Search NASA⌕ Search

SEARCH · Search NASA

Results for “patterned beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

A square multiflare horn with 1-megawatt CW power-handling capability

The analysis and low-power testing of a square multiflare horn designed for 1-megawatt CW operation is described. Design considerations for the five-port input section are discussed. The required aperture modes are determined from radiation pattern considerations, and analysis of the multiflare section is carried out using mode matching. Measurements demonstrate that a circularly symmetric beam is produced with relatively low sidelobes.

Hoppe, Dan↗

A novel antenna for ultra-wide-band applications

An ultrawideband antenna based on a slotline feed structure, a bowtie horn, and a rolled edge termination was developed, analyzed, and measured. Empirical data showed that its beamwidths and bandwidth are dependent on its physical dimensions which are easily controllable by an antenna designer. Measured patterns of models with various radiation properties are shown to substantiate these design rules. A flat plateau-like main beam, low voltage standing-wave ratio (VSWR), the ability to produce both wide (60 deg) and narrow (30 deg) half-power beamwidths, low sidelobes and backlobe (40-50 dB down), low cross-polarized levels (20-25 dB down), and independent control of E- and H-plane beamwidths over an ultrawide bandwidth, say 2-18 GHz, are some of the strong points of this antenna type.

Lai, Albert K. Y.↗

A method using focal plane analysis to determine the performance of reflector antennas

Reflector antenna optimization schemes using array feeds have been used to recover antenna losses resulting from antenna distortions and aberrations and to generate contour coverage patterns. Historically, these optimizations have been carried out using the antenna far-field scattered patterns. The far-field patterns must be calculated separately for each of the array feed elements. For large or complex antennas (which include beam-waveguide antennas), the far-field calculation times can be prohibitive. This article presents a method with which the optimization can be carried out in the antenna focal region, where the scattering calculation needs only to be done once independently of the number of the elements in the array. This article also includes the results of a study, utilizing this unique technique, to determine the capabilities and limitations of using array feeds to compensate for gravitational induced losses in large reflector antennas.

Cramer, P. W.↗

Beat-type Langmuir wave emissions associated with a type III solar radio burst: Evidence of parametric decay

Recent measurements from the plasma wave instrument on the Galileo spacecraft have shown that Langmuir waves observed in conjunction with a type III solar radio burst contain many beat-type waveforms, with beat frequencies ranging from about 150 to 650 Hz. Strong evidence exists that the beat pattern is produced by two closely spaced narrowband components. The most likely candidates for these two waves are a beam-generated Langmuir wave and an oppositely propagating Langmuir wave produced by parametric decay. In the parametric decay process, nonlinear interactions cause the beam-driven Langmuir wave to decay into a Langmuir wave and a low-frequency ion sound wave. Comparisons of the observed beat frequency are in good agreement with theoretical predictions for a three-wave parametric decay process. Weak low-frequency emissions are also sometimes observed at the predicted frequency of the ion sound wave.

Hospodarsky, G. B.↗

Catastrophe Optics Method to Determine the Micro-Nano Size Profiles at TPL of Liquid Films on a Solid Surface

As discovered by recent studies, what directly affects the wetting and spreading is curvature in micro-region rather than the macroscopic contact angle. Measuring the profile of the micro-region becomes an important research topic. Recently, catastrophe optics has been applied to this kind of measurements. Optical catastrophe occurring in far field of waves of liquid-refracted laser beam implies a wealth of information about the liquid spreading not only for liquid drops but also for films. When a parallel laser beam passes through a liquid film on a slide glass at three-phase-line (TPL), very interesting optical image patterns occur on a screen far from the film. An analysis based on catastrophe optics discloses and interprets the formation of these optical image patterns. The analysis reveals that the caustic line manifested as the bright-thick line on the screen implies the lowest hierarchy of optical catastrophes, called fold caustic. This optical catastrophe is produced by the inflexion line on liquid surface at the liquid foot, which is formed not only in the spreading of drops but also in spreading of films. The generalized catastrophe optics method enables to identify the edge profiles and determine the edge foot height of liquid films. Keywords: Crossover region, Inflexion line, liquid edge foot, Catastrophe optics, Caustic and diffraction

