Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Compression-ignition engine performance with undoped and doped fuel oils and alcohol mixtures

Several fuel oils, doped fuel oils, and mixtures of alcohol and fuel oil were tested in a high-speed, single-cylinder, compression-ignition engine to determine power output, fuel consumption, and ignition and combustion characteristics. Fuel oils or doped fuel oils of high octane number had shorter ignition lags, lower rates of pressure rise, and gave smoother engine operation than fuel oils or doped fuel oils of low octane number. Higher engine rotative speeds and boost pressures resulted in smoother engine operation and permitted the use of fuel oils of relatively low octane number. Although the addition of a dope to a fuel oil decreased the ignition lag and the rate of pressure rise, the ensuing rate of combustion was somewhat slower than for the undoped fuel oil so that the effectiveness of combustion was practically unchanged. Alcohol used as an auxiliary fuel, either as a mixture or by separate injection, increased the rates of pressure rise and induced roughness. In general, the power output decreased as the proportion of alcohol increased and, below maximum power, varied with the heating value of the total fuel charge.

Moore, Charles S↗

The Effect of Driving Intensity and Incomplete Charging on the Fuel Economy of a Hymotion Prius PHEV

On-road testing was conducted on a Hymotion Prius plug-in hybrid electric vehicle (PHEV) at the Electric Transportation Engineering Corporation in Phoenix, Arizona. The tests were comprised of on-road urban and highway driving during charge-depleting and charge-sustaining operation. Determining real-world effectiveness of PHEVs at reducing petroleum consumption in real world driving was the main focus of the study. Throughout testing, several factors that affect fuel consumption of PHEVs were identified. This report discusses two of these factors: driving intensity (i.e., driving aggressiveness) and battery charging completeness. These two factors are unrelated, yet both significantly impact the vehicle’s fuel economy. Driving intensity was shown to decrease fuel economy by up to half. Charging completeness, which was affected by human factors and ambient temperature conditions, also showed to have great impact on fuel economy for the Hymotion Prius. These tests were performed for the U.S. Department of Energy’s Advanced Vehicle Testing Activity. The Advanced Vehicle Testing Activity, part of the U.S. Department of Energy’s Vehicle Technology Program, is conducted by the Idaho National Laboratory and the Electric Transportation Engineering Corporation.

33 ADVANCED PROPULSION SYSTEMS↗

Fabrication of capsule assemblies, phase 3

Thirteen capsule assemblies were fabricated for evaluation of fuel pin design concepts for a fast spectrum lithium cooled compact space power reactor. These instrumented assemblies were designed for real time test of prototype fuel pins. Uranium mononitride fuel pins were encased in AISI 304L stainless steel capsules. Fabrication procedures were fully qualified by process development and assembly qualification tests. Instrumentation reliability was achieved utilizing specially processed and closely controlled thermocouple hot zone fabrication and by thermal screening tests. Overall capsule reliability was achieved with an all electron beam welded assembly.

Keeton, A. R.↗

Aluminum Clad Spent Nuclear Fuel Task 1: Oxyhydroxide Layer Behavior and Chemistry Experimental Test Plan

This document presents the test plan for Task 1 of the Aluminum Clad Spent Nuclear Fuel Long Term Dry Storage Technical Issues Action Plan, which covers aluminum clad spent nuclear fuel (ASNF) fuel that is currently or may in the future be held in dry storage for an extended period. The objectives of the Task 1 test plan are to: 1. Understand how ASNF performs over extended dry storage periods. 2. Understand mechanisms that could alter aluminum hydroxide/oxyhydroxide layers during extended storage. 3. Characterize thickness and growth rates of oxyhydroxide layers based on fuel history and provide anticipated H2 gas generation rates based on chemical corrosion. 4. Characterize materials properties for oxides present on ASNF. 5. Interface with canister modeling activity to deliver degradation rates for package performance for both sealed and vented configurations. 6. Understand implications of higher temperature drying (250°C) on stability in dry storage. This test plan lays out the technical activities that will be performed to achieve the test objectives described above. Experiments will be performed at Idaho National Laboratory in-town facilities. Specimens for testing will include those supplied by Savannah River National Laboratory. Activities will include both experiments and modeling and will coordinate with other tasks within the project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Altitude engine test of a turbofan exhaust gas mixer to conserve fuel

