Search NASA⌕ Search

SEARCH · Search NASA

Results for “Small reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Dissolution Behavior of Plutonium Containing Zirconia-Magnesia Ceramics

This study explores the dissolution properties of zirconia-magnesia ceramics containing plutonium as the basis of an inert atrix nuclear fuel. The magnesium oxide phase remains pure MgO, while the zirconia incorporates a small amount of magnesium oxide along with all of the plutonium oxide and erbium oxide. The performance of the material under reactor and repository environments was examined. Reactor conditions are examined using a pressure vessel to expose the material to 300 degrees C water. To assess the performance of the material as a waste form it was submerged in 90 degrees C water for 1000 h. In both aqueous dissolution studies there was minimal release of less than 0.8 wt.% of plutonium from the material. To examine the potential for recycling, the dissolution behavior of the fuel matrix was examined in acidic solutions: pure nitric acid and a nitric acid-hydrofluoric acid-peroxide solution. Both acidic media exhibit potential for dissolving plutonium from the zirconia matrix. The experiments performed in this study are meant to lay a foundation for the chemical performance of zirconia-magnesia inert matrix fuel containing fissile material and burnable poison.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Atmospheric-pressure guided streamers for liposomal membrane disruption

The potential to use liposomes (LIPs) as a cellular model in order to study interactions of cold atmospheric-pressure plasma with cells is herein investigated. Cold atmospheric-pressure plasma is formed by a dielectric-barrier discharge reactor. Large multilamellar vesicle liposomes, consisted of phosphatidylcholine and cholesterol, are prepared by the thin film hydration technique, to encapsulate a small hydrophilic dye, i.e., calcein. The plasma-induced release of calcein from liposomes is then used as a measure of liposome membrane integrity and, consequently, interaction between the cold atmospheric plasma and lipid bilayers. Physical mechanisms leading to membrane disruption are suggested, based on the plasma characterization including gas temperature calculation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Data-Driven Model Predictive Control for Temperature Management of Heat Pipe Microreactor

A data-driven model predictive control (MPC) was developed to enable the self-regulating capability of heat pipe (HP) nuclear microreactors. The MPC can proactively respond to potential disturbances of HP microreactors using three approaches for system identifications: linear state-space model, feedforward neural network, and recurrent neural networks with long short-term memory units. We present numerical results of data-driven MPCs to control the temperatures of selected HPs in a 37-HP test article. Our results show qualitatively that all data-driven MPCs produced similar control actions, while quantitatively, with artificial neural nets (especially feedforward neural nets), MPC can better follow drastic changes in setpoints with small errors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Developing Ultra-small Scale Mechanical Testing Methods and Microstructural Investigation Procedures for Irradiated Materials

Nuclear materials are an essential aspect of nuclear engineering. While great effort is spent on designing more advanced reactors or enhancing a reactor’s safety, materials have been the bottleneck of most new developments. The designs of new reactor concepts are driven by neutronic and thermodynamic aspects, leading to unusual coolants (liquid metal, liquid salt, gases), higher temperatures, and higher radiation doses than conventional light water reactors have. However, any (nuclear) engineering design must consider the materials used in the anticipated application in order to ever be realized. Designs which may look easy, simple and efficient considering thermodynamics or neutronic aspects can show their true difficulty in the materials area, which then prevents them from being deployed. In turn, the materials available are influencing the neutronic and thermodynamic designs and therefore must be considered from the beginning, requiring close collaborations between different aspects of nuclear engineering. If a particular design requires new materials, the licensing of the reactor must be considered, but licensing can be a costly and time consuming process that results in long lead times to realize true materials innovation.

36 MATERIALS SCIENCE↗

Updates and Verifications of the PROTEUS Suite in FY19

In FY19 efforts were made on updating and verifying the PROTEUS suite in terms of depletion and fuel cycle capabilities, updated MSR capabilities, improving code usability, and supporting simulation of micro reactors. The fuel reloading and shuffling schemes as well as the built-in depletion solver were implemented to add the fuel cycle capability to PROTEUS-NODAL. PERSENT can run with PROTEUS-NODAL which now produce the CCCC interface files. The MSR simulation capability was further updated by making PROTEUS-NODAL coupled with SAM via the MOOSE wrapper. The high fidelity solvers of PROTEUS were updated to support the multiphysics simulation of SFRs and micro reactors. The coupled system of PROTEUS / FLUENT / ANLHTP was developed using Python-based external drivers, demonstrating the coupled simulation for small 3D test problems with heat pipe failure transients. In addition, the gamma transport capability was implemented to compute the detailed gamma distributions that determines the primary heat sources for the fuel assembly structure and non-fueled assemblies. Verification tests using fuel assembly and 2D core problems indicated very good agreement in heating distributions between PROTEUS and VARIANT / GAMSOR solutions. For user support, the NEAMS Workbench was updated to include PROTEUS-NODAL and further extended to handle PROTEUS-MOC for which the support of Workbench is limited, instead requiring the off-line generation of mesh files and corresponding cross section sets. The utility tools of PROTEUS were also updated to support users to model and simulate complicated and non-conventional geometry cores.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ECAR-6585 MARVEL Core Support Structure Analysis: Project #33526

