Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESISTANCE DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Improved diamond surfaces following lift-off and plasma treatments as observed by x-ray absorption spectroscopy

We have investigated the nature of the residual damage in diamond crystals following the ion implantation/graphitization ''lift-off'' process, using near-edge x-ray absorption fine structure spectroscopy and transmission electron microscopy. A defective but crystalline interface is found, which displays dense pre-edge unoccupied states and an almost complete loss of the core-level C 1s exciton signature. This residual crystalline damage is resistant to standard chemical etching, however a hydrogen plasma treatment is found to completely recover a pristine diamond surface. Analysis and removal of residual ion-induced damage is considered crucial to the performance of many diamond device architectures.

36 MATERIALS SCIENCE↗

Bilayer graphene quantum dot defined by topgates

We investigate the application of nanoscale topgates on exfoliated bilayer graphene to define quantum dot devices. At temperatures below 500 mK, the conductance underneath the grounded gates is suppressed, which we attribute to nearest neighbour hopping and strain-induced piezoelectric fields. The gate-layout can thus be used to define resistive regions by tuning into the corresponding temperature range. We use this method to define a quantum dot structure in bilayer graphene showing Coulomb blockade oscillations consistent with the gate layout.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

CuS p-type thin film characterization deposited on Ti, ITO and glass substrates using spray pyrolysis deposition (SPD) for light emitting diode (LED) application

The copper sulphide (CuS) thin films were grown with good adhesion by spray pyrolysis deposition (SPD) on Ti, ITO and glass substrates at 200 °C. The distance between nozzle and substrate is 30 cm. The composition was prepared by mixing copper chloride CuCl{sub 2}.2H{sub 2}O as a source of Cu{sup 2+} and sodium thiosulfate Na{sub 2}S{sub 2}O{sub 3}.5H{sub 2}O as a source of and S{sup 2−}. Two concentrations (0.2 and 0.4 M) were used for each CuCl{sub 2} and Na{sub 2}S{sub 2}O{sub 3} to be prepared and then sprayed (20 ml). The process was started by spraying the solution for 3 seconds and after 10 seconds the cycle was repeated until the solution was sprayed completely on the hot substrates. The structural characteristics were studied using X-ray diffraction; they showed covellite CuS hexagonal crystal structure for 0.2 M concentration, and covellite CuS hexagonal crystal structure with two small peaks of chalcocite Cu{sub 2}S hexagonal crystal structure for 0.4 M concentration. Also the surface and electrical characteristics were investigated using Field Emission Scanning Electron Microscopy (FESEM) and current source device, respectively. The surface study for the CuS thin films showed nanorods to be established for 0.2 M concentration and mix of nanorods and nanoplates for 0.4 M concentration. The electrical study showed ohmic behavior and low resistivity for these films. Hall Effect was measured for these thin films, it showed that all samples of CuS are p- type thin films and ensured that the resistivity for thin films of 0.2 M concentration was lower than that of 0.4 M concentration; and for the two concentrations CuS thin film deposited on ITO had the lowest resistivity. This leads to the result that the conductivity was high for CuS thin film deposited on ITO substrate, and the conductivity of the three thin films of 0.2 M concentration was higher than that of 0.4 M concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The use of processes evaporation and condensation to provide a suitable operating environment of systems

All electronic components which exhibit electrical conductor resistance, generates heat when electricity is passed (Joule - Lenz’s Law). The generated heat is necessary to take into surrounding environment. To reduce the operating temperature of electronic components are used various types of cooling in electronic devices. The released heat is removed from the outside of the device in several ways, either alone or in combination. Intensification of cooling electronic components is in the use of heat transfer through phase changes. From the structural point of view it is important to create a cooling system which would be able to drain the waste heat converter for each mode of operation device. Another important criterion is the reliability of the cooling, and it is appropriate to choose cooling system, which would not contain moving elements. In this article, the issue tackled by the phase change in the heat pipe.