A comparison of the specific fuel consumption was made with and without an internal mixer installed in a low bypass ratio, confluent flow turbofan engine. Tests were conducted at several Mach numbers and altitudes for core to fan stream total temperature ratios of 2.0 and 2.5 and mixing lengths of L/D = 0.95 and 1.74. For these test conditions, the specific fuel consumption improvement varied from 2.5 to 4.0 percent.

Cullom, R. R.↗

TREAT LEU Conversion Analyses Performed 2016-2018

TREAT is an experimental nuclear reactor designed to produce high neutron flux transients for the testing of reactor fuels and other materials. After more than 20 years of non-operational standby, TREAT has been restarted under the U.S. Department of Energy’s Resumption of Transient Testing Program. The conversion of TREAT from its current highly enriched uranium fuel to a low enriched uranium fuel is being pursued in keeping with the mission of the Department of Energy National Nuclear Security Administration’s Material Management and Minimization Reactor Conversion Program. This report documents additional analyses performed over the timeframe of 2016 to early 2018 to evaluate the LEU Conceptual Design for the TREAT reactor, following the initial design studies documented in the 2016 Conceptual Design Report. The analyses documented in this report include neutronic and thermal hydraulic sensitivity studies to evaluate the effect of key design parameters on predicted core behaviors, as well as a simple investigation into the effect of fuel thermal expansion.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

AFIP-1 Irradiation Summary Report

The Advanced Test Reactor (ATR) Full size plate In center flux trap Position (AFIP) experiment AFIP-1 was designed to demonstrate the performance of second-generation dispersion fuels at a prototypic scale with a length of 21.5 inches (54.6 cm), width of 2.25 inches (5.75 cm) and a thickness of 0.050 inch (0.13 cm). The experiment was fabricated using commercially standard practices at BWX Technology, Inc. (BWXT). The U-7Mo fuel particles were supplied by the Korean Atomic Energy Research Institute (KAERI) using equipment intended for commercial supply. Two fuel plates were tested that incorporated two different matrix compositions, Al-2Si and Al-4043.1 The following report summarizes the life of the AFIP-1 experiment through end of irradiation, including a brief description of the safety analysis, as-run neutronic analysis results, hydraulic testing results, and thermal analysis results

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Flame Tube Testing of a GEA TAPS Injector: Effects of Fuel Staging on Combustor Fuel Spray Patterns, Flow Structure, and Speciation

This paper presents results in which we compare fuel staging and its effect on fuel spray pattern, velocity and speciation during combustion for several inlet conditions using a GE TAPS injector configuration. Planar laser-induced fluorescence (PLIF), particle image velocimetry (PIV) and phase Doppler interferometry (PDI) were used to investigate spray patterns and velocity. The 2D PIV provides slices in the flow of axial-vertical or axial horizontal velocity components. With 3D PDI, we obtained 3 components of velocity, and fuel drop sizes. Chemiluminescence imaging and spontaneous Raman scattering (SRS) were used to investigate flame structure, species location and relative species concentration. Phase Doppler and PIV data were acquired using scatter from fuel droplets; therefore, those data were obtained only at the pilot-only test points. Raman measurements were acquired only at 10/90 split points to avoid droplets.

