Search NASA⌕ Search

SEARCH · Search NASA

Results for “texturization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Tensile behavior and flow stress anisotropy of accumulative roll bonded Cu-Nb nanolaminates

The flow stress, ductility, and in-plane anisotropy are evaluated for bulk accumulative roll bonded copper-niobium nanolaminates with layer thicknesses ranging from 1.8 μm to 15 nm. Uniaxial tensile tests conducted parallel to the rolling direction and transverse direction demonstrate that ductility generally decreases with decreasing layer thickness; however, at 30 nm, both high strengths (1200 MPa) and significant ductility (8%) are achieved. The yield strength increases monotonically with decreasing layer thickness, consistent with the Hall-Petch relationship, and significant in-plane flow stress anisotropy is observed. Taylor polycrystal modeling is used to demonstrate that crystallographic texture is responsible for the in-plane anisotropy and that the effects of texture dominate even at nanoscale layer thicknesses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Examination of Through-Thickness/Through-Time Phase Evolution during an MOD-Type REBCO Precursor Conversion Using Raman Microsscopy

Through-thickness/through-time composition analyses were made on REBa{sub 2}Cu{sub 3}O{sub 6+x} (REBCO) films prepared from metal-organic deposited (MOD) precursors on a RABiTS (rolling-assisted biaxially textured substrate) template. Y Dy{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 6 + x} films were fabricated either by a single precursor coating or by two separate, equivalent precursor coatings with an intermediate decomposition. Specimens were quenched at selected times along a heat treatment profile that simulated conditions used by American Superconductor, then examined by Raman microscopy along mechanically milled slopes through the REBCO films. Upon reaching the reaction temperature TR, the precursor initially transforms into a (Y, Dy){sub 2}Cu{sub 2}O{sub 5}, CuO, Cu{sub 2}O, and RE-Ba-F-O phase mix, and this is followed shortly by substrate level REBCO formation that propagates upwards through time. Our results indicate that (1) the single layer (SL) and double layer (DL) films (both {approx} 1.2 {mu}m thick) react to completion at about the same rate and arrive at a similar final composition and (2) some residual Ba-Cu-O phases persist near the top of the fully reacted films. The performance of the SL film was moderately better than that of the DL film, seemingly due to better through-thickness REBCO texture as determined using x-ray diffraction.

36 MATERIALS SCIENCE↗

Processing of Dilute Mg–Zn–Mn–Ca Alloy/Nb Multilayers by Accumulative Roll Bonding

Recent advancements in the severe plastic deformation process called accumulative roll bonding (ARB) can help to address the long-standing need for manufacturing lightweight, high-strength Mg sheet materials. However, the fabrication of Mg alloy-based laminates via ARB remains a challenge due to the intrinsically poor formability of Mg. Herein, it is shown that Mg-based composite laminates with refined layers can be fabricated via several room-temperature ARB cycles with appropriate intermediate annealing and alloy selection. The final laminates made here consist of equal volume fractions of a dilute Mg–Zn–Mn–Ca alloy phase and a pure Nb phase with fine 150 μm layer thicknesses. Deformation texture evolution in both phases within the composite is analyzed via neutron diffraction measurements taken at different stages in the process. The analysis suggests that the annealing step recrystallizes the Mg-alloy phase. It is also shown that for both phases, the stabilized deformation textures within the composite correspond to the classic stable textures of the individual constituents. Polycrystal texture modeling implies that {10–12} <-1011> extension twinning developed in the Mg alloy during rolling.

36 MATERIALS SCIENCE↗

Study on the Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Ca Alloy Wire for Biomaterial Application

Due to their excellent biocompatibility and biodegradability, magnesium alloy wires have attracted much attention for biomaterial applications including orthopedic K-wires and sutures in wound closure. In this study, Mg-3Zn-0.2Ca alloy wires were prepared by cold drawing combined with proper intermediate annealing process. Microstructures, texture, mechanical properties and corrosion behavior of Mg-3Zn-0.2Ca alloy wire in a simulated body fluid were investigated. The results showed that the secondary phase and average grain size of the Mg-3Zn-0.2Ca alloy were refined in comparison with the as-extruded alloy and a strong (0002)<10-10>//DD basal fiber texture system was formed after multi-pass cold drawing. After the annealing, most of the basal planes were tilted to the drawing direction (DD) by about 35°, presenting the characteristics of random texture, and the texture intensity decreased. The as-annealed wire shows good mechanical properties with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 253 ± 8.5 MPa, 212 ± 11.3 MPa and 9.2 ± 0.9%, respectively. Electrochemical and hydrogen evolution measurements showed that the corrosion resistance of the Mg-3Zn-0.2Ca alloy wire was improved after the annealing. The immersion test indicated that the Mg-3Zn-0.2Ca wire exhibited uniform corrosion behavior during the initial period of immersion, but then exhibited local corrosion behavior.