Chao, David F.↗

Pre-Launch Performance Trending of Joint Polar Satellite System (JPSS) Advanced Technology Microwave Sounder (ATMS)

The Advanced Technology Microwave Sounder (ATMS) microwave radiometer instrument is utilized on-board NOAA’s Joint Polar Satellite System (JPSS) fleet of spacecraft to perform temperature and water vapor soundings of Earth’s atmosphere. Consisting of 22 channels over a frequency range from 22 to 183 GHz, ATMS provides high-impact observations for numerical weather prediction (NWP) models. A general description of the ATMS instrument is discussed in [1]. There are five ATMS flight units in the polar-orbiting JPSS program; three are currently on-orbit and two are pending launch. The first ATMS was flown on the Suomi National Polar-orbiting Partnership (SNPP) satellite, launched in 2011. The second ATMS was launched on the NOAA-20 (previously JPSS-1) satellite in 2017. The third ATMS was launched on the NOAA-21 (previously JPSS-2) satellite in 2022. The SNPP and NOAA-20 ATMS units are operational. The NOAA-21 ATMS unit is completing on-orbit commissioning and checkout, having achieved provisional maturity status in December 2022 with validated maturity expected in May 2023 [2]. The fourth and fifth ATMS units are planned for the JPSS-3 (launch ~2028) and JPSS-4 (launch ~2032) satellites [3]. This paper will focus on trending performance characteristics of each JPSS ATMS build from the pre-launch activities. Pre-launch trending of some parameters have been previously published up to the JPSS-3 mission [4][5]. This paper differs from and expands the scope of the prior work as it will include all five of the JPSS ATMS builds. The entire suite of JPSS ATMS units have completed their pre-ship instrument-level I&T and verification activities. These activities include a radiometric performance characterization of each instrument. In addition to comparing the performance across builds, the performance will also be compared to requirements and specifications where applicable. The on-orbit performance of the launched units will be excluded from the scope of this paper in order to focus on evaluations that are common across all builds. The post-launch performance of SNPP ATMS is detailed in [1][6][7][8]. The post-launch performance of NOAA-20 ATMS is detailed in [6][8][9]. The pre-launch characterization of the ATMS occurs at both subassembly-level and instrument-level testing. The antenna subsystem is tested at Northrop Grumman’s Compact Antenna Test Range (CATR) in Azusa, CA [9]. This testing characterizes the antenna pattern and the pointing performance of the scan drive mechanism and antenna subsystem. Trended parameters from this evaluation will include beam pointing accuracy, beamwidth, and beam efficiency. These parameters are captured in each instrument’s Calibration Data Book [10]. Instrument-level radiometric performance evaluation is primarily done during thermal vacuum (TVAC) calibration testing at Northrop Grumman’s Azusa, CA facility [9]. A general description of the calibration activities is presented in [1][9]. The testing involves inferring a scene target brightness temperature (TB) and comparing it to the actual scene TB while the instrument is at flight-like temperature and pressure environmental conditions. Trended parameters from this activity will include Noise Equivalent Delta Temperature (NEDT), nonlinearity, radiometric accuracy, gain stability, striping, and inter-channel noise correlation. The trending evaluation will allow for a direct comparison of the ATMS performance across builds. The paper will highlight observed performance improvements.

Edward J Kim↗

Bulk nanofabrication with single atomic plane precision via atomic-level sculpting of crystalline oxides

A method for sculpting crystalline oxide structures for bulk nanofabrication is provided. The method includes the controlled electron beam induced irradiation of amorphous and liquid phase precursor solutions using a scanning transmission electron microscope. The atomically focused electron beam includes operating parameters (e.g., location, dwell time, raster speed) that are selected to provide a higher electron dose in patterned areas and a lower electron dose in non-patterned areas. Concurrently with the epitaxial growth of crystalline features, the present method includes scanning the substrate to provide information on the size of the crystalline features with atomic resolution. This approach provides for atomic level sculpting of crystalline oxide materials from a metastable amorphous precursor and the liquid phase patterning of nanocrystals.

