Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Thermal Conductivity and Seebeck Coefficients of Icosahedral Boron Arsenide Films on Silicon Carbide

The thermal conductivity of icosahedral boron arsenide (B{sub 12}As{sub 2}) films grown on (0001) 6H-SiC substrates by chemical vapor deposition was studied by the 3{omega} technique. The room temperature thermal conductivity decreased from 27.0 to 15.3 W/m K as the growth temperature was decreased from 1450 to 1275 C. This is mainly attributed to the differences in the impurity concentration and microstructure, determined from secondary ion mass spectrometry and high resolution transmission electron microscopy, respectively. Callaway's theory was applied to calculate the temperature-dependent thermal conductivity, and the results are in good agreement with the experimental data. Seebeck coefficients were determined as 107 {micro}V/K and 136 {micro}V/K for samples grown at 1350 C with AsH{sub 3}/B{sub 2}H{sub 6} flow ratio equals to 1:1 and 3:5, respectively.

36 MATERIALS SCIENCE↗

Characterization of 100 mm Diameter 4H-Silicon Carbide CrystalsWith Extremely Low Basal Plane Dislocation Density

Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.

36 MATERIALS SCIENCE↗

Characterization of 100 mm Diameter 4H-Silicon Carbide CrystalsWith Extremely Low Basal Plane Dislocation Density

Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.

36 MATERIALS SCIENCE↗

88 kilowatt automotive inverter with new 900 Volt silicon carbide MOSFET technology

This final report is on the design and experimental verification of a 200 kVA traction inverter using three 900 V, 2.5 mΩ, SiC MOSFET-based half-bridge power modules comprising the power stage. Each dual power module contains four 900 V, 10 mΩ SiC MOSFETs per switch position and uses synchronous conduction to achieve high average and peak efficiencies over its entire operating region to meet the demands of hybrid, plug-in hybrid, and extended-range electrified vehicle architectures. Significant performance improvement, via conduction, switching, and reverse-recovery loss metrics, from this SiC MOSFET-based inverter—especially at light load conditions—will be discussed.

30 DIRECT ENERGY CONVERSION↗

Radiation Tolerance of Silicon Carbide Joints at LWR Relevant Temperature

The development of reliable joints in reactor service conditions is a critical requirement for SiC based accident tolerant fuels and core structures for light water reactor (LWR) applications. The effects of neutron irradiation on the mechanical properties is an important consideration under normal operation. Though various SiC joints retained the strength following neutron irradiation at ∼500 and ∼800 deg. C to ∼3 dpa, the irradiation tolerance of the joints at the LWR relevant temperature is still an unknown. This study presents the strengths of the candidate SiC joints following irradiation at ∼300 deg. C. The bonding strength was investigated using torsional shear testing which was developed for miniature irradiation specimens in previous work. Torsional shear strengths of various SiC joints were evaluated following irradiation at 270-310 deg. C to 8.7 dpa. Strength degradation by the irradiation likely occurred in the Mo diffusion bond. No obvious strength degradation was found in the MAX phase and hybrid polymer/CVD joints. The irradiation caused large deviation of the strength of Ti diffusion bond, TEP slurry and tape joints. The cause of this deviation will be investigated based on microstructural analysis in future work. (authors)

36 MATERIALS SCIENCE↗

Silicon Carbide Passive Temperature Sensors at INL

Discuss the SiC passive thermometry methods currently performed at INL and ORNL, decide on best path forward for establishing an ASTM Standard for processing SiC temperature monitors, and expand this ASTM benchmarking efforts to international collaborators (Netherlands, Canada, and Poland).

36 MATERIALS SCIENCE↗