Idaho National Laboratory (INL) is developing a small microreactor to produce electrical power utilizing a small nuclear core and stirling engines for power output under the Microreactor Application Research Validation and Evaluation (MARVEL) program. The MARVEL Reactor (Figure 1) will be installed in the Transient Reactor Test (TREAT) Facility. Walsh Engineering Services, PC (WES) has contracted with the INL to detail the final design. There are six main systems in the MARVEL, one of which is the Fuel and Core System (FCS). The FCS contains a subsystem–the Core Support Structures Subsystem (CSS)–that supports and orients each of the 36 nuclear fuel pins in the MARVEL Reactor System. The FCS (apart from the fixed Beryllium Oxide radial reflectors) is shown in light green and is depicted in more detail in Figure 1 and Figure 2. The main subject of this analysis is the lower grid plate, which is the principal item in the CSS which supports the fuel, see Figure 3. Additionally, the upper grid plate thermal expansion of the upper grid plate is presented in Appendix A.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Catalytic ignition model in monolithic reactor with in-depth reaction

A transient model has been developed to study ignition in a monolithic catalytic reactor. Special features are the inclusion of thermal and species structures in the porous catalytic layer and the resolution of small-time-scale events. Catalyst loading is used as a parameter to study these structure variations before and after ignition. Regions where the catalytic reaction is kinetically controlled and regions where the reaction is diffusionally controlled are identified in both steady and transient states.

Tien, Ta-Ching↗

Preparation of liquid fuel test rig in Halden HBWR

Introduction of liquid nuclear fuel may open a way to develop new ideas for fuel engineers. The first action is a small step to develop bottle-shaped devices which encapsulate liquid fuels and enable safe irradiation in Halden Heavy Water Boiling Reactor (HBWR). Thermo-hydrodynamics 3D code calculations were made to evaluate heat removal performance of the device by natural convection. Preparation of mock-up testing and consideration of safety issues to use liquid fuel in water reactor are presented. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Depletion Analysis of Additively Manufactured Control Elements in HFIR

The High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory is a flux-trap type research reactor which provides one of the highest steady-state neutron sources in the world. HFIR neutrons are used for a range of research applications, including scattering experiments, materials irradiation, and isotope production. The HFIR core operates at 85 MW and is light water cooled and moderated. The core consists of several concentric cylindrical regions, as depicted in Fig. 1. At the center of the core is the flux trap, where the thermal flux reaches a maximum on the order of 10{sup 15} neutrons/cm{sup 2}-s. Immediately surrounding the flux trap are two annular fuel elements, an inner fuel element and an outer fuel element, each loaded with hundreds of thin fuel plates curved into an involute shape. Surrounding the outer fuel element are two thin control elements (CEs), an inner CE (ICE) and an outer CE (OCE). The CEs are axially zoned into three regions according to absorption strength: the white regions contain only structural aluminum and do not significantly contribute to absorption; the gray regions contain tantalum (Ta) as the primary absorber with a concentration of 30% by volume; and the black regions contain europium in the form of Eu{sub 2}O{sub 3} with a concentration of 33% by volume. A thick beryllium reflector is the final core component surrounding the CEs. A particular challenge to efficient maintenance and continued operation of HFIR is fabrication of the CEs, the current methods for which are tedious, outdated, and expensive. In an effort to improve the operational economics of HFIR and to demonstrate the application of advanced manufacturing techniques to the production of nuclear reactor components, the ultrasonic additive manufacturing (UAM) process is being investigated for fabrication of the HFIR CEs. This application of UAM involves directly embedding small cylindrical compacts (∼5.6 mm diameter, ∼1.7 mm thick) containing 60% neutron poison by volume into an aluminum matrix, using energy from ultrasonic vibrations to bond the compacts to the aluminum. The CEs contain discrete regions of absorbing material, in contrast to the standard design with homogeneously distributed absorbers. This novel design necessitates an investigation into how the HFIR core neutronic behavior differs from the case with homogeneous CEs so as to ascertain the feasibility of using additively manufactured CEs in HFIR. From an operations perspective, it is desirable for the discrete CEs to match the performance of the homogeneous CEs as closely as possible so as to avoid reconsideration of established safety margins. Earlier analyses of HFIR under beginning of cycle (BOC) conditions have indicated that although absorption properties on a local scale differ significantly between CE designs, the macroscopic behavior (neutron multiplication and flux and power distributions) of the HFIR core is not significantly altered. This study now addresses CE performance throughout depletion of the HFIR core during a reactor cycle. These analyses help to construct a more complete picture of the feasibility of employing additively manufactured CEs in HFIR and will reveal any adjustments which must be made to the design in order to maintain acceptable performance. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Fidelity CFD Simulation of Mixed Convection and Forced Convection in a Pebble Bed Test Reactor Core