GE TAPS↗

Cold flow testing of the Space Shuttle Main Engine high pressure fuel turbine model

In order to experimentally determine the performance of the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) turbine, a 'cold' air flow turbine test program was established at NASA's Marshall Space Flight Center. As part of this test program, a baseline test of Rocketdyne's HPFTP turbine has been completed. The turbine performance and turbine diagnostics such as airfoil surface static pressure distributions, static pressure drops through the turbine, and exit swirl angles were investigated at the turbine design point, over its operating range, and at extreme off-design points. The data was compared to pretest predictions with good results. The test data has been used to improve meanline prediction codes and is now being used to validate various three-dimensional codes. The data will also be scaled to engine conditions and used to improve the SSME steady-state performance model.

Hudson, Susan T.↗

STAT7 v2.0 Verification and Validation Report

This report documents the software testing which has been performed for STAT7 Version 2.0 (hereafter STAT7 v2.0), a code for the statistical propagation of uncertainties in steady-state thermal hydraulics (TH) analysis of plate-fueled research and test reactors. The key capabilities addressed in this testing were selected based on the use of the software for analysis work supporting the conversion to low-enriched uranium fuel of U.S. High-Performance Research Reactors (USHPRR) such as the Massachusetts Institute of Technology Research Reactor (MITR-II). This testing scope includes comparison of the code’s statistical processing capabilities using statistical tests, comparison of coolant property evaluations to NIST data tables, and systematic comparison of key TH solver capabilities to the results of hand calculations and to predictions from PLTEMP/ANL Version 4.4. The

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Micro-tensile testing of the bond line in hot isostatic pressed aluminum

Considerable effort is being devoted to development and regulatory qualification of low enriched fuels for research and test reactors by many agencies worldwide. One promising fuel configuration being examined for United States higher power research and test reactors (USHPRRs) are plate-type fuels composed of a metallic uranium-molybdenum foil clad in an aluminum alloy. The two pieces of aluminum alloy cladding are bonded using a hot isostatic pressing method. The mechanical properties of the resulting bond line in the aluminum alloy cladding will vary by the HIP'ing parameters, requiring a need to characterize the bond line. Small scale mechanical testing can provide a path for evaluating the mechanical properties and deformation behavior of the bond line both prior to and following irradiation. Here, in this research, room temperature micro-tensile specimens of non-irradiated and irradiated samples containing an Al alloy (AA 6061) bond line were tested to evaluate its strength and deformation behavior. Observations indicated that the strain rate did not affect the deformation behavior or strength and most of the micro-tensile specimens failed in a ductile mode in grains around the bond line. There was no indication that the microstructural features from the bond line affected the mechanical properties of the micro-tensile specimens. An initial examination was performed on irradiated material but further systematic studies of the effects of irradiation can be performed in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

STAT7 v1.2 Verification and Validation Report

This report documents the software testing which has been performed for the STAT7 Version 1.2 (hereafter STAT7 v1.2) software, a code for the statistical propagation of uncertainties in steady-state thermal hydraulics (TH) analysis of plate-fueled research and test reactors. The key capabilities addressed in this testing were selected based on the use of the software for analysis work supporting the conversion to low-enriched uranium fuel of U.S. High-Performance Research Reactors (USHPRR) such as the Massachusetts Institute of Technology Research Reactor (MITR-II). This testing scope includes comparison of the code’s statistical processing capabilities using statistical tests, comparison of coolant property evaluations to NIST data tables, and systematic comparison of key TH solver capabilities to the results of hand calculations and to predictions from PLTEMP/ANL Version 4.4. The good agreement achieved in this testing campaign, within the acceptance criteria of a 1% relative difference, also demonstrates that these capabilities have been implemented in STAT7 v1.2 correctly.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

