Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation codes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

The LSU-Argonne conversion electron spectrometer: A new detector for the X-Array and SATURN decay station

In this study, a new conversion electron detector has been commissioned at the ATLAS/ CARIBU facility at Argonne National Laboratory. The LSU-Argonne Conversion Electron Spectrometer (LACES) is a LN 2 -cooled Si(Li) detector system designed to be incorporated into a decay station that comprises the dedicated HPGe clover array with a box geometry (X -Array) and the Scintillator and Tape Using Radioactive Nuclei (SATURN) device. This integration enables simultaneous measurements of conversion electrons and gamma-rays in decay experiments, yielding novel information on transition multipolarities, electric monopole transitions, and isomeric states that decay mostly via conversion electrons. A measurement of the energy resolution of LACES yielded 2.3-keV FWHM at 975 keV for electrons and 1.3-keV FWHM at 75 keV for X-rays. A detailed study of the absolute detection efficiency (at 5 mm from the source) was performed, where this quantity was determined experimentally in the range of electron transition energies between 25.5 keV and 1047.8 keV and subsequently simulated using the GEANT4 code. Measurement and simulations are found to be in excellent agreement. A precise characterization, for this type of detector system, of the absolute detection efficiency for such a wide energy range is reported for the first time.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Equipartition and the Temperature of Maximum Density of TIP4P/2005 Water

Here, we simulate TIP4P/2005 water in the temperature range of 257 to 318 K with time-steps δ = 0.25, 0.50, 1.00, 2.00, and 4.00 fs. The density–temperature behavior obtained using 0.25 or 0.50 fs is in excellent agreement with each other but differs from those obtained using time steps that have been shown earlier to lead to a breakdown of equipartition. For δt = 0.25 or 0.50 fs, the temperature of maximum density (TMD) is 277.15 K and the density value is in close agreement with experiments. For δt = 1.00 fs, the TMD is 277.15 K, but the density value is shifted higher. For the other time steps considered here, the TMD is shifted to progressively lower values for longer time steps, a trend that holds for different thermostat/barostat combinations. Enhancing the water–water dispersion interaction, as has been recommended for simulating disordered proteins in TIP4P/2005, degrades the description of the liquid–vapor phase envelope. We present a simple physically transparent explanation that highlights the separation of the time scales between translational and rotational motion. We also develop a metric, χ, that we term the equipartition anomaly, to detect equipartition violations in simulations that include molecules that are treated as rigid objects. Calculating χ is shown to be straightforward and sensitive to equipartition violations. A key takeaway from this study is that using sufficiently short time steps (≤0.5 fs) to preserve equipartition is essential for obtaining meaningful liquid water properties and for producing reliable simulation data, as correct ensemble sampling is fundamental to ensure reproducibility across codes and simulation algorithms.

Asthagiri, Dilipkumar N. [Oak Ridge National Labor↗

Two-Phase Turbulent Kinetic Energy Budget Computation in Co-Current Taylor Bubble Flow

Simulation of two-phase flows is relevant for reactor design and safety at normal operation or during accident scenarios. Often, the two-phase flow is in a regime in which slugs are formed or where the flow stratifies. Modeling such situations using standard single-phase Reynolds-averaged Navier-Stokes (RANS) turbulence models fails due to an overestimation of the eddy viscosity at the resolved two-phase interface. To solve this, an ad hoc turbulence damping term has been proposed in the literature that reduces the turbulence production locally at a two-phase interface, analogously to turbulence wall functions. However, this approach must be tailored to the specific setting and does not consider physical contributions such as surface tension or flow topology. Therefore, the problem of two-phase interfacial turbulence must be studied more in-depth. In this work, we consider co-current turbulent Taylor bubble flow using high-fidelity numerical simulation. The Basilisk code is used to simulate a Taylor bubble rising in a vertical pipe. By simulating the bubble in a moving frame of reference, we may study the turbulent kinetic energy (TKE) budgets ahead of the bubble, in its wake, and across the interface. The implementation of the TKE budget computation and the underlying averaging techniques are validated for the single-phase region ahead of the Taylor bubble using reference direct numerical simulation data. The analysis of the TKE budgets in the setting of Taylor bubble flow allows for the study of how turbulence behaves due to the presence of a two-phase interface and, in turn, supports the improvement of two-phase RANS models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

