Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Structural and Thermal Validations of Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18} Composites Synthesized via Citrate Sol-Gel Spontaneous Combustion Method

The fabrication of single-phase superconductors enabled promising advancements in a wide range of technological applications. Numerous parameters including processing temperature, thermal cycle, chemical composition, doping, and atmosphere will be carefully addressed and optimized. This paper investigates phase stability and compound formation of Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub y} (Y-358) preform powders which were sintered at different temperatures. The precursor powder synthesized via chemical route and employing spontaneous combustion technique, respectively. The presence of Y-358 and YBa{sub 2}Cu{sub 3}O{sub 7-δ} (Y-123) phases in composites sintered at different temperatures with varied phase fractions were further confirmed through Rietveld refinement. The formation of Y-123 phase is dominant in all samples and composite was sintered at 900 °C, which was exhibited higher as compared to Y-358 phase content. The decomposition of different phases present in the composites and reaction temperatures were investigated with simultaneous differential thermal and thermogravimetry analysis.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Critical Current Density and AC Susceptibility of Bi{sub 1.6}Pb{sub 0.4}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} Superconductor with Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} Nanomaterial

The juxtaposition of superconductivity and magnetism is an interesting research topic due to the exclusivity nature of both phenomena. In this paper, we report the effect of nanosized (~ 5 nm) nickel zinc ferrite Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} (NZFO) on Bi{sub 1.6}Pb{sub 0.4}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Bi-2223) superconductor. Bi-2223 powders were prepared using the co-precipitation method. Samples with starting formula Bi{sub 1.6}Pb{sub 0.4}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}(Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4}){sub x} for x = 0 to 0.1 wt% have been prepared. The structure, microstructure, electrical resistance, and AC susceptibility were determined. The transport critical current density, J{sub ct}, was measured using the 1 μV/cm criterion. The non-added sample sintered for 48 h showed the highest zero resistance temperature, T{sub c-zero} (105 K) and J{sub ct} of 1.83 A cm{sup −2} at 40 K. The x = 0.02 wt% sample sintered for 48 h (T{sub c-zero} = 103 K) showed the highest J{sub ct} of 5.30 A cm{sup −2} at 40 K. The peak temperature of the imaginary part of the complex susceptibility, T{sub p}, increased with sintering time and nanoparticle addition, indicating full flux penetration occurred at higher temperatures and improved intergrain coupling. NZFO nanoparticle did not suppress the transition temperature but it improved the transport critical current density by more than five times indicating it enhanced flux pinning and connectivity between grains in the Bi-2223 phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development of thermoelectric fibers for miniature thermoelectric devices

Miniature thermoelectric (TE) devices may be used in a variety of applications such as power sources of small sensors, temperature regulation of precision electronics, etc. Reducing the size of TE elements may also enable design of novel devices with unique form factor and higher device efficiency. Current industrial practice of fabricating TE devices usually involves mechanical removal processes that not only lead to material loss but also limit the geometry of the TE elements. In this project, we explored a powder-processing method for the fabrication of TE fibers with large length-to-area ratio, which could be potentially used for miniature TE devices. Powders were milled from Bi2Te3-based bulk materials and then mixed with a thermoplastic resin dissolved in an organic solvent. Through an extrusion process, flexible, continuous fibers with sub-millimeter diameters were formed. The polymer phase was then removed by sintering. Sintered fibers exhibited similar Seebeck coefficients to the bulk materials. Moreover, their electrical resistivity was much higher, which might be related to the residual porosity and grain boundary contamination. Prototype miniature uni-couples fabricated from these fibers showed a linear I-V behavior and could generate millivolt voltages and output power in the nano-watt range. Further development of these TE fibers requires improvement in their electrical conductivities, which needs a better understanding of the causes that lead to the low conductivity in the sintered fibers.

