Search NASA⌕ Search

SEARCH · Search NASA

Results for “Support Structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Development of an In-Situ Decommissioning Sensor Network Test Bed for Structural Condition Monitoring - 12156

The Savannah River National Laboratory (SRNL) has established an In Situ Decommissioning (ISD) Sensor Network Test Bed, a unique, small scale, configurable environment, for the assessment of prospective sensors on actual ISD system material, at minimal cost. The Department of Energy (DOE) is presently implementing permanent entombment of contaminated, large nuclear structures via ISD. The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. Validation of ISD system performance models and verification of actual system conditions can be achieved through the development a system of sensors to monitor the materials and condition of the structure. The ISD Sensor Network Test Bed has been designed and deployed to addresses the DOE-Environmental Management Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building at the Savannah River Site. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of groutable thermistors for temperature and moisture monitoring, strain gauges for crack growth monitoring, tilt-meters for settlement monitoring, and a communication system for data collection. Baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment. The Sensor Network Test Bed at SRNL uses COTS sensors on concrete blocks from the outer wall of the P Reactor Building to measure conditions expected to occur in ISD structures. Knowledge and lessons learned gained from installation, testing, and monitoring of the equipment will be applied to sensor installation in a meso-scale test bed at FIU and in future ISD structures. The initial data collected from the sensors installed on the P Reactor Building blocks define the baseline materials condition of the P Reactor ISD external concrete structure. Continued monitoring of the blocks will enable evaluation of the effects of aging on the P Reactor ISD structure. The collected data will support validation of the material degradation model and assessment of the condition of the ISD structure over time. The following are recommendations for continued development of the ISD Sensor Network Test Bed: - Establish a long-term monitoring program using the concrete blocks with existing sensor and/or additional sensors for trending the concrete materials and structural condition; - Continue development of a stand-alone test bed sensor system that is self-powered and provides wireless transmission of data to a user-accessible dashboard; - Develop and implement periodic NDE/DE characterization of the concrete blocks to provide verification and validation for the measurements obtained through the sensor system and concrete degradation model(s). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Lipocalin Blc is a potential heme-binding protein

Lipocalins are a superfamily of functionally diverse proteins defined by a well-conserved tertiary structure despite variation in sequence. Lipocalins bind and transport small hydrophobic molecules in organisms of all kingdoms. However, there is still uncertainty regarding the function of some members of the family, including bacterial lipocalin Blc from Escherichia coli. Here, we present evidence that lipocalin Blc may be involved in heme binding, trans-periplasmic transport, or heme storage. This conclusion is supported by a cocrystal structure, mass-spectrometric data, absorption titration, and in silico analysis. Binding of heme is observed at low micromolar range with one-to-one ligand-to-protein stoichiometry. However, the absence of classical coordination to the iron atom leaves the possibility that the primary ligand of Blc is another tetrapyrrole.

59 BASIC BIOLOGICAL SCIENCES↗

Redox-dependent rearrangements of the NiFeS cluster of carbon monoxide dehydrogenase

The C-cluster of the enzyme carbon monoxide dehydrogenase (CODH) is a structurally distinctive Ni-Fe-S cluster employed to catalyze the reduction of CO2 to CO as part of the Wood-Ljungdahl carbon fixation pathway. Using X-ray crystallography, we have observed unprecedented conformational dynamics in the C-cluster of the CODH from Desulfovibrio vulgaris, providing the first view of an oxidized state of the cluster. Combined with supporting spectroscopic data, our structures reveal that this novel, oxidized cluster arrangement plays a role in avoiding irreversible oxidative degradation at the C-cluster. Furthermore, mutagenesis of a conserved cysteine residue that binds the C-cluster in the oxidized state but not in the reduced state suggests that the oxidized conformation could be important for proper cluster assembly, in particular Ni incorporation. Together, these results lay a foundation for future investigations of C-cluster activation and assembly, and contribute to an emerging paradigm of metallocluster plasticity.

