Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic force microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Characterization of Al–Al{sub 4}C{sub 3} nanocomposites produced by mechanical milling

In this work, a mixture of Al–C–Al{sub 4}C{sub 3} nanopowder previously synthesized by mechanical milling and subsequent thermal treatment was used to reinforce the Al matrix. The nanocomposites were fabricated via high-energy ball milling and subsequent sintering process for different periods of time at 550 °C. Hardness and compression tests were performed to evaluate the mechanical properties of the nanocomposites in the as-milled and sintered conditions. According to the results the reinforcement located in the grain boundaries is responsible for the brittle behavior observed in the nanocomposites during the compression test. The combined effect of sintering and precipitation mechanisms produced an evident increase of the strength of the Al matrix at a relatively short sintering time. By using the Rietveld method the crystallite size and microstrain measurements were determined and correlated with the microhardness values. For the proper characterization of the nanoparticles present in the Al matrix, atomic force microscopy and high resolution electron microscopy were used. - Highlights: • Nanostructured Al{sub 4}C{sub 3} reinforcement was fabricated via mechanical milling and heat treatment. • We found a significant increase of the mechanical properties at short sintering times. • The formation of Al{sub 4}C{sub 3} with during sintering time restricted the excessive growth of the crystallite. • Al{sub 4}C{sub 3} located in the grain boundaries causes brittle fracture observed in compression tests. • There is a correlation between, crystallite size and microstrain values with microhardness.

36 MATERIALS SCIENCE↗

Effect of ammonia plasma treatment on graphene oxide LB monolayers

Graphene oxide monolayer sheets were transferred on Si and SiO{sub 2}/Si substrates by Langmuir-Blodgett technique and were exposed to ammonia plasma at room temperature. The monolayer character of both graphene oxide and plasma treated graphene oxide sheets were ascertained by atomic force microscopy. X-ray photoelectron spectroscopy and Raman spectroscopy revealed that ammonia plasma treatment results in enhancement of graphitic carbon content along with the incorporation of nitrogen. The conductivity of graphene oxide monolayers, which was in the range of 10{sup -6}-10{sup -7} S/cm, increased to 10{sup -2}-10{sup -3} S/cm after the ammonia plasma treatment. These results indicate that the graphene oxide was simultaneously reduced and N-doped during ammonia plasma treatment, without affecting the morphological stability of sheets.

36 MATERIALS SCIENCE↗

Strain relaxation in graphene grown by chemical vapor deposition

The growth of single layer graphene by chemical vapor deposition on polycrystalline Cu substrates induces large internal biaxial compressive strain due to thermal expansion mismatch. Raman backscattering spectroscopy and atomic force microscopy were used to study the strain relaxation during and after the transfer process from Cu foil to SiO{sub 2}. Interestingly, the growth of graphene results in a pronounced ripple structure on the Cu substrate that is indicative of strain relaxation of about 0.76% during the cooling from the growth temperature. Removing graphene from the Cu substrates and transferring it to SiO{sub 2} results in a shift of the 2D phonon line by 27 cm{sup −1} to lower frequencies. This translates into additional strain relaxation. The influence of the processing steps, used etching solution and solvents on strain, is investigated.

36 MATERIALS SCIENCE↗

Tuning the thickness of electrochemically grafted layers in large area molecular junctions

We have investigated the thickness, the surface roughness, and the transport properties of oligo(1-(2-bisthienyl)benzene) (BTB) thin films grafted on evaporated Au electrodes, thanks to a diazonium-based electro-reduction process. The thickness of the organic film is tuned by varying the number of electrochemical cycles during the growth process. Atomic force microscopy measurements reveal the evolution of the thickness in the range of 2–27 nm. Its variation displays a linear dependence with the number of cycles followed by a saturation attributed to the insulating behavior of the organic films. Both ultrathin (2 nm) and thin (12 and 27 nm) large area BTB-based junctions have then been fabricated using standard CMOS processes and finally electrically characterized. The electronic responses are fully consistent with a tunneling barrier in case of ultrathin BTB film whereas a pronounced rectifying behavior is reported for thicker molecular films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