36 MATERIALS SCIENCE↗

Synthesis and Characterization of Natural Nano-hydroxyapatite Derived from Turkey Femur-Bone Waste

Hydroxyapatite (HAp) is a bioactive and vital material which has found many applications in the biomedical and clinical fields. This bio-ceramic powder can be synthesized via different bio-waste materials. In this study, the production of natural nanohydroxyapatite was produced through calcination of untreated turkey femur-bone waste powder at 850 °C followed by ball milling the powder. The obtained powder was characterized using X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analysis. The morphology, size, and elemental composition of obtained turkey hydroxyapatite (THA) particles were investigated by scanning electron microcopy (SEM), transmission electron microcopy (TEM), and energy dispersive spectroscopy (EDS) analysis, in which the average particle size of ball milled THA was found to be about 85 nm with a Ca/P ratio of 1.63. The powder was then cold pressed and later sintered at 850, 950, 1050, and 1150 °C to evaluate its mechanical properties in terms of compressive strength and hardness. The results revealed that the strength and hardness of the samples increased by increasing the sintering temperature up to 1150 °C. Finally, the maximum values of hardness and compressive strength of the sintered THA were obtained at 1150 °C (37.44 MPa and 3.2 GPa, respectively).

60 APPLIED LIFE SCIENCES↗

Predictive binder jet additive manufacturing enabled by clean burn-off binder design

Binder jet additive manufacturing (BJAM) presents an avenue for advanced manufacturing of various high-value materials due to high deposition rates, scalability, and geometric flexibility. However, conventional organic binders in BJAM introduce residual carbon upon pyrolysis, often leading to imprecise alloy composition in the final sintered part. The undesirable residual carbon from binder burn-off limits the application of BJAM for high-performance alloys due to their high sensitivity to carbon addition. In this study, we have designed poly(vinylpyrrolidone-co-vinyl acetate) (PVP-VAc) as a clean burn-off binder for BJAM, where excess oxygen groups in VAc enable cleaner burn-off and reduce residual carbon retention. Compared to a widely used commercial binder, the optimized PVP-VAc binder reduced residual carbon retention by over 90% in H13 tool steel. The significant reduction in residual carbon enables predictable printing and subsequent sintering of complex H13 tool steel geometries, an alloy known to have substantial challenges around distortion due to the sintering window shifting from carbon addition. The design of a clean burnout binder provides a major path forward for BJAM by enabling new AM designs and applications for composition-sensitive high-performance alloys, such as nickel-based superalloys, titanium alloys, and high alloyed steels.

36 MATERIALS SCIENCE↗

Single-site Pt/La-Al 2 O 3 stabilized by barium as an active and stable catalyst in purifying CO and C 3 H 6 emissions

High-temperature operations present a substantial challenge for developing industrial-capable precious metal catalysts (e.g. Pt/alumina), where the scarce metal atoms easily become wasted as sintered nanoparticles. Using fully dispersed precious metal atoms to deliver the catalysis remains an elusive goal. On a widely used La-stabilized alumina support, we find that the atomically dispersed Pt 1 (II)-O x - species, rather than the much more visible large metal particles, are the actual catalytic sites for the CO and C 3 H 6 oxidation reactions. Unfortunately, the La dopants in alumina support will not hinder the sintering of the active Pt1(II)-Ox- species. As a natural next step, the Ba-Ox- species were introduced to specifically stabilize the single-atom Pt on the La-stabilized alumina support. By implementing this improved formulation, the atomically dispersed Pt on alumina retains the original full dispersion even after 650 °C hydrothermal aging. Intriguingly, with or without the barium additives and/or sintered platinum particles in the catalysts, the intrinsic activity per Pt atom stays intact. Along with other experimental evidence, this leads to the finding that the single-atom Pt is the true catalytic site for the oxidation of CO and C 3 H 6 in the widely-used Pt/La-Al 2 O 3 material system. This work provides a new perspective for efficient precious metal utilization under demanding catalytic conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Potassium loading and thermal aging on K/Pt/Al2O3 high-temperature lean NOx trap catalysts