36 MATERIALS SCIENCE↗

Clarification of enhanced ferromagnetism in Be-codoped InMnP fabricated using Mn/InP:Be bilayers grown by molecular beam epitaxy

The p-type InMnP:Be epilayers were prepared by the sequential growth of Mn/InP:Be bilayers using molecular-beam-epitaxy and the subsequent in-situ annealing at 200-300 deg. C. In triple-axis x-ray diffraction patterns, the samples revealed a shoulder peak indicative of intrinsic InMnP. The ferromagnetic transition in InMnP:Be was observed to occur at the elevated temperature of {approx}140 K, and the ferromagnetic spin-domains clearly appeared in magnetic force microscopy images. The improved ferromagnetic properties are attributed to the increased p-d hybridation due to high p-type conductivity of InMnP:Be (p {approx} 10{sup 20 }cm{sup -3}). The results suggest that enhanced ferromagnetism can be effectively obtained from Be-codoped InMnP.

36 MATERIALS SCIENCE↗

Statistical Characterization and Process Control for Improved Growth of La2−xSrxCuO4 Films

We have used combinatorial molecular beam epitaxy (COMBE) technique to deposit thin cuprate films with continuous spread in chemical composition, as well as nominally uniform films. We have patterned them into linear pixel arrays and measured the transport properties of each pixel. We applied detailed statistical analysis to differentiate between various possible sources of random pixel-to-pixel variations, and utilized this knowledge to considerably tighten the process parameters and significantly reduce such variations. The density and quality of data points is high enough to allow detection of quantum phase transitions induced by tuning the chemical composition.

36 MATERIALS SCIENCE↗

Direct-write laser-assisted patterning of form birefringence in wave plates fabricated by glancing-angle deposition

The development of optics that provide spatial control of birefringence could enable better control of laser beam polarization, but available solutions are limited. Here we demonstrate a method to locally modify the birefringence of wave plates fabricated by glancing-angle deposition. The method employs localized melting of the anisotropic microstructure in a vacuum environment to alter the local birefringence. We demonstrate that this process is only possible under high vacuum to avoid trapping air within the melt zone. The direct-write method presented here can be readily utilized for coatings exhibiting form birefringence of virtually any chemical composition, size, and format.

42 ENGINEERING↗

A high-transparency, micro-patternable chip for X-ray diffraction analysis of microcrystals under native growth conditions

A highly X-ray-transparent, silicon nitride-based device has been designed and fabricated to harvest protein microcrystals for high-resolution X-ray diffraction data collection using microfocus beamlines and XFELs. Microcrystals present a significant impediment to the determination of macromolecular structures by X-ray diffraction methods. Although microfocus synchrotron beamlines and X-ray free-electron lasers (XFELs) can enable the collection of interpretable diffraction data from microcrystals, there is a need for efficient methods of harvesting small volumes (<2 µl) of microcrystals grown under common laboratory formats and delivering them to an X-ray beam source under native growth conditions. One approach that shows promise in overcoming the challenges intrinsic to microcrystal analysis is to pair so-called ‘fixed-target’ sample-delivery devices with microbeam-based X-ray diffraction methods. However, to record weak diffraction patterns it is necessary to fabricate devices from X-ray-transparent materials that minimize background scattering. Presented here is the design of a new micro-diffraction device consisting of three layers fabricated from silicon nitride, photoresist and polyimide film. The chip features low X-ray scattering and X-ray absorption properties, and uses a customizable blend of hydrophobic and hydrophilic surface patterns to help localize microcrystals to defined regions. Microcrystals in their native growth conditions can be loaded into the chips with a standard pipette, allowing data collection at room temperature. Diffraction data collected from hen egg-white lysozyme microcrystals (10–15 µm) loaded into the chips yielded a complete, high-resolution (<1.6 Å) data set sufficient to determine a high-quality structure by molecular replacement. The features of the chip allow the rapid and user-friendly analysis of microcrystals grown under virtually any laboratory format at microfocus synchrotron beamlines and XFELs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advances in Measurement of Skin Friction in Airflow

