Search NASA⌕ Search

SEARCH · Search NASA

Results for “level sensor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Strain Gage Measurement System to Determine Cryogenic Propellant Tank Level

Measurement of tank level, particularly for cryogenic propellants, has proven to be a difficult proposition. Current methods based on differential pressure, capacitance sensors, temperature sensors, etc.; do not provide sufficiently accurate or robust measurements, especially at run time. This paper describes a simple, but effective method to determine propellant volume by measuring very small deformations of the structure supporting the tank. Results of a laboratory study to validate the method, and experimental data from a deployed system are presented. A comparison with an existing differential pressure sensor shows that the strain gage system provides a very good quality signal even during pressurization.

Figueroa, Fernando↗
NASA NTRS2006

NASA/SDSU Geopositional Characterization

The geolocational accuracy of products from the IKONOS, QuickBird, and OrbView-3 sensors was evaluated using two test sites: one developed in and around Brookings, SD, and one near Stennis Space Center, MS. Both of these relatively flat sites host over 100 ground control points surveyed to an accuracy of approximately 5 cm. They provide robust locations to test the basic geolocational accuracy of a variety of spaceborne and aircraft sensor systems. Imagery of both test sites was acquired by these three sensors in 2004 and in 2005; several products from each sensor, ranging from basic datasets through orthorectified imagery, were analyzed at Stennis Space Center and at South Dakota State University. While direct comparisons between sensors and products are difficult because of differing processing schemes, results indicate that these products tend to display stated levels of accuracy.

Helder, Dennis↗
NASA NTRS2006

Building Complex Systems

The explosion of capabilities and new products within ICT (Information and Communication Technology) has fostered widespread, overly optimistic opinions regarding the industry, based on common but unjustified assumptions of quality and correctness of software. These assumptions are encouraged by software producers and vendors, who have not succeeded in finding a way to overcome the lack of an automated, mathematically sound way to develop correct systems from requirements. NASA faces this dilemma as it envisages advanced mission concepts in future exploration missions, which may well be the most ambitious computer-based systems ever developed. Such missions entail levels of complexity that beg for new methods for system development. NASA-led research in such areas as sensor networks, formal methods, autonomic computing, and requirements-based programming (to name but a few) will offer some innovative approaches to achieving correctness in complex system development.

Hinchey, Mike↗
NASA NTRS2009

Modular Battery Charge Controller

A new approach to masterless, distributed, digital-charge control for batteries requiring charge control has been developed and implemented. This approach is required in battery chemistries that need cell-level charge control for safety and is characterized by the use of one controller per cell, resulting in redundant sensors for critical components, such as voltage, temperature, and current. The charge controllers in a given battery interact in a masterless fashion for the purpose of cell balancing, charge control, and state-of-charge estimation. This makes the battery system invariably fault-tolerant. The solution to the single-fault failure, due to the use of a single charge controller (CC), was solved by implementing one CC per cell and linking them via an isolated communication bus [e.g., controller area network (CAN)] in a masterless fashion so that the failure of one or more CCs will not impact the remaining functional CCs. Each micro-controller-based CC digitizes the cell voltage (V(sub cell)), two cell temperatures, and the voltage across the switch (V); the latter variable is used in conjunction with V(sub cell) to estimate the bypass current for a given bypass resistor. Furthermore, CC1 digitizes the battery current (I1) and battery voltage (V(sub batt) and CC5 digitizes a second battery current (I2). As a result, redundant readings are taken for temperature, battery current, and battery voltage through the summation of the individual cell voltages given that each CC knows the voltage of the other cells. For the purpose of cell balancing, each CC periodically and independently transmits its cell voltage and stores the received cell voltage of the other cells in an array. The position in the array depends on the identifier (ID) of the transmitting CC. After eight cell voltage receptions, the array is checked to see if one or more cells did not transmit. If one or more transmissions are missing, the missing cell(s) is (are) eliminated from cell-balancing calculations. The cell-balancing algorithm is based on the error between the cell s voltage and the other cells and is categorized into four zones of operation. The algorithm is executed every second and, if cell balancing is activated, the error variable is set to a negative low value. The largest error between the cell and the other cells is found and the zone of operation determined. If the error is zero or negative, then the cell is at the lowest voltage and no balancing action is needed. If the error is less than a predetermined negative value, a Cell Bad Flag is set. If the error is positive, then cell balancing is needed, but a hysteretic zone is added to prevent the bypass circuit from triggering repeatedly near zero error. This approach keeps the cells within a predetermined voltage range.