THE PROPERTIES OF X-RAY COLD FRONTS IN A STATISTICAL SAMPLE OF SIMULATED GALAXY CLUSTERS

We examine the incidence of cold fronts in a large sample of galaxy clusters extracted from a (512 h {sup -1} Mpc) hydrodynamic/N-body cosmological simulation with adiabatic gas physics computed with the Enzo adaptive mesh refinement code. This simulation contains a sample of roughly 4000 galaxy clusters with M {>=}10{sup 14} M{sub sun} at z = 0. For each simulated galaxy cluster, we have created mock 0.3-8.0 keV X-ray observations and spectroscopic-like temperature maps. We have searched these maps with a new automated algorithm to identify the presence of cold fronts in projection. Using a threshold of a minimum of 10 cold front pixels in our images, corresponding to a total comoving length L{sub cf}>156 h {sup -1} kpc, we find that roughly 10%-12% of all projections in a mass-limited sample would be classified as cold front clusters. Interestingly, the fraction of clusters with extended cold front features in our synthetic maps of a mass-limited sample trends only weakly with redshift out to z = 1.0. However, when using different selection functions, including a simulated flux limit, the trending with redshift changes significantly. The likelihood of finding cold fronts in the simulated clusters in our sample is a strong function of cluster mass. In clusters with M>7.5 x 10{sup 14} M{sub sun} the cold front fraction is 40%-50%. We also show that the presence of cold fronts is strongly correlated with disturbed morphology as measured by quantitative structure measures. Finally, we find that the incidence of cold fronts in the simulated cluster images is strongly dependent on baryonic physics.

79 ASTRONOMY AND ASTROPHYSICS↗

Radiation-Hydrodynamic Simulations of Massive Star Formation with Protostellar Outflows

We report the results of a series of AMR radiation-hydrodynamic simulations of the collapse of massive star forming clouds using the ORION code. These simulations are the first to include the feedback effects protostellar outflows, as well as protostellar radiative heating and radiation pressure exerted on the infalling, dusty gas. We find that that outflows evacuate polar cavities of reduced optical depth through the ambient core. These enhance the radiative flux in the poleward direction so that it is 1.7 to 15 times larger than that in the midplane. As a result the radiative heating and outward radiation force exerted on the protostellar disk and infalling cloud gas in the equatorial direction are greatly diminished. The simultaneously reduces the Eddington radiation pressure barrier to high-mass star formation and increases the minimum threshold surface density for radiative heating to suppress fragmentation compared to models that do not include outflows. The strength of both these effects depends on the initial core surface density. Lower surface density cores have longer free-fall times and thus massive stars formed within them undergo more Kelvin contraction as the core collapses, leading to more powerful outflows. Furthermore, in lower surface density clouds the ratio of the time required for the outflow to break out of the core to the core free-fall time is smaller, so that these clouds are consequently influenced by outflows at earlier stages of collapse. As a result, outflow effects are strongest in low surface density cores and weakest in high surface density one. We also find that radiation focusing in the direction of outflow cavities is sufficient to prevent the formation of radiation pressure-supported circumstellar gas bubbles, in contrast to models which neglect protostellar outflow feedback.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

THREE-DIMENSIONAL SIMULATIONS OF GYROSYNCHROTRON EMISSION FROM MILDLY ANISOTROPIC NONUNIFORM ELECTRON DISTRIBUTIONS IN SYMMETRIC MAGNETIC LOOPS

Microwave emission of solar flares is formed primarily by incoherent gyrosynchrotron radiation generated by accelerated electrons in coronal magnetic loops. The resulting emission depends on many factors, including pitch-angle distribution of the emitting electrons and the source geometry. In this work, we perform systematic simulations of solar microwave emission using recently developed tools (GS Simulator and fast gyrosynchrotron codes) capable of simulating maps of radio brightness and polarization as well as spatially resolved emission spectra. A three-dimensional model of a symmetric dipole magnetic loop is used. We compare the emission from isotropic and anisotropic (of loss-cone type) electron distributions. We also investigate effects caused by inhomogeneous distribution of the emitting particles along the loop. It is found that the effect of the adopted moderate electron anisotropy is the most pronounced near the footpoints and it also depends strongly on the loop orientation. Concentration of the emitting particles at the looptop results in a corresponding spatial shift of the radio brightness peak, thus reducing effects of the anisotropy. The high-frequency ({approx}> 50 GHz) emission spectral index is specified mainly by the energy spectrum of the emitting electrons; however, at intermediate frequencies (around 10-20 GHz), the spectrum shape is strongly dependent on the electron anisotropy, spatial distribution, and magnetic field nonuniformity. The implications of the obtained results for the diagnostics of the energetic electrons in solar flares are discussed.