The surface interferometric skin-friction (SISF) measurement system is an instrument for determining the distribution of surface shear stress (skin friction) on a wind-tunnel model. The SISF system utilizes the established oil-film interference method, along with advanced image-data-processing techniques and mathematical models that express the relationship between interferograms and skin friction, to determine the distribution of skin friction over an observed region of the surface of a model during a single wind-tunnel test. In the oil-film interference method, a wind-tunnel model is coated with a thin film of oil of known viscosity and is illuminated with quasi-monochromatic, collimated light, typically from a mercury lamp. The light reflected from the outer surface of the oil film interferes with the light reflected from the oil-covered surface of the model. In the present version of the oil-film interference method, a camera captures an image of the illuminated model and the image in the camera is modulated by the interference pattern. The interference pattern depends on the oil-thickness distribution on the observed surface, and this distribution can be extracted through analysis of the image acquired by the camera. The oil-film technique is augmented by a tracer technique for observing the streamline pattern. To make the streamlines visible, small dots of fluorescentchalk/oil mixture are placed on the model just before a test. During the test, the chalk particles are embedded in the oil flow and produce chalk streaks that mark the streamlines. The instantaneous rate of thinning of the oil film at a given position on the surface of the model can be expressed as a function of the instantaneous thickness, the skin-friction distribution on the surface, and the streamline pattern on the surface; the functional relationship is expressed by a mathematical model that is nonlinear in the oil-film thickness and is known simply as the thin-oil-film equation. From the image data acquired as described, the time-dependent oil-thickness distribution and streamline pattern are extracted and by inversion of the thin-oil-film equation it is then possible to determine the skin-friction distribution. In addition to a quasi-monochromatic light source, the SISF system includes a beam splitter and two video cameras equipped with filters for observing the same area on a model in different wavelength ranges, plus a frame grabber and a computer for digitizing the video images and processing the image data. One video camera acquires the interference pattern in a narrow wavelength range of the quasi-monochromatic source. The other video camera acquires the streamline image of fluorescence from the chalk in a nearby but wider wavelength range. The interference- pattern and fluorescence images are digitized, and the resulting data are processed by an algorithm that inverts the thin-oil-film equation to find the skin-friction distribution.

Brown, James L.↗

Lateral ordering of GaAs nanowhiskers on GaAs(111)As and GaAs (110) surfaces during molecular-beam epitaxy

Possibilities of obtaining laterally ordered arrays of GaAs nanowhiskers on GaAs (110) and GaAs(111)As surfaces during the molecular beam epitaxy are considered. As in the case of the GaAs(111)As substrate, nanowhiskers are formed in the hexagonal phase on the GaAs(110) surface, which is also confirmed by the patterns of the reflection high-energy electron diffraction (obtained during the growth of nanowhiskers) and by the photoluminescence spectra.

36 MATERIALS SCIENCE↗

NanoFIBrication of a two-dimensional phononic crystal in a free standing membrane.

A two-dimensional phononic crystal (PnC) that can operate in the GHz range is created in a freestanding silicon substrate using NanoFIBrication (using a focused ion beam (FIB) to fabricate nanostructures). First, a simple cubic 6.75 x 6.75 ?m array of vias with 150 nm spacing is generated. After patterning the vias, they are backfilled with void-free tungsten scatterers. Each via has a diameter of 48 nm. Numerical calculations predict this 2D PnC will generate a band gap near 22 GHz. A protective layer of chromium on top of the thin (100 nm) silicon membrane confines the surface damage to the chromium, which can be removed at a later time. Inspection of the underside of the membrane shows the vias flaring out at the exit, which we are dubbing the 'trumpet effect'. The trumpet effect is explained by modeling the lateral damage in a freestanding membrane.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

TRMM Precipitation Radar Reflectivity Profiles Compared to High-Resolution Airborne and Ground-Based Radar Measurements