AFM investigation of effect of absorbed water layer structure on growth mechanism of octadecyltrichlorosilane self-assembled monolayer on oxidized silicon

The growth mechanism of an octadecyltrichlorosilane (OTS) self-assembled monolayer on a silicon oxide surface at various relative humidities has been investigated. Atomic force microscopy images show that excess water may actually hinder the nucleation and growth of OTS islands. A moderate amount of water is favorable for the nucleation and growth of OTS islands in the initial stage; however, the completion of the monolayer is very slow in the final stage. The growth of OTS islands on a low-water-content surface maintains a relatively constant speed and requires the least amount of time. The mobility of water molecules is thought to play an important role in the OTS monolayers, and a low-mobility water layer provides a steady condition for OTS monolayer growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pulsed laser deposition films from a Ba 2 FeMoO 6 target onto SrTiO 3 [001]: Chemical and magnetic inhomogeneity

Pulsed laser deposition films from Ba 2 FeMoO 6 (BFMO) targets onto SrTiO 3 [001] (STO) substrates have been reported previously to have non-zero magnetism at 300 K, a majority of magnetic ordering at 240 K that is less than the 370 K ordering temperature of polycrystalline BFMO, and suppressed saturation magnetization compared to polycrystalline BFMO. To interrogate these previously reported observations of BFMO on STO, here we have used a combination of x-ray diffraction, atomic force microscopy, x-ray and neutron reflectivity, and x-ray photoelectron spectroscopy that shows inhomogeneities. The present results show off-stoichiometry on the A-site by incorporation of Sr from the substrate and on the B-site to have %Fe/%Mo > 1 by evolution of BaMoO 4 . There is an enhanced ordering temperature and magnetic response nearer to the SrTiO 3 interface compared to the air interface. Depth dependent strain and microstructure are needed to explain the magnetic response. Finally, holistic considerations and implications are also discussed.

36 MATERIALS SCIENCE↗

Polythiophene-block-polyfluorene and Polythiophene-blockpoly(fluorene-co-benzothiadiazole): Insights into the Self-Assembly of All-Conjugated Block Copolymers

All-conjugated block copolymers have significant potential for solution-processed optoelectronic applications, in particular those relying on a p/n junction. Herein, we report the synthesis and structure of all-conjugated diblock copolymers poly(3-hexylthiophene)-block-poly(9,9-dioctylfluorene) and poly(3-hexylthiophene)-block-poly(9,9-dioctylfluorene-co-benzothiadiazole) in thin films and in the bulk. The diblock copolymers are prepared using a combination of Grignard metathesis polymerization and Suzuki polycondensation and characterized with NMR spectroscopy, size-exclusion chromatography, multiangle laser light scattering, and UV/vis spectroscopy. Structure in thin films and in the bulk is characterized using differential scanning calorimetry, X-ray diffraction, small-angle X-ray scattering, and atomic force microscopy. Diblock copolymer thin films self-assemble into a crystalline nanostructure with some long-range order after extended solvent annealing, and X-ray scattering measurements show that powder samples exhibit crystallinity throughout the bulk. By temperature dependent X-ray scattering measurements, we find that diblock copolymers self-assemble into crystalline nanowires with phase segregated block copolymer domains. These measurements show all-conjugated diblock copolymers may be useful for achieving solution-processed active layers in organic photovoltaics and light-emitting diodes with optimized structural and photophysical characteristics.