42 ENGINEERING↗

Transition from retrograde to prograde drift instabilities in a magnetron microdischarge

Rotating plasma structures, or “spokes,” in magnetized discharges characterized by perpendicular electric and magnetic fields have been seen in a growing number of studies and are believed to be the result of gradient-driven drift instabilities. Under certain conditions, we have shown the spoke’s rotation to be opposite to the E B direction, i.e., retrograde in its expected direction. Recently, we have linked such counter-intuitive rotation to a local inversion of the electric field. Here, we give further experimental evidence for this inversion and attempt to provide an explanation for a relatively distinct transition seen between retrograde and positive (prograde) drift. In the experiments, a partially magnetized plasma forms inside a magnetron device of mm radius operated with argon. Discharge current–voltage measurements are acquired for a range of argon fill pressure and inter-electrode spacing. We find two branches of operation—a low current branch of negative resistance, coinciding with the retrograde spoke rotation, and a higher current branch of positive resistance, coincident with prograde spoke rotation. We postulate that at low discharge currents, high magnetic field confinement leads to a large density gradient, causing more electron transport to the anode than that demanded by the external circuit. At higher currents, anomalous axial electron transport (across the magnetic field lines) becomes dominant, eliminating the conditions for field inversion. Here, the current thresholds for the field inversion are found to be sensitive to the argon pressure and inter-electrode spacing.

42 ENGINEERING↗

Microscopic model for the ferroelectric field effect in oxide heterostructures

A microscopic model Hamiltonian for the ferroelectric field effect is introduced for the study of oxide heterostructures with ferroelectric components. The long-range Coulomb interaction is incorporated as an electrostatic potential, solved self-consistently together with the charge distribution. A generic double-exchange system is used as the conducting channel, epitaxially attached to the ferroelectric gate. The observed ferroelectric screening effect, namely, the charge accumulation/depletion near the interface, is shown to drive interfacial phase transitions that give rise to robust magnetoelectric responses and bipolar resistive switching, in qualitative agreement with previous density functional theory calculations. The model can be easily adapted to other materials by modifying the Hamiltonian of the conducting channel, and it is useful in simulating ferroelectric field effect devices particularly those involving strongly correlated electronic components where ab initio techniques are difficult to apply.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Review—Practical Challenges Hindering the Development of Solid State Li Ion Batteries

Solid state electrolyte systems boasting Li+ conductivity of >10 mS cm -1 at room temperature have opened the potential for developing a solid state battery with power and energy densities that are competitive with conventional liquid electrolyte systems. The primary focus of this review is twofold. First, differences in Li penetration resistance in solid state systems are discussed, and kinetic limitations of the solid state interface are highlighted. Second, technological challenges associated with processing such systems in relevant form factors are elucidated, and architectures needed for cell level devices in the context of product development are reviewed. Specific research vectors that provide high value to advancing solid state batteries are outlined and discussed.

25 ENERGY STORAGE↗

Research and Development for Novel Thermal Energy Storage Systems (TES) for Concentrating Solar Power (CSP)

The overall objective was to develop innovative heat transfer devices and methodologies for novel thermal energy storage systems for concentrating solar power generation involving phase change materials (PCMs). Specific objectives included embedding thermosyphons and/or heat pipes (TS/HPs) within appropriate phase change materials to significantly reduce thermal resistances within the thermal energy storage system of a large-scale concentrating solar power plant and, in turn, improve performance of the plant. Experimental, system level and detailed comprehensive modeling approaches were taken to investigate the effect of adding TS/HPs on the performance of latent heat thermal energy storage (LHTES) systems.