In this paper, TRMM (Tropical Rainfall Measuring Mission Satellite) Precipitation Radar (PR) products are evaluated by means of simultaneous comparisons with data from the high-altitude ER-2 Doppler Radar (EDOP), as well as ground-based radars. The comparison is aimed primarily at the vertical reflectivity structure, which is of key importance in TRMM rain type classification and latent heating estimation. The radars used in this study have considerably different viewing geometries and resolutions, demanding non-trivial mapping procedures in common earth-relative coordinates. Mapped vertical cross sections and mean profiles of reflectivity from the PR, EDOP, and ground-based radars are compared for six cases. These cases cover a stratiform frontal rainband, convective cells of various sizes and stages, and a hurricane. For precipitating systems that are large relative to the PR footprint size, PR reflectivity profiles compare very well to high-resolution measurements thresholded to the PR minimum reflectivity, and derived variables such as bright band height and rain types are accurate, even at high PR incidence angles. It was found that for, the PR reflectivity of convective cells small relative to the PR footprint is weaker than in reality. Some of these differences can be explained by non-uniform beam filling. For other cases where strong reflectivity gradients occur within a PR footprint, the reflectivity distribution is spread out due to filtering by the PR antenna illumination pattern. In these cases, rain type classification may err and be biased towards the stratiform type, and the average reflectivity tends to be underestimated. The limited sensitivity of the PR implies that the upper regions of precipitation systems remain undetected and that the PR storm top height estimate is unreliable, usually underestimating the actual storm top height. This applies to all cases but the discrepancy is larger for smaller cells where limited sensitivity is compounded by incomplete beam filling. Users of level three TRMM PR products should be aware of this scale dependency.

Heymsfield, G. M.↗

Alternative beam configuration for a Canadian Ka-band satellite system

Satellite systems operating in the Ka-band have been proposed to offer wide band personal communications services to fixed earth terminals employing small aperture antennas as well as to mobile terminals. This requirement to service a small aperture antenna leads to a satellite system utilizing small spot beams. The traditional approach is to cover the service area with uniform spot beams which have been sized to provide a given grade of service at the worst location over the service area and to place them in a honeycomb pattern. In the lower frequency bands this approach leads to a fairly uniform grade of service over the service area due to the minimal effects of rain on the signals. At Ka-band, however, the effects of rain are quite significant. Using this approach over a large service area (e.g. Canada) where the geographic distribution of rain impairment varies significantly yields an inefficient use of satellite resources to provide a uniform grade of service. An alternative approach is to cover the service area using more than one spot beam size in effect linking the spot beam size to the severity of the rain effects in a region. This paper demonstrates how for a Canadian Ka-band satellite system, that the use of two spot beam sizes can provide a more uniform grade of service across the country as well as reduce the satellite payload complexity over a design utilizing a single spot beam size.

Hindson, Daniel J.↗

Beam Dynamics in PT Symmetric Optical Lattices

The possibility of parity-time (PT) symmetric periodic potentials is investigated within the context of optics. Beam dynamics in this new type of optical structures is examined in detail for both one- and two-dimensional lattice geometries. It is shown that PT periodic structures can exhibit unique characteristics stemming from the nonorthogonality of the associated Floquet-Bloch modes. Some of these features include double refraction, power oscillations, and eigenfunction unfolding as well as nonreciprocal diffraction patterns.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

{beta} decay of {sup 81}Zn and migrations of states observed near the N=50 closed shell

The {beta} decay of the N=51 nucleus {sup 81}Zn was studied by means of {beta}-{gamma} spectroscopy and from isotopically pure beams produced at the Holifield Radioactive Ion Beam Facility (HRIBF). We observe several competing {beta} transitions populating {sup 81}Ga that are interpreted as allowed Gamow-Teller decays to positive parity, core excited states, and first-forbidden decays to negative parity states. The measured {beta}-decay pattern suggests an assignment of I{sup {pi}}=5/2{sup +} for the {sup 81}Zn ground state. The systematics of core excited states in N=50 isotones indicate a strengthening of the N=40 subshell gap near {sup 78}Ni.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