Button, Robert↗
NASA NTRS2010

The Goes-R Geostationary Lightning Mapper (GLM): Algorithm and Instrument Status

The Geostationary Operational Environmental Satellite (GOES-R) is the next series to follow the existing GOES system currently operating over the Western Hemisphere. Superior spacecraft and instrument technology will support expanded detection of environmental phenomena, resulting in more timely and accurate forecasts and warnings. Advancements over current GOES capabilities include a new capability for total lightning detection (cloud and cloud-to-ground flashes) from the Geostationary Lightning Mapper (GLM), and improved capability for the Advanced Baseline Imager (ABI). The Geostationary Lighting Mapper (GLM) will map total lightning activity (in-cloud and cloud-to-ground lighting flashes) continuously day and night with near-uniform spatial resolution of 8 km with a product refresh rate of less than 20 sec over the Americas and adjacent oceanic regions. This will aid in forecasting severe storms and tornado activity, and convective weather impacts on aviation safety and efficiency. In parallel with the instrument development (a prototype and 4 flight models), a GOES-R Risk Reduction Team and Algorithm Working Group Lightning Applications Team have begun to develop the Level 2 algorithms, cal/val performance monitoring tools, and new applications. Proxy total lightning data from the NASA Lightning Imaging Sensor on the Tropical Rainfall Measuring Mission (TRMM) satellite and regional test beds are being used to develop the pre-launch algorithms and applications, and also improve our knowledge of thunderstorm initiation and evolution. A joint field campaign with Brazilian researchers in 2010-2011 will produce concurrent observations from a VHF lightning mapping array, Meteosat multi-band imagery, Tropical Rainfall Measuring Mission (TRMM) Lightning Imaging Sensor (LIS) overpasses, and related ground and in-situ lightning and meteorological measurements in the vicinity of Sao Paulo. These data will provide a new comprehensive proxy data set for algorithm and application development.

Goodman, Steven J.↗
NASA NTRS2011

The GOES-R Series Geostationary Lightning Mapper (GLM)

The Geostationary Operational Environmental Satellite (GOES-R) is the next series to follow the existing GOES system currently operating over the Western Hemisphere. Superior spacecraft and instrument technology will support expanded detection of environmental phenomena, resulting in more timely and accurate forecasts and warnings. Advancements over current GOES capabilities include a new capability for total lightning detection (cloud and cloud-to-ground flashes) from the Geostationary Lightning Mapper (GLM), which will have just completed Critical Design Review and move forward into the construction phase of instrument development. The GLM will operate continuously day and night with near-uniform spatial resolution of 8 km with a product refresh rate of less than 20 sec over the Americas and adjacent oceanic regions. This will aid in forecasting severe storms and tornado activity, and convective weather impacts on aviation safety and efficiency. In parallel with the instrument development (an engineering development unit and 4 flight models), a GOES-R Risk Reduction Team and Algorithm Working Group Lightning Applications Team have begun to develop the Level 2 algorithms, cal/val performance monitoring tools, and new applications. Proxy total lightning data from the NASA Lightning Imaging Sensor (LIS) on the Tropical Rainfall Measuring Mission (TRMM) satellite and regional ground-based lightning networks are being used to develop the pre-launch algorithms, test data sets, and applications, as well as improve our knowledge of thunderstorm initiation and evolution. In this presentation we review the planned implementation of the instrument and suite of operational algorithms

Goodman, Steven J.↗
NASA NTRS2011

The Goes-R Geostationary Lightning Mapper (GLM)

