Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simulation Use Case”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Simulating nonlinear cosmological structure formation with massive neutrinos

We present a new method for simulating cosmologies that contain massive particles with thermal free streaming motion, such as massive neutrinos or warm/hot dark matter. This method combines particle and fluid descriptions of the thermal species to eliminate the shot noise known to plague conventional N-body simulations. We describe this method in detail, along with results for a number of test cases to validate our method, and check its range of applicability. Using this method, we demonstrate that massive neutrinos can produce a significant scale-dependence in the large-scale biasing of deep voids in the matter field. We show that this scale-dependence may be quantitatively understood using an extremely simple spherical expansion model which reproduces the behavior of the void bias for different neutrino parameters.

79 ASTRONOMY AND ASTROPHYSICS↗

Plasmon-enhanced phonon and ionized impurity scattering in doped silicon

Historically, two microscopic electron scattering calculation methods have been used to fit macroscopic electron mobility data in n-type silicon. The first method was performed using a static system that included long-range electron-plasmon scattering; however, the well-known Born approximation fails in this case when dealing with electron-impurity scattering. In the second method, sophisticated numerical simulations were developed around plasmon-excited potential fluctuations and successfully reproduced the mobility data at room temperature. In this paper, we propose a third method as an alternative to the first method. First, using a fluctuating system, which was characterized on the basis of our recently experimentally extracted plasmon-excited potential fluctuations, the microscopic calculations reveal enhanced short-range scattering of electrons by phonons and ionized impurities due to increased electron temperature and increased screening length, respectively. The increased hot electron population makes the Born approximation hold, which eases the overall calculation task substantially. Then, we return to the static system while incorporating plasmon-enhanced impurity scattering. The resulting macroscopic electron mobility shows fairly good agreement with data over wide ranges of temperatures (200–400 K) and doping concentrations (10{sup 15}–10{sup 20 }cm{sup −3}). Application of the proposed method to strained silicon is also demonstrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Heat‐Generating Nuclear Waste in Salt: Field Testing and Simulation

Core Ideas A field‐scale experiment and numerical simulations confirm salt backfill behavior. Simulations closely match temperature around and under the piled salt backfill. Results indicate limited dissolution–precipitation reactions around the heat source. Alteration of backfill is unlikely if the drift is allowed to dry before emplacement. Investigations relating to in‐drift disposal of heat‐generating nuclear waste in salt have raised questions about heat–brine interactions in the unsaturated run‐of‐mine (RoM) salt pile used as backfill. These interactions have the potential to change the structure of the RoM salt surrounding the canister, possibly altering long‐term containment of the source. An experiment is in progress at the Waste Isolation Pilot Plant (WIPP), New Mexico, in which a heated canister was placed on the floor of an open drift, covered in a pile of RoM salt, and energized with 1000 W. Temperature in the RoM salt pile had stabilized after about 15 d, allowing evaluation of the heat‐up period of the ongoing experiment. Using a multiphase porous flow simulator that has been modified to handle salt‐specific coupled processes, we examined coupled thermal–hydrological–chemical behavior in the RoM salt pile. Our simulations suggest that for the relatively dry cases examined, porosity changes within RoM salt in a generic salt repository are likely to be minor in the period between waste emplacement and plastic closure of the drift. The primary sensitivity for porosity change is to the early moisture content of the RoM salt used to cover the canister. Secondary influences include moisture availability from the disturbed rock zone (DRZ) surrounding the drift and the capillary pressure ratio between the DRZ and the RoM salt. Early changes in porosity and permeability may be affected by moisture content, but this was not observed in the test. Such changes would be most likely to occur when using damp RoM salt or if waste is emplaced in a drift immediately following opening of the drift before evaporative dewatering of the drift walls occurs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An improved fitting formula for the dark matter bispectrum

In this paper we present an improved fitting formula for the dark matter bispectrum motivated by the previous phenomenological approach of ref. [1]. We use a set of LCDM simulations to calibrate the fitting parameters in the k-range of 0.03 h/Mpc ≤ k ≤ 0.4 h/Mpc and in the redshift range of 0 ≤ z ≤ 1.5. This new proposed fit describes well the BAO-features although it was not designed to. The deviation between the simulations output and our analytic prediction is typically less than 5% and in the worst case is never above 10%. We envision that this new analytic fitting formula will be very useful in providing reliable predictions for the non-linear dark matter bispectrum for LCDM models.