36 MATERIALS SCIENCE↗

Influence of Rolling Temperature on the Mechanical Properties and Microstructure of Variable-Plane-Rolled Mg-3Al-1Zn Alloy

AZ31 magnesium alloy was produced via variable-plane rolling (VPR) under different temperatures. The effects of rolling temperature on the microstructure, texture and mechanical properties were investigated. A double-peak basal texture was formed during VPR treatment. Dynamic recrystallization (DRX) was observed during the VPR treatment, and it can reduce the texture intensity owing to the coalescence of sub-grains. Four types of twins were observed in the VPR treatment: {10-12} extension twins, {10-13}, {10-11} contraction twins and {10-11}-{10-12} double twins. The suitable temperature of AZ31 magnesium alloy for VPR treatment is determined as 623 K through experiments with tensile yield strength of 240 MPa, compressive yield strength of 162 MPa and elongation of 13%. Owing to the important impact of temperature on mechanical properties, the alloy was further VPRed with a decrease in temperature pass-by-pass. The high temperature of 623 K at the initial passes randomized the texture, which led to notably high ductility.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Copper Billets Fabricated by the Repetitive Extrusion and Free Forging Process

In the present study, with the aim of obtaining a weakened texture, grain refinement and improved mechanical properties, copper billets were successfully fabricated using the severe plastic deformation method of repetitive extrusion and free forging (REFF) without using any additional tools or devices. The evolution of the microstructure, texture and mechanical behavior of the ultrafine grain copper billets over an increasing number of REEF cycles was also systematically studied. Our results show that the effective strain per REFF process was ε = 2.35. After two cycles of REFF process, the sum effective strain became ε = 4.7, leading to high efficiency of grain refinement. The grain size was refined from 50 to 0.8 μm; the yield strength was increased to 462 MPa, and we obtained a weakened texture in the pure copper billets. By increasing the number of cycles, the grain refinement ability was decreased, and the texture was thus strengthened further. Therefore, two cycles of REFF were a reasonable process for producing ultrafine-grained copper billets.

36 MATERIALS SCIENCE↗

Influence of Torsion on Precipitation and Hardening Effects during Aging of an Extruded AZ91 Alloy

The effect of torsional deformation by various routes prior to artificial aging treatment on the microstructure of extruded AZ91 rods was investigated. The tension and compression properties along the extruded direction were tested to evaluate the hardening effect. The results showed that torsional deformation can largely enhance the subsequent age-hardening effect. A detailed microstructural characterization revealed that torsional deformation produced a high density of dislocations and {10-12} twins, which can promote continuous precipitation and increase the number density of the Mg{sub 17}Al{sub 12} phase. In addition, part of dislocations and the {10-12} twins were retained after aging treatment. The combination of the increased precipitation hardening by Mg{sub 17}Al{sub 12}, dislocation strengthening and refinement strengthening contributed to the high hardening effect. Moreover, the hardening effect can be further increased by tailoring the torsion route. The torsion route exhibited little influence on the age-hardening effect, while it remarkably affected the texture of the twisted AZ91 rods. Reciprocating torsion had little influence on the texture. In contrast, unidirectional torsion caused the c-axis of the texture to rotate toward the extrusion direction, resulting in a texture softening effect. Therefore, combining reciprocating torsion and aging caused a higher hardening effect than combining unidirectional torsion and aging. The detailed strengthening mechanism was analyzed and is discussed.

36 MATERIALS SCIENCE↗

Tailoring material microstructure and property in wire-laser directed energy deposition through a wiggle deposition strategy

Developing effective strategies to directly control material microstructure, property, and anisotropy is an active research area in metal additive manufacturing. This work develops a wiggle deposition pattern for wire-laser directed energy deposition (DED) of 316L stainless steel (SS) to modify the solidification texture, particularly in the building direction, in as-deposited samples. Through multi-physics simulation, operando near-infrared imaging, and synchrotron x-ray characterization, it is found that the wiggle deposition strategy induces highly dynamic melt flow and oscillating thermal gradient in the melt pool, which is responsible for the variation of preferable grain growth direction and crystallographic texture in the sample. The specific texture reduces the anisotropy in the tensile strength of as-printed 316L SS samples cut along different directions. Also, it largely increases the ductility along the build direction. Crystal plasticity simulation is performed to correlate the sample texture with mechanical property. In conclusion, this work offers a unique approach for tailoring local properties through the control of melt pool instability by applying different tool paths.

