Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Assessment of a mechanistic model in U-Pu-Zr metallic alloy fuel fission-gas behavior simulations

A mechanistic kinetic rate theory model originally developed for the prediction of fission gas behavior in oxide nuclear fuels under steady-state and transient conditions has been assessed to look at its applicability to model fission gas behavior in U-Pu-Zr metallic alloy fuel. In order to capture and validate the underlying physics for irradiated U-Pu-Zr fuels, the mechanistic model was applied to the simulation of fission gas release, fission gas and fission product induced swelling, and the evolution of the gas bubble size distribution in three different fuel zones: the outer {alpha}-U, the intermediate, and the inner {gamma}-U zones. Due to its special microstructural features, the {alpha}-U zone in U-Pu-Zr fuels is believed to contribute the largest fraction of fission gas release among the different fuel zones. It is shown that with the use of small effective grain sizes, the mechanistic model can predict fission gas release that is consistent with (though slightly lower than) experimentally measured data. These simulation results are comparable to the experimentally measured fission gas release since the mechanism of fission gas transport through the densely distributed laminar porosity in the {alpha}-U zone is analogous to the mechanism of fission gas transport through the interconnected gas bubble porosity utilized in the mechanistic model. Detailed gas bubble size distributions predicted with the mechanistic model in both the intermediate zone and the high temperature {gamma}-U zone of U-Pu-Zr fuel are also compared to experimental measurements from available SEM micrographs. These comparisons show good agreements between the simulation results and experimental measurements, and therefore provide crucial guidelines for the selection of key physical parameters required for modeling these two zones. In addition, the results of parametric studies for several key parameters are presented for both the intermediate zone and the {gamma}-U zone simulations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fluctuating Hydrodynamics Methods for Dynamic Coarse-Grained Implicit-Solvent Simulations in LAMMPS

We present a software package integrated with the molecular dynamics software LAMMPS for fluctuating hydrodynamics simulations of fluid-structure interactions subject to thermal fluctuations. The package is motivated to provide dynamic thermostats to extend implicit-solvent coarse-grained (IS-CG) models by incorporating kinetic contributions from the solvent to facilitate their use in a wider range of applications. To capture the thermal and hydrodynamic contributions of the solvent to dynamics, we introduce momentum conserving thermostats and computational methods based on fluctuating hydrodynamics and the stochastic Eulerian Lagrangian method (SELM). SELM couples the coarse-grained microstructure degrees of freedom to continuum stochastic fields to capture both the relaxation of hydrodynamic modes and thermal fluctuations. Features of the SELM software include (i) numerical time-step integrators for SELM fluctuating hydrodynamics in inertial and quasi-steady regimes, (ii) Lees--Edwards-style methods for imposing shear, (iii) a Java-based graphical user interface (GUI) for setting up models and simulations, (iv) standardized XML formats for parametrization and data output, and (v) standardized formats VTK for continuum fields and microstructures. The SELM software package facilitates for pre-established models in LAMMPS easy adoption of the SELM fluctuating hydrodynamics thermostats. We offer here an overview of the SELM software package, computational methods, and applications.

97 MATHEMATICS AND COMPUTING↗

Five-fold twin formation during annealing of nanocrystalline Cu

Contrary to the common belief that many-fold twins, or star twins, in nanophase materials are due to the action of significant external stresses, we report molecular dynamics simulations of annealing in 5 nm grain size samples annealed at 800 K for nearly 0.5 nsec at 0 external pressure showing the formation of five-fold star twins during annealing under the action of the large internal stresses responsible for grain growth and microstructural evolution. The structure of the many-fold twins is remarkably similar to those we have found to occur under uniaxial shock loading, of samples of nanocrystalline NiW with a grain size of {approx}5-30 nm. The mechanism of formation of the many-fold twins is discussed in the light of the simulations and experiments.