The effects of K loading and thermal aging on the structural properties and high temperature performance of Pt/K/Al2O3 lean NOx trap (LNT) catalysts were investigated using in situ X-ray diffraction (XRD), temperature-programmed decomposition/desorption of NOx (NOx-TPD), transmission electron microscopy (TEM), NO oxidation and NOx storage tests. In situ XRD results demonstrate that KNO3 becomes extremely mobile on the Al2O3 surface, and experiences complex transformations between orthorhombic and rhombohedral structures, accompanied by sintering, melting and thermal decomposition upon heating. NOx storage results show an optimum K loading around 10% for the best performance at high temperatures. At lower K loadings where the majority of KNO3 stays as a surface layer, the strong interaction between KNO3 and Al2O3 promotes KNO3 decomposition and deteriorates high-temperature performance. At K loadings higher than 10%, the performance drop is not caused by NOx diffusion limitations as for the case of barium-based LNTs, but rather from the blocking of Pt sites by K species, which adversely affects NO oxidation. Thermal aging at 800 ºC severely deactivates the Pt/K/Al2O3 catalysts due to Pt sintering. However, in the presence of potassium, some Pt remains in a dispersed and oxidized form. These Pt species interact strongly with K and, therefore, do not sinter. After a reduction treatment, these Pt species remain finely dispersed, contributing to a partial recovery of NOx storage performance.

Environmental Molecular Sciences Laboratory↗

Zirconium-diboride silicon-carbide composites: A review

Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.

36 MATERIALS SCIENCE↗

Binder jet additive manufacturing method to fabricate near net shape crack-free highly dense Fe-6.5 wt.% Si soft magnets

High silicon (Si) electrical steel has the potential for efficient use in applications such as electrical motors and generators with cost-effective in processing, but it is difficult to manufacture. Increasing the Si content beyond 3 wt.% improves magnetic and electrical properties, with 6.5 wt.% being achievable. The main goal of this research is to design, develop, and implement a scalable additive manufacturing process to fabricate Fe with 6.5 wt.% Si (Fe–6Si) steel with high magnetic permeability, high electrical resistivity, low coercivity, and low residual induction that other methods cannot achieve because of manufacturing limitations. Binder jet additive manufacturing was used to deposit near net shape components that were subsequently sintered via solid-state sintering to achieve near full densification. Here, it is shown that the use of solid-state sintering mitigates cracking since no rapid solidification occurs unlike fusion-based additive technologies. The Fe–6Si samples demonstrated an ultimate tensile strength of 434 MPa, electrical resistivity of 98 μΩ cm, and saturation magnetization of 1.83 T with low coercivity and high permeability. The results strongly supports to replace the only available 0.1 mm thick chemical vapor deposition (CVD) produced Si steel using the cost effective AM method with good mechanical and magnetic properties for motor ap

36 MATERIALS SCIENCE↗

The effect of Ni doping on the mechanical behavior of tungsten

The effect of nickel (Ni) on activated sintering of tungsten has been known and investigated for decades. However, there are few reports on the mechanical properties of tungsten when Ni is added as a low alloying additive with less than 1 wt%. In this work, the mechanical behaviors of tungsten doped with 0.2–1.0 wt% nickel from room temperature up to 400 °C were investigated. The results show that the compression ductility of as-sintered Ni doped tungsten is drastically higher than that of as-sintered pure tungsten at all tested temperatures including room temperature, and the fracture toughness at room temperature is increased by 92%. The results suggest that the ductile-to-brittle transition temperature (DBTT) of tungsten can be reduced substantially by doping with Ni.

36 MATERIALS SCIENCE↗

Additive-free hot-pressed silicon carbide ceramics-A material with exceptional mechanical properties

Densification of silicon carbide without any sintering aids by hot-pressing and rapid hot pressing was investigated. Full density (>99% t.d.) has been reached at 1850 °C, a temperature of at least 150-200 °C lower compared to the up to now known solid state sintered silicon carbide powders. Silicon carbide was freeze granulated and heat treated prior the densification. Furthermore, evolution of microstructure, mechanical properties and creep behavior were evaluated and compared to reference ceramics from as received silicon carbide powder as well as those of commercial one. Novel method results in dense ceramics with Vickers hardness and indentation fracture toughness of 29.0 GPa and 5.25 MPam 1/2 , respectively. Moreover, the creep rate of 3.8 x 10 –9 s –1 at 1450 °C and the load of 100 MPa is comparable to the commercial α-SiC solid state sintered at 2150 °C.