36 MATERIALS SCIENCE↗

Comparison of Forest Soil Carbon Dynamics at Five Sites Along a Latitudinal Gradient

Carbon stocks, and C:N ratios, were measured in the forest floor, mineral soil, and two mineral soil fractions (particulate and mineral-associated organic matter, POM and MOM, respectively) at five forest sites, ranging from 60 to 100 years old, along a latitudinal gradient in the eastern United States. Sampling at four sites was replicated over two consecutive years. For many measurements (like forest floor carbon stocks, cumulative soil organic carbon stocks to 20 cm, and the fraction of whole soil carbon in POM), there was no significant difference between years at each site despite the use of somewhat different sampling methods. With one exception, forest floor and mineral soil carbon stocks increased from warm, southern, sites (with fine-textured soils) to northern, cool, sites (with more coarse-textured soils). The exception was a northern site, with less than 10% silt-clay content, that had a soil organic carbon stock similar to those measured at southern sites. Soil carbon at each site was partitioned into two pools (labile and stable) on the basis of carbon measured in the forest floor and POM and MOM fractions from the mineral soil. A two-compartment steady-state model, with randomly varying parameter values, was used in probabilistic calculations to estimate the turnover time of labile soil organic carbon (MRTU) and the annual transfer of labile carbon to stable carbon (k2) at each site in two different years. Based on empirical data, the turnover time of stable soil carbon (MRTS) was determined by mean annual temperature and increased from 30 to 100 years from south to north. Moving from south to north, MRTU increased from approximately 5 to 14 years. Consistent with prior studies, 13C enrichment factors ( ) from the Rayleigh equation, that describe the rate of change in 13C through the soil profile, were an indicator of soil carbon turnover times along the latitudinal gradient. Consistent with its role in stabilization of soil organic carbon, silt-clay content along the gradient was positively correlated (r = 0.91; P 0.001) with parameter k2. Mean annual temperature was indicated as the environmental factor most strongly associated with south to north differences in the storage and turnover of labile soil carbon. However, soil texture appeared to override the influence of temperature when there was too little silt-clay content to stabilize labile soil carbon and thereby protect it from decomposition. Irrespective of latitudinal differences in measured soil carbon stocks, each study site had a relatively high proportion of labile soil carbon (approximately 50% of whole soil carbon to a depth of 20 cm). Depending on unknown temperature sensitivities, large labile pools of forest soil carbon are potentially at risk of depletion by decomposition in a warming climate, and losses could be disproportionately higher from coarse textured forest soils.

54 ENVIRONMENTAL SCIENCES↗

Direct observation of annealing-driven recrystallization behavior in magnesium alloy at low strain condition

Grain-twin interactions are significant in texture modification under thermodynamic driving force. In this study, annealing-driven twinning/detwinning behavior, grain growth, and corresponding texture evolution in a pre-deformed AZ31 magnesium alloy were systematically tracked and investigated via in-situ heating synchrotron X-ray diffraction and quasi in-situ electron backscattered diffraction techniques. A twinning texture is generated in the pre-deformed sample due to the activation of {$10\bar{1}2$} tensile twinning. During annealing, dislocation annihilation occurs between 100 and 280 °C, and recrystallization occurs above 280 °C, manifesting as the initial residual matrix and twins being competitively swallowed by each other, forming a bimodal texture. The recrystallization process is completed by boundary movement, which depends on the energy difference across the boundary. In addition, it is found that the grain boundaries favor movement towards the side with higher stored energy, regardless of the boundary type or the boundary energy.

