Search NASA⌕ Search

SEARCH · Search NASA

Results for “Padding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Development of inflatable structures for Electron Echo V

The sounding rocket experiment, Electron Echo V, was designed to carry three devices to study the neutralization effects of the rocket upon electron beams emitted into the earth's magnetosphere. One was a 500 square foot current collector screen built on a framework of inflated 'mylar' tubes. The other two were 30 foot long Langmuir probes consisting of inflated tubes with sensor pads at various intervals. These devices were designed to be deployed at an altitude of 92-118 mi (148-190 km) by compressed gas carried in the payload. The development of these large (by sounding rocket standards) inflatables and the methods of packaging and deployment are described.

Oliver, J. A.↗

Investigation of a laser Doppler velocimeter system to measure the flow field of a large scale V/STOL aircraft in ground effect

An experimental research program for measuring the flow field around a 70 percent scale V/STOL aircraft model in ground effect is described. The velocity measurements were conducted with a ground-based laser Doppler velocimeter at an outdoor test pad. The remote sensing instrumentation, experimental tests, and results of the velocity surveys are discussed. The distribution of vertical velocity in the fan jet and fountain, the radial velocity in the wall jet and the horizontal velocity along the aircraft underside are presented for different engine rpms and aircraft heights above ground. The study shows that it is feasible to use a mobile laser Doppler velocimeter to measure the flow field generated by a large scale V/STOL aircraft operating in ground effect.

Zalay, A. D.↗

Plans for West Coast STS launch capability

The layout and scope of operations of the Vandenberg AFB West Coast Launch Site for the Space Shuttle are examined. The launch site intended for the first West Coast launch in December 1983 is being constructed by the United States Air Force. Topic discussed include site/selection/management/concepts, Shuttle hardware flow and related facilities, launch pad operations, orbiter erection at SLC-6 VAFB, solid rocket booster operations, and payload ground processing. In conclusion it is noted that NASA and DOD personnel are working together to ensure that the launch site is completed on schedule at minimum cost.

Murphy, W. P.↗

Polynominal Interpolation Methods for Viscous Flow Calculations

Higher-order collocation procedures resulting in tridiagonal matrix systems are derived from polynomial spline interpolation and by Hermitian (Taylor series) finite-difference discretization. The similarities and special features of these different developments are discussed. The governing systems apply for both uniform and variable meshes. Hybrid schemes resulting from two different polynomial approximations for the first and second derivatives lead to a nonuniform mesh extension of the so-called compact or Pad? difference technique (Hermite 4). A variety of fourth-order methods are described and the Hermitian approach is extended to sixth-order (Hermite 6). The appropriate spline boundary conditions are derived for all procedures. For central finite differences, this leads to a two-point, second-order accurate generalization of the commonly used three-point end-difference formula. Solutions with several spline and Hermite procedures are presented for the boundary layer equations, with and without mass transfer, and for the incompressible viscous flow in a driven cavity. Divergence and nondivergence equations are considered for the cavity. Among the fourth-order techniques, it is shown that spline 4 has the smallest truncation error. The spline 4 procedure generally requires one-quarter the number of mesh points in a given coordinate direction as a central finite-difference calculation of equal accuracy. The Hermite 6 procedure leads to remarkably accurate boundary layer solutions.

Rubin, S. G.↗

"Densified" tiles form stronger bonds

Application of colloidal silica more than doubles bond strength of ceramic tile/substrate attachments. "Densification" process strengthens surface where tile attaches to felt strain-isolator pad, redistributing stresses and preventing failures at that point. First, isopropyl alcohol is applied to bottom tile surface. Second, aqueous mixture of cementing colloidal silica and reinforcing ball-milled silica particles is painted on tile. Finally, after drying, tile is rewaterproofed by exposure to vapors or methyltrimethoxysilane and acetic acid.

Dotts, R. L.↗

Low sidelobe level low-cost earth station antennas for the 12 GHz broadcasting satellite service

An experimental investigation of the performance of 1.22 m and 1.83 m diameter paraboloid antennas with an f/D ratio of 0.38 and using a feed developed by Kumar is reported. It is found that sidelobes below 30 dB can be obtained only if the paraboloids are relatively free of surface errors. A theoretical analysis of clam shell distortion shows that this is a limiting factor in achieving low sidelobe levels with many commercially available low cost paraboloids. The use of absorbing pads and small reflecting plates for sidelobe reduction is also considered.