Wittenborn, Elizabeth C.↗

Local observation of linear-T superfluid density and anomalous vortex dynamics in URu2Si2

The heavy fermion superconductor URu2Si2 is a candidate for chiral, time-reversal symmetry-breaking superconductivity with a nodal gap structure. Here, we microscopically visualized superconductivity and spatially inhomogeneous ferromagnetism in URu2Si2. We observed linear-T superfluid density, consistent with d-wave pairing symmetries including chiral d wave, but did not observe the spontaneous magnetization expected for chiral d wave. Local vortex pinning potentials had either four- or twofold rotational symmetries with various orientations at different locations. Taken together, these data support a nodal gap structure in URu2Si2 and suggest that chirality either is not present or does not lead to detectable spontaneous magnetization.

36 MATERIALS SCIENCE↗

Metal–Organic Framework Nodes as a Supporting Platform for Tailoring the Activity of Metal Catalysts

Catalysis is a ubiquitous element of the modern economy, representing a cornerstone of many sectors including energy, materials, and pharmaceuticals. Within this realm, 80% of reactions are carried out by heterogeneous catalysts due to their advantageous physical and chemical characteristics. In some heterogeneous systems, the reaction rate can be optimized through rational catalyst design, in which support materials can be tailored structurally and stereoelectronically for targeted purposes to better facilitate the catalytic reaction. To this end, metal-organic frameworks (MOFs) have garnered recent attention due to their high porosity, crystallinity, and chemical tunability, which can be used to derive structure-activity relationships in the design of catalysts. In this Perspective, we survey examples of catalytically active guest metals on the inorganic nodes of MOFs. This is done with the intention of providing design guidelines for tailoring chemical reactivity and insights into the opportunities for future growth in this field. Strategies for rational design in MOF catalysis include electronic tuning of the metal node in the MOF support, installing promoter ions onto the node to effect the reactivity of grafted metals, modulation of the spatial environment around the transition metal using the metal node structure, and achieving site uniformity in supported catalysts. By highlighting these efforts, we seek to underscore the role of MOF nodes as nonspectator supports for catalytic metal complexes and provide future directions for rational catalyst design by tuning reactivity on these anchoring platforms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Discovery and Characterization of a Metastable Cubic Interstitial Nickel–Carbon System with an Expanded Lattice

Metastable, i.e., kinetically favored but thermodynamically not stable, interstitial solid solutions of carbon in iron are well-understood. Carbon can occupy the interstitial atoms of the host metal, altering its properties. Alloying of the host metal results in the stabilization of the FeC x phases, widening its application. Pure nickel finds niche applications, mainly focusing on catalysis, while nickel alloys are widely applied, e.g., in gas turbines, reactors, and seawater piping. Nickel carbide (Ni 3 C) is the well-known stable Ni–C system displaying a rhombohedral (R3̅c) crystal structure. Some reports describe an elusive cubic Ni–C system, observed during certain catalytic reactions occurring on nickel and formed by the occupation of the interstitials of the metal with carbon: to date, the stabilization and characterization of this phase have not been accomplished. Hereby, we report on the synthesis of a cubic metastable NiC x phase using chemical vapor deposition of methane on supported nickel nanoparticles. The structure was predicted by DFT/ReaxFF, synthesized and monitored with in situ time-resolved synchrotron XRD, and experimentally confirmed by Rietveld refinement and (S)TEM-EELS under ambient conditions. The results show an Fm3̅m phase with a lattice parameter of a = 3.749 ± 0.037 Å at room temperature, with the highest ever reported atomic percentage of carbon occupying the octahedral interstices of 23.1%, resulting in a NiC 0.3 phase. The degree of occupation of the interstitial voids by carbon can be controlled, enabling the tuning of the host metal’s d-spacing and composition, highlighting the applicability of this synthesis route for catalytic nanoparticle preparation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A first-principles study of Pt thin films on SrTiO{sub 3}(100): Support effects on CO adsorption