79 ASTRONOMY AND ASTROPHYSICS↗

THE IMPACT OF THE SUPERSONIC BARYON-DARK MATTER VELOCITY DIFFERENCE ON THE z {approx} 20 21 cm BACKGROUND

Recently, Tseliakhovich and Hirata showed that during the cosmic Dark Ages the baryons were typically moving supersonically with respect to the dark matter with a spatially variable Mach number. Such supersonic motion may source shocks that inhomogeneously heat the universe. This motion may also suppress star formation in the first halos. Even a small amount of coupling of the 21 cm signal to this motion has the potential to vastly enhance the 21 cm brightness temperature fluctuations at 15 {approx}< z {approx}< 40, as well as to imprint distinctive acoustic oscillations in this signal. We present estimates for the size of this coupling, which we calibrate with a suite of cosmological simulations of the high-redshift universe using the GADGET and Enzo codes. Our simulations, discussed in detail in a companion paper, are initialized to self-consistently account for gas pressure and the dark matter-baryon relative velocity, v {sub bc} (in contrast to prior simulations). We find that the supersonic velocity difference dramatically suppresses structure formation on 10-100 comoving kpc scales, it sources shocks throughout the universe, and it impacts the accretion of gas onto the first star-forming minihalos (even for halo masses as large as 10{sup 7} M {sub Sun }). However, prior to reheating by astrophysical sources, we find that the v {sub bc}-sourced temperature fluctuations can contribute only as much as Almost-Equal-To 10% of the fluctuations in the 21 cm signal. We do find that v {sub bc} in certain scenarios could source an O(1) component in the power spectrum of the 21 cm background on observable scales via the X-ray (but not ultraviolet) backgrounds produced once the first stars formed. In a scenario in which {approx}10{sup 6} M {sub Sun} minihalos reheated the universe via their X-ray backgrounds, we find that the pre-reionization 21 cm signal would be larger than previously anticipated and exhibit more significant acoustic features. Such features would be a direct probe of the first stars and black holes. In addition, we show that structure formation shocks are unable to heat the universe sufficiently to erase a strong 21 cm absorption trough at z {approx} 20 that is found in most models of the sky-averaged 21 cm intensity.

79 ASTRONOMY AND ASTROPHYSICS↗

Irradiation of gold nanoparticles by x-rays: Monte Carlo simulation of dose enhancements and the spatial properties of the secondary electrons production

Purpose: The aim of this study is to understand the characteristics of secondary electrons generated from the interaction of gold nanoparticles (GNPs) with x-rays as a function of nanoparticle size and beam energy and thereby further the understanding of GNP-enhanced radiotherapy. Methods: The effective range, deflection angle, dose deposition, energy, and interaction processes of electrons produced from the interaction of x-rays with a GNP were calculated by Monte Carlo simulations. The GEANT4 code was used to simulate and track electrons generated from a 2, 50, and 100 nm diameter GNP when it is irradiated with a 50 kVp, 250 kVp, cobalt-60, and 6 MV photon beam in water. Results: When a GNP was present, depending on the beam energies used, secondary electron production was increased by 10- to 2000-fold compared to an absence of a GNP. Low-energy photon beams were much more efficient at interacting with the GNP by two to three orders of magnitude compared to MV energies and increased the deflection angle. GNPs with larger diameters also contributed more dose. The majority of the energy deposition was outside the GNP, rather than self-absorbed by the nanoparticle. The mean effective range of electron tracks for the beams tested ranged from approximately 3 {mu}m to 1 mm. Conclusions: These simulated results yield important insights concerning the spatial distributions and elevated dose in GNP-enhanced radiotherapy. The authors conclude that the irradiation of GNP at lower photon energies will be more efficient for cell killing. This conclusion is consistent with published studies.