The Geostationary Operational Environmental Satellite (GOES-R) is the next series to follow the existing GOES system currently operating over the Western Hemisphere. Superior spacecraft and instrument technology will support expanded detection of environmental phenomena, resulting in more timely and accurate forecasts and warnings. Advancements over current GOES capabilities include a new capability for total lightning detection (cloud and cloud-to-ground flashes) from the Geostationary Lightning Mapper (GLM), and improved storm diagnostic capability with the Advanced Baseline Imager. The GLM will map total lightning activity (in-cloud and cloud-to-ground lighting flashes) continuously day and night with near-uniform spatial resolution of 8 km with a product refresh rate of less than 20 sec over the Americas and adjacent oceanic regions. This will aid in forecasting severe storms and tornado activity, and convective weather impacts on aviation safety and efficiency. In parallel with the instrument development, a GOES-R Risk Reduction Team and Algorithm Working Group Lightning Applications Team have begun to develop the Level 2 algorithms, cal/val performance monitoring tools, and new applications. Proxy total lightning data from the NASA Lightning Imaging Sensor on the Tropical Rainfall Measuring Mission (TRMM) satellite and regional test beds are being used to develop the pre-launch algorithms and applications, and also improve our knowledge of thunderstorm initiation and evolution. In this paper we will report on new Nowcasting and storm warning applications being developed and evaluated at various NOAA Testbeds.

Goodman, Steven J.↗
NASA NTRS2012

Alumina Based 500 C Electronic Packaging Systems and Future Development

NASA space and aeronautical missions for probing the inner solar planets as well as for in situ monitoring and control of next-generation aeronautical engines require high-temperature environment operable sensors and electronics. A 96% aluminum oxide and Au thick-film metallization based packaging system including chip-level packages, printed circuit board, and edge-connector is in development for high temperature SiC electronics. An electronic packaging system based on this material system was successfully tested and demonstrated with SiC electronics at 500 C for over 10,000 hours in laboratory conditions previously. In addition to the tests in laboratory environments, this packaging system has more recently been tested with a SiC junction field effect transistor (JFET) on low earth orbit through the NASA Materials on the International Space Station Experiment 7 (MISSE7). A SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE7 suite to International Space Station via a Shuttle mission and tested on the orbit for eighteen months. A summary of results of tests in both laboratory and space environments will be presented. The future development of alumina based high temperature packaging using co-fired material systems for improved performance at high temperature and more feasible mass production will also be discussed.

Chen, Liang-Yu↗
NASA NTRS2012

Modular Integrated Stackable Layers (MISL) 1.1 Design Specification

This document establishes the design guideline of the Modular Instrumentation Data Acquisition (MI‐DAQ) system in utilization of several designs available in EV. The MI‐ DAQ provides the options to the customers depending on their system requirements i.e. a 28V interface power supply, a low power battery operated system, a low power microcontroller, a higher performance microcontroller, a USB interface, a Ethernet interface, a wireless communication, various sensor interfaces, etc. Depending on customer's requirements, the each functional board can be stacked up from a bottom level of power supply to a higher level of stack to provide user interfaces. The stack up of boards are accomplished by a predefined and standardized power bus and data bus connections which are included in this document along with other physical and electrical guidelines. This guideline also provides information for a new design options. This specification is the product of a collaboration between NASA/JSC/EV and Texas A&M University. The goal of the collaboration is to open source the specification and allow outside entities to design, build, and market modules that are compatible with the specification. NASA has designed and is using numerous modules that are compatible to this specification. A limited number of these modules will also be released as open source designs to support the collaboration. The released designs are listed in the Applicable Documents.

Yim, Hester J.↗
NASA NTRS2018

A Case Study Comparing Citizen Science Aurora Data with Global Auroral Boundaries Derived from Satellite Imagery and Empirical Models

Aurorasaurus is a citizen science project that offers a new, global data source consisting of ground-based reports of the aurora. For this case study, aurora data collected during the 17-18 March 2015 geomagnetic storm are examined to identify their conjunctions with Defense Meteorological Satellite Program (DMSP) satellite passes over the high latitude auroral regions. This unique set of aurora data can provide ground-truth validation of existing auroral precipitation models. Particularly, the solar wind driven, Oval Variation, Assessment, Tracking, Intensity, and Online Nowcasting (OVATION) Prime 2013 (OP-13) model and a Kp-dependent model of Zhang-Paxton (Z-P) are utilized for our boundary validation efforts. These two similar models are compared for the first time. Global equatorward auroral boundaries are derived from the OP 13 model and the DMSP Special Sensor Ultraviolet Spectrographic Imager (SSUSI) far ultraviolet (FUV) data using the Z-P model at a fixed flux level of 0.2 erg cm(exp -2)s(exp -1). These boundaries are then compared with citizen science reports as well as with each other. Even though there are some large differences between the global boundaries for a few cases, the average difference is about 1.5 deg in geomagnetic latitude, with OP-13 being equatorward of Z-P model. When these boundaries are compared with each other as a function of local time, no clear overall trend as a function of local time was observed. It is also found that the ground based reports are more consistent with the predictions of the OP-13 model.