Density functional theory was used to study CO adsorption on thin Pt metal films supported on SrO- and TiO{sub 2}-terminated SrTiO{sub 3}(100) surfaces. Regardless of substrate-termination, significant enhancement in CO binding occurred on the Pt monolayer compared to the bulk Pt(100) surface. We also observed CO-coverage dependent shifting of Pt atoms, influenced by the nature of underlying oxide atoms. These oxide-induced effects become negligible after depositing more than 2 monolayers of Pt. Evaluating the electronic structures of oxide-supported Pt showed that the interaction of filled Pt d{sub xz+yz} and empty Pt d{sub z{sup 2}} states with CO molecular orbitals can be directly related to CO adsorption on the Pt/SrTiO{sub 3}(100) surface. A hybrid d-band model is able to capture the CO adsorption trends for systems that do not show large lateral distortion except for the case of Pt adsorbed above the Sr atom on the SrO-termination. For this case, charge transfer from adjacent Pt atoms leads to a large filled d{sub z{sup 2}} peak below the Fermi level that weakens the Pt–CO σ bonding due to Pauli repulsion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineered Nano-Scale Ceramic Supports for PEM Fuel Cells

Development of electronically conductive ceramic materials is of fundamental importance to a wide variety of applications. One application of particular interest is proton exchange membrane fuel cells (PEMFC), where strong oxidizing conditions exist, especially in the cathode. The reaction that takes place in the cathodic side of PEMFCs is the oxygen reduction reaction (ORR) which is considered to be kinetically sluggish and thus, it is catalyzed, usually by platinum nano-particles. Due to the high cost of such catalysts, and in order to maintain their optimized nano-crystallite structure, they are normally supported on a relatively cheap, electronically conductive, porous, high surface area support. Most of the electrode support materials used in fuel cells today are carbon based which are highly sensitive to corrosive conditions and thus corrode under normal fuel cell operating conditions. This leads to processes that can be detrimental to the fuel cell and is manifested in the form of loss of surface area, impediment of mass transport and loss of catalyst activity due to sintering or dissolution. The direct consequence of these effects is the loss of the overall fuel cell power output overtime and shortening their lifetime; both make this technology less attractive to industry. In order to make PEMFCs more viable, it is necessary to extend their lifetime and reliability by improving the catalyst support.

08 HYDROGEN↗

Preliminary Design of JLAB Clas12 Large Superconducting Torus Magnet

Hall B at Jefferson Laboratory (JLAB) will need a 6-coil Torus producing a required integral of B-dl for an upgrade 12 GeV beam. In Sept. 2009, Wang NMR was awarded a contract to design, fabricate, assemble, deliver, and test at JLAB this ex citing magnet. The preliminary design review was completed by Dec. 2009 and intermediate design review will be completed by July 2010. Proto type coil construction, production of soldered conductor with SSC cable and final design review will be completed in 2010. We shall describe preliminary design and intermediate design for coil/cryostat, Torus central cylinder (hub), 48 cold mass suspensions, two intercoil support rings, cryocontrol tower, and adapter to Torus coil, magnet quench protection, and charge/ discharge con trol, and the two parallel path cooling design using supercritical helium. Because of coil in-plane and out-of-plane EM forces over these huge thin coils in addition to vacuum load, gravity load, and cool down thermal stress, we shall present the finite element analyses (FEA) on coil structure, 48 cold mass supports, intercoil cold rings, coil/ cryostat vacuum vessel, cryotower cryostat, and Torus hub. Finally, we shall shows that all pressure/ vacuum vessels and its weldment has satisfied ASME code.

43 PARTICLE ACCELERATORS↗

Structure and Vibrational Properties of Potassium-Promoted Tungsten Oxide Catalyst Monomeric Sites Supported on Alumina (K 2 O/WO 3 /Al 2 O 3 ) Characterized Using Periodic Density Functional Theory