60 APPLIED LIFE SCIENCES↗

SU-E-T-132: Assess the Shielding of Secondary Neutrons From Patient Collimator in Proton Therapy Considering Secondary Photons Generated in the Shielding Process with Monte Carlo Simulation

Purpose: In this study we present Monte Carlo based evaluation of the shielding effect for secondary neutrons from patient collimator, and secondary photons emitted in the process of neutron shielding by combination of moderator and boron-10 placed around patient collimator. Methods: The PHITS Monte Carlo Simulation radiation transport code was used to simulate the proton beam (Ep = 64 to 93 MeV) from a proton therapy facility. In this study, moderators (water, polyethylene and paraffin) and boron (pure {sup 10}B) were placed around patient collimator in this order. The rate of moderator and boron thicknesses was changed fixing the total thickness at 3cm. The secondary neutron and photons doses were evaluated as the ambient dose equivalent per absorbed dose [H*(10)/D]. Results: The secondary neutrons are shielded more effectively by combination moderators and boron. The most effective combination of shielding neutrons is the polyethylene of 2.4 cm thick and the boron of 0.6 cm thick and the maximum reduction rate is 47.3 %. The H*(10)/D of secondary photons in the control case is less than that of neutrons by two orders of magnitude and the maximum increase of secondary photons is 1.0 µSv/Gy with the polyethylene of 2.8 cm thick and the boron of 0.2 cm thick. Conclusion: The combination of moderators and boron is beneficial for shielding secondary neutrons. Both the secondary photons of control and those emitted in the shielding neutrons are very lower than the secondary neutrons and photon has low RBE in comparison with neutron. Therefore the secondary photons can be ignored in the shielding neutrons.This work was supported by JSPS Core-to-Core Program (No.23003). This work was supported by JSPS Core-to-Core Program (No.23003)

60 APPLIED LIFE SCIENCES↗

Direct Modeling of Scintillator Thickness for Optimal Light Output and Spatial Resolution

It is common in x-ray radiography to use scintillators (e.g., BGO or LSO) to convert x-rays to visible light, which is then recorded by an imaging system. The response of the scintillator depends fundamentally on its thickness, with respect to both its visible light emittance and its spatial resolution. This is important for optimizing light output, signal to noise ratio, or optical response time. Given that it is often cost-prohibitive to procure a variety of scintillator samples and empirically test the performance, it is essential to be able to model and accurately simulate the performance of a scintillator with respect to thickness and other properties, and a direct way of doing this is using Monte Carlo-based radiation transport codes. Such simulations can be expensive in terms of computational time, and the codes are not easily obtained. In this work we first show such simulations, and demonstrate that there is a natural trade-off between light output of a scintillator and its spatial resolution. We then derive a first-principles model that accurately approximates the light output, using straightforward calculations that can be performed quickly with any basic computing software. We compare the results to those obtained from Monte Carlo simulations and show that our simplified model can be used to analyze the tradeoff between emittance and resolution nearly as well as using a full-scale radiation transport code.

Monte Carlo methods, X-ray imaging, scintillation ↗

CG-Kit: Code Generation Toolkit for performant and maintainable variants of source code applied to Flash-X hydrodynamics simulations

CG-Kit is a new Code Generation tool-Kit that we have developed as a part of the solution for portability and maintainability for multiphysics computing applications. The development of CG-Kit is rooted in the urgent need created by the shifting landscape of high-performance computing platforms and the algorithmic complexities of a particular large-scale multiphysics application: Flash-X. To efficiently use computing resources on a heterogeneous node, an application must have a map of computation to resources and a mechanism to move the data and computation to the resources according to the map. Most existing performance portability solutions are focussed on abstracting the expression of computations so that a unified source code can be specialized to run on different resources. However, such an approach is insufficient for a code like Flash-X, which has a multitude of code components that can be assembled in various permutations and combinations to form different instances of applications. Similar challenges apply to any code that has composability, where a single specified way of apportioning work among devices may not be optimal. Additionally, use cases arise where the optimal control flow of computation may differ for different devices while the underlying numerics remain identical. This combination leads to unique challenges including handling an existing large code base in Fortran and/or C/C++, subdivision of code into a great variety of units supporting a wide range of physics and numerical methods, different parallelization techniques for distributed and shared memory systems and accelerator devices, and heterogeneity of computing platforms requiring coexisting variants of parallel algorithms. All of these challenges demand that scientific software developers apply existing knowledge about domain applications, algorithms, and computing platforms to determine custom abstractions and granularity for code generation. There is a critical lack of tools to tackle those problems. CG-Kit is designed to fill this gap by providing a user with the ability to express their desired control flow and computation-to-resource map in the form a pseudocode-like recipe. It consists of standalone tools that can be combined into highly specific and, we argue, highly effective portability and maintainability toolchains. Here we present the design of our new tools: parametrized source trees, control flow graphs, and recipes. The tools are implemented in Python. They are agnostic to the programming language of the source code targeted for code generation. In conclusion, we demonstrate the capabilities of the toolkit with two examples, first, multithreaded variants of the basic AXPY operation, and second, variants of parallel algorithms within a hydrodynamics solver, called Spark, from Flash-X that operates on block-structured adaptive meshes.