36 MATERIALS SCIENCE↗

Fracture Toughness of Microstructural Gradients

Traditional singularity-based fracture mechanics theories rely on their ability to infer the crack tip driving force (local field) by surveying macroscopic physical magnitudes far from the crack tip (far field). This key capability allows engineers to employ nominal forces or displacements to estimate the potential for stable or unstable crack growth. In the case of heterogeneous or anisotropic materials, traditional fracture approaches are not fully theoretically sound and applications rely on extrapolating methodologies with ad-hoc corrections. This Express Laboratory Directed Research and Development (ELDRD) program employed mesoscale-sensitive finite element simulations to assess the impact of grain size and texture on the crack tip behavior. A dislocation-based crystal plasticity model conveys grain size effects by computing the constraint on dislocation cell structures. We assessed the effects of microstructural variability on multiple displacement-based measurements of the fracture driving forces for crack opening (Mode I) and sliding (Mode II). We also consider multiple microstructural realizations of single phase metals undergoing ductile failure. The results show that grain size and texture affect the applied fracture driving force and can induce a significant Mode II deformation under force and displacement control, which is completely neglected in homogeneous models. A large variability in driving forces upon identical far field applied conditions is attributed to a buffering effects of the microstructure. Furthermore, crack mouth opening displacement is almost insensitive to microstructure, which suggests that experimental measurements using such a magnitude (e.g., plastic hinge model) may underestimate local crack tip driving force variability.

42 ENGINEERING↗

Molecular dynamics simulations of solid state recrystallization I: Observation of grain growth in annealed iron nanoparticles

Molecular dynamics simulations of solid state recrystallization and grain growth in iron nanoparticles containing 1436 atoms were carried out. During the period of relaxation of supercooled liquid drops and during thermal annealing of the solids they froze to, changes in disorder were followed by monitoring changes in energy and the migration of grain boundaries. All 27 polycrystalline nanoparticles, which were generated with different grain boundaries, were observed to recystallize into single crystals during annealing. Larger grains consumed the smaller ones. In particular, two sets of solid particles, designated as A and B, each with two grains, were treated to generate 18 members of each set with different thermal histories. This provided small ensembles (of 18 members each) from which rates at which the larger grain engulfed the smaller one, could be determined. The rate was higher, the smaller the degree of misorientation between the grains, a result contrary to the general rule based on published experiments, but the reason was clear. Crystal A, which happened to have a somewhat lower angle of misorientation, also had a higher population of defects, as confirmed by its higher energy. Accordingly, its driving force to recrystallize was greater. Although the mechanism of recrystallization is commonly called nucleation, our results, which probe the system on an atomic scale, were not able to identify nuclei unequivocally. By contrast, our technique can and does reveal nuclei in the freezing of liquids and in transformations from one solid phase to another. An alternative rationale for a nucleation-like process in our results is proposed. - Graphical Abstract: Time dependence of energy per atom in the quenching of liquid nanoparticles A-C of iron. Nanoparticle C freezes directly into a single crystal but A and B freeze to solids with two grains. A and B eventually recrystallize into single crystals. Highlights: Black-Right-Pointing-Pointer Solid state material synthesis. Black-Right-Pointing-Pointer Experimental study of nucleation in condensed materials. Black-Right-Pointing-Pointer Computation Study of nucleation in condensed materials. Black-Right-Pointing-Pointer Observation of recrystallization in atomic detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ irradiation of spent nuclear fuels

To improve the economics of commercial nuclear reactors, nuclear vendors and utilities are seeking approval for increased burnup usage of the existing nuclear fleet. This is especially critical for meeting the clean energy initiative by the United States Government, Department of Energy (DOE). However, one of the key challenges the nuclear industry faces in this regard is that the regions exposed to high burnup and low temperatures exhibit a fine-grained microstructure with large bubbles known as high-burnup structure (HBS) [1]. The formation of HBS has been correlated to the diminished performance of the reactor, as well as fuel fragmentation and pulverization during transient and accidental conditions [2]. Therefore, it is paramount to understand the mechanisms for HBS formation along with its impact on the properties and performance of nuclear fuels. While existing programs, such as Nuclear Energy Advanced Modeling and Simulation (NEAMS) and Advanced Fuel Campaign (AFC) are focusing on evaluating the performance impact of HBS, the physical mechanisms contributing to HBS formation are still not fully understood. In addition, having predictive capabilities and sound understanding of the microstructural evolution of nuclear fuel is essential for accelerated development, qualification, and deployment of new nuclear materials and novel reactor designs for advanced nuclear reactors. There is a lack of consensus among researchers regarding the mechanisms leading to such restructuring observed in HBS. Grain subdivision due to polygonization versus recrystallization, continuous versus discrete recrystallization occurring in tandem or conjunction, etc., have been proposed and debated. In general, it is hypothesized that defect accumulation and dislocation interaction within the grains cause the realignment of dislocations into grain boundaries, leading to the new subgrain formation, which over time transforms into new grains. However, due to the lack of transient data, the importance of fission rate, irradiation, thermal, and stress history of the fuel on the restructuring could not be assessed. In situ microstructural evolution under various irradiation conditions is desired to bridge this gap. Alternatively, phase-field-based models have been developed to capture HBS formation via discrete recrystallization utilizing the classical nucleation approach [3–5]. However, in these models, the grain nucleation criteria are often defined based on empirical relations for burnup and fission gas density leading to dislocation density change. A mechanistic approach to capture the dislocation interaction with the microstructural features leading to grain subdivision is lacking.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion Performance of Fe-Based Alloys in Simulated Oxy-Fuel Environment