In-situ observation↗

Impacts of annealing treatment on the microstructure of U-Mo monolithic fuel plates

The objective of this paper is to analyze the effect of different heat treatments on the fuel microstructure and texture in laboratory scale monolithic U-Mo fuel plates. Such analyses are relevant as they could possibly inform future fabrication methods for the optimization of microstructure and of material properties to ultimately improve fuel performance during irradiation. For this reason, detail characterization including Energy x-ray dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) techniques were applied on U-Mo plates fabricated with different heat treatments to understand the influence of fabrication on fuel microstructure. Here, U-Mo fresh fuel specimens with or without annealing treatments (homogenization and stress release annealing) after rolling were analyzed in this work. In this study for the first time EBSD was systematically used to analyze the heat treatments influence on texture present in fresh fuel monolithic U-Mo fuel plates. Such changes were connected to other known microstructural and chemical changes. In this work minimization of molybdenum concentration variation and gamma phase decomposition of the U-Mo fuel core after homogenization was observed. Also, an increase in the interaction layer of the U-Mo fuel core with the Zr interlayer diffusion barrier was observed with the UZr 2 growing up to 1 µm in thickness. Such microstructural changes were aligned to the changes in texture and grain structure. Indeed, common texture observed in body-centered cubic (BCC) metal after cold rolling (e.g., α, ξ, γ fibers) were minimized by the annealing/homogenization process. Moreover, grain structure was influenced by the fabrication route with elongated grains formed in the rolled sample and equiaxed grains found after annealing. Such features are relevant since the formation of microstructural features formed during fuel fabrication can impact fuel performance in reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of formability of Ca-added magnesium alloy sheets at low temperatures

The formability of sheets of the Ca-added magnesium alloy AZX311 was analyzed. The parameters affecting the sheet formability, such as the strain-hardening rate and the strain-rate sensitivity, did not seem to be higher in the alloy AZX311 at temperatures of room temperature (RT) and 200 °C. In addition, the critical stress for fracture at RT was lower in AZX311 than in AZ31. However, AZX311 exhibited higher stretchability and formability at low temperatures than AZ31. Electron back-scattered diffraction microscopy revealed that AZX311 had a weaker basal texture as well as broadened basal poles along the transverse direction. Polycrystal plasticity simulations confirmed that this weaker basal texture increases the activity of basal slip over thickness strain, resulting in the higher formability of AZX311. - Highlights: • A weak basal texture with broadening basal poles along the TD in AZX311 • Lower critical stress for fracture at RT in AZX311 than in AZ31 • Lower strain-hardening rates at low temperatures in the AZX311 than in the AZ31 • Higher formability at low temperatures in AZX311 because of the weak basal texture.

36 MATERIALS SCIENCE↗

Microstructural changes in an extruded Mg−Zn−Y alloy reinforced by quasicrystalline I-phase by small additions of calcium, manganese and cerium-rich mischmetal

The effects of calcium, manganese and cerium-rich mischmetal additions on the microstructure and texture of the extruded Mg−6Zn−1Y (wt.%) alloy have been investigated. The microstructure of the alloys consisted of a magnesium matrix embedding second phase particles aligned along the extrusion direction. The nature and volume fraction of the second phases depended on the alloying element. Thus, Ce-rich mischmetal promoted the formation of T-phase while calcium additions resulted in the formation of a ternary Mg−Zn−Ca compound. Only, manganese additions did not affect the existence of the I-phase present in the ternary alloy. The texture was measured and it was found that calcium addition has a significant effect weakening the extrusion texture. - Highlights: •In-situ HEXRD and DSC techniques are employed to identify phase transformations. •The existence of I-phase is not altered by manganese addition to Mg93Zn6Y1 (wt.%). •Calcium addition promotes Mg{sub 6}Zn{sub 3}Ca{sub 2} formation instead of I-phase. •Mischmetal addition induces the formation of coarse T-phase particles. •Texture depends on the nature of second phases and therefore of the extrusion pressure.

36 MATERIALS SCIENCE↗

Thermal stability of Cu-Cr-Zr alloy processed by equal-channel angular pressing

Thermal stability of a Cu-Cr-Zr alloy processed by equal-channel angular pressing up to16 passes was investigated using isochronal annealing ranging from 250 to 850 °C for 1 h. The microstructure, crystallographic texture and micro hardness of samples were characterized through electron back scatter diffraction and Vickers micro hardness measurements. The recrystallized grain size was stable between 250 °C and 500 °C then increased quickly. The achieved mean grain size, after 1, 4 and 16 ECAP passes, was around 5.5 μm. A discontinuous mode of recrystallization was found to occur and a Particle Simulated Nucleation mechanism was evidenced. The evolution of the high angle grain boundary fraction increased notably after annealing above 550 °C. The crystallographic texture after isochronal annealing was similar to that of ECAP simple shear, no change of the texture during annealing was observed but only slight intensity variations. Micro hardness of all Cu–Cr–Zr samples showed a hardening with two peaks at 400 and 500 °C associated with precipitation of Cu cluster and Cu{sub 5}Zr phase respectively, followed by a subsequent softening upon increasing the annealing temperature due to recrystallization. - Highlight: •The Cu-1Cr-0.1Zr alloy shows a very good thermal stability up to 550 °C after ECAP. •A discontinuous recrystallization was found to occur and PSN mechanism was evidenced. •The annealing texture was found weak and some new components appear. •Hardening is attributed to the Cr clustering followed by the Cu{sub 51}Zr{sub 14} precipitation. •Softening is a result of recrystallization and grain growth progressing.

