Search NASA⌕ Search

SEARCH · Search NASA

Results for “UTILITY PROGRAM DESIGN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Study of aerodynamic technology for VSTOL fighter/attack aircraft, volume 1

An assessment was made of the aerodynamic uncertainties associated with the design of a cold-deck-environment Navy VSTOL fighter/attack aircraft utilizing jet-diffuser ejectors for vertical lift and vectored-engine-over-wing blowing for supercirculation benefits. The critical aerodynamic uncertainties were determined as those associated with the constraints which size the aircraft to a specified set of requirements. A wind tunnel model and test programs are recommended for resolving these uncertainties.

Lummus, J. R.↗
NASA NTRS1982

High voltage distribution and grounding in high power spacecraft

Many space missions proposed for the time period from 1985 to 2000 will require large spacecraft to support the onboard loads. In some cases, large electrical power systems will be needed to supply the electrical/electronic equipment loads. These electronic systems will be used for communications, radar, and experimental equipment for aid to earth's overcrowded communication systems, exploration of new energy resources, space exploration, and eventually to supplement terrestrial electric power utilities. For the near term (1985-1990), some of these systems have power levels to 50 kW. The long-term programs, 1990 to post-2000, could possibly have demands in the order of multimegawatts. The problems which have to be solved to construct the required high-voltage power supply systems are considered. Data and conceptual designs generated are found to indicate that grounding and bonding for high power systems can be accomplished in spacecraft by using either manual or automatic joining of the structural members.

Dunbar, W. G.↗
NASA NTRS1984

A new concept for exhaust diffusers of altitude test cells

A new exhaust diffuser concept for jet engine altitude test cells which greatly reduces operating power and cost requirements for exhausters is discussed. The concept utilizes the capture duct as an efficient diffuser only, while evacuating the secondary air via a separate path using an auxiliary suction system. Implementation of the concept would reduce the peak exhauster power requirement during a TF-30 altitude test by 48 percent and the overall exhaust power cost of the test program by 41 percent. The design accommodates various engine sizes and can achieve optimum pressure recovery performance during both A/B and IRP modes of engine operation. The pressure recovery performance of the proposed exhaust diffusers does not deteriorate with increasing cooling air fraction. The disadvantages of the proposed scheme are: increased mechanical complexity of the extended variable geometry diffuser duct and the need for an auxiliary suction system for evacuating cell-cooling air.

Parikh, P. G.↗
NASA NTRS1986

Technical aspects of the United States Space Station

The design and development of the Space Station are described. The proposed design of the Station is a dual keel configuration which will include manned facilities and unmanned free flying platforms. The Station is to be utilized as a space-based laboratory for basic research and observations, a depot for repair and servicing of spacecraft, a strorage area, and a manufacturing facility. International participation in the Space Station program and technological developments applicable for the Station are discussed. A diagram of the Space Station configuration and a Space Station development schedule are provided.

Herman, D. H.↗
NASA NTRS1988

HOST turbine heat transfer program summary

The objectives of the HOST Turbine Heat Transfer subproject were to obtain a better understanding of the physics of the aerothermodynamic phenomena and to assess and improve the analytical methods used to predict the flow and heat transfer in high temperature gas turbines. At the time the HOST project was initiated, an across-the-board improvement in turbine design technology was needed. A building-block approach was utilized and the research ranged from the study of fundamental phenomena and modeling to experiments in simulated real engine environments. Experimental research accounted for approximately 75 percent of the funding with the remainder going to analytical efforts. A healthy government/industry/university partnership, with industry providing almost half of the research, was created to advance the turbine heat transfer design technology base.

Heat transfer↗
NASA NTRS1988

The design and performance of a modem for land mobile satellite communications

The digital implementation and performance of a multipath fade-tolerant differentially coherent 8-PSK-based modem for a land mobile satellite experiment (MSAT-X) program is described. At the receiver, differential detection using a matched filter arrangement and feedforward Doppler compensation is employed to achieve several operational benefits. For this L-band satellite link, the channel utilization is an efficient 1.0 bps/Hz for raw data and 1.5 bps/Hz for coded data. The experimental data analysis shows that the modem functions over the fading channel and performs within 1 dB of theoretical or simulation estimates.

