Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Preparation of silicon carbide-silicon nitride fibers by the pyrolysis of polycarbosilazane precursors - A review

The development of silicon carbide-silicon nitride fibers (SiC-Si3N4) by the pyrolysis of polycarbosilazane precursors is reviewed. Precursor resin, which was prepared by heating tris(N-methylamino)methylsilane or tris(N-methylamino)phenylsilane to about 520 C, was drawn into fibers from the melt and then made unmeltable by humidity conditioning at 100 C and 95 percent relative humidity. The humidity treated precursor fibers were pyrolyzed to ceramic fibers with good mechanical properties and electrical resistivity. For example, SiC-Si3N4 fibers derived from tris(N-methylamino)methylsilane had a tensile rupture modulus of 29 million psi and electrical resistivity of 6.9 x ten to the 8th power omega-cm, which is ten to the twelfth power times greater than that obtained for graphite fibers.

Penn, B. G.↗

Characterization of sorbent properties of soil organic matter and carbonaceous geosorbents using n-alkanes and cycloalkanes as molecular probes

Nonspecific interactions and modes (i.e., adsorption vs absorption) of sorption by noncondensed, amorphous organic phases (here termed organic matter; OM) in soils and by rigid, aromatic, and condensed phases (termed carbonaceous geosorbents; CGs) were investigated using n-alkanes and cycloalkanes as molecular probes. Sorption isotherms of and cyclooctane from water for seven CGs (charcoal, lignite coke, activated carbon, graphite, partially oxidized graphite, diesel soot, bituminous coal), four sorbents with a predominance of OM (lignite, peat, two sapric soils), and two soils containing OM and high amounts of CGs were measured in batch systems. The peat and the sapric soils showed extensively linear sorption, while the CGs exhibited highly nonlinear and strong (K{sub oc} values being up to 105 times those for the OM-rich materials at low concentrations) sorption for the alkanes studied, showing that enhanced sorption by CGs can occur to completely apolar sorbates that do not undergo any specific interaction. The n-octane-to-cyclooctane sorption coefficient ratios for adsorption to CGs were {ge}1, being distinctly different from those for absorption to the OM-rich materials. The measured sorption isotherms and the CG compositions in the soils determined by quantitative petrography analysis suggest, however, that CGs occurring in soils may be far less effective sorbents than the reference CGs used in the sorption experiments at least for nonspecifically interacting sorbates, probably because of competitive sorption and/or pore blocking by natural OM. The presented approaches and results offer a basis for interpreting sorption data for other organic compounds, as nonspecific interactions and sorption modes are relevant for any compound. 47 refs., 4 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Assessing photocatalytic power of g-C{sub 3}N{sub 4} for solar fuel production: A first-principles study involving quasi-particle theory and dispersive forces

First-principles quasi-particle theory has been employed to assess catalytic power of graphitic carbon nitride, g-C{sub 3}N{sub 4}, for solar fuel production. A comparative study between g-h-triazine and g-h-heptazine has been carried out taking also into account van der Waals dispersive forces. The band edge potentials have been calculated using a recently developed approach where quasi-particle effects are taken into account through the GW approximation. First, it was found that the description of ground state properties such as cohesive and surface formation energies requires the proper treatment of dispersive interaction. Furthermore, through the analysis of calculated band-edge potentials, it is shown that g-h-triazine has high reductive power reaching the potential to reduce CO{sub 2} to formic acid, coplanar g-h-heptazine displays the highest thermodynamics force toward H{sub 2}O/O{sub 2} oxidation reaction, and corrugated g-h-heptazine exhibits a good capacity for both reactions. This rigorous theoretical study shows a route to further improve the catalytic performance of g-C{sub 3}N{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application of a gripping system to test a uniaxial graphite fiber reinforced composite /PMR 15/Celion 6000/ in tension at 316 C

A gripping system has been developed to test uniaxial, 0 deg orientation PMR 15/Celion 6000 composites at elevated temperatures. The method involves compression of grit-blasted laminate between grit-blasted metal to give a non-slipping interface for load transfer. Tensile testing at both 316 C and room temperature indicated that deformation was elastic to fracture and that the variation in tensile properties for one laminate is the same as that for several panels. In addition, the tensile properties for uniaxial PMR 15/Celion 6000 are identical at 316 C and room temperature. For nominally 51 volume percent fiber, the elastic modulus is 119.6 GPa, the fracture stress is 1370 MPa, and the strain to fracture is about 1.15 percent. In addition, data are presented which indicate that the gripping system can be used for long term, elevated temperature testing of composite materials.