Algorithmic portability↗

New Interfaces for the Plasimo Framework

The Plasimo code (http://www.plasimo.phys.tue.nl) is a multi-physics code for simulating a variety of plasma sources with various degrees of departures from equilibrium, electromagnetic field configurations, flow regimes and geometries. Plasimo's species data requirements are discussed from a developer's point of view. A detailed description is given of the implementation of cross section-averaging and the way a collisional-radiative model can be set up for arbitrary plasma gases. Some comments will be made concerning the recent work regarding the standardisation (using an XML representation) of input data that has been initiated during recent installments of the ICAMDATA conference. We will discuss possible future directions of the Plasimo project in the light of these developments and discuss the future role of such technologies like Schema, AJAX, Web Services and related web technologies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Sight on the Variation of Spectral Parameters in GRBs

Gamma ray bursts (GRBs) are high energy photons detected during a short interval of time. They are signs of the most energetic events in the universe. Photons detected show a non thermal spectrum, very well described by the peak energy and two smoothly connected power laws with different slopes or indices. This spectrum is named Band spectrum and serves actually as the most important source of information on their physical origin. It characterizes not only the overall emission, but also the instantaneous one, found in small successive intervals of time during the event. The time-resolved spectra show an obvious evolution in energy, which is generally accepted and supported by several arguments. There is also some evidence in measuring a kind of evolution in slope parameters, which would be considered as a serious source of information for the physical mechanism. In this work we try to examine the limit in observation bands, which we suspect as a reason for the apparent variation in time of spectral indices. Our work is based on a numeric and certified code. We simulate GRBs assuming synchrotron emission in the internal shocks model. For each time-resolved spectrum we find spectral parameters based on the Band function.

79 ASTRONOMY AND ASTROPHYSICS↗

Simulation Study of Current Drive Efficiency for KSTAR 5 GHz LHCD

Theoretical 5 GHz lower hybrid current drive (LHCD) efficiency using power spectrum given by 0-D Brambilla code and Lower Hybrid Simulation Code (LSC) have been studied for KSTAR. In LSC simulation, RF-driven current and current drive efficiency has been found to be deeply dependent on the profiles of the plasma density and temperature as well as on current profile in order to obtain hollow current profile favorable for advance tokamak operation mode and steady state operation. The peaked density and broad temperature profile control has been found to be efficient in current drive with maximum RF-driven current larger than 400 kA/MW with very high efficiency when the peak plasma density is ranged from 0.2 to 2.0x1020 m-3, and the peak electron temperature range of 2-20 keV together with toroidal field 2-3.5 T and Ip = 0.5-2 MA. The on-/off-axis current profile controllability is also investigated through parametric scan, and small negative magnetic shear is seen at the narrow region of the off-axis for very high temperature regime and for high BT and I{sub p}. In order to achieve the same for lower temperature regime Ip has to be lower and also for higher LH-power compromising with CD efficiency in this case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A hydrogeophysical framework to assess infiltration during a simulated ecosystem-scale flooding experiment

This study presents a framework to quantify changes in soil saturation in response to flooding caused by extreme hydrologic perturbation on coastal ecosystems at the interfaces and transition between terrestrial and aquatic systems. Subsurface heterogeneity limits the use of in situ measurements to quantify subsurface flow during flooding due to the spatial discontinuity in the measured data. While geophysical methods, including time-lapse electrical resistivity imaging (ERI), are increasingly used to monitor soil hydrological processes, their abilities to parameterize flow models have been underutilized. This study combines background ERI, ground penetrating radar (GPR), time-lapse ERI, soil characterization, and a numerical flow model developed using an Advanced Terrestrial Simulator (ATS) code to quantify the infiltration pathway and describe the hydrological dynamics during a simulated flooding experiment. We assessed the use of two conceptual models developed using [1] ERI and GPR data that described the stratigraphic distribution, and time-lapse ERI that mapped permeability contrast, and [2] information from a national soil database for capturing changes in saturation. Combining the ERI and GPR results with soil core data revealed the stratigraphic heterogeneity at the site with a silty clay layer from 1 to 2 m between an overlying loamy topsoil and an underlying saturated silty sand. This silty clay layer could restrict deep infiltration. The time-lapse ERI showed up to a 35% decrease in resistivity, which correlated with soil moisture data (R 2 value > 0.53) and revealed preferential infiltration zones used to inform the flow model. Numerical simulation results from both the geophysics- and soil database-informed models quantified changes in soil saturation with calculated soil moistures that agreed with field data. The geophysics-informed model captured more of the system’s variability, reflective of shallow subsurface heterogeneities. The framework presented will serve as a precursor for a robust ecohydrological model that can describe the impacts of extreme events induced by climate change on coastal ecosystems.