36 MATERIALS SCIENCE↗

Processing of surrogate nuclear fuel pellets for better dimensional control with dry bag isostatic pressing

A study of improved methods of processing fuel pellets was undertaken using ceria and zirconia/yttria/alumina as surrogates. Through proper granulation and vertical vibration (tapping) of the parts bag prior to dry bag isostatic pressing (DBIP), reproducibility of diameter profiles among multiple pellets of ceria was improved by almost an order of magnitude. Reproducibility of sintered pellets was sufficiently good to possibly avoid grinding. Deviation from the mean diameter along the length of multiple pellets, as well as, deviation from roundness, decreased after sintering. This is not generally observed with dry pressed pellets. Thus it is possible to machine to tolerance before sintering if grinding is necessary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrothermal corrosion of silicon carbide joints without radiation

In this paper, hydrothermal corrosion of four types of the silicon carbide (SiC) to SiC plate joints were investigated under pressurized water reactor and boiling water reactor relevant chemical conditions without irradiation. The joints were formed by metal diffusion bonding using molybdenum or titanium interlayer, reaction sintering using Ti—Si—C system, and SiC nanopowder sintering. Most of the joints withstood the corrosion tests for five weeks. The recession of the SiC substrates was limited. Based on the recession of the bonding layers, it was concluded that all the joints except for the molybdenum diffusion bond are promising under the reducing environments without radiation. Finally, the SiC nanopowder sintered joint was the most corrosion tolerant under the oxidizing environment among the four joints.

36 MATERIALS SCIENCE↗

Characterization of high thermal conductivity fuel surrogates before and after ion irradiation

High thermal conductivity nuclear fuels offer important potential advantages over traditional oxide-based fuels such as higher burnup, reduction in fission gas release, and better overall safety of the system. One proposed approach to high thermal conductivity fuels utilizes high thermal conductivity nonfissile additives with UO 2 fuel to lower the fuel operating temperature and thereby take advantage of the highly favorable radiation resistance of UO 2 at lower operating temperatures. However, differential swelling in the matrix and high conductivity additive phases during high dose irradiation could lead to internal cracking and poor performance. In the current study, ceria (CeO 2 ) and zirconia (ZrO 2 ) surrogate matrices were used to model UO2 behavior. Additives of 10 vol. % Al 2 O 3 or SiC in the form of short fibers or platelets were used for the high conductivity second phase. The nuclear fuel surrogates were sintered to achieve densities greater than 93% of the ideal values. Scanning electron microscopy (SEM) imaging and X-ray diffraction confirmed the uniform distribution of the second phase and that no intermetallic second phase was formed during sintering. The thermal conductivity of the sintered samples was measured from 50 °C to 900 °C and confirmed the desirable increase compared to pure CeO 2 /ZrO 2 pellets. Samples were irradiated with 20 MeV Ni 6+ ions at midrange doses ranging from 1 to 15 displacements per atom (dpa) and temperatures from 300 °C to 700 °C. Post irradiation characterization revealed a good stability of the samples at low to medium doses with matrix lattice parameter swelling of < 0.14 % but showed a significant microstructural deterioration and decrease of the mechanical properties at 15 dpa.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Giant dielectric constant response of the composites in ternary system CuO-TiO{sub 2}-CaO

The subsolidus phase relations of the ternary system CuO-TiO{sub 2}-CaO sintered at 950 deg. C in air have been determined by powder X-ray diffraction method. Only one ternary compound CaCu{sub 3}Ti{sub 4}O{sub 12} was found in this system. From room-temperature dielectric property mapping at 10 kHz, a giant dielectric constant (epsilon{sub r}>10{sup 4}) was observed for most of the ceramic composites in the CuO-rich region and in the region along the CaO-CuO binary line. The composites in the CaCu{sub 3}Ti{sub 4}O{sub 12}-rich region were found to give a comparable giant dielectric constant when sintered at 1050 deg. C. The particular microstructure of larger grains with predominant phase surrounded by smaller grains with the secondary phases was found in such composites with a high dielectric constant. The relations between structures and dielectric properties were investigated. An internal barrier layer capacitance effect is the most probable mechanism to explain this particular dielectric behavior. - Graphical Abstract: In the ternary system, CuO-TiO{sub 2}-CaO, a giant dielectric constant (epsilon{sub r}) above 10{sup 4} (red color) was observed in most of the composites sintered at only 950 deg. C in the CuO-rich region. Dashed lines show the phase boundaries.