Kosar, Burcu C.↗
NASA NTRSDate not supplied

PACE OCI Polarization Sensitivity Based on Pre-launch Testing

The Ocean Color Instrument (OCI) is a sensor on the upcoming Plankton, Aerosol, Cloud, ocean Ecosystem (PACE) mission, scheduled for launch in early 2024. OCI is a grating spectrometer with hyperspectral coverage from the ultraviolet (about 310 nm) to near-infrared (about 900 nm), with additional filtered channels in the short-wave infrared (940 nm – 2260 nm). This instrument will provide ocean color science data to continue the data sets collected by heritage sensors MODIS, SeaWiFs, and VIIRS, but with increased spectral coverage and improved accuracy. In order to achieve the high levels of accuracy demanded by the science community, a rigorous ground test program was conducted to calibrate the instrument and ensure that the calibration can be transferred to on-orbit operations. Some calibration parameters can only be measured during pre-launch testing; one such parameter is the polarization sensitivity. Polarization testing measured the Mueller matrix components needed to determine the polarization sensitivity for all spectral bands for a series of telescope scan angles covering the expected on-orbit scan range. Results indicate that the sensitivity is below 0.6 % except at the shortest wavelengths (less than 340 nm) and was characterized to better than 0.1 % above 340 nm. This indicates that any polarized scenes measured on orbit can be corrected for with a high degree of confidence.

PACE↗
NASA NTRSDate not supplied

PACE OCI Polarization Sensitivity Based on Pre-launch Testing

The Ocean Color Instrument (OCI) is a sensor on the upcoming Plankton, Aerosol, Cloud, ocean Ecosystem (PACE) mission, scheduled for launch in early 2024. OCI is a grating spectrometer with hyperspectral coverage from the ultraviolet (about 310 nm) to near-infrared (about 900 nm), with additional filtered channels in the short-wave infrared (940 nm – 2260 nm). This instrument will provide ocean color science data to continue the data sets collected by heritage sensors MODIS, SeaWiFs, and VIIRS, but with increased spectral coverage and improved accuracy. In order to achieve the high levels of accuracy demanded by the science community, a rigorous ground test program was conducted to calibrate the instrument and ensure that the calibration can be transferred to on-orbit operations. Some calibration parameters can only be measured during pre-launch testing; one such parameter is the polarization sensitivity. Polarization testing measured the Mueller matrix components needed to determine the polarization sensitivity for all spectral bands for a series of telescope scan angles covering the expected on-orbit scan range. Results indicate that the sensitivity is below 0.6 % except at the shortest wavelengths (less than 340 nm) and was characterized to better than 0.1 % above 340 nm. This indicates that any polarized scenes measured on orbit can be corrected for with a high degree of confidence.

PACE↗
DOE OSTI2020

The CMS Outer Tracker for the High Luminosity LHC

The High Luminosity LHC (HL-LHC) is expected to deliver an integrated luminosity of 3000 - 4000 fb -1 in its lifetime with peak instantaneous luminosities reaching about 5 - 7.5×10 34 cm -2 s -1 . During the Long Shutdown 3 period, several components of the CMS detector will undergo major changes, called Phase-2 upgrades, to be able to operate in the challenging environment of the HL-LHC, including the replacement of the entire silicon tracker. The Phase-2 Outer Tracker (OT) will have high radiation tolerance, higher granularity, and the capability to handle higher data rates. Another key feature of the OT will be to provide tracking information to the Level-1 trigger, allowing trigger rates to be kept at a sustainable level without sacrificing physics potential. For this, the OT will be made of modules that have two closely spaced sensors read out by the same electronics, which can correlate hits in the two sensors creating short track segments called ”stubs”. The stubs will be used for tracking at 40 MHz. In this contribution, the design of the CMS Phase-2 OT, the technological choices, and highlights of research and development activities are reported.