79 ASTRONOMY AND ASTROPHYSICS↗

Integrated Heat Exchanger-Phase Change Material Thermal Energy Storage System

The purpose of this study is to experimentally investigate the thermal performance of an innovative thermal energy storage (TES) system that combines the advantages of the phase-change material (PCM)/graphite foam latent heat TES medium developed at Argonne National Laboratory (Argonne) and the internally supported plate-fin (ISPE) cell architecture heat transfer fluid (HTF) flow channels developed at Brayton Energy (Brayton). Several essential tasks were accomplished: (1) Thermal property characterization. Thermal properties of the graphite foam were characterized, providing necessary data for experimental result analysis and numerical simulation. (2) Design and optimization of lab-scale test module. Based on Brayton’s full-scale heat exchanger (HX)-TES system, the experimental test module was designed, optimized, and fabricated. (3) Thermal performance testing and data analysis. Five cycle tests were successfully conducted—including one with approximately 3.5 psig of pressure applied to the diaphragms—to investigate the thermal performance of the experimental test module for charging and discharging. Temperature profiles were generated for each charging test and discharging test as a function of time. The temperature profiles clearly show three TES stages: sensible heat (temperature increase), latent heat (melting), and sensible heat (temperature increase) for the charging process. Similarly, the temperature profiles clearly show three thermal energy release stages: sensible heat (temperature decrease), latent heat (solidification), and sensible heat (temperature decrease). Melting and solidification of the PCM generally occurred in relatively narrow temperature ranges, indicated by the flattened temperature regions in the temperature profiles. These phase changes ranged approximately 3°C for melting and 3.5°C for solidification. The charging and discharging temperature profiles were similar for similar experimental parameter tests whether or not pressure was applied to the diaphragm to eliminate the gap between the HX surface and the TES subsystem. This indicates that the effect of a small gap between the HX surface and the TES subsystem is insignificant for charging and discharging. (4) Comparison of experimental data and simulation results. We compared the experimental data to the numerical simulation results. Numerical simulations were conducted by using the ANSYS FLUENT 2019 R3 commercial computational fluid dynamics software. The predicted phase-change times agreed reasonably well with those from the experimental data. In most cases, the estimated time differences between the relative phase changes were within 16%. The predicted start and end times for the charging process agreed well with those from the experimental data. However, the simulation results showed earlier start and end times than the experimental data for the discharging process. Overall, the experimental data and its comparison with the simulation predictions verified the technical viability of the integrated ISPF HX-PCM/graphite foam latent-heat TES system.

25 ENERGY STORAGE↗

Verification and Validation of COMSOL for Heat Transfer in Thin Rectangular Channels Using NACA Test Results

Currently efforts are underway at Oak Ridge National Lab (ORNL) to convert the High Flux Isotope Reactor (HFIR) from high enriched uranium to low enriched uranium fuel. In order to provide confidence to the thermal hydraulics calculations, computational fluid dynamics (CFD) simulations – simulated using COMOSOL – have been employed to calculate the pressure drop and heat transfer in the coolant. While CFD simulations provide well resolved results, turbulence models include a large amount of assumptions and must be validated for use in any safety-based analysis. In HFIR, long thin involute fuel plates are separated by coolant channels of equal size. The coolant channels are best described as thin rectangular channels. Unfortunately, there are few studies verifying and validating CFD for use in thin rectangular channels. This study seeks to bridge that gap by verifying, validating, and comparing various CFD models used in thin channels. To verify and validate CFD for use in thin channels, a series of simple analytic test cases are employed, and MMS is used to further verify the COMSOL tool and mesh geometry. For the validation, a series of tests conducted at NASA were simulated in COMSOL. The results of this study are three-fold. First, it verifies the ability of COMSOL to model heat transfer in thin channels. Second, it addresses the various aspects of CFD modeling that are of greatest concern for heat transfer simulations in the geometry. Third, and finally, it discusses the ability of various CFD models used in COMSOL to accurately predict heat transfer in narrow rectangular channels.

