Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPUTER MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Liquid Hydrogen Tank Chill and No-Vent Fill Prediction using Computational Fluid Dynamics

Cryogenic tank chill and fill is an important cryogenic fluid management technology that supports and enables many of NASA’s long-duration space missions. For no-vent fill, the receiver tank pressure remains below the supply tank pressure during the entire duration of the fill so that the tank does not require venting. This is especially advantageous for tank fill operations in low gravity where the position of the liquid is not always known and venting the tank may cause loss of propellant by venting liquid. In lieu of expensive tests conducted on-orbit, accurate computational models capable of predicting receiver tank pressure during cryogenic propellant tank fill may be used to reduce system and propellant mass as well as mission risk. However, these numerical models must be validated or anchored to test data. This study presents computational fluid dynamics (CFD) models with conjugate heat transfer that are used to predict a liquid hydrogen tank chill and no-vent fill ground test conducted at Lewis Research Center (now Glenn Research Center) in 1991. The specific test case chosen for model validation implemented an upward-facing jet near the bottom of a cylindrical 34-liter tank. CFD predictions are compared to experimental measurements of tank pressure, fill level, and wall temperature. The CFD results show reasonable agreement to the test data but overpredict the pressure collapse near the end of the fill despite the liquid jet penetrating the liquid-vapor interface.

Computational Fluid Dynamics↗
DOE OSTI2019

Melter Modeling over a Range of Scales to Support Vitrification at the WTP

Computational modeling is a powerful complement to laboratory experiments and testing of systems at various scales. When properly applied and validated, computational fluid dynamics (CFD) can provide information not readily obtainable by physical testing, especially in cases where the operating environment does not permit visual observation or the insertion of typical data acquisition instrumentation as in the case of waste glass vitrification. A series of CFD and heat transfer models over a range of scales are being developed to support melter operations at the Hanford Waste Treatment and Immobilization Plant. This paper provides a description of the models and the resulting information they provide that can be used to improve melter throughput, as well as aid in evaluating and resolving operating plant issues or upsets. This work is important for the WTP operation by providing a potential for model-predictive control of the melter operation. Increases in the rate of glass production and avoiding idling can significantly decrease the duration and cost of the vitrification campaign, potentially saving billions of dollars.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1985

Investigations into the triggered lightning response of the F106B thunderstorm research aircraft

An investigation has been conducted into the lightning characteristics of the NASA F106B thunderstorm research aircraft. The investigation includes analysis of measured data from the aircraft in the time and frequency domains. Linear and nonlinear computer modelling has also been performed. In addition, new computer tools have been developed, including a new enhanced nonlinear air breakdown model, and a subgrid model useful for analyzing fine details of the aircraft's geometry. Comparison of measured and calculated electromagnetic responses of the aircraft to a triggered lightning environment are presented.

Rudolph, Terence H.↗
NASA NTRS1982

The influence of turbulence models on computer-simulated aircraft landing

Three models of simulated atmospheric turbulence were used to determine their respective influence on a computer-simulated, DC-8 type, aircraft landing. Statistical results based on a sample of 20 simulated landings illustrate the influence of turbulence simulated by the different models. For the same spectrum function, a non-Gaussian turbulence model produces the higher degree of touchdown variability. When different spectrum functions are used the von Karman model induces a smaller standard deviation in position error than the Dryden model. The turbulence energy contained by the higher frequency fluctuation has little effect on the landing position.

Frost, W.↗
DOE OSTI2023

Discerning Deception: An Empirically-Driven Agent-Based Model of Expert Evaluation of Scientific Content

Both human subject experiments and computational, modeling and simulations have been used to study detection of deception. This work aims to combine these two methods by integrating empirically-derived information (from human subject experiments) into agent-based models to generate novel insights into the complex problems of detection of disinformation content. Computational experiments are used to simulate across multiple scenarios for evaluation and decision-making regarding the validity of potentially deceptive scientific documents. Factors influencing the human agent behaviors in the model were identified through a human subject experiment that was conducted to evaluate and characterize decision making related to disinformation discernment. Correlation and regression analyses were used to translate insights from the human subjects experiment to inform the parameterization of agent features and scenario development. Three scenarios were evaluated with the agent-based models to help evaluate the replicability of the simulations (validation analysis) and assess the influence of human agent and document features (sensitivity analyses). A replication of the human participant experiment demonstrated that the agent-based simulations compare favorably to empirical findings. The agent-based modeling was then used to conduct sensitivity analysis on the accuracy of deception detection as a function of document proportions and human agent features. Results indicate that precision values are adversely impacted when the proportion of deceptive documents is lower in the overall sample, whereas recall values are more sensitive to changes in human agent features. These findings indicate important nuances in accuracy evaluations that should be further considered (including consideration of potential alternate metrics) in future agent-based models of disinformation. Additional areas for future exploration include extension of simulations to consider other ways to align the agent-based model design with psychological theory and inclusion of agent-agent interactions, especially as it pertains to sharing of scientific information within an organizational context.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2017