The Hermes low-power [35-MW(thermal)] reactor will be built and operated by Kairos Power LLC (KP) to demonstrate its fluoride salt-cooled high-temperature reactor (FHR) technology. In the KP FHR, the reactor core is composed of randomly packed pebbles with TRISO fuel particles inside with FLiBe flow upward through the core acting as a coolant. Previous numerical and experimental studies have been limited to either a small-size bed or to a lack of detailed measurements for heat transfer. Here, to address the lack of high-fidelity heat transfer data in a real-size FHR core, in this study, we simulated a pebble bed core with 34 374 pebbles randomly packed, similar to the Hermes reactor's size. The core radius was 14 times that of the pebble diameter, while the core height was 45 times. In this work, we were particularly interested in a mixed convection regime, where buoyancy is important. Therefore, we performed several large-eddy simulations at different Reynolds numbers (160 to 1000) with gravitational force included. The spectral element computational fluid dynamics code NekRS with graphics processing unit acceleration was used for this study. The low-Mach number approximation was applied to address property changes in the FLiBe and to account for buoyancy. A pure hexahedral mesh with 60 million elements was generated by the Voronoi cell method. At the polynomial order of 5, the total degrees of freedom was 7.5 billion. The developed case in this work is the first of its kind in terms of size and complexity. The local numerical data across the domain were obtained and compared with empirical correlations. After examining the data, we found the following conclusions. For pressure drop, the Reger correlation predicted less than a 5% error. On the other hand, for heat transfer, the Wakao correlation outperformed the others. Based on our findings, we recommend the use of the Wakao correlation for the Nusselt number calculation, and for pressure drop, the KTA (Kerntechnischer Ausschuss) correclation, among the available experimental correlations. In conclusion, the Reger direct numerical simulation-driven correlation for pressure drops should also be considered, given its best agreement with our calculations.

Mixed Convection↗

Assessment of the High Flux Isotope Reactor Cybersecurity Initiative

Recent cyber-attacks on industrial control systems, and inadvertent exposure of nuclear plant systems to cyber-exploits underscore the need for plant operators to adopt and deploy cyber-security defense solutions made for industrial control systems. Of increasing concern is the fact that international cyber hackers are beginning to target critical infrastructure, and because these more modern controls systems depend on advanced use of digital systems, they are more vulnerable than ever before to cyber-attacks. Traditional cyber defense strategies and products that have been available for decades are tailored for use on IT or corporate networks but can cause interruptions and catastrophic damage when deployed on industrial control system networks. The Department of Energy (DOE) Office of Nuclear Energy established the Gateway for Accelerated Innovation in Nuclear (GAIN) program to provide private companies pursuing innovative nuclear energy technologies with access to the technical support necessary to move toward commercialization. One of these GAIN small business vouchers was awarded to Dragos, Inc. to enable collaboration with Oak Ridge National Laboratory (ORNL) to evaluate the Dragos Platform on a production nuclear reactor test bed, hence laying the path for future commercial adoption. The vision was to provide a guide for industrial operators on implementing an industrial monitoring solution and to show how these solutions can be deployed without causing safety and reliability issues. This report documents the results of the collaboration between ORNL and Dragos, Inc.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multimodal analysis and characterization of the boehmite layer formed on AA6061 before and after alkaline etching