Al 2 O 3 -supported tungsten oxide catalysts have been instrumental in many industrially relevant reactions and their reactivity is controlled by their molecular structure. In turn, their molecular structure has primarily been derived via Raman measurements with assignments made using model compounds of known local (molecular) coordination. Here, the structure and simulated Raman spectra of unpromoted and K + -promoted tungsten oxide catalyst monomeric sites supported on γ-Al 2 O 3 (110) (K 2 O/WO x /γ-Al 2 O 3 (110)) were studied using periodic DFT methods. Two different WO x -grafted monomers on the γ-Al 2 O 3 (110) surface were identified with a total energy difference of 0.17 eV between both structures. Importantly, both structures showed the presence of W═O and W–OH moieties, thus providing additional insights into experimental Raman data, which typically describe only W═O moieties. The grafted WO 3 species were stabilized when the present W–OH groups were oriented toward the alumina surface leading to the formation of H-bonds, calculated at 1039 cm –1 , for example in the vicinity of the W═O vibrations. The W═O bond length was altered in the presence of K + , as shown experimentally and theoretically in blue shifting of the Raman band corresponding to W═O. The W vibrations were well localized in the calculated spectra, and little shifts were observed upon the different WO x molecular geometry, explaining why a single Raman peak is mostly observed experimentally. The acidity of the lowest energy catalyst structures was investigated by simulated NH 3 adsorption vibrational frequency and binding energy calculations. Results suggested that NH 3 prefers to bind in a Lewis-like structure with no proton donation from either W–OH or Al–OH moiety. This challenged some of the literature observations where Brønsted acid sites have been suggested to exist on near-monolayer coverage WO x species on γ-Al 2 O 3 prepared by calcining at moderate (400 °C) to high temperatures (700 °C). Finally, this work provided new insights into the molecular structure of WO x /γ-Al 2 O 3 and K 2 O/WO x /γ-Al 2 O 3 catalysts not immediately available from experimental measurements alone.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Localized Electronic States from Surface Hydroxyls and Polarons in TiO2(110)

Hydroxyls on a TiO2 surface and photo-induced e- polarons give rise to excess charges, the electronic structure of which is critical to the fundamental understanding of their role in the reactivity of surface absorbates and other photochemical processes. In this paper we studied the electronic structure of one excess electron in bare surfaces and surfaces with a single hydroxyl, in particular for the rutile (110) surface. The DFT+U electronic structure is one of a small polaron with its spin density and associated lattice distortion localized around a single site. Calculations indicate that the most stable Ti site in both bare and hydroxylated surfaces resides in the first sub-surface layer under the Ti5c row. The energy differences between several Ti sites are within 0.2 eV indicating that the Boltzmann population of these sites is significant at room temperature and that the excess electron will appear as fractionally occupying several sites. Based on earlier calculations the activation barrier for electron hopping from site to site is small, less than 0.1 eV, The stability ordering of the different Ti sites are very similar for the bare and hydroxylated surface, suggesting that the hydroxyl only weakly perturbs the surface electronic structure. This work was supported by the U.S. Department of Energy's Office of Basic Energy Sciences' Chemical Scienses program. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Thermodynamics of the S 2 -to-S 3 state transition of the oxygen-evolving complex of photosystem II

The room temperature pump–probe X-ray free electron laser (XFEL) measurements used for serial femtosecond crystallography provide remarkable information about the structures of the catalytic (S-state) intermediates of the oxygen-evolution reaction of photosystem II. However, mixed populations of these intermediates and moderate resolution limit the interpretation of the data from current experiments. The S 3 XFEL structures show extra density near the OEC that may correspond to a water/hydroxide molecule. However, in the latest structure, this additional oxygen is 2.08 Å from the Oε2 of D1–E189, which is closer than the sum of the van der Waals radii of the two oxygens. In this work, we use Boltzmann statistics and Monte Carlo sampling to provide a model for the S 2 -to-S 3 state transition, allowing structural changes and the insertion of an additional water/hydroxide. Based on our model, water/hydroxide addition to the oxygen-evolving complex (OEC) is not thermodynamically favorable in the S 2 g = 2 state, but it is in the S 2 g = 4.1 redox isomer. Thus, formation of the S 3 state starts by a transition from the S 2 g = 2 to the S 2 g = 4.1 structure. Then, electrostatic interactions support protonation of D1–H190 and deprotonation of the Ca 2+ -ligated water (W3) with proton loss to the lumen. The W3 hydroxide moves toward Mn4, completing the coordination shell of Mn4 and favoring its oxidation to Mn( IV ) in the S 3 state. In addition, binding an additional hydroxide to Mn1 leads to a conformational change of D1–E189 in the S 2 g = 4.1 and S 3 structures. In the S 3 state a fraction of D1–E189 release from Mn1 and bind a proton.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural basis of the Cks1-dependent recognition of p27(Kip1) by the SCF(Skp2) ubiquitin ligase

