability of GeoMicro3D.

36 MATERIALS SCIENCE↗

Influence of supplementary cementitious materials on microstructure and transport properties of spacer-concrete interface

Reinforcement spacers are a critical component of concrete structures. Their presence affects microstructure and transport properties of concrete cover though this is not widely appreciated. This paper presents the first study to determine whether the negative effects of spacers can be mitigated through the use of supplementary cementitious materials such as silica fume, fly ash and blast-furnace slag. Concrete samples (>200) with different spacers, binders, curing and drying regimes were prepared and tested for diffusion, permeation, absorption, electrical conductivity, carbonation and microstructure. It was found that spacers increase all transport properties, the extent depending on type of spacer, drying regime and transport mechanism. The spacer-concrete interface is weak, porous and micro-cracked, and this lowers the resistance of concrete to ingress of aggressive agents. The beneficial effects of SCMs (strength enhancement and densification) and prolonged curing (120-day) are insufficient to overcome the negative effects of spacers. Implications for durability are discussed.

36 MATERIALS SCIENCE↗

Microstructure Based Modeling of β Phase Influence on Mechanical Response of Cast AM Series Mg Alloys

Magnesium alloys have become popular alternatives to aluminums and steels for the purpose of vehicle light-weighting. However, Mg alloys are hindered from wider application due to limited ductility as well as poor creep and corrosion performance. Understanding the impact of microstructural features on bulk response is key to improving Mg alloys for more widespread use and for moving towards truly predicting modeling capabilities. This study focuses on modeling the intrinsic features, particularly volume fraction and morphology of beta phase present, of cast Mg alloy microstructure and quantifying their impact on bulk performance. Computational results are compared to experimental measurements of cast plates of Mg alloy with varying aluminum content.

Cast Magnesium alloys↗

Investigation of grain-scale microstructural variability in tantalum using crystal plasticity-finite element simulations

In this research, a crystal plasticity-finite element (CP-FE) model is used to investigate the effects of microstructural variability at a notch tip in tantalum single crystals and polycrystals. It is shown that at the macroscopic scale, the mechanical response of single crystals is sensitive to the crystallographic orientation while the response of polycrystals shows relatively small susceptibility to it. However, at the microscopic scale, the local stress and strain fields in the vicinity of the crack tip are completely determined by the local crystallographic orientation at the crack tip for both single and polycrystalline specimens with similar mechanical field distributions. Variability in the local metrics used (maximum von Mises stress and equivalent plastic strain at 3% deformation) for 100 different realizations of polycrystals fluctuates by up to a factor of 2–7 depending on the local crystallographic texture. Comparison with experimental data shows that the CP model captures variability in stress–strain response of polycrystals that can be attributed to the grain-scale microstructural variability. In conclusion, this work provides a convenient approach to investigate fluctuations in the mechanical behavior of polycrystalline materials induced by grain morphology and crystallographic orientations.

36 MATERIALS SCIENCE↗

Microstructure modeling of nuclear structural materials: Recent progress and future directions

Modeling and simulation of microstructures are essential to understand the complex responses and behaviors of nuclear materials in extreme environments. The needs to assess the extended life operation as well as the growing interest in accelerating nuclear materials development and qualification have stimulated the use of high-fidelity multiscale models aided by empirical and ab initio data. This paper reviews the role of various models across different length and time scales in investigating irradiation effects on microstructure evolution and degradation, in particular the embrittlement caused by radiation induced or enhanced formation of nanoscale chemical heterogeneities. The strength and limitations of these models, including classical rate theories, cluster dynamics, phase-field methods, and atomistic models informed by ab initio energies, are discussed with seminal examples. Challenges regarding the lack of thermo-kinetic data and theoretical treatments considering chemical complexities and magnetic excitations, as well as the stabilizing effect by excess point defects in nuclear structural materials are presented, along with potential solutions based on ab initio informed surrogate energy models and statistical sampling by Monte Carlo simulations. Further, the review then highlights the opportunities to leverage the advantages of different methods by establishing hybrid models by shared variables or coupled codes and applications. Finally, the review concludes with forward-looking remarks on how the use of physics-based models can aid the improvement of machine-learning models of property degradation and vice versa.