Low-enriched uranium (LEU) alloyed with 10% Mo (U-10Mo) is being considered as a promising alternative to oxide-based dispersion fuel with high-enriched uranium for use in research reactors. The configuration of this proposed LEU monolithic LEU fuel plate consists of a U-10Mo plate-type fuel foil with a 25 µm zirconium interlayer barrier clad with an aluminum alloy (AA6061). In certain research reactors, the clad AA6061 is coated with a boehmite layer to prevent corrosion. The boehmite layer has a high-pH passivation range, which makes it resistant to oxidation. Boehmite is usually formed on the AA6061 surface by autoclave processing. Before the boehmite layer is added, the surface of the AA6061 is cleaned using techniques such as polishing and wet etching. In this study, we use multimodal analysis to examine how pretreatment of AA6061 using polishing followed by alkaline etching affects the chemical composition of the boehmite layer. X-ray photoelectron microscopy (XPS), transmission electron microscopy (TEM), and x-ray diffraction (XRD) were used to study the chemical changes in the boehmite layer caused by alkaline etching pretreatment. XPS provides quantitative analysis for the Al:O ratio as well as oxidation states present on the surface, which suggests slight oxidation of the boehmite surface after alkaline etching of the AA6061 surface. We further explored this suggested oxidation of the boehmite surface using high-resolution transmission electron microscopy with selected area electron diffraction (SAED) and grazing incidence x-ray diffraction (GI-XRD), which suggested only a small amount of aluminum oxide at the surface. The multimodal analysis and imaging yielded new insights for optimizing boehmite growth on AA6061 for research reactors.

36 MATERIALS SCIENCE↗

Involute Working Group – Development and Validation of the Finite Element Models of the Cheverton-Kelley Experiments

In an involute-plate reactor, the fuel plates and side-plates are subjected to a non-uniform distribution of loads. Temperature variation derives from a variation in power distribution throughout the core. Due to small imperfections in the channel thickness, the coolant flowing in between the plates produces pressure differentials with a non-uniform distribution on the plate surface. The main goal of the analysis presented in this technical report is to investigate the ability of the commercial software STAR-CCM+ to model deformation of involute plates subjected to mechanical and thermal loads, representative of involute reactor operation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Performance of a New Composite Single-Crystal Filtered Thermal Neutron Beam for Neutron Capture Therapy Research at the University of Missouri

The University of Missouri (MU) Institute for Nano and Molecular Medicine, the Idaho National Laboratory (INL) and the University of Missouri Research Reactor (MURR) have undertaken a new collaborative research initiative to further the development of improved boron delivery agents for BNCT. The first step of this effort has involved the design and construction of a new thermal neutron beam irradiation facility for cell and small-animal radiobological research at the MURR. In this paper we present the beamline design with the results of pertinent neutronic design calculations. Results of neutronic performance measurements, initiated in February 2008, will also be available for inclusion in the final paper. The new beam will be located in an existing 152.4 mm (6’) diameter MURR beam tube extending from the core to the right in Figure 1. The neutron beam that emanates from the berylium reflector around the reactor is filtered with single-crystal silicon and single-crystal bismuth segments to remove high energy, fission spectrum neutrons and reactor gamma ray contamination. The irradiation chamber is downstream of the bismuth filter section, and approximately 3.95 m from the central axis of the reactor. There is sufficient neutron flux available from the MURR at its rated power of 10 MW to avoid the need for cryogenic cooling of the crystals. The MURR operates on average 150 hours per week, 52 weeks a year. In order to take advantage of 7800 hours of operation time per year the small animal BNCT facility will incorparate a shutter constucuted of boral, lead, steel and polyethylene that will allow experimenters to access the irradiation chamber a few minutes after irradiation. Independent deterministic and stochastic models of the coupled reactor core and beamline were developed using the DORT two-dimensional radiation transport code and the MCNP-5 Monte Carlo code, respectively. The BUGLE-80 47-neutron, 20-gamma group cross section library was employed for the DORT computations, in keeping with previous practice for analysis of a number of other NCT neutron facilities worldwide. The standard ENDF/B Version 6.8 cross section libraries were used with MCNP, except that special calculated cross section sets for the single-crystal bismuth and silicon filters in the MCNP calculations were provided to MU and INL specifically for this study by the Korean Atomic Energy Research Institute and, independently, by North Carolina State University. Cross sections for the amorphous bismuth and silicon files on the BUGLE-80 library used with DORT were modified to account for the single-crystal form of these materials using correction factors computed using MCNP. A number of parameter studies were conducted, independently varying the thicknesses of the silicon and bismuth filter sections to find an optimum that maximizes the thermal neutron flux while maintaining the fast-neutron and gamma components of the beam within acceptable ranges. Both the DORT and MCNP beamline optimization computations led to the conclusion that the silicon filtering section should be approximately 55 cm in thickness and the bismuth section should be 8 cm in thickness. The total estimated thermal neutron flux delivered to the irradiation location by the filtered beam, integrated to 0.414 eV, is approximately 9.0 x 108 neutrons/cm2-s. The calculations also yielded an epithermal and fast-neutron kerma of approximately 1.0 x 10-11 cGy-cm2.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Porosity in nuclear graphite and its impact on nuclear reactor science and criticality safety applications