Collin, R. E.↗

Nonlinear static TPS analysis

A nonlinear analysis which includes the effect of mismatch and filler bar was developed to predict the strain isolator pad reuseable surface insulation through-the-thickness interface stresses. Parametric studies were conducted for simulated shock loading on square tiles. Expected loads on an actual tile were also studied. The results indicate that when no mismatch is present, linear solutions tend to give nonconservative maximum stresses relative to the nonlinear solutions. When mismatch is present, the linear maximum stresses are only conservative at low load levels and highly nonconservative at high load levels. Although the presence of filler bar reduces maximum tensile stresses in some cases, it does not appear that the nominal dimension filler bar can reduce the nonlinear stress to a level at which the linear solution becomes conservative relative to the nonlinear solution. Moreover, on an outboard trailing edge elevon tile at descent with +20 deg flap, the linear analysis is 49% nonconservative relative to the nonlinear analysis with filler bar.

Housner, J. M.↗

Analysis of nuclear waste disposal in space, phase 3. Volume 2: Technical report

The options, reference definitions and/or requirements currently envisioned for the total nuclear waste disposal in space mission are summarized. The waste form evaluation and selection process is documented along with the physical characteristics of the iron nickel-base cermet matrix chosen for disposal of commercial and defense wastes. Safety aspects of radioisotope thermal generators, the general purpose heat source, and the Lewis Research Center concept for space disposal are assessed as well as the on-pad catastrophic accident environments for the uprated space shuttle and the heavy lift launch vehicle. The radionuclides that contribute most to long-term risk of terrestrial disposal were determined and the effects of resuspension of fallout particles from an accidental release of waste material were studied. Health effects are considered. Payload breakup and rescue technology are discussed as well as expected requirements for licensing, supporting research and technology, and safety testing.

Rice, E. E.↗

Room temperature mechanical properties of shuttle thermal protection system materials

Tests were conducted at room temperature to determine the mechanical properties and behavior of materials used for the thermal protection system of the space shuttle. The materials investigated include the LI-900 RSI tiles, the RTV-560 adhesive and the .41 cm (.16 thick) strain isolator pad (SIP). Tensile and compression cyclic loading tests were conducted on the SIP material and stress-strain curves obtained for various proof loads and load cyclic conditioning. Ultimate tensile and shear tests were conducted on the RSI, RTV, and SIP materials. The SIP material exhibits highly nonlinear stress-strain behavior, increased tangent modulus and ultimate tensile strength with increased loading rate, and large short time load relaxation and moderate creep behavior. Proof and cyclic load conditioning of the SIP results in permanent deformation of the material, hysteresis effects, and much higher tensile tangent modulus values at large strains.

Sawyer, J. W.↗

Microstructural characterization of the HRSI thermal protection system for space shuttle

Components of the space shuttle high temperature reusable surface insulation (HRSI) system were microscopically characterized, both separately and as a system, to obtain information needed for stress analysis models of the thermal protection system. A tension specimen of the HRSI system was loaded in steps and was microscopically observed at each load condition to demonstrate the tension failure mode associated with strain isolation pad (SIP) behavior. A local failure occurred which should be associated with transfer of load through transverse fibers in the SIP. Stress concentrations attributed to the SIP behavior necessitated strengthening of the HRSI by densification of the RSI at the bondline. An HRSI tile was microscopically characterized after the densification process. The densified surface layer blended into the RSI which caused a gradual change in density. The gradation in density does not appear to represent a sharp discontinuity in elastic modulus between the densified layer and the parent material.

Ransone, P. O.↗

Thermal performance of a mechanically attached ablator tile for on-orbit repair of shuttle TPS

The reusable surface insulation (RSI) material used in the shuttle thermal protection system is susceptible to damage. If any RSI tiles are damaged or lost during ascent, they must be repaired or replaced prior to entry. One approach to replacing a damaged or missing RSI tile consists of mechanically attaching a tile of ablation material in the place of the RSI tile. The thermal performance of this type of repair tile was evaluated in a simulated entry heating environment. The test specimen consisted of the ablator repair tile mechanically fastened to the strain isolation pad and surrounded by RSI tiles. The evaluation of the thermal performance was based on temperature response, surface integrity, and predicted flight performance. When the ablator tile protruded 1/8 inch above the surrounding RSI tiles, the forward facing steps caused significant inflow of hot gas down the ablator RSI joints and this inflow caused greatly increased back surface temperatures.

Thompkins, S. S.↗

Limit cycles of a flexible shaft with hydrodynamic journal bearings in unstable regimes

A symmetric 3 mass rotor supported on hydrodynamic bearings is described. An approximate method of representing finite bearings is used to calculate bearing forces. As the method sums forces from a number of independent circular lobes lemon 3 and 4 lobe bearings are taken into account. The calculations are based on an axial groove bearing. Linear analysis precedes nonlinear simulation of some unstable conditions. The demonstration of small limit cycles suggests that necessarily flexible rotors e.g., helicopter tail rotors, may be practical without either tilt pad bearings or external dampers.