36 MATERIALS SCIENCE↗

Substrate orientation effects on the nucleation and growth of the M{sub n+1}AX{sub n} phase Ti{sub 2}AlC

The M{sub n+1}AX{sub n} (MAX) phases are ternary compounds comprising alternating layers of a transition metal carbide or nitride and a third ''A-group'' element. The effect of substrate orientation on the growth of Ti{sub 2}AlC MAX phase films was investigated by studying pulsed cathodic arc deposited samples grown on sapphire cut along the (0001), (1010), and (1102) crystallographic planes. Characterization of these samples was by x-ray diffraction, atomic force microscopy, and cross-sectional transmission electron microscopy. On the (1010) substrate, tilted (1018) growth of Ti{sub 2}AlC was found, such that the TiC octahedra of the MAX phase structure have the same orientation as a spontaneously formed epitaxial TiC sublayer, preserving the typical TiC-Ti{sub 2}AlC epitaxial relationship and confirming the importance of this relationship in determining MAX phase film orientation. An additional component of Ti{sub 2}AlC with tilted fiber texture was observed in this sample; tilted fiber texture, or axiotaxy, has not previously been seen in MAX phase films.

36 MATERIALS SCIENCE↗

Electronic properties of ultrananocrystalline diamond surfaces.

We have characterized ultrananocrystalline diamond films with different surface terminations by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). The surface terminations were performed by plasma functionalization in atmospheres of hydrogen, fluorine, and oxygen. XPS proves the dense monolayer coverage of the surface functionalization. AFM and STM show low impact of the plasma treatment on the surface morphology. STS has been used to investigate the surface electronic properties, for H-terminated surfaces the electronic structure is dominated by the sp{sup 3} carbon phase of the grain surfaces; for O- and F-terminated surfaces, however, sp{sup 2} carbon from the grain boundaries seems to determine the surface band gap.

08 HYDROGEN↗

Microscale wear behavior and crosslinking of PEG-like coatings for total hip replacements

The predominant cause of late-state failure of total hip replacements is wear-mediated osteolysis caused by wear particles that originate from the ultrahigh molecular weight polyethylene (UHMWPE) acetabular cup surface. One strategy for reducing wear particle formation from UHMWPE is to modify the surface with a hydrophilic coating to increase lubrication from synovial fluid. This study focuses on the wear behavior of hydrophilic coatings similar to poly(ethylene glycol) (PEG). The coatings were produced by plasma-polymerizing tetraglyme on UHMWPE in a chamber heated to 40C or 50C. Both temperatures yielded coatings with PEG-like chemistry and increased hydrophilicity relative to uncoated UHMWPE; however, the 40C coatings were significantly more resistant to damage induced by atomic force microscopy nanoscratching. The 40C coatings exhibited only one damage mode (delamination) and often showed no signs of damage after repeated scratching. In contrast, the 50C coatings exhibited three damage modes (roughening, thinning, and delamination), and always showed visible signs of damage after no more than two scratches. The greater wear resistance of the 40C coatings could not be explained by coating chemistry or hydrophilicity, but it corresponded to an approximately 26–32% greater degree of crosslinking relative to the 50C surfaces, suggesting that crosslinking should be a significant design consideration for hydrophilic coatings used for total hip replacements and other wear-dependent applications.

36 MATERIALS SCIENCE↗

Intercalation leads to inverse layer dependence of friction on chemically doped MoS 2

Here, we present results of atomic-force-microscopy-based friction measurements on Re-doped molybdenum disulfide (MoS 2 ). In stark contrast to the widespread observation of decreasing friction with increasing number of layers on two-dimensional (2D) materials, friction on Re-doped MoS 2 exhibits an anomalous, i.e. inverse, dependence on the number of layers. Raman spectroscopy measurements combined with ab initio calculations reveal signatures of Re intercalation. Calculations suggest an increase in out-of-plane stiffness that inversely correlates with the number of layers as the physical mechanism behind this remarkable observation, revealing a distinctive regime of puckering for 2D materials.