BISON As-run AGR-3/4 Irradiation Test Predictions

BISON, a nuclear fuel performance application built using the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element library, was used to model the Advanced Gas Reactor (AGR)-3/4 irradiation test using as-run physics and thermal hydraulics data. The AGR-3/4 test consists of the combined third and fourth planned irradiations of the AGR Fuel Development and Qualification Program. The AGR-3/4 test train consists of twelve separate and independently controlled and monitored capsules. Each capsule contains four compacts filled with both uranium oxycarbide (UCO) unaltered “driver” fuel particles and UCO designed-to-fail (DTF) fuel particles. The DTF fraction was specified to be 1×10-2. This report documents the calculations performed to predict the failure probability of tristructural isotropic (TRISO) coated driver fuel particles during the AGR-3/4 experiment on a single compact. This report will demonstrate the capabilities of BISON to model the complex AGR-3/4 irradiation test and identify further development needed to capture the fuel particle failure probability and source term on every compact for further comparison from post-irradiation examination (PIE) data. The calculations include the modeling of the AGR-3/4 irradiation that occurred from December 2011 to April 2014 in the Advanced Test Reactor (ATR) over a total of 10 ATR cycles including seven normal cycles, one low power cycle, one unplanned outage cycle, and one Power Axial Locator Mechanism (PALM) cycle.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nuclear Cryogenic Propulsion Stage Fuel Design and Fabrication

Nuclear Cryogenic Propulsion Stage (NCPS) is a game changing technology for space exploration. Goal of assessing the affordability and viability of an NCPS includes thses overall tasks: (1) Pre-conceptual design of the NCPS and architecture integration (2) NCPS Fuel Design and Testing (3) Nuclear Thermal Rocket Element Environmental Simulator (NTREES) (4) Affordable NCPS Development and Qualification Strategy (5) Second Generation NCPS Concepts. There is a critical need for fuels development. Fuel task objectives are to demonstrate capabilities and critical technologies using full scale element fabrication and testing.

Hickman, Robert↗

Nuclear Cryogenic Propulsion Stage Fuel Design and Fabrication

Nuclear Cryogenic Propulsion Stage (NCPS) is a game changing technology for space exploration. Goal of assessing the affordability and viability of an NCPS includes these overall tasks: (1) Pre-conceptual design of the NCPS and architecture integration (2) NCPS Fuel Design and Testing (3) Nuclear Thermal Rocket Element Environmental Simulator (NTREES) (4) Affordable NCPS Development and Qualification Strategy (5) Second Generation NCPS Concepts. There is a critical need for fuels development. Fuel task objectives are to demonstrate capabilities and critical technologies using full scale element fabrication and testing.

Hickman, Robert↗

Out-of-core Evaluations of Uranium Nitride-fueled Converters

Two uranium nitride fueled converters were tested parametrically for their initial characterization and are currently being life-tested out of core. Test method being employed for the parametric and the diagnostic measurements during the life tests, and test results are presented. One converter with a rhenium emitter had an initial output power density of 6.9 W/ sq cm at the black body emitter temperature of 1900 K. The power density remained unchanged for the first 1000 hr of life test but degraded nearly 50% percent during the following 1000 hr. Electrode work function measurements indicated that the uranium fuel was diffusing out of the emitter clad of 0.635 mm. The other converter with a tungsten emitter had an initial output power density of 2.2 W/ sq cm at 1900 K with a power density of 3.9 W/sq cm at 4300 h. The power density suddenly degraded within 20 hr to practically zero output at 4735 hr.

Shimada, K.↗

Thermal-barrier coatings for utility gas turbines

The potential of thermal barrier coatings for use in utility gas turbines was assessed. Pressurized passage and ambient pressure doped fuel burner rig tests revealed that thermal barrier coatings are not resistant to dirty combustion environments. However, present thermal barrier coatings, such as duplex partially stabilized zirconia and duplex Ca2SiO4 have ample resistance to the thermo-mechanical stress and temperature levels anticipated for heavy duty gas turbines firing clean fuel as revealed by clean fuel pressurized passage and ambient pressure burner rig tests. Thus, it is appropriate to evaluate such coatings on blades, vanes and combustors in the field. However, such field tests should be backed up with adequate effort in the areas of coating application technology and design analysis so that the field tests yield unequivocal results.

Levine, S. R.↗