The ubiquitin-mediated proteolysis of the Cdk2 inhibitor p27{sup Kip1} plays a central role in cell cycle progression, and enhanced degradation of p27{sup Kip1} is associated with many common cancers. Proteolysis of p27{sup Kip1} is triggered by Thr187 phosphorylation, which leads to the binding of the SCF{sup Skp2} (Skp1-Cul1-Rbx1-Skp2) ubiquitin ligase complex. Unlike other known SCF substrates, p27{sup Kip1} ubiquitination also requires the accessory protein Cks1. The crystal structure of the Skp1-Skp2-Cks1 complex bound to a p27{sup Kip1} phosphopeptide shows that Cks1 binds to the leucine-rich repeat (LRR) domain and C-terminal tail of Skp2, whereas p27{sup Kip1} binds to both Cks1 and Skp2. The phosphorylated Thr187 side chain of p27{sup Kip1} is recognized by a Cks1 phosphate binding site, whereas the side chain of an invariant Glu185 inserts into the interface between Skp2 and Cks1, interacting with both. The structure and biochemical data support the proposed model that Cdk2-cyclin A contributes to the recruitment of p27{sup Kip1} to the SCF{sup Skp2}-Cks1 complex.

36 MATERIALS SCIENCE↗

MASS-RADIUS RELATIONSHIPS FOR EXOPLANETS

For planets other than Earth, particularly exoplanets, interpretation of the composition and structure depends largely on comparing the mass and radius with the composition expected given their distance from the parent star. The composition implies a mass-radius relation which relies heavily on equations of state calculated from electronic structure theory and measured experimentally on Earth. We lay out a method for deriving and testing equations of state, and deduce mass-radius and mass-pressure relations for key, relevant materials whose equation of state (EOS) is reasonably well established, and for differentiated Fe/rock. We find that variations in the EOS, such as may arise when extrapolating from low-pressure data, can have significant effects on predicted mass-radius relations and on planetary pressure profiles. The relations are compared with the observed masses and radii of planets and exoplanets, broadly supporting recent inferences about exoplanet structures. Kepler-10b is apparently 'Earth-like', likely with a proportionately larger core than Earth's, nominally 2/3 of the mass of the planet. CoRoT-7b is consistent with a rocky mantle over an Fe-based core which is likely to be proportionately smaller than Earth's. GJ 1214b lies between the mass-radius curves for H{sub 2}O and CH{sub 4}, suggesting an 'icy' composition with a relatively large core or a relatively large proportion of H{sub 2}O. CoRoT-2b is less dense than the hydrogen relation, which could be explained by an anomalously high degree of heating or by higher than assumed atmospheric opacity. HAT-P-2b is slightly denser than the mass-radius relation for hydrogen, suggesting the presence of a significant amount of matter of higher atomic number. CoRoT-3b lies close to the hydrogen relation. The pressure at the center of Kepler-10b is 1.5{sup +1.2}{sub -1.0} TPa. The central pressure in CoRoT-7b is probably close to 0.8 TPa, though may be up to 2 TPa. These pressures are accessible by planar shock and ramp-loading experiments at large laser facilities. The center of HAT-P-2b is probably around 210 TPa, in the range of planned National Ignition Facility experiments, and that of CoRoT-3b around 1900 TPa.

79 ASTRONOMY AND ASTROPHYSICS↗

Tetrahedral triple-Q magnetic ordering and large spontaneous Hall conductivity in the metallic triangular antiferromagnet Co 1/3 TaS 2

The triangular lattice antiferromagnet (TLAF) has been the standard paradigm of frustrated magnetism for several decades. The most common magnetic ordering in insulating TLAFs is the 120° structure. However, a new triple-Q chiral ordering can emerge in metallic TLAFs, representing the short wavelength limit of magnetic skyrmion crystals. We report the metallic TLAF Co 1 / 3 TaS 2 as the first example of tetrahedral triple-Q magnetic ordering with the associated topological Hall effect (non-zero σ xy (H = 0)). We also present a theoretical framework that describes the emergence of this magnetic ground state, which is further supported by the electronic structure measured by angle-resolved photoemission spectroscopy. Additionally, our measurements of the inelastic neutron scattering cross section are consistent with the calculated dynamical structure factor of the tetrahedral triple-Q state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Crystal Structure of Vancosaminyltransferase GtfD from the Vancomycin Biosynthetic Pathway: Interactions with Acceptor and Nucleotide Ligands