Jedrey, T. C.↗
NASA NTRS1998

Variable-Complexity Multidisciplinary Optimization on Parallel Computers

This report covers work conducted under grant NAG1-1562 for the NASA High Performance Computing and Communications Program (HPCCP) from December 7, 1993, to December 31, 1997. The objective of the research was to develop new multidisciplinary design optimization (MDO) techniques which exploit parallel computing to reduce the computational burden of aircraft MDO. The design of the High-Speed Civil Transport (HSCT) air-craft was selected as a test case to demonstrate the utility of our MDO methods. The three major tasks of this research grant included: development of parallel multipoint approximation methods for the aerodynamic design of the HSCT, use of parallel multipoint approximation methods for structural optimization of the HSCT, mathematical and algorithmic development including support in the integration of parallel computation for items (1) and (2). These tasks have been accomplished with the development of a response surface methodology that incorporates multi-fidelity models. For the aerodynamic design we were able to optimize with up to 20 design variables using hundreds of expensive Euler analyses together with thousands of inexpensive linear theory simulations. We have thereby demonstrated the application of CFD to a large aerodynamic design problem. For the predicting structural weight we were able to combine hundreds of structural optimizations of refined finite element models with thousands of optimizations based on coarse models. Computations have been carried out on the Intel Paragon with up to 128 nodes. The parallel computation allowed us to perform combined aerodynamic-structural optimization using state of the art models of a complex aircraft configurations.

Grossman, Bernard↗
NASA NTRS2001

3D Simulation: Microgravity Environments and Applications

Most, if not all, 3-D and Virtual Reality (VR) software programs are designed for one-G gravity applications. Space environments simulations require gravity effects of one one-thousandth to one one-million of that of the Earth's surface (10(exp -3) - 10(exp -6) G), thus one must be able to generate simulations that replicate those microgravity effects upon simulated astronauts. Unfortunately, the software programs utilized by the National Aeronautical and Space Administration does not have the ability to readily neutralize the one-G gravity effect. This pre-programmed situation causes the engineer or analysis difficulty during micro-gravity simulations. Therefore, microgravity simulations require special techniques or additional code in order to apply the power of 3D graphic simulation to space related applications. This paper discusses the problem and possible solutions to allow microgravity 3-D/VR simulations to be completed successfully without program code modifications.

Hunter, Steve L.↗
NASA NTRS1992

Small Business Innovations

The purpose of QASE RT is to enable system analysts and software engineers to evaluate performance and reliability implications of design alternatives. The program resulted from two Small Business Innovation Research (SBIR) projects. After receiving a description of the system architecture and workload from the user, QASE RT translates the system description into simulation models and executes them. Simulation provides detailed performance evaluation. The results of the evaluations are service and response times, offered load and device utilizations and functional availability.

Source record↗
NASA NTRS2002

On Using Commercial Off-the-Shelf (COTS) Electronic Products in Space

NASA's Johnson Space Center (JSC) has utilized COTS products in its programs since the early 1990's. Recently it has become evident that, of all failure modes possible, radiation will probably dominate; sometimes to the point of driving system architecture. It is now imperative that radiation susceptibility be addressed when writing the system requirements. Susceptibility assessment, e.g. testing, must begin early in the design phase to establish performance and continue through the hardware qualification program to prove satisfaction of the original requirements(s). Examples of requirements, testing, and architecture versus failure rate will be given.

Culpepper, William X.↗
NASA NTRS2015

Radioisotope Power Systems Reference Book for Mission Designers and Planners

The RPS Program's Program Planning and Assessment (PPA) Office commissioned the Mission Analysis team to develop the Radioisotope Power Systems (RPS) Reference Book for Mission Planners and Designers to define a baseline of RPS technology capabilities with specific emphasis on performance parameters and technology readiness. The main objective of this book is to provide RPS technology information that could be utilized by future mission concept studies and concurrent engineering practices. A progress summary from the major branches of RPS technology research provides mission analysis teams with a vital tool for assessing the RPS trade space, and provides concurrent engineering centers with a consistent set of guidelines for RPS performance characteristics. This book will be iterated when substantial new information becomes available to ensure continued relevance, serving as one of the cornerstone products of the RPS PPA Office. This book updates the original 2011 internal document, using data from the relevant publicly released RPS technology references and consultations with RPS technologists. Each performance parameter and RPS product subsection has been reviewed and cleared by at least one subject matter representative. A virtual workshop was held to reach consensus on the scope and contents of the book, and the definitions and assumptions that should be used. The subject matter experts then reviewed and updated the appropriate sections of the book. The RPS Mission Analysis Team then performed further updates and crosschecked the book for consistency. Finally, a second virtual workshop was held to ensure all subject matter experts and stakeholders concurred on the contents.