14 SOLAR ENERGY↗

Biofouling and Corrosion Study for a Novel Linear Guided Wave Energy Converter (Post Access Report)

The overall objective of this project was to examine the reliability and performance of antibiofouling coatings used for a wave energy converter (WEC) developed by E-Wave Technologies. The particular coatings were selected for their low toxicity and potential compatibility with aquaculture. The aim of this work was to 1) test coating solutions to prevent biofouling growth and saltwater corrosion on the static (paddle and attachment frame surface) components of the WEC that are submerged, 2) determine adhesion of the coatings to system components, and 3) assess the ease and effectiveness of biofouling cleaning to insure long term performance of the system. An analysis of commercial coatings was performed using methods to examine the prevention of biofouling and coating adhesion properties on two key materials of the WEC, which were 316L low carbon marine grade stainless steel (SS) and Ultra High Molecular Weight Polyethylene (PE). Three marine antifouling paints were selected based on their unique properties to test how different paint styles perform on different materials. The selected paints were ePaint Ecominder self-polishing paint with Zinc Omadine for slime control, Pettit ECO HRT Copper-Free ablative antifouling with Econea biocide, and Intersleek 1100SR foul release. Pacific Northwest National Laboratory (PNNL) prepared PE and SS substrates coated with the three paints and compared the performance against uncoated substrates when submerged in raw seawater for 3-, 6-, and 9-month (m) time periods. Results in adhesion testing indicated that Pettit and ePaint materials clearly bonded strongly to SS, but did not bond comparably well to PE. It was noted during adhesion testing that the Intersleek surfaces were especially difficult to test as the paint highly resists bonding to the epoxy adhesives used with the adherence testing platform. The wear rate of the coatings was not measured under this study; however, based on adhesion testing, coatings in the sliding regions of the Ewave device are expected to wear rapidly. Sandia National Laboratories (SNL) evaluated the adhesion of three different paints to PE and SS substrates which were exposed to a marine environment for time intervals of 0, 3, 6, and 9 months. From qualitative visual analysis of the 3 in2 coupons when pulled from the tank, the 3 in2 coupons generally only appeared to have biofouling consisting of filamentous algae or diatoms, which all have relatively low mass and can be easily wiped from the surface of coupons. Qualitative visual analysis indicated that ECO HRT and Unpainted were consistently worse than Intersleek and Ecominder at all time points. Results provide insight to aid with down-selection of commercial coatings under static conditions to support reliability of the WEC and potential maintenance schedules. This investigation was conducted using small coupon samples suspended in seawater and the development of testing rigs for dynamic component level testing is needed for future work. In addition, the potential toxicity of these commercial coatings on aquaculture has not been determined by this study. One recommendation is to conduct toxicity investigations at the Environmental Toxicity Laboratory at Oak Ridge National Laboratory.

16 TIDAL AND WAVE POWER↗

Electric current-producing device having sulfone-based electrolyte

Electrolytic solvents and applications of such solvents including electric current-producing devices. For example, a solvent can include a sulfone compound of R1--SO2--R2, with R1 being an alkyl group and R2 a partially oxygenated alkyl group, to exhibit high chemical and thermal stability and high oxidation resistance. For another example, a battery can include, between an anode and a cathode, an electrolyte which includes ionic electrolyte salts and a non-aqueous electrolyte solvent which includes a non-symmetrical, non-cyclic sulfone. The sulfone has a formula of R1--SO2--R2, wherein R1 is a linear or branched alkyl or partially or fully fluorinated linear or branched alkyl group having 1 to 7 carbon atoms, and R2 is a linear or branched or partially or fully fluorinated linear or branched oxygen containing alkyl group having 1 to 7 carbon atoms. The electrolyte can include an electrolyte co-solvent and an electrolyte additive for protective layer formation.

Angell, Charles Austen↗

Current transport and thermoelectric properties of very high power factor Fe{sub 3}O{sub 4}/SiO{sub 2}/p-type Si(001) devices