54 ENVIRONMENTAL SCIENCES↗

Fit Fly: A Case Study of Interconnect Innovation through Parallel Simulation

To meet the demand for exascale-level performance from high-performance computing (HPC) interconnects, many system architects are turning to simulation results for accurate and reliable predictions of the performance of prospective technologies. Testing full-scale networks with a variety of benchmarking tools, including synthetic workloads and application traces, can give crucial insight into what ideas are most promising without needing to physically construct a test network. While flexible, however, this approach is extremely compute time intensive. We address this time complexity challenge through the use of large-scale, optimistic parallel simulation that ultimately leads to faster HPC network architecture innovations. In this paper we demonstrate this innovation capability through a real-world network design case study. Specifically, we have simulated and compared four extreme-scale interconnects: Dragonfly, Megafly, Slim Fly, and a new dual-rail-dual-plane variation of the Slim Fly network topology. We present this new variant of Slim Fly, dubbed Fit Fly, to show how interconnect innovation and evaluation-beyond what is possible through analytic methods-can be achieved through parallel simulation. We validate and compare the model with various network designs using the CODES interconnect simulation framework. By running large-scale simulations in a parallel environment, we are able to quickly generate reliable performance results that can help network designers break ground on the next generation of high-performance network designs.

High Performance Computing↗

Dataset for manuscript "Equipartition and the temperature of maximum density of TIP4P/2005 water"

We simulate TIP4P/2005 water in the temperature range of 257 K to 318 K with time-steps 0.25, 0.50, 1.00, 2.00, and 4.00 fs. The density-temperature behavior obtained using 0.25 or 0.50 fs are in excellent agreement with each other but differ from those obtained using time-steps that have been shown earlier to lead to a breakdown of equipartition. The temperature of maximum density (TMD) is 277.15 K with time-step 0.25 or 0.50 fs, but is shifted to progressively lower values for longer time-steps, a trend that holds for different thermostat/barostat combinations. Enhancing the water-water dispersion interaction, as has been recommended for simulating disordered proteins in TIP4P/2005, degrades the description of the liquid-vapor phase envelope. We present a simple physically transparent reasoning to highlight the separation of the time-scales between translational and rotational motion. We also develop a metric, Chi, that we term the equipartition anomaly, to detect equipartition violations in simulations that include molecules that are treated as rigid objects. Calculating Chi is shown to be straightforward and sensitive to equipartition violations. A key takeaway from this study is that using sufficiently short time-steps (less than or equal to 0.5 fs) to preserve equipartition is essential for obtaining meaningful liquid water properties and for producing reliable simulation data, as correct-ensemble sampling is fundamental to ensure reproducibility across codes and simulation alogrithms. The included dataset provides the raw data used in the preparation of the graphs noted in the manuscript.

36 MATERIALS SCIENCE↗

MCNP 2020: Preparing LANL Monte Carlo for Exascale Computer Systems (White Paper)

The MCNP Monte Carlo code for simulating particle transport is the product of over 60 years of Monte Carlo code development at LANL. MCNP is the most-used code worldwide for particle transport in nuclear systems, with over 10,000 users in dozens of application areas. At LANL, MCNP is used extensively in applications for nuclear criticality safety, stockpile stewardship, homeland security, radiological safety, experiment design and analysis, etc., and is considered a critical technology resource for national defense. MCNP is often referred to as the “gold standard” for radiation transport calculations, based on the long development history and extensive validation work. Today, however, this critical technology and its well-deserved reputation are at risk. We propose a targeted effort over the next several years to upgrade the core software portions of the MCNP code. This effort will focus on fundamental structural changes to the underlying MCNP algorithms, data storage, and code architecture. These changes will directly improve code maintainability, reduce the development time for new features, improve the code performance, and make the code more flexible and adaptable for expected future computer systems. To move forward with new computer systems and additional new features, it is vital to have a solid base.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