36 MATERIALS SCIENCE↗

Fatigue of additive manufactured Ti-6Al-4V, Part I: The effects of powder feedstock, manufacturing, and post-process conditions on the resulting microstructure and defects

Additive manufacturing provides an appealing means to process titanium alloy parts with new levels of conformability, complexity, and weight reduction. However, due to the heating/cooling rates and heat transfer associated with directed energy source material processing, the as-built AM parts contain unique material and microstructural features. In order to confidently manufacture fatigue critical additive manufactured (AM) Ti-6Al-4V parts, a better understanding of the interrelationships between powder feedstock, AM processes, structure of the processed parts, their resulting mechanical properties, and their performance under realistic loadings is necessary. Part I of this two-part collection focuses on the powder-process-structure relationships and how powder feedstock, manufacturing, and post-processing conditions can affect the microstructure and defect features that ultimately contribute to the fatigue performance of Ti-6Al-4V parts. The material and physical phenomena inherent to the AM process of Ti-6Al-4V are discussed in detail and related to the phase composition/structure, grain morphology, surface characteristics, defect size/distribution, and post-process treatments available for AM parts. This investigation is the foundation for the structure-performance relationships that will be covered in detail in Part II.

36 MATERIALS SCIENCE↗

Gradient microstructure induced shear band constraint, delocalization, and delayed failure in CuZr nanoglasses

The mechanical properties of metallic glasses (MGs) can be significantly tuned by introducing a nanoscale glass-glass interface microstructure. Here, we design three types of Cu 64 Zr 36 MG seamless gradient microstructures by combining glassy grain sizes from 3 to 15 nm. We perform tensile loading molecular dynamics simulations on the named gradient nanoglasses to characterize their mechanical behavior. In all cases, results indicate the generation of gradient plasticity following the gradient in grain size, i.e. local plasticity increases from large to small grain size regions. Loading parallel to the gradient direction results in initial broad necking followed by catastrophic failure. In contrast, loading perpendicular to the gradient direction results in diffused shear band propagation from large to small grain size regions, delaying the generation of a dominant shear band and further delocalizing plastic deformation. In conclusion, the results demonstrate the synergistic effects generated by heterogeneous gradient designs in the mechanical behavior of metallic glasses.

36 MATERIALS SCIENCE↗

Elevated temperature microstructure evolution of a medium-entropy CrCoNi superalloy containing Al,Ti

A new medium-entropy superalloy was produced based on the compositions of equiatomic CrCoNi and Ni-base superalloy Inconel 740H. Initial alloy design was performed using Thermo-Calc. The aging response and microstructural stability were assessed following heat treatment at temperatures between 600 and 900 °C and durations up to 100 h. Aging from a fully recrystallized state resulted in negligible grain growth and produced γ’ and σ phases. The same phases were present after aging from a cold-rolled state, but partially recrystallized microstructures resulted in multi-modal size distributions and heterogeneous spatial arrangements. Finally, room temperature hardness measurements were used to correlate aging conditions with quantitative precipitate measurements and mechanical properties.

36 MATERIALS SCIENCE↗

In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation

In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗

Densification, microstructure, and mechanical properties of Mo–30W alloys fabricated from conditioned powders

Refractory alloys, such as molybdenum-based systems, are attracting growing interest for applications in extreme environments, such as in the nuclear and aerospace industries. Recent advances in sintering technologies, coupled with mechanical alloying, have enabled the tailored design of these alloys by leveraging powder characteristics to control final microstructures and mechanical properties. In this study, Mo-30W alloys were fabricated using electric field-assisted sintering (EFAS) from ball-milled powders with and without hydrogen treatment to investigate the influence of surface oxides on material properties and sintering behavior. The results revealed that samples processed from as-ball-milled powder contained a high density of oxides within the microstructure, whereas oxide presence was significantly reduced in samples fabricated from hydrogen-treated powders. Interestingly, the two powder types led to opposite trends in grain size distribution: samples from untreated powders exhibited grain refinement from sample periphery to the center, while samples from hydrogen-treated powders showed grain coarsening toward the center. This behavior is attributed to temperature gradients present during sintering due to electrical percolation pathway differences during Joule heating. The powder surface oxides may have influenced the temperature distribution and grain evolution. Microhardness profiles measured along both axial and thickness directions were consistent with the grain size distribution. Furthermore, oxide films on powder surfaces have delayed densification by hindering particle necking and atomic diffusion during sintering.

36 - MATERIALS SCIENCE↗