Extreme Scale Unstructured Adaptive CFD: From Multiphase Flow to Aerodynamic Flow Control

Understanding the flow of fluid, either liquid or gas, through and around solid bodies has challenged man since the dawn of scientific inquiry. Many of the great minds of science and math have progressively built up a hierarchy of fluid models. This report is concerned with the computational modeling of turbulent flow around aerodynamic bodies such as planes and wind turbines. In this case, viscous effects near the solid bodies create very thin boundary layers that yield highly anisotropic (gradients normal to the surface may be 10^6 times larger than gradients along the surface) solutions to the governing non-linear partial differential equations (PDE); the Navier-Stokes equations. Furthermore, turbulent flows develop extremely broad ranges of length and time scales.This disparity motivates the use of discretization methods capable of employing adaptivity and implicit time integration. The combination of these features (non-linear, anisotropy, adaptivity, andimplicit) dramatically raise the complexity of the discretization, posing large challenges to efficient scalable parallel implementation. However, through careful design, the more complex algorithms can provide great reductions in computational cost relative to simpler methods (e.g., Cartesian grids with explicit time integration) that are easier to mate efficiently to hardware. In this report, we not only describe our approach but we also address the fact that while complex algorithms may never be as efficient flop-for-flop as simple methods, in the important measure of science-per-core-hour, they can still win big by making complex features like adaptivity and implicit methods as efficient and scalable as possible.

42 ENGINEERING↗
DOE OSTI2021

Integrating Systems and Synthetic Biology to Understand and Engineer Microbiomes

Microbiomes are complex and ubiquitous networks of microorganisms whose seemingly limitless chemical transformations could be harnessed to benefit agriculture, medicine, and biotechnology. Here, the spatial and temporal changes in microbiome composition and function are influenced by a multitude of molecular and ecological factors. This complexity yields both versatility and challenges in designing synthetic microbiomes and perturbing natural microbiomes in controlled, predictable ways. In this review, we describe factors that give rise to emergent spatial and temporal microbiome properties and the meta-omics and computational modeling tools that can be used to understand microbiomes at the cellular and system levels. We also describe strategies for designing and engineering microbiomes to enhance or build novel functions. Throughout the review,we discuss key knowledge and technology gaps for elucidating the networks and deciphering key control points for microbiome engineering, and highlight examples where multiple omics and modeling approaches can be integrated to address these gaps.

42 ENGINEERING↗
NASA NTRS1996

Experimental and Computational Aerothermodynamics of a Mars Entry Vehicle

An aerothermodynamic database has been generated through both experimental testing and computational fluid dynamics simulations for a 70 deg sphere-cone configuration based on the NASA Mars Pathfinder entry vehicle. The aerothermodynamics of several related parametric configurations were also investigated. Experimental heat-transfer data were obtained at hypersonic test conditions in both a perfect gas air wind tunnel and in a hypervelocity, high-enthalpy expansion tube in which both air and carbon dioxide were employed as test gases. In these facilities, measurements were made with thin-film temperature-resistance gages on both the entry vehicle models and on the support stings of the models. Computational results for freestream conditions equivalent to those of the test facilities were generated using an axisymmetric/2D laminar Navier-Stokes solver with both perfect-gas and nonequilibrium thermochemical models. Forebody computational and experimental heating distributions agreed to within the experimental uncertainty for both the perfect-gas and high-enthalpy test conditions. In the wake, quantitative differences between experimental and computational heating distributions for the perfect-gas conditions indicated transition of the free shear layer near the reattachment point on the sting. For the high enthalpy cases, agreement to within, or slightly greater than, the experimental uncertainty was achieved in the wake except within the recirculation region, where further grid resolution appeared to be required. Comparisons between the perfect-gas and high-enthalpy results indicated that the wake remained laminar at the high-enthalpy test conditions, for which the Reynolds number was significantly lower than that of the perfect-gas conditions.