The long-term corrosion of Fe-based alloys in simulated oxy-fuel environment at 1023 K (750 A degrees C) was studied. Detailed results are presented on weight change, scale thickness, internal penetration, microstructural characteristics of the corrosion products, and the cracking of scales for the alloys after exposure at 1023 K (750 A degrees C) for up to 3600 hours. An incubation period during which the corrosion rate was low was observed for the alloys. After the incubation period, the corrosion accelerated, and the corrosion process followed linear kinetics. Effects of alloy, CaO-containing ash, and gas composition on the corrosion rate were also studied. In addition, synchrotron nanobeam X-ray analysis was employed to determine the phase and chemical composition of the oxide layers on the alloy surface. Results from these studies are being used to address the long-term corrosion performance of Fe-based alloys in various coal-ash combustion environments and to develop methods to mitigate high-temperature ash corrosion.

36 MATERIALS SCIENCE↗

Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy

The in-situ neutron diffraction technique, in combination with both the full-field crystal elasto-viscoplastic finite element model and microstructural characterization, was used to study the deformation-induced damage anisotropy in a commercial Al alloy, subjected to uniaxial tensile and cyclic loading. The simulations capture well the crystallographic-orientation-dependent lattice strain behavior. The hard grains, e.g. those orientated with the <111> and <422> orientations parallel with the uniaxial loading direction (LD), feature large Taylor factors and seem more prone to form damage-related band structures. Their effective elastic moduli decrease with the accumulation of damage, which are different from the soft grains orientated with the <200> orientation along the LD. Correlation between the distribution of voids and that of the residual lattice strain developed after failure may exist. The maximum tensile type residual lattice strain observed after failure may be resulted from the band structure formed in the hardest <111> grains. It was revealed that the band structure triggered by the hard particles could be one of sources of damage. In addition, while the specimen was obviously damaged, a fast stress relief was evidenced after unloading from the tension, especially at the beginning of unloading. Our present investigations provide a novel method for exploring the damage mechanisms of polycrystalline materials during plastic deformation.

36 MATERIALS SCIENCE↗

Vapor–Liquid Equilibrium and Polarization Behavior of the GCP Water Model: Gaussian Charge-on-Spring versus Dipole Self-Consistent Field Approaches to Induced Polarization

Here we implemented the Gaussian charge-on-spring (GCOS) version of the original self-consistent field implementation of the Gaussian Charge Polarizable water model and test its accuracy to represent the polarization behavior of the original model involving smeared charges and induced dipole moments. Moreover, for that purpose we adapted the recently developed multiple-particle-move (MPM) within the Gibbs and isochoric-isothermal ensembles Monte Carlo methods for the efficient simulation of polarizable fluids. We also assessed the accuracy of the GCOS representation by a direct comparison of the resulting vapor-liquid phase envelope, microstructure, and relevant microscopic descriptors of water polarization along the orthobaric curve against the corresponding quantities from the actual GCP water model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scale Invariance of Hot Spot Formation in TATB High Explosives

Shock-induced detonation of insensitive high explosives based on 1,3,5-triamino-2,4,6-trinitrobenzene starts with formation of hot spots at microstructural defects but has eluded atomistic modeling treatment at micron length scales. To this end, we performed multimicron scale all-atom molecular dynamics (MD) simulations of hot spots that form during the collapse of cylindrical pores with diameters between 10 and 300 nm. Our MD simulations show that hot spots formed at pores larger than 20 nm exhibit temperature fields with scale-invariant features for sizes up to at least 300 nm. Through a continuum-based grain-scale modeling framework, we span and extend beyond the size scales currently accessible to MD and find that hot spot scale invariance is a general feature that arises when the mechanical strength is insensitive to strain rate. Finally, our results demonstrate the applicability of all-atom MD to simulate the complicated dynamical evolution of micron-sized systems and bolster confidence in insights from MD simulations of materials that exhibit strength with negligible rate dependence over the relevant intervals.