The current transport and thermoelectric properties of Fe{sub 3}O{sub 4}/SiO{sub 2}/p-type Si(001) heterostructures with Fe{sub 3}O{sub 4} thicknesses of 150, 200, and 350 nm have been investigated between 100 and 300 K. We observe a sharp drop of the in-plane resistivity at 200 K due to the onset of conduction along the Si/SiO{sub 2} interface related to tunneling of electrons from the Fe{sub 3}O{sub 4} into the accumulation layer of holes at the Si/SiO{sub 2} interface, whose existence was confirmed by capacitance-voltage measurements and a two band analysis of the Hall effect. This is accompanied by a large increase of the Seebeck coefficient reaching +1000 μV/K at 300 K that is related to holes in the p-type Si(001) and gives a power factor of 70 mW/K{sup 2}m when the Fe{sub 3}O{sub 4} layer thickness is reduced down to 150 nm. We show that most of the current flows in the Fe{sub 3}O{sub 4} layer at 300 K, while the Fe{sub 3}O{sub 4}/SiO{sub 2}/p-type Si(001) heterostructures behave like tunneling p-n junctions in the transverse direction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Contrast Mechanisms in Secondary Electron e-Beam-Induced Current (SEEBIC) Imaging

Abstract Over the last few years, a new mode for imaging in the scanning transmission electron microscope (STEM) has gained attention as it permits the direct visualization of sample conductivity and electrical connectivity. When the electron beam (e-beam) is focused on the sample in the STEM, secondary electrons (SEs) are generated. If the sample is conductive and electrically connected to an amplifier, the SE current can be measured as a function of the e-beam position. This scenario is similar to the better-known scanning electron microscopy-based technique, electron beam-induced current imaging, except that the signal in the STEM is generated by the emission of SEs, hence the name secondary electron e-beam-induced current (SEEBIC), and in this case, the current flows in the opposite direction. Here, we provide a brief review of recent work in this area, examine the various contrast generation mechanisms associated with SEEBIC, and illustrate its use for the characterization of graphene nanoribbon devices.

47 OTHER INSTRUMENTATION↗

Nanoscale magnetic Josephson junctions and superconductor/ferromagnet proximity effects for low-power spintronics

Competition between superconducting and ferromagnetic ordering at interfaces between ferromagnets (F) and superconductors (S) gives rise to several proximity effects such as odd-triplet superconductivity and spin-polarized supercurrents. A prominent example of an S/F proximity effect is the spin switch effect observed in S/F/N/F superconducting spin valve multilayers, in which the superconducting transition temperature T c is controlled by the angle Φ between the magnetic moments of the F layers separated by a nonmagnetic metallic spacer N. We carried out an experimental study of spin switch effect in Nb/Co/Cu/Co/CoO x nanowires measured as a function of bias current flowing in the plane of the layers. These measurements reveal an unexpected dependence of T c (Φ) on the bias current: T c (Φ) – T c (0) changes sign with increasing current bias. We attribute the origin of this bias dependence of the spin switch effect to a spin Hall current originating in Nb and flowing perpendicular to the plane of the multilayer, which suppresses T c of the multilayer. The bias dependence of spin switch effect can be important for hybrid F/S devices such as cryogenic memory for superconducting computers when device dimensions are scaled down to the nanometer length scale.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Amorphous Metallic NiFeP: A Conductive Bulk Material Achieving High Activity for Oxygen Evolution Reaction in Both Alkaline and Acidic Media

Here, the intrinsic catalytic activity at 10 mA cm –2 for oxygen evolution reaction (OER) is currently working out at overpotentials higher than 320 mV. A highly efficient electrocatalyst should possess both active sites and high conductivity; however, the loading of powder catalysts on electrodes may often suffer from the large resistance between catalysts and current collectors. This work reports a class of bulk amorphous NiFeP materials with metallic bonds from the viewpoint of electrode design. The materials reported here perfectly combine high macroscopic conductivity with surface active sites, and can be directly used as the electrodes with active sites toward high OER activity in both alkaline and acidic electrolytes. Specifically, a low overpotential of 219 mV is achieved at the geometric current density 10 mA cm –2 in an alkaline electrolyte, with the Tafel slope of 32 mV dec –1 and intrinsic overpotential of 280 mV. Meanwhile, an overpotential of 540 mV at 10 mA cm –2 is attained in an acidic electrolyte and stable for over 30 h, which is the best OER performance in both alkaline and acidic media. This work provides a different angle for the design of high–performance OER electrocatalysts and facilitates the device applications of electrocatalysts.