42 ENGINEERING↗

Laser-Induced Modification of the Surface of Ge{sub 2}Sb{sub 2}Te{sub 5} Thin Films: Phase Changes and Periodic-Structure Formation

Submicron periodic lattices are formed at the surface of phase-change-memory film materials based on the complex chalcogenide Ge{sub 2}Sb{sub 2}Te{sub 5} when exposed to nanosecond laser pulses. The geometric characteristics and structural properties of laser-induced lattices are studied by optical and atomic-force microscopies and Raman spectroscopy. It is shown that, at appropriately chosen parameters of exposure to laser radiation, it is possible to implement periodic modulation of the refractive index in the structures formed. Modulation is due to the postexposure solidification of grating ridges and valleys in different phase states, whose dielectric constants widely differ from each other. In the vicinity of the maxima of the wavy structure, the amorphous state is mainly formed, whereas in the region of minima, the Ge{sub 2}Sb{sub 2}Te{sub 5} structure corresponds mainly to the crystalline phase.

36 MATERIALS SCIENCE↗

Inhibition of Amyloid β-Induced Lipid Membrane Permeation and Amyloid β Aggregation by K162

Alzheimer's disease (AD) is characterized by progressive neurodegeneration associated with amyloid β (Aβ) peptide aggregation. The aggregation of Aβ monomers (AβMs) leads to the formation of Aβ oligomers (AβOs), the neurotoxic Aβ form, capable of permeating the cell membrane. Here, we investigated the effect of a fluorene-based active drug candidate, named K162, on both Aβ aggregation and AβO toxicity toward the bilayer lipid membrane (BLM). Electrochemical impedance spectroscopy (EIS), atomic force microscopy (AFM), and molecular dynamics (MD) were employed to show that K162 inhibits AβOs-induced BLM permeation, thus preserving BLM integrity. In the presence of K162, only shallow defects on the BLM surface were formed. Apparently, K162 modifies Aβ aggregation by bypassing the formation of toxic AβOs, and only nontoxic AβMs, dimers (AβDs), and fibrils (AβFs) are produced. Unlike other Aβ toxicity inhibitors, K162 preserves neurologically beneficial AβMs. This unique K162 inhibition mechanism provides an alternative AD therapeutic strategy that could be explored in the future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local solid phase growth of few-layer graphene on silicon carbide from nickel silicide supersaturated with carbon

Patterned few-layer graphene (FLG) films were obtained by local solid phase growth from nickel silicide supersaturated with carbon, following a fabrication scheme, which allows the formation of self-aligned ohmic contacts on FLG and is compatible with conventional SiC device processing methods. The process was realised by the deposition and patterning of thin Ni films on semi-insulating 6H-SiC wafers followed by annealing and the selective removal of the resulting nickel silicide by wet chemistry. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to confirm both the formation and subsequent removal of nickel silicide. The impact of process parameters such as the thickness of the initial Ni layer, annealing temperature, and cooling rates on the FLG films was assessed by Raman spectroscopy, XPS, and atomic force microscopy. The thickness of the final FLG film estimated from the Raman spectra varied from 1 to 4 monolayers for initial Ni layers between 3 and 20 nm thick. Self-aligned contacts were formed on these patterned films by contact photolithography and wet etching of nickel silicide, which enabled the fabrication of test structures to measure the carrier concentration and mobility in the FLG films. A simple model of diffusion-driven solid phase chemical reaction was used to explain formation of the FLG film at the interface between nickel silicide and silicon carbide.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis and characterization of electron doped La{sub 0.85}Te{sub 0.15}MnO{sub 3} thin film grown on LaAlO{sub 3} substrate by pulsed laser deposition technique