36 MATERIALS SCIENCE↗

Direct Measurements of Ionic Transport Behavior of Dual-Layer Porous Electrodes

To improve power and cycling performance of lithium-ion batteries, dual-layer or porosity-gradient electrodes have been proposed. By engineering a higher porosity close to the separator, the intention is to improve ion transport where it is most impactful. In this research, MacMullin numbers of two dual-layer anode samples are tested using an impedance measurement technique developed previously. To characterize the microstructure of each layer independently, we developed an improved transmission-line model that accounts for each layer's properties.Virtual experiments using COMSOL Multiphysics to simulate impedance measurements are used to examine and improve the accuracy of the numerical inversion procedure. The results for the two dual-layer anodes studied show that MacMullin numbers follow expected trends, though the anodes are quite different from each other.

Dual-Layer Electrodes↗

Imaging transient solidification behavior

Solidification processing offers the first opportunity to control microstructure, properties, and performance in metallic alloy components. Until recently, microstructural evaluations were limited to post-solidification characterization by destructive methods. We review the development of time-resolved, in situimaging techniques capable of capturing solid-liquid interfacial evolution in metallic alloys with high spatial and temporal resolution underdiverse solidification conditions relevant for applications ranging from conventional directional solidification, crystal growth, and casting,to welding and additive manufacturing. These experiments enable direct visualization of transient behaviors that would otherwise remain unknown, uniquely providinginsights into the physics that impact microstructure and defect development and strategies for microstructuralcontrol and defect mitigation. Understanding microstructural evolution and the characteristics that form under various solidification conditions is essential for the development of multiscale, experimentallyinformed predictive modeling. This is highlightedby solidification simulations that utilize in situmeasurements of solidification dynamics from state-of-the-art experimental techniques.

36 MATERIALS SCIENCE↗

Investigation on laser absorption and x-ray radiation in microstructured titanium targets heated by short-pulse relativistic laser pulses

The enhancement effect of a microstructured surface on laser absorption and characteristic Kα emission has been investigated by measuring K-shell emission from titanium (Ti) targets irradiated with high-intensity (~10 20 W cm -2 ), subpicosecond (500 fs) laser pulses. The experimental results indicate a modest enhancement (1.6×) of Kα emission from microstructured targets compared to flat foils, but with a similar intensity and profile of Heα and Li-like satellites. Particle-in-cell (PIC) simulations are implemented to further understand the underlying physical processes in the laser interaction with both targets, interpreting the mechanisms responsible for the Kα enhancement. The reasons for the lower-than-expected enhancement of Kα emission are discussed. The rapid heating of the bulk plasma might result in the premature shutdown of Kα emission before the thermalization of hot electrons or even the end of laser pulses, suggesting that the use of Kα emission as a diagnostic of the hot-electron yield or relaxation could lead to a misinterpretation.

36 MATERIALS SCIENCE↗

Characterization of Fe-6Si Soft Magnetic Alloy Produced by Laser-Directed Energy Deposition Additive Manufacturing

Abstract Commercial electrical steels, Fe-Si alloys with < 4 wt.% Si, are inexpensive and efficient materials for electrical power conversion. Further efficiency improvements require increasing the silicon concentration to 6 wt.%, at which point the material becomes brittle and difficult to form by conventional rolling and sheet fabrication methods. Additive manufacturing stands to overcome challenges with commercial manufacturing techniques by leveraging near-net-shape fabrication. The wide array of process conditions provides additive manufacturing with increased flexibility, enabling control over the microstructure and mechanical properties. This work explores the microstructures and magnetic properties of ring-shaped Fe-Si alloys produced using concentric and cross-hatch tool paths on a laser-directed energy deposition additive manufacturing system. Concentric-built samples exhibit elongated grain structures while cross-hatch-built samples comprise lower aspect ratio grain structures. Thermal finite element analysis simulations model the stress conditions produced by the different scan path geometries. Microhardness measurements probe the mechanical properties as a function of anneal temperature, providing a qualitative understanding of the intergranular defect density. Soft magnetic properties measured under quasistatic and AC conditions show frequency- and microstructure-dependent coercivity and permeability. Finally, analysis of the core loss quantifies how the build strategies and thermal treatments influence efficiency in electrical power conversion applications. Understanding the influences of scan path geometry and thermal treatment provides a pathway towards application of additively manufactured soft magnetic materials.