Lee, Young↗
NASA NTRS2018

Introduction to Medical Extensible Dynamic Probabilistic Risk Assessment Tool (MEDPRAT)

A key component in the development of NASA Human Research Programs (HRP) next generation risk model, the Medical Extensible Dynamic Probabilistic Risk Assessment Tool (MEDPRAT) intends to deliver a means to quantify how HRP products impact astronaut medical and health risks. MEDPRAT is extensible to the majority of exploration missions. Similar to other risk models, the tool utilizes the available space and terrestrial medical data. MEDPRAT is designed to be extended with additional human health research information, medical equipment, space and terrestrial standards and practices to assess space flight medical risk in a manner consistent with other risk measures used in spacecraft and mission design. This tool provides risk-based medical system design information necessary to evaluate new technologies, procedures, research insights and mission plans.

physiological response↗
NASA NTRS2019

Maturation of Dynamic Power Convertors for Radioisotope Power Systems

Dynamic Radioisotope Power Systems (DRPS) are being developed by NASA’s Radioisotope Power Systems (RPS) Program in collaboration with the U.S. Department of Energy (DOE) for space science and exploration missions. A development effort is currently underway to mature dynamic power convertors for infusion into a potential future flight generator. This convertor maturation effort was formulated by the RPS Program at NASA Headquarters based on successful maturation models and utilizes expertise from agency’s technology and mission centers to support requirements development and technology assessments. The effort is being executed by Glenn Research Center’s (GRC) DRPS Project and the Thermal Energy Conversion Branch. The Dynamic Power Convertor (DPC) contracts consist of three phases to enable design, fabrication, and independent assessment of prototypes after delivery to the government. The contracts are intended to gather data on candidate dynamic conversion technologies to fill knowledge gaps, support assessments of dynamic conversion technologies, and elicit generator requirements. The 110-watt Stirling Radioisotope Generator (SRG-110) and Advanced Stirling Radioisotope Generator (ASRG) flight development projects provided Stirling convertor demonstration units and engineering models to verify and validate convertors against performance specifications and mission requirements. These units utilize temperature resistant materials and non-contacting bearings to demonstrate wear-free, long-life operation. This maturation effort builds on past lessons-learned and new requirements focused on demonstrating convertor robustness to critical environments meant to stress key aspects of each convertor within the margins of the design. This effort seeks to realize the full potential of dynamic power conversion technologies for NASA’s space science and exploration missions.

Wilson, Scott↗
DOE OSTI2024

Elevated Temperature Graphite Mechanical Testing

High purity graphite will be used for core components within most High Temperature Reactor (HTR) designs. Several "high tech” industries currently utilize synthetic, high-purity, commercially available graphite components to fabricate photovoltaic cells, semi-conductors, optical fibers, and other high value electronic industry products. New advanced HTR designs are also interested in using these graphite grades for long-term, internal core component applications. Consequently, the US Department of Energy, Advanced Reactor Technologies (DOE-ART) program has spent several years testing different high purity graphite grades for potential use within these new nuclear reactor designs. A significant part of that effort has been in the development and improvement of American Society for Testing and Materials (ASTM) test standards specifically for nuclear graphite grades. Nearly all ASTM test standards have either been developed or improved by the DOE-ART program over the past 25 years. The ART program continues to assist in the development of new ASTM test standards in support of the future commercial HTR fleet currently being designed and built in the USA. The newest effort undertaken by ART is the development of high temperature mechanical testing practices that may be acceptable for a future ASTM test standard (or guide) for this critical material property measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Space Station utilization

The essential requirement of the Space Station that the customer be continually involved in all aspects of the program is considered. Potential users of the Space Station need both formal and informal channels into the program at an early stage of the definition process to secure their influence and participation in the development process. Only with this participation can users' needs and requirements be integrated into the design phase to produce 'user friendliness' in the Space Station. A Space Station that is easy and economical to use will generate more users that can take advantage of the available resources. The Space Station must be: a research facility; a satellite servicing and assembly facility; an observatory for terrestrial, solar, and astronomical viewing; and a transportation node for orbit transfer vehicles. NASA intends to see that the Space Station is developed and operated so as to serve its users.