Porosity in nuclear-grade graphite significantly influences its low-energy neutron scattering, yet its effect on underlying phonon properties remains debated. Here, this work integrates inelastic and small-angle neutron scattering (INS/SANS) experiments, advanced atomistic simulations with a novel machine-learned potential (DeepMD), total cross-section measurements, and neutronics calculations (SCALE, MCNP, OpenMC) to investigate porosity’s impact on neutron thermalization. INS measurements on diverse graphite grades reveal no discernible porosity effect on phonon spectra, which align with crystalline graphite. Conversely, total cross-section data below ≈10 meV show increased scattering attributable to SANS. Our DeepMD simulations demonstrate that realistic micropores do not distort phonon spectra, challenging the assumptions in current ENDF/B-VIII.1 porosity thermal scattering laws (TSLs). These TSLs, based on random atom removal, produce unphysical phonon spectra and inflate inelastic cross-sections. Augmenting a crystalline TSL with an SANS component accurately captures experimental total cross-sections. Neutronics benchmarks (ICSBEP/IRPhE) show ENDF porosity TSLs unphysically increase neutron multiplication factor, keff. Crucially, incorporating SANS physics (NCrystal/OpenMC) indicates accurately modeled porosity negligibly affects keff, reactor physics, or criticality safety.

Critical benchmarks↗

Identifying Challenges in Safeguards for Metallic Fuel Fabrication Facilities

As new advanced reactors gain popularity, there is an increasing interest in metallic fuel fabrication for fast reactors. While metallic fuels themselves are not a new idea, as many of the first reactors employed metallic fuels, new designs, compositions, and fabrication methods are appearing throughout the nuclear community. As the interest grows and facilities are constructed, both domestic and international safeguards will need to be heavily involved to support safeguards-by-design (SBD) measures from the start. This work compiles a review of historical and modern fuel types and fabrication methods, fabrication processes, safeguards gaps, and potential safeguards solutions. Metallic nuclear fuel types have been around for many decades and were included in some of the first reactors including the Experimental Breeder Reactor (EBR)-I and -II, the Fermi 1 reactor, the Integral Fast Reactor (IFR), and the Dounreay Fast Reactor (DFR). These reactors used various compositions including pure uranium (U) metal, U-zirconium (Zr) alloys, plutonium (Pu)-aluminum (Al) alloys, U-fissium (Fs) alloys, U-Pu-Zr alloys, and U-molybdenum (Mo) alloys [1, 2, 3, 4, 5]. These small alloying additions are included to improve the material properties of the pure U metal. The alpha-phase U (stable below 661C) suffers elongation in one direction causing grain boundary cracking and increasing creep rate due to irradiation growth, thermal cycling, and preferential crystal orientation. It is ideal to utilize the gamma-phase U (typically stable above 769C) by adding small amounts of alloying elements such as Zr or Mo to stabilize this phase down to room temperature [3]. Additionally, some research has been focused on U with transuranic (TRU) elements present, typically coming from the used fuel recycling process. Including these elements in fast reactor fuel can aid in the reduction of nuclear waste by burning minor long-lived actinides. However, the additions of TRU elements can cause concerns to arise when trying to fabrication or safeguard metallic fuels. A typical metallic fuel element is shown in Figure 1. Sodium is added into the cladding to create a thermal bond between the fuel slug and cladding wall. The fuel slug is then inserted and the end plug is welded on to the top of the fuel element. A gas plenum is left to create a headspace for gaseous fission products to escape rather than continue to build in the fuel itself [1, 5]. Other fuel element geometries exist as well, such as the Lightbridge twisted cruciform geometry shown in Figure 2 [6]. This design allows for better cooling performance and provides room for fuel rod swelling without impacting the fuel rod diameter. There are many different fabrication methods for metallic fuels, which is one of the many benefits of these fuel types. Many of these fabrication methods are relatively easy and cost-efficient. The most popular fabrication method is injection casting, sometimes called vacuum induction melting (VIM), shown in Figure 3 [4, 8, 9, 7, 10]. This method was largely used for EBR-II fuel fabrication. The injection casting system is contained inside of a vessel consisting of a Y2O3-coated graphite crucible surrounded by an induction coil with ZrO2-coated quartz molds suspended above the crucible. The fuel feedstock is placed inside of the graphite crucible and melted using the induction furnace. The induction furnace utilizes a dual frequency with the high frequency melting the feedstock and the low frequency causing stirring of the melted feedstock to form a homogeneous mixture. The mixture is heated to approximately 1600C in an argon environment. The vessel is evacuated and then the quartz molds are lowered into the graphite crucible containing the molten metal and the vessel is repressurized to inject the metal fuel upwards into the molds. The molds are removed and then shattered to release the fuel slugs. This fabrication method was used to fabricate 39,000 metallic fuel pins for EBR-II. While injection casting has been the most common metallic fuel fabrication method throughout the decades, many other methods have been explored including low-pressure gravity casting, microwave casting, continuous casting, centrifugal casting, coextrusion, and many others [11, 12, 8, 13, 14, 15]. Some of these methods aim to mitigate challenges that arise with americium (Am) volatilization during the casting process for TRU-containing fuel feedstocks, an issue with injection casting. Coextrusion is one of the methods explored at the Idaho National Laboratory (INL) and has been utilized for the initial fabrication tests of Lightbridge's unique fuels, as well as other metallic fuels with cladding coextruded. In this process, large billets are formed and machined and then inserted into a molten salt bath for approximately 30 minutes. The billets are then loaded into the extrusion press and extruded. This process can be seen in Figure 4 [15].