We report the structural, morphological and magneto-transport properties of electron doped La{sub 0.85}Te{sub 0.15}MnO{sub 3} (LTMO) thin film grown on (001) LaAlO{sub 3} single crystal substrate by pulsed laser deposition (PLD). X-ray diffraction (XRD) results confirm that the film has good crystalline quality, single phase, and c-axis orientation. The atomic force microscopy (AFM) results have revealed that the film consists of grains with the average size in a range of 20–30 nm and root-mean square (rms) roughness of 0.27nm. The resistivity versus temperature measurement exhibits an insulator to metal transition (MIT). We have noticed a huge value of magnetoresistance (∼93%) close to MIT in presence of 8T field. X-ray photoemission spectroscopy confirms the electron doping and suggests that Te ions could be in the Te{sup 4+} state, while the Mn ions stay in the Mn{sup 2+} and Mn{sup 3+} valence state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reactive magnetron cosputtering of hard and conductive ternary nitride thin films: Ti-Zr-N and Ti-Ta-N

Ternary transition metal nitride thin films, with thickness up to 300 nm, were deposited by dc reactive magnetron cosputtering in Ar-N{sub 2} plasma discharges at 300 deg. C on Si substrates. Two systems were comparatively studied, Ti-Zr-N and Ti-Ta-N, as representative of isostructural and nonisostructural prototypes, with the aim of characterizing their structural, mechanical, and electrical properties. While phase-separated TiN-ZrN and TiN-TaN are the bulk equilibrium states, Ti{sub 1-x}Zr{sub x}N and Ti{sub 1-y}Ta{sub y}N solid solutions with the Na-Cl (B1-type) structure could be stabilized in a large compositional range (up to x=1 and y=0.75, respectively). Substituting Ti atoms by either Zr or Ta atoms led to significant changes in film texture, microstructure, grain size, and surface morphology, as evidenced by x-ray diffraction, x-ray reflectivity, and scanning electron and atomic force microscopies. The ternary Ti{sub 1-y}Ta{sub y}N films exhibited superior mechanical properties to Ti{sub 1-x}Zr{sub x}N films as well as binary compounds, with hardness as high as 42 GPa for y=0.69. All films were metallic, the lowest electrical resistivity {rho}{approx}65 {mu}{Omega} cm being obtained for pure ZrN, while for Ti{sub 1-y}Ta{sub y}N films a minimum was observed at y{approx}0.3. The evolution of the different film properties is discussed based on microstructrural investigations.

36 MATERIALS SCIENCE↗

Effect of Ascorbic Acid Additions on the Mechanism Underlying the Growth of Nanostructured PbSe Films via Hydrochemical Deposition

The effect of ascorbic acid additions on the growth mechanism of thin PbSe films produced by hydrochemical deposition has been studied by atomic force microscopy (AFM). A fractal analysis of AFM images of the lead selenide films has shown that their formation follows the “cluster–particle” aggregation mechanism. The fractal dimension assessed by the box-counting method is 2.26 at an average grain size of ~150 nm. From the transmission spectra of the films grown at deposition times from 20 to 120 min, we have evaluated their optical band gap, which has been shown to decrease from 0.595 to 0.53 eV with increasing deposition time. These values are attributable to the manifestation of quantum size effects in the grown PbSe films.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

PVA Based Ternary Nanocomposites with Enhanced Properties Prepared by Using a Combination of Rice Starch Nanocrystals and Silver Nanoparticles

Ternary nanocomposite films exhibiting better properties were prepared by incorporating two different nanoparticles such as rice starch nanocrystals (RSN) and silver nanoparticles (AgNPs) together in polyvinyl alcohol (PVA) matrix at various concentrations. The morphological evaluation using atomic force microscopy revealed that the particle size of RSN nanoparticles varied from 50 to 125 nm. The nanocomposite films made using these nanoparticles were evaluated for its chemical, mechanical and thermal properties. FTIR spectra of the films revealed some specific vibrational bands of RSN along with the characteristic bands of PVA. The mechanical property analysis of nanocomposite films indicated better tensile strength and elongation properties, which can be attributed to the strong interaction of PVA with RSN and AgNPs. The thermal properties of these films were also evaluated. These ternary nanocomposites exhibited superior mechanical properties, which is very much beneficial as far as the end use applications are concerned.

77 NANOSCIENCE AND NANOTECHNOLOGY↗