Howard, Trevor↗

Plant model of KIPT neutron source facility simulator

Argonne National Laboratory (ANL) of the United States and Kharkov Institute of Physics and Technology (KIPT) of Ukraine are collaborating on constructing a neutron source facility at KIPT, Kharkov, Ukraine. The facility has 100-kW electron beam driving a subcritical assembly (SCA). The electron beam interacts with a natural uranium target or a tungsten target to generate neutrons, and deposits its power in the target zone. The total fission power generated in SCA is about 300 kW. Two primary cooling loops are designed to remove 100-kW and 300-kW from the target zone and the SCA, respectively. A secondary cooling system is coupled with the primary cooling system to dispose of the generated heat outside the facility buildings to the atmosphere. In addition, the electron accelerator has a low efficiency for generating the electron beam, which uses another secondary cooling loop to remove the generated heat from the accelerator primary cooling loop. One of the main functions the KIPT neutron source facility is to train young nuclear specialists; therefore, ANL has developed the KIPT Neutron Source Facility Simulator for this function. In this simulator, a Plant Control System and a Plant Protection System were developed to perform proper control and to provide automatic protection against unsafe and improper operation of the facility during the steady-state and the transient states using a facility plant model. This report focuses on describing the physics of the plant model and provides several test cases to demonstrate its capabilities. The plant facility model uses the PYTHON script language. It is consistent with the computer language of the plant control system. It is easy to integrate with the simulator without an additional interface, and it is able to simulate the transients of the cooling systems with system control variables changing on real-time.

43 PARTICLE ACCELERATORS↗

Design of Zone-Based Hierarchical Protection System for 100% Renewable Microgrids

Design of a reliable and secure protection system for a 100% renewable microgrid with only inverter-based resources (IBRs), is quite challenging. Most of the existing protection schemes in the state-of-the-art are suitable for microgrids with mixed-type of distributed energy resources (DERs) that covers both rotating machine-based DERs as well as IBR-based DERs, where the fault current level is moderately high. Due to drastic reduction in fault current level based on mode of operation and the variation of the low fault current level based on the operating level of the IBRs, the existing protection schemes face critical challenges, in case of a 100% renewable microgrid. This article proposes a zone-based hierarchical protection scheme that partitions a microgrid into various zones-of-protection and assigns speed-based hierarchical protection schemes in order to address the fundamental challenges of such microgrids. The performance of the proposed scheme is evaluated using time-domain simulation study on a microgrid test system. The results corroborates that the proposed hierarchical zone-based protection scheme exhibits enhanced reliability, security and dependability while tested with various fault cases (fault types, locations, and impedances), and non-fault cases during both grid-tied and islanded mode.

grid-forming inverter↗

TIME DEPENDENT NONEQUILIBRIUM IONIZATION OF TRANSITION REGION LINES OBSERVED WITH IRIS

The properties of nonstatistical equilibrium ionization of silicon and oxygen ions are analyzed in this work. We focus on five solar targets (quiet Sun; coronal hole; plage; quiescent active region, AR; and flaring AR) as observed with the Interface Region Imaging Spectrograph (IRIS). IRIS is best suited for this work owing to the high cadence (up to 0.5 s), high spatial resolution (up to 0.″32), and high signal-to-noise ratios for O iv λ1401 and Si iv λ1402. We find that the observed intensity ratio between lines of three times ionized silicon and oxygen ions depends on their total intensity and that this correlation varies depending on the region observed (quiet Sun, coronal holes, plage, or active regions) and on the specific observational objects present (spicules, dynamic loops, jets, microflares, or umbra). In order to interpret the observations, we compare them with synthetic profiles taken from 2D self-consistent radiative MHD simulations of the solar atmosphere, where the statistical equilibrium or nonequilibrium treatment of silicon and oxygen is applied. These synthetic observations show vaguely similar correlations to those in the observations, i.e., between the intensity ratios and their intensities, but only in the nonequilibrium case do we find that (some of) the observations can be reproduced. We conclude that these lines are formed out of statistical equilibrium. We use our time-dependent nonequilibrium ionization simulations to describe the physical mechanisms behind these observed properties.