Raney, W. P.↗
NASA NTRS2019

An Exploration of Mission Concepts That Could Utilize Small RPS

The NASA Radioisotope Power Systems (RPS) Program Mission Analysis Team at the Jet Propulsion Laboratory (JPL) requested a JPL Innovation Foundry Architecture Team (A-Team) study to assess mission pull for small RPS (1 mWe - 40 We) in order to inform the RPS Program Office on what future power system developments should be focused on. The A-Team is JPL’s concurrent engineering design team for science definition and early mission concept development, targeting concept maturation levels of 1 through 3. The requested small RPS study was tasked to identify the architecture space of potential small RPS missions, and suggest power levels that could enable or enhance potential future small spacecraft missions. This paper describes the collaborative engineering processes that the A-Team and Mission Analysis Team used to reach results quickly and the findings to inform the RPS Program about mission concept power requirements on RPS for small missions.

Bairstow, Brian K.↗
NASA NTRS2009

Controlling Infrastructure Costs: Right-Sizing the Mission Control Facility

Johnson Space Center's Mission Control Center is a space vehicle, space program agnostic facility. The current operational design is essentially identical to the original facility architecture that was developed and deployed in the mid-90's. In an effort to streamline the support costs of the mission critical facility, the Mission Operations Division (MOD) of Johnson Space Center (JSC) has sponsored an exploratory project to evaluate and inject current state-of-the-practice Information Technology (IT) tools, processes and technology into legacy operations. The general push in the IT industry has been trending towards a data-centric computer infrastructure for the past several years. Organizations facing challenges with facility operations costs are turning to creative solutions combining hardware consolidation, virtualization and remote access to meet and exceed performance, security, and availability requirements. The Operations Technology Facility (OTF) organization at the Johnson Space Center has been chartered to build and evaluate a parallel Mission Control infrastructure, replacing the existing, thick-client distributed computing model and network architecture with a data center model utilizing virtualization to provide the MCC Infrastructure as a Service. The OTF will design a replacement architecture for the Mission Control Facility, leveraging hardware consolidation through the use of blade servers, increasing utilization rates for compute platforms through virtualization while expanding connectivity options through the deployment of secure remote access. The architecture demonstrates the maturity of the technologies generally available in industry today and the ability to successfully abstract the tightly coupled relationship between thick-client software and legacy hardware into a hardware agnostic "Infrastructure as a Service" capability that can scale to meet future requirements of new space programs and spacecraft. This paper discusses the benefits and difficulties that a migration to cloud-based computing philosophies has uncovered when compared to the legacy Mission Control Center architecture. The team consists of system and software engineers with extensive experience with the MCC infrastructure and software currently used to support the International Space Station (ISS) and Space Shuttle program (SSP).

Martin, Keith↗
NASA NTRS1998

Arcjet Semi-Elliptic Nozzle Simulations and Validation in Support of TPS Testing

Much of the ground based testing of advanced thermal protection system (TPS) components for the X33 program is done in arc-heated wind tunnels such as those located in the Arc-Jet Complex at NASA Ames Research Center. These facilities are capable of simulating the high temperature, chemically reacting flow environment experienced by the vehicle during flight. This allows one to test critical design issues such as maximum reuse temperatures, seals, gaps, and increases in heating due to interfaces between different materials. Computational fluid dynamics (CFD) has evolved to the point where it now can be used in the vehicle design process for accurate and timely prediction of trajectory based aerothermal heating environments for re-entry vehicles. It can also be used for simulation of the flow environments in ground based facilities such as arcjets. By utilization of the same CFD code and solution methodology, the important differences between ground test and flight may be quantified. The goal of this paper is to utilize CFD to provide validated simulations of the flow environment in the NASA-Ames semi elliptic nozzle arcjet facilities. The validation of the ground simulations will come From comparison to existing calibration data. Specific tests in support of the X33 TPS test program will ilso be simulated. In this manner, the differences between the ground test simulation and the flight environment can be identified for a measure of ground test to flight traceability.

Loomis, Mark↗