36 MATERIALS SCIENCE↗

NREL's HydroGEN Photoreactor Platform Design and Characterization

This technical report details the design, fabrication, and construction of a flow-through photoreactor developed at The National Renewable Energy Laboratory (NREL). The photoreactor is designed to facilitate indoor or outdoor testing on photoelectrochemical or integrated solar water splitting devices. The photoreactor design described here is based on a previous demonstration. The photoreactor version described herein contains several advanced design features that include: 1) Chassis-chuck two-part design, 2) Separable counter electrode compartments (here, the counter electrodes are anodes), 3) Reduced electrode separation to reduce electrolyte resistance, 4) Improved flow pattern for bubble removal, 5) Mounting for spectroradiometer receptor, 6) Fresnel lens and collimating tube attachments. The photoreactor presented here was designed primarily to accommodate photocathode materials in an illuminated compartment and a dark anode as the oxygen evolution catalyst. The build materials were thus chosen to for acid electrolyte compatibility. Other embodiments could accommodate a photoanode with dark hydrogen evolution catalyst and other build materials for alkaline compatibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure-Driven Liquid Microjunction Surface-Sampling Probe Mass Spectrometry

The rhizosphere is the narrow region of soil surrounding the roots of plants that is influenced by root exudates, root secretions, and associated microbial communities. This region is crucial to plant growth and development and plays a critical role in nutrient uptake, disease resistance, and soil transformation. Understanding the function of exogenous compounds in the rhizosphere starts with determining the spatiotemporal distribution of these molecular components. Using liquid microjunction surface-sampling probe mass spectrometry (LMJ-SSP-MS) and microfluidic devices with attached microporous membranes enables in situ, nondisruptive, and nondestructive spatiotemporal measurement of exogenous compounds from plant roots. However, long imaging times (>2 h) can negatively affect plant heath and limit temporal studies. Here, we present a novel strategy to optimize the number and location of sampling sites on these microporous membrane-covered microfluidic devices. In conclusion, this novel, “structure-driven” sampling workflow takes into consideration the channel structure of the microfluidic device to maximize sampling from the channels and minimize acquisition time (~4× less time in some cases while providing similar chemical image accuracy), thus reducing stress on plants during in situ LMJ-SSP-MS analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication and characterization of extended arrays of Ag{sub 2}S/Ag nanodot resistive switches

Well-ordered Ag{sub 2}S/Ag nanodot arrays with a density of >60 Gbit/in.{sup 2} have been fabricated by sputtering Ag on a silicon substrate using ultrathin porous anodic aluminum oxide membranes as shadow masks, followed by sulfurization treatment at room temperature. The morphology, microstructure, and electrical properties of the as-prepared nanodots were characterized by scanning electron microscopy, x-ray diffractometry, transmission electron microscopy, and conductive atomic force microscopy, respectively. Well-defined resistive switching behavior was observed in these nanodots, and the ON/OFF ratio was found to be higher than 10{sup 2}. The Ag{sub 2}S/Ag nanodot arrays hold substantial promise for use as ultrahigh density nonvolatile memory devices.

36 MATERIALS SCIENCE↗

Fabrication of carbon nanotube nanogap electrodes by helium ion sputtering for molecular contacts

Carbon nanotube nanogaps have been used to contact individual organic molecules. However, the reliable fabrication of a truly nanometer-sized gap remains a challenge. We use helium ion beam lithography to sputter nanogaps of only (2.8 ± 0.6) nm size into single metallic carbon nanotubes embedded in a device geometry. The high reproducibility of the gap size formation provides a reliable nanogap electrode testbed for contacting small organic molecules. To demonstrate the functionality of these nanogap electrodes, we integrate oligo(phenylene ethynylene) molecular rods, and measure resistance before and after gap formation and with and without contacted molecules.

36 MATERIALS SCIENCE↗