79 ASTRONOMY AND ASTROPHYSICS↗

Design of Zone-Based Hierarchical Protection System for 100% Renewable Microgrids: Preprint

Design of a reliable and secure protection system for a 100% renewable microgrid with only inverter-based resources (IBRs), is quite challenging. Most of the existing protection schemes in the state-of-the-art are suitable for microgrids with mixed-type of distributed energy resources (DERs) that covers both rotating machine-based DERs as well as IBR-based DERs, where the fault current level is moderately high. Due to drastic reduction in fault current level based on mode of operation and the variation of the low fault current level based on the operating level of the IBRs, the existing protection schemes face critical challenges, in case of a 100% renewable microgrid. This article proposes a zone-based hierarchical protection scheme that partitions a microgrid into various zones-of-protection and assigns speed-based hierarchical protection schemes in order to address the fundamental challenges of such microgrids. The performance of the proposed scheme is evaluated using time-domain simulation study on a microgrid test system. The results corroborates that the proposed hierarchical zone-based protection scheme exhibits enhanced reliability, security and dependability while tested with various fault cases (fault types, locations, and impedances), and non-fault cases during both grid-tied and islanded mode.

grid-forming inverter↗

Characteristics and estimates of double parton scattering at the Large Hadron Collider.

We evaluate the kinematic distributions in phase space of 4-parton final-state subprocesses produced by double parton scattering, and we contrast these with the final-state distributions that originate from conventional single parton scattering. Our goal is to establish the distinct topologies of events that arise from these two sources and to provide a methodology for experimental determination of the relative magnitude of the double parton and single parton contributions at Large Hadron Collider energies. We examine two cases in detail, the bb{sup -} jet-jet and the 4 jet final states. After full parton-level simulations, we identify a few variables that separate the two contributions remarkably well, and we suggest their use experimentally for an empirical measurement of the relative cross section. We show that the double parton contribution falls off significantly more rapidly with the transverse momentum p{sub T}{sup j1} of the leading jet, but, up to issues of the relative normalization, may be dominant at modest values of p{sub T}{sup j1}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Stochastic Optimal Scheduling of Residential Appliances with Renewable Energy Sources

This paper proposes a stochastic, multi-objective optimization model within a Model Predictive Control (MPC) framework, to determine the optimal operational schedules of residential appliances operating in the presence of renewable energy source (RES). The objective function minimizes the weighted sum of discomfort, energy cost, total and peak electricity consumption, and carbon footprint. A heuristic method is developed for combining different objective components. The proposed stochastic model utilizes Monte Carlo simulation (MCS) for representing uncertainties in electricity price, outdoor temperature, RES generation, water usage, and non-controllable loads. The proposed model is solved using a mixed integer linear programming (MILP) solver and numerical results show the validity of the model. Case studies show the benefit of using the proposed optimization model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Comparison between numerical-relativity and post-Newtonian waveforms from spinning binaries: The orbital hang-up case