The TDP-vancosaminyltransferase GtfD catalyzes the attachment of L-vancosamine to a monoglucosylated heptapeptide intermediate during the final stage of vancomycin biosynthesis. Glycosyltransferases from this and similar antibiotic pathways are potential tools for the design of new compounds that are effective against vancomycin resistant bacterial strains. We have determined the X-ray crystal structure of GtfD as a complex with TDP and the natural glycopeptide substrate at 2.0 {angstrom} resolution. GtfD, a member of the bidomain GT-B glycosyltransferase superfamily, binds TDP in the interdomain cleft, while the aglycone acceptor binds in a deep crevice in the N-terminal domain. However, the two domains are more interdependent in terms of substrate binding and overall structure than was evident in the structures of closely related glycosyltransferases GtfA and GtfB. Structural and kinetic analyses support the identification of Asp13 as a catalytic general base, with a possible secondary role for Thr10. Several residues have also been identified as being involved in donor sugar binding and recognition.

36 MATERIALS SCIENCE↗

Correlated Anion Disorder in Heteroanionic Cubic TiOF 2

Resolving anion configurations in heteroanionic materials is crucial for understanding and controlling their properties. For anion-disordered oxyfluorides, conventional Bragg diffraction cannot fully resolve the anionic structure, necessitating alternative structure determination methods. We have investigated the anionic structure of anion-disordered cubic (ReO 3 -type) TiOF 2 using X-ray pair distribution function (PDF), 19 F MAS NMR analysis, density functional theory (DFT), cluster expansion modeling, and genetic-algorithm structure prediction. Our computational data predict short-range anion ordering in TiOF 2 , characterized by predominant cis-[O 2 F 4 ] titanium coordination, resulting in correlated anion disorder at longer ranges. To validate our predictions, we generated partially disordered supercells using genetic-algorithm structure prediction and computed simulated X-ray PDF data and 19 F MAS NMR spectra, which we compared directly to experimental data. To construct our simulated 19 F NMR spectra, we derived new transformation functions for mapping calculated magnetic shieldings to predicted magnetic chemical shifts in titanium (oxy)fluorides, obtained by fitting DFT-calculated magnetic shieldings to previously published experimental chemical shift data for TiF 4 . We find good agreement between our simulated and experimental data, which supports our computationally predicted structural model and demonstrates the effectiveness of complementary experimental and computational techniques in resolving anionic structure in anion-disordered oxyfluorides. From additional DFT calculations, we predict that increasing anion disorder makes lithium intercalation more favorable by, on average, up to 2 eV, highlighting the significant effect of variations in short-range order on the intercalation properties of anion-disordered materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanostructured carbon electrocatalyst supports for intermediate-temperature fuel cells: Single-walled versus multi-walled structures

It is unknown if nanostructured carbons possess the requisite electrochemical stability to be used as catalyst supports in the cathode of intermediate-temperature solid acid fuel cells (SAFCs) based on the CsH2PO4 electrolyte. To investigate this application, single-walled carbon nanohorns (SWNHs) and multi-walled carbon nanotubes (MWNTs) were used as supports for Pt catalysts in SAFCs operating at 250 °C. SWNH-based cathodes display greater maximum activity than their MWNT-based counterparts at a cell voltage of 0.8 V, but are unstable in the SAFC cathode as a consequence of electrochemical carbon corrosion. MWNT-based cells are resistant to this effect and capable of operation for at least 160 h at 0.6 V and 250 °C. Cells fabricated with nanostructured carbon supports are more active (52 mA cm -1 vs. 28 mA cm -1 at 0.8 V) than state-of-the-art carbon-free formulations while simultaneously displaying enhanced Pt utilization (40 mA mgPt -1 vs. 16 mA mgPt -1 at 0.8 V). Finally, these results suggest that MWNTs are a viable support material for developing stable, high-performance, low-cost air electrodes for solid-state electrochemical devices operating above 230 °C.

25 ENERGY STORAGE↗