Adamczyk, Jesse M.↗

Uncertainty quantification for competing failure mechanisms in unidirectionally reinforced carbon–carbon composites

Microstructure-informed finite element models play a key role in the carbon–carbon composite design process. Variability in manufacturing process parameters and experimental limitations introduce model parameter uncertainty. This study quantifies the effect of model parameter uncertainty on transverse tensile fracture behavior and proposes a methodology to predict the failure mode based on competing microscale damage mechanisms. Finite element simulations incorporate fiber–matrix interface debonding with cohesive zones and matrix damage with a smeared crack band approach in a unidirectional carbon–carbon composite. Results from a variance-based global sensitivity analysis identifies interfacial and matrix damage parameters as the primary source of variability in fracture behavior. Sobol’ indices indicate that matrix and cohesive zone strengths contribute 94% of the variance in the effective ultimate stress. A local analysis elucidates the relationship between these constituent strength parameters and failure mode by estimating the probability of cohesive, matrix, and mixed-mode dominated failure. Based on the results for 4000 simulations, 93% exhibit mixed-mode or interfacial dominated failure, which underscores the crucial role of fiber–matrix interface debonding in the transverse tensile failure of carbon–carbon composites. These uncertainty quantification results facilitate more efficient model calibration and provide a framework for microstructure-informed failure predictions in the face of manufacturing-induced uncertainty.

36 MATERIALS SCIENCE↗

Theoretical Correlation of Elemental Distribution of Nd and Pr in Ce-Fe-B Microstructure With Hard Magnetic Properties

Relatively resource-rich but property inferior-Ce-Fe-B magnet can be improved by partial replacement of Ce by Nd and/or Pr. In addition to the amount of Nd/Pr, their distribution profile in microstructure plays an important role. From our first principles density functional theory (DFT) calculation, the substitution energy of Ce by Pr/Nd is negative in Ce 2 Fe 14 B (2:14:1) while that for laves phase, CeFe 2 is positive, implying that Nd/Pr stabilize 2:14:1 and suppress the formation of the CeFe 2 phase. Further, micromagnetic simulation indicates that homogenized distribution of Nd/Pr improves squareness of demagnetization curve, while core (Ce-rich)-shell (Nd/Pr-rich) 2:14:1 grain structure enhances coercivity. Magnetic properties of Ce-Fe-B can be optimized by manipulating distribution profile of chemical element in microstructure based on their subtle difference in thermodynamic property, which is an effective pathway to design optimized chemical composition and processing route for high-performance magnet.

36 MATERIALS SCIENCE↗

Application of synchrotron radiation computed microtomography for quantification of bone microstructure in human and rat bones

This work aims to evaluate histomorphometric quantification by synchrotron radiation computed microto-mography in bones of human and rat specimens. Bones specimens are classified as normal and pathological (for human samples) and irradiated and non-irradiated samples (for rat ones). Human bones are specimens which were affected by some injury, or not. Rat bones are specimens which were irradiated, simulating radiotherapy procedures, or not. Images were obtained on SYRMEP beamline at the Elettra Synchrotron Laboratory in Trieste, Italy. The system generated 14 {mu}m tomographic images. The quantification of bone structures were performed directly by the 3D rendered images using a home-made software. Resolution yielded was excellent what facilitate quantification of bone microstructures.

60 APPLIED LIFE SCIENCES↗

Atomistic studies of nucleation of He clusters and bubbles in bcc iron

Atomistic simulations of the nucleation of He clusters and bubbles in bcc iron at 800 K have been carried out using the newly developed Fe-He interatomic potential, along with Ackland potential for the Fe-Fe interactions. Microstructure changes were analyzed in detail. We found that a He cluster with four He atoms is able to push out an iron interstitial from the cluster, creating a Frenkel pair. Small He clusters and self-interstitial atom (SIA) can migrate in the matrix, but He-vacancy (He-V) clusters are immobile. Most SIAs form <111> clusters, and only the dislocation loops with a Burgers vector of b =1/2<111> appear in the simulations. SIA clusters (or loops) are attached to He-V clusters for He implantation up to 1372 appm, while the He-V cluster-loop complexes with more than one He-V cluster are formed at the He concentration of 2057 appm and larger.

74 ATOMIC AND MOLECULAR PHYSICS↗