We compare results from numerical simulations of spinning binaries in the 'orbital hang-up' case, where the binary completes at least nine orbits before merger, with post-Newtonian results using the approximants Taylor T1, T4, and Et. We find that, over the ten cycles before the gravitational-wave frequency reaches M{omega}=0.1, the accumulated phase disagreement between numerical relativity (NR) and 2.5 post-Newtonian (PN) results is less than three radians, and is less than 2.5 radians when using 3.5PN results. The amplitude disagreement between NR and restricted PN results increases with the black holes' spin, from about 6% in the equal-mass case to 12% when the black holes' spins are S{sub i}/M{sub i}{sup 2}=0.85. Finally, our results suggest that the merger waveform will play an important role in estimating the spin from such inspiral waveforms.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Integrated modeling framework (FVCOM-ICM/Toxi) to simulate the fate and transport of polychlorinated biphenyls in urban estuaries–Case study for Puget Sound, WA

Puget Sound is an urban estuary that exhibits persistent polychlorinated biphenyls (PCBs) contamination despite years of remediation efforts. For robust management actions, determining the timing, location, and magnitude of PCB loading sources and transport pathways using field data alone is challenging due to complex water circulation and biogeochemical processes. Here, this study aims to develop an integrated modeling framework that couples complex estuarian circulation with biogeochemical processes and associated interactions with PCB kinetics. The model simulates PCB accumulation in the lower tropic food web, demonstrating PCB intrusion into primary producers and its biomagnification in pelagic consumers. The PCB data from a new field survey was used to calibrate/validate the new PCB modeling framework for Puget Sound. The software program of the modeling framework is available to the user community for the applications of toxic contaminants transport in marine waters.

54 ENVIRONMENTAL SCIENCES↗

Enhanced focus steering abilities of multi-element therapeutic arrays operating in nonlinear regimes

Steering abilities of a typical HIFU therapeutic array operated in linear and nonlinear regimes were compared using numerical simulation with the 3D Westervelt equation. The array included 256 elements of 1.2 MHz frequency and 6.6 mm diameter distributed in a quasi-random pattern over a spherical shell with a 130 mm aperture and a focal length of 120 mm. In the case of linear focusing, thermal effects are proportional to the intensity level and the criterion for safe array operation is that the intensity in the grating lobes should be less than 10% of the intensity in the main focus. In the case of nonlinear focusing, the heating effect is no longer proportional to intensity; therefore the heat deposition rate was chosen as the relevant metric, using the same 10% threshold for the secondary lobe in comparison with the focal maximum. When steering the focus, the same linearly predicted intensity level at the main focus was maintained by increasing the array power. Numerical simulations of the acoustic field were performed for nonlinear propagation both in water and in tissue. It was shown that for shock-forming conditions in the main focus, the steering range of safe electronic focusing is larger than that for linear propagation conditions. Nonlinear sonication regimes therefore can be used to enlarge tissue volumes that can be sonicated using electronic steering of the focus of HIFU arrays.

42 ENGINEERING↗

Sensor Placement Optimization Study for the Built Environment: Operational Use Cases

Systems of fixed-position radiation sensors can provide information that assists emergency responders following nuclear and radiological incidents. State, local, tribal, and territorial (SLTT) government agencies that implement systems of fixed-position sensors are faced with numerous decisions regarding sensor selection, quantity, and placement. To develop guidance on implementation of radiation detection systems, we simulated the release of radioactive material in an urban environment using a combination of three models: the Weather Research Forecasting (WRF), Quick Urban and Industrial Complex (QUIC), and Monte Carlo N-Particle (MCNP) models. We then evaluated the performance of several hypothetical sensor systems. The small number of simulations we conducted are not sufficient to generate definitive design guidance for radiation sensor systems, but we did identify trends that would be of interest to emergency planners. For a scenario that releases 1000 curies of Cs-137, radiation detectors were needed at 500-meter intervals to have a high likelihood of event detection and to estimate source location and plume detection. We also noted that optimal detector altitude varied with distance to the source. We recommend additional research in this area be conducted to support developing sensor placement guidelines that expand on a range of locations, isotopes, activity levels, and different weather conditions. Original simulation strategies included a range of environments, additional radioisotopes (Am241 and AmBe), and a larger selection of sensor types. These types of expansions would support SLTT guidance on sensor system recommendations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling and simulation performance of sucker rod beam pump

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