Brown, R. D.↗

Instability thresholds for flexible rotors in hydrodynamic bearings

Two types of fixed pad hydrodynamic bearings (multilobe and pressure dam) were considered. Optimum and nonoptimum geometric configurations were tested. The optimum geometric configurations were determined by using a theoretical analysis and then the bearings were constructed for a flexible rotor test rig. It was found that optimizing bearings using this technique produces a 100% or greater increase in rotor stability. It is shown that this increase in rotor stability is carried out in the absence of certain types of instability mechanisms such as aerodynamic crosscoupling. However, the increase in rotor stability should greatly improve rotating machinery performance in the presence of such forces as well.

Allaire, P. E.↗

Photoelastic tests on models of thermal protection system for space shuttle orbiter

The thermal protection system (TPS) of the space shuttle orbiter vehicle, consisting of ceramic tile/adhesive/strain isolator pad/adhesive/aluminum substructure, was modeled photoelasticity. A highly sensitive photoelastic material was used in the models to show the nature of the stress-transfer between the strain isolation pad (SIP) and the ceramic tile through the RTV-adhesive layer. Isochromatic fringe patterns were obtained for models subjected to tension and combined tension and bending. Tests indicated that the load-transfer between the SIP and the photoelastic material occurred at discrete locations causing stress concentrations in the photoelastic material. Stress concentration factors of the order of 1.9 were measured, but as the observed photoelastic response was an integrated effect through the model thickness, the local stress concentration factors at the SIP/tile interface could be even higher.

Prabhakaran, R.↗

Effects of substrate deformation and sip thickness on tile/sip interface stresses for shuttle thermal protection

A nonlinear analysis was used to study the effects of substrate deformation characteristics and strain isolator pad (SIP) thickness on TILE/SIP interface stresses for the space shuttle thermal protection system. The configuration analyzed consisted of a 5.08 cm thick, 15.24 cm square tile with a 12.7 cm square SIP footprint bordered by a 1.27 cm wide filler bar and was subjected to forces and moments representative of a 20.7 kPa aerodynamic shock passing over the tile. The SIP stress deflection curves were obtained after a 69 kPa proof load and 100 cycles conditioning at 55 kPa. The TILE/SIP interface stresses increase over flat substrate values for zero to peak substrate deformation amplitudes up to 0.191 cm by up to a factor of nearly five depending on deformation amplitude, half wave length, and location. Stresses for a 0.23 cm thick SIP found to be up to 60 percent greater than for a 0.41 cm thick SIP for identical loads and substrate deformation characteristics. A simplified method was developed for approximating the substrate location which produces maximum TILE/SIP interface stresses.

Shore, C. P.↗

Segmentation, dynamic storage, and variable loading on CDC equipment

Techniques for varying the segmented load structure of a program and for varying the dynamic storage allocation, depending upon whether a batch type or interactive type run is desired, are explained and demonstrated. All changes are based on a single data input to the program. The techniques involve: code within the program to suppress scratch pad input/output (I/O) for a batch run or translate the in-core data storage area from blank common to the end-of-code+1 address of a particular segment for an interactive run; automatic editing of the segload directives prior to loading, based upon data input to the program, to vary the structure of the load for interactive and batch runs; and automatic editing of the load map to determine the initial addresses for in core data storage for an interactive run.

Tiffany, S. H.↗

Development of flexible rotor balancing criteria

Several studies in which analytical procedures were used to obtain balancing criteria for flexible rotors are described. General response data for a uniform rotor in damped flexible supports were first obtained for plain cylindrical bearings, tilting pad bearings, axial groove bearings, and partial arc bearings. These data formed the basis for the flexible rotor balance criteria presented. A procedure by which a practical rotor in bearings could be reduced to an equivalent uniform rotor was developed and tested. It was found that the equivalent rotor response always exceeded to practical rotor response by more than sixty percent for the cases tested. The equivalent rotor procedure was then tested against six practical rotor configurations for which data was available. It was found that the equivalent rotor method offered a procedure by which balance criteria could be selected for practical flexible rotors, using the charts given for the uniform rotor.

Walter, W. W.↗

KSC facilities status and planned management operations

A status report is presented on facilities and planned operations at the Kennedy Space Center with reference to Space Shuttle launch activities. The facilities are essentially complete, with all new construction and modifications to existing buildings almost finished. Some activity is still in progress at Pad A and on the Mobile Launcher due to changes in requirements but is not expected to affect the launch schedule. The installation and testing of the ground checkout equipment that will be used to test the flight hardware is now in operation. The Launch Processing System is currently supporting the development of the applications software that will perform the testing of this flight hardware.

Gray, R. H.↗