Hollis, Brian R.↗
DOE OSTI2018

Direct observation of dislocation structure evolution in SRF cavity niobium using electron channeling contrast imaging

Two major goals of superconducting radio frequency cavity research and development are achieving higher accelerating gradient and gaining the highest quality factor, a measure of efficiency. However, the consistent improvement of these performance metrics is restricted by many factors, one of which is microstructural defects, such as dislocation substructures within the material. In this work, dislocation evolution is compared in four samples extracted from a 2.8 mm thick large-grain niobium slice, with tensile axes chosen to generate specific dislocation structures during subsequent deformation. The four samples are (1) as-extracted, (2) extracted and annealed, (3) extracted and then deformed to 40% tensile strain, and (4) extracted, annealed at 800 °C 2 h, and then deformed to 40% strain. Electron channeling contrast imaging was performed on all samples to characterize initial dislocation density and dislocation structure evolution due to annealing and deformation, and related to the mechanical behavior observed in stress-strain curves. A fundamental understanding of dislocation evolution in niobium is necessary to develop computational models to simulate cavity forming, which could enable new processing methods for cavity fabrication to be identified that could lead to improved performance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Chapter 24: Two- and Three-Dimensional Electronic Modeling of Thin-Film Solar Cells

Modeling can provide physical insight to device operation, help distinguish important material properties from unimportant properties, predict trends, and help interpret experimental data. Numerical modeling is also useful to simulate different electro-optical experiments, in the presence of grain boundaries (GBs) and nonplanar junctions and geometries, and to help interpret data obtained in such experiments. This chapter presents methods for effective multidimensional modeling. The first step in creating a computational model is defining and providing discretization of a 2D area or a 3D volume. Two main approaches to the discretization have been used for studying solar cells: equivalent-circuit modeling and solving semiconductor equations. The chapter gives some examples of problems that were addressed with 2D or 3D modeling and the knowledge that was gained through them. Multidimensional modeling including GBs and other material variations is necessary to explain the device physics and experimental results present in diverse thin-film technologies.

14 SOLAR ENERGY↗
DOE OSTI2025

Towards robust surrogate models: Benchmarking machine learning approaches to expediting phase field simulations of brittle fracture

Data-driven approaches have the potential to make modeling complex, nonlinear physical phenomena significantly more computationally tractable. For example, computational modeling of fracture is a core challenge where machine learning techniques have the potential to provide a much needed speedup that would enable progress in areas such as multi-scale modeling and uncertainty quantification. Currently, phase field modeling (PFM) of fracture is one such approach that offers a convenient variational formulation to model crack nucleation, branching and propagation. To date, machine learning techniques have shown promise in approximating PFM simulations. While standard fracture benchmarks represent realistic scenarios frequently observed in practice, they typically do not provide sufficiently challenging tests for data-driven methods. Here, to address this gap, we introduce a challenging dataset based on PFM simulations designed to benchmark and advance ML methods for fracture modeling. This dataset includes three energy decomposition methods, two boundary conditions, and 1000 random initial crack configurations for a total of 6000 simulations. Each sample contains 100 time steps capturing the temporal evolution of the crack field. Alongside this dataset, we also implement and evaluate Physics Informed Neural Networks (PINN), Fourier Neural Operators (FNO), and UNet models as baselines, and explore the impact of ensembling strategies on prediction accuracy. With this combination of our dataset and baseline models drawn from the literature we aim to provide a standardized and challenging benchmark for evaluating machine learning approaches to solid mechanics. Our results highlight both the promise and limitations of popular current models, and demonstrate the utility of this dataset as a testbed for advancing machine learning in fracture mechanics research.

Benchmark dataset↗
DOE OSTI2022

Perspectives on the integration between first-principles and data-driven modeling

Efficiently embedding and/or integrating mechanistic information with data-driven models is essential if it is desired to simultaneously take advantage of both engineering principles and data-science. Further the opportunity for hybridization occurs in many scenarios, such as the development of a faster model of an accurate high-fidelity computer model; the correction of a mechanistic model that does not fully-capture the physical phenomena of the system; or the integration of a data-driven component approximating an unknown correlation within a mechanistic model. At the same time, different techniques have been proposed and applied in different literatures to achieve this hybridization, such as hybrid modeling, physics-informed Machine Learning (ML) and model calibration. In this paper we review the methods, challenges, applications and algorithms of these three research areas and discuss them in the context of the different hybridization scenarios. Moreover, we provide a comprehensive comparison of the hybridization techniques with respect to their differences and similarities, as well as advantages and limitations and future perspectives. Finally, we apply and illustrate hybrid modeling, physics-informed ML and model calibration via a chemical reactor case study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Alternative CAES Technology Using Depleted Unconventional Gas Wells and Subsurface Thermal Energy Storage (GeoCAES)