36 MATERIALS SCIENCE↗

Solar hydrogen production using Ce{sub 1-x}Li{sub x}O{sub 2-{delta}} solid solutions via a thermochemical, two-step water-splitting cycle

The reactivity of Ce{sub 1-x}Li{sub x}O{sub 2-{delta}} (x=0.025, 0.05, 0.075 and 0.1) solid solutions during the redox and two-step water-splitting cycles has been investigated in this work. Thermogravimetric analysis (TGA), X-ray diffraction (XRD) patterns and field-emission scanning electron microscopy (FE-SEM) indicate that there are two reaction mechanisms in the O{sub 2}-releasing step and the shift in the reaction mechanisms occurs in the O{sub 2}-releasing step because of sintering at high temperatures, and a decrease in the concentration of lattice oxygen occurs as the O{sub 2}-releasing step proceeds. The reaction in the O{sub 2}-releasing step follows a second-order mechanism over a temperature range of 1000-1170 Degree-Sign C and a contracting-area model over a temperature range of 1170-1500 Degree-Sign C. According to direct gas mass spectroscopy (DGMS), ceria doped at 5 mol% Li exhibits the highest reactivity in the O{sub 2}-releasing step during both redox cycles in air and two-step water-splitting cycles, whereas ceria doped at 2.5 mol% Li yields the highest amount of hydrogen (4.79 ml/g) in the H{sub 2}-generation step during the two-step water-splitting cycles, which is higher than ceria doped with other metals. DGMS and electrochemical impedance spectroscopy (EIS) suggest that the average reaction rate in the H{sub 2}-generation step is influenced by the concentration of extrinsic oxygen vacancies, and thus, the reactivity in the H{sub 2}-generation step, to some degree, could be tuned by varying the concentration of extrinsic oxygen vacancies (Li content). - Graphical abstract: Average reduction fraction of Ce{sub 1-x}Li{sub x}O{sub 2-{delta}} (x=0.025, 0.05, 0.075 and 0.10) solid solutions versus Li content in the O{sub 2}-releasing step during the redox cycles in air and the two-step water-splitting cycles. Highlights: Black-Right-Pointing-Pointer We have investigated Li-doped ceria for hydrogen production using two-step water-splitting cycles. Black-Right-Pointing-Pointer The sintering effect on the reaction mechanisms was first clarified. Black-Right-Pointing-Pointer The shift of reaction mechanisms occurs during the O{sub 2}-releasing step. Black-Right-Pointing-Pointer The reaction-mechanism shift occurs because of sintering at high temperatures. Black-Right-Pointing-Pointer Doping at 2.5 mol% Li results in the highest H{sub 2} yield and cyclability for hydrogen production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High temperature behavior of zirconium germanates

The high temperature behavior of zirconium germanates ZrGeO₄ and Zr₃GeO₈ up to 2300 °C has been studied using the original photoemission thermal analysis technique with the comprehensive physicochemical study of solid and gaseous intermediate and final products. The two-stage process of incongruent sublimation of GeO₂ was established and the phase boundary of the homogeneity range for ZrGeO₄ and Zr₃GeO₈ were deduced from the thermal analysis, X-ray diffraction and Raman spectroscopy studies. A high tendency to sintering of the final ZrO₂ product is discussed. - Graphical abstract: The decomposition of zirconium germanates leads to the formation of gaseous GeO₂ and solid sintered ZrO₂ and occurs via two stages with the formation of intermediate ZrO₂-rich solid solution. Highlights: •Thermal behavior of ZrGeO₄ and Zr₃GeO₈ was studied using the original thermal analysis technique in wide temperature range. •The decomposition occurs via two stages with the formation of intermediate ZrO₂-rich solid solution. •The decomposition of zirconium germanates leads to the formation of gaseous GeO₂ and solid sintered ZrO₂. •The temperature of decomposition is strongly depended on the total gas pressure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