36 MATERIALS SCIENCE↗

Quantitative characterization of material surface — Application to Ni + Mo electrolytic composite coatings

A new approach to numerical analysis of maps of material surface has been proposed and discussed in detail. It was concluded that the roughness factor RF and the root mean square roughness S{sub q} show a saturation effect with increasing size of the analysed maps what allows determining the optimal map dimension representative of the examined material. A quantitative method of determining predominant direction of the surface texture based on the power spectral density function is also proposed and discussed. The elaborated method was applied in surface analysis of Ni + Mo composite coatings. It was shown that co-deposition of molybdenum particles in nickel matrix leads to an increase in surface roughness. In addition, a decrease in size of the embedded Mo particles in Ni matrix causes an increase of both the surface roughness and the surface texture. It was also stated that the relation between the roughness factor and the double layer capacitance C{sub dl} of the studied coatings is linear and allows determining the double layer capacitance of the smooth nickel electrode. - Highlights: •Optimization of the procedure for the scanning of the material surface •Quantitative determination of the surface roughness and texture intensity •Proposition of the parameter describing privileged direction of the surface texture •Determination of the double layer capacitance of the smooth electrode.

36 MATERIALS SCIENCE↗

The plastic flow machining: A new SPD process for producing metal sheets with gradient structures

Highlights: • A new process named Plastic Flow Machining is presented to produce thin sheets by an extrusion operation from bulk material. • The produced sheets present ultra-fine grain structures, good mechanical properties and high formability. • A deformation gradient was found across the thickness of the sheet regarding plastic strain, microstructure and texture. - Abstract: A new severe plastic deformation process is presented – the plastic flow machining – an extrusion process during which a sheet is formed through a lateral opening of the die in a single operation. The sheet is heavily deformed presenting an ultra-fine grain structure. Experimental results are presented for commercially pure aluminum concerning microstructures, textures and mechanical properties. A gradient structure was found across the thickness of the sheet concerning plastic strain, grain size and texture. Only simple shear textures were seen. The material strength increased by a factor of three with significant ductility and with relatively high Lankford parameter.

36 MATERIALS SCIENCE↗

Electron backscatter diffraction helps direct calculation of magnetocrystalline anisotropy energy in API 5L steels

Highlights: • Experimental evidence of the capability of EBSD to accurately estimate MAE of API 5L steels. • MAE can be calculated directly from raw EBSD data for reduced sample sizes. • Number of grains sufficient to estimate MAE from EBSD is in the order of several hundreds. • The use of equivalent orientations increases drastically the accuracy of MAE estimations. • EBSD helps explain origin of the observed correlation between MAE and Barkhausen noise. - Abstract: This paper shows evidence of the capability of electron backscatter diffraction (EBSD) to accurately estimate the magnetocrystalline anisotropy energy (MAE) of API 5L steels. The crystallographic texture of five circular steel samples was characterized by X-ray global texture and EBSD microtexture measurements. The average MAE of each one of these samples was estimated from the set of individual grain orientations obtained from orientation maps measured by EBSD. The angular dependence of EBSD-derived MAE was compared with predictions made from X-ray texture and Barkhausen noise (BHN) measurements. The average MAE determined from the EBSD data is in good agreement with the predictions made from X-ray and BHN measurements for all the studied samples. This agreement can be explained by the fact that the number of grains used to predict the average MAE from the EBSD results was statistically sufficient to reproduce the MAE predicted by the other two methods. The EBSD measurement strategy for the accurate MAE estimation was established in terms of parameters such as the number of individual grain orientations to be measured, the sample's texture acuity and grain size, the use of equivalent orientations given by the statistical orthorhombic symmetry of the studied samples, and different measurement planes.

36 MATERIALS SCIENCE↗