This project assessed the technical viability of a process called GeoCAES. The process stores electrical energy by injecting natural gas into shale gas formations using a compressor, storing it, and producing it through an expander to generate electricity. This data submission includes the models of temperature and pressure changes in the wellbore, surface plant equipment (compressor and expander), and the code used in CMG GEM reservoir modeling software to simulate injection and production. Note - the wellbore and surface plant equipment models use the REFPROP Excel Add-in from NIST (linked in submission) to calculate natural gas properties. Note - the reservoir model code requires a license for the Computer Modeling Group (CMG) GEM reservoir modeling software (linked in submission) to run it.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Image Analysis: Comparison Metrics

Despite an increased reliance on computational modeling in engineering and physics, graphically comparing computational and experimental results has often been qualitative, via a so-called ‘viewgraph norm’. Image recognition, computer vision and artificial intelligence (AI) are fields of study in themselves and rapidly progressing, but relying on AI to grade image similarity evokes a notion of asking for an expert judgement, which could be seen as an artificial version of the viewgraph norm. It is, therefore, desirable to use simpler metrics which are more tractable and unambiguous, even though they may not be as ‘intelligent.’ In this document, a few metrics are studied by systematically altering an image and their implications are analyzed

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2016

A MULTIPLE SCATTERING POLARIZED RADIATIVE TRANSFER MODEL: APPLICATION TO HD 189733b

We present a multiple scattering vector radiative transfer model that produces disk integrated, full phase polarized light curves for reflected light from an exoplanetary atmosphere. We validate our model against results from published analytical and computational models and discuss a small number of cases relevant to the existing and possible near-future observations of the exoplanet HD 189733b. HD 189733b is arguably the most well observed exoplanet to date and the only exoplanet to be observed in polarized light, yet it is debated if the planet’s atmosphere is cloudy or clear. We model reflected light from clear atmospheres with Rayleigh scattering, and cloudy or hazy atmospheres with Mie and fractal aggregate particles. We show that clear and cloudy atmospheres have large differences in polarized light as compared to simple flux measurements, though existing observations are insufficient to make this distinction. Futhermore, we show that atmospheres that are spatially inhomogeneous, such as being partially covered by clouds or hazes, exhibit larger contrasts in polarized light when compared to clear atmospheres. This effect can potentially be used to identify patchy clouds in exoplanets. Given a set of full phase polarimetric measurements, this model can constrain the geometric albedo, properties of scattering particles in the atmosphere, and the longitude of the ascending node of the orbit. The model is used to interpret new polarimetric observations of HD 189733b in a companion paper.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1975

Composition of the Martian dust as derived by infrared spectroscopy from Mariner 9

The Martian dust spectra obtained by the infrared interferometer spectrometer (Iris) experiment on Mariner 9 have been compared with modeling computations for various minerals and rocks. The model used was based upon a recently developed theory of absorption and scattering by particulate materials. The results indicate that the composition of Martian dust is biased toward silicate structures which involve a high degree of silicate oxygen sharing. A feldspar-rich dust of approximately 1-micron particle size appears to be the best candidate, although sheet-structure silicates cannot be ruled out.

Aronson, J. R.↗
NASA NTRS1980

A new predictive model for determining solar wind-terrestrial planet interactions

A computational model has been developed for the determination of the gasdynamic and magnetic field properties of the solar wind flow around a magnetic planet, such as the earth, or a nonmagnetic planet, such as Venus. The procedures are based on an established single-fluid, steady, dissipationless, magnetogasdynamic model and are appropriate for the calculation of axisymmetric, supersonic, super-Alfvenic solar wind flow past a planetary magneto/ionosphere. Sample results are reported for a variety of solar wind and planetary conditions. Some of these are new applications; others are included to show that the new procedures produce the same results as previous procedures when applied to the same conditions. The new methods are completely automated and much more efficient and versatile than those employed heretofore.

Spreiter, J. R.↗