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel-rich oxidation of gasoline surrogate components in an atmospheric flow reactor

Fuel-rich oxidation of three typical gasoline surrogate components, toluene, isooctane, and n-heptane, was investigated in an atmospheric-pressure flow reactor at mean gas temperatures from 1050 to 1350 K, equivalence ratio of 9.0, and residence times of 0.45 and 1.2 s. Not only polycyclic aromatic hydrocarbons (PAHs) up to 3 ring structure but also small intermediate products from C 1 to C 5 were quantified by a gas chromatograph mass spectrometry coupled with photon ionization and gas chromatograph with flame ionization detector, respectively. The kinetic model recently developed by Lawrence Livermore National Laboratory was revised to reflect the results of many recent investigations. Basically, the updated model could satisfactorily reproduce the experimental mole fractions of many species. The experimental and simulated results showed that PAH mole fractions produced were in the order of toluene, isooctane, and n-heptane. The kinetic analysis using the model was carried out to explore PAH formation pathways, especially focusing on naphthalene, acenaphthylene, and phenanthrene. Through rate of production analysis, it was found that the main formation pathways of many PAHs were affected by the fuels. Although resonantly stabilized radicals, such as benzyl and fulvenallenyl radicals, played a crucial role in the formation pathways of many PAHs in every fuel, they were produced through hydrogen elimination of toluene in toluene fuel, while they were formed from small intermediate products in isooctane and n-heptane fuels. Sensitivity analysis revealed the difference and similarity of the reactions with large positive coefficients according to the fuels studied here. In conclusion, the molecular growth reactions of aromatic species were influential in PAH production in every fuel, whereas the ring formation reactions from small species and the reactions involving toluene had large positive sensitivity coefficients in isooctane/n-heptane and toluene fuels, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

FHR Generic Design Criteria

The purpose of this document is to provide an initial, focused reference to the safety characteristics of and a licensing approach for Fluoride-Salt-Cooled High-Temperature Reactors (FHRs). The document does not contain details of particular reactor designs nor does it attempt to identify or classify either design basis or beyond design basis accidents. Further, this document is an initial attempt by a small set of subject matter experts to document the safety and licensing characteristics of FHRs for a larger audience. The document is intended to help in setting the safety and licensing research, development, and demonstration path forward. Input from a wider audience, further technical developments, and additional study will be required to develop a consensus position on the safety and licensing characteristics of FHRs. This document begins with a brief overview of the attributes of FHRs and then a general description of their anticipated safety performance. Following this, an overview of the US nuclear power plant approval process is provided that includes both test and power reactors, as well as the role of safety standards in the approval process. The document next describes a General Design Criteria (GDC) - based approach to licensing an FHR and provides an initial draft set of FHR GDCs. The document concludes with a description of a path forward toward developing an FHR safety standard that can support both a test and power reactor licensing process.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