Ravera, Fabio↗
NASA NTRS2010

Spectral Indices to Monitor Nitrogen-Driven Carbon Uptake in Field Corn

Climate change is heavily impacted by changing vegetation cover and productivity with large scale monitoring of vegetation only possible with remote sensing techniques. The goal of this effort was to evaluate existing reflectance (R) spectroscopic methods for determining vegetation parameters related to photosynthetic function and carbon (C) dynamics in plants. Since nitrogen (N) is a key constituent of photosynthetic pigments and C fixing enzymes, biological C sequestration is regulated in part by N availability. Spectral R information was obtained from field corn grown at four N application rates (0, 70, 140, 280 kg N/ha). A hierarchy of spectral observations were obtained: leaf and canopy with a spectral radiometer; aircraft with the AISA sensor; and satellite with EO-1 Hyperion. A number of spectral R indices were calculated from these hyperspectral observations and compared to geo-located biophysical measures of plant growth and physiological condition. Top performing indices included the R derivative index D730/D705 and the normalized difference of R750 vs. R705 (ND705), both of which differentiated three of the four N fertilization rates at multiple observation levels and yielded high correlations to these carbon parameters: light use efficiency (LUE); C:N ratio; and crop grain yield. These results advocate the use of hyperspectral sensors for remotely monitoring carbon cycle dynamics in managed terrestrial ecosystems.

Corp, Lawrence A.↗
NASA NTRS2019

Initial Trade Study for In-line Silver Sensor for Spacecraft Potable Water Systems

Ionic silver is currently baselined as the biocide for microbial control in potable water systems for future space exploration missions. In-line monitoring of silver ion concentration is desired for system feedback control to introduce and maintain sufficient and safe levels of biocide in the water. To date, NASA testing of silver biocide system prototypes has made use of an Ion-Selective Electrode (ISE) for in-line silver concentration measurements. However, known issues with ISE technology have continued to motivate a search for alternate sensor systems. Although devices capable of detecting silver are available for terrestrial applications, these systems are generally not well-suited for the unique demands of spaceflight. Desired attributes include: low weight, volume, and power consumption; stable, autonomous, and in-line measurement capability; long calibration lifetime; and limited maintenance requirements. This paper provides the results from a preliminary trade study conducted on three candidate silver sensor technologies: ISEs, Anodic Stripping Voltammetry (ASV), and Fiber Optic Chemical Sensors (FOCS). The review of these technologies includes the rationale for their selection, an overview of the principles of their operation, and a detailed assessment of their strengths and weaknesses relative to the anticipated requirements of future spacecraft applications. The study concluded that none of the currently-available versions of these technologies is suitable for immediate application to spacecraft systems; further technology development should be considered. To that end, recommendations for forward development work have been proposed and provided herein.

Potable Water↗
NASA NTRS1984

Experience with 800 x 800 virtual phase and 500 x 500 three-phase CCD imagers

A description of the Galileo/Institute for Astronomy charge-coupled device (CCD) imaging system and its initial operation has been presented previously. Originally designed to operate a 500 x 500 backside illuminated three-phase CCD, the system has been modified to allow use of either the 500 x 500 sensor or the TI 800 x 800 virtual phase CCD. The modifications for the operation of the virtual phase CCD and current system performance with each type of sensor are discussed. A description is given of the implementation of various techniques discovered at the Jet Propulsion Laboratory that improve imager performance. These techniques include tri-level clocking of the virtual phase CCD to eliminate spurious charge generation in the serial register, the use of ultraviolet light flood with the backside thinned 500 x 500 three-phase device to dramatically improve the quantum efficiency in the blue, and the practical elimination of deferred charge in the three-phase device. Results of astronomical observations with each sensor are presented.

Hlivak, R. J.↗
NASA NTRS2001

A Sensor-Independent Gust Hazard Metric

A procedure for calculating an intuitive hazard metric for gust effects on airplanes is described. The hazard metric is for use by pilots and is intended to replace subjective pilot reports (PIREPs) of the turbulence level. The hazard metric is composed of three numbers: the first describes the average airplane response to the turbulence, the second describes the positive peak airplane response to the gusts, and the third describes the negative peak airplane response to the gusts. The hazard metric is derived from any time history of vertical gust measurements and is thus independent of the sensor making the gust measurements. The metric is demonstrated for one simulated airplane encountering different types of gusts including those derived from flight data recorder measurements of actual accidents. The simulated airplane responses to the gusts compare favorably with the hazard metric.

Stewart, Eric C.↗