Whittenberger, J. D.↗

Influence of Austempering Temperature and Time on the Microstructure and Mechanical Properties of Ductile Iron Weldment Using Developed Coated Electrode

Sound welded joints of ductile iron were first made by developing coated electrodes as well as weld procedure. The weldments were then austenitized at 900 °C for 2-h holding time followed by austempering at 300 and 350 °C for three different holding times (1.5, 2 and 2.5 h) at each austempering temperature. The influence of austempering temperature and time on the microstructural and mechanical properties was studied. Microstructural characterization, phase analysis, microhardness and mechanical properties were performed to understand the effect of austempering heat treatment on microstructure, austempering kinetics and mechanical properties of welded joints. In spite of significant variation in microstructures among all the three zones of DI weldment before austempering, the response of both weld metal and HAZ to austempering heat treatment similar to a base metal was noted. However, a significant variation in matrix structures (bainitic ferrite, retained austenite) as well as graphite nodules among the three zones was observed with changing the austempering temperature and holding time. Also, 100% joint efficiency of the welded joints was achieved at both 300 and 350 °C for 2-h holding time. Hardness and charpy impact toughness mostly depended on the volume fraction of retained austenite and carbon content. Based on the results of tensile and charpy impact testing, 350 °C and 2-h holding time could be considered as an optimum austempering condition for ADI weldment.

36 MATERIALS SCIENCE↗

Experimental studies of lithium-based surface chemistry for fusion plasma-facing materials applications

Lithium has enhanced the operational performance of fusion devices such as: TFTR, CDX-U, FTU, T-11 M, and NSTX. Lithium in the solid and liquid state has been studied extensively in laboratory experiments including its erosion and hydrogen-retaining properties. Reductions in physical sputtering up to 40–60% have been measured for deuterated solid and liquid lithium surfaces. Computational modeling indicates that up to a 1:1 deuterium volumetric retention in lithium is possible. This paper presents the results of systematic in situ laboratory experimental studies on the surface chemistry evolution of ATJ graphite under lithium deposition. Results are compared to post-mortem analysis of similar lithium surface coatings on graphite exposed to deuterium discharge plasmas in NSTX. Lithium coatings on plasma-facing components in NSTX have shown substantial reduction of hydrogenic recycling. Questions remain on the role lithium surface chemistry on a graphite substrate has on particle sputtering (physical and chemical) as well as hydrogen isotope recycling. This is particularly due to the lack of in situ measurements of plasma-surface interactions in tokamaks such as NSTX. Results suggest that the lithium bonding state on ATJ graphite is lithium peroxide and with sufficient exposure to ambient air conditions, lithium carbonate is generated. Further, correlation between both results is used to assess the role of lithium chemistry on the state of lithium bonding and implications on hydrogen pumping and lithium sputtering. In addition, reduction of factors between 10 and 30 reduction in physical sputtering from lithiated graphite compared to pure lithium or carbon is also measured.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Boosting the sodium storage behaviors of carbon materials in ether-based electrolyte through the artificial manipulation of microstructure

The porous carbon blacks rationally designed by a facile yet efficient NH 3 thermal etching route have been investigated as anode materials in an ether-based electrolyte for sodium-ion batteries. The as-synthesized CBN35 carbon black with a 35% weight loss after NH3 thermal etching exhibited a large specific charge capacity of 352 mAh g -1 at 50 mA g -1 and a superior rate capability of 101 mAh g -1 at 16000 mA g -1 , due to its highest microporosity, an appropriate surface area, a desirable microstructure, and a promising hybrid intercalation mechanism. Impressively, even cycled at 1600 mA g -1 over 3200 cycles, an outstanding reversible capacity of 103 mAh g -1 with a negligible 0.0162% capacity loss per cycle can still be achieved. Based on the multimodal characterizations including the structural probes of phase evolution for carbon materials, the electrochemical techniques, and the surface-sensitive XAS measurements, the exceptional electrochemical properties should stem from several merits of modified carbon black system. While the particular microporous structure provides relatively more accessible sodium storage sites, a novel hybrid intercalation mechanism in ether-based electrolyte would incorporate the sodium ion insertion into the disordered structure with the solvated sodium ion species co-intercalation into the graphitic phase. In addition to the diffusion-controlled redox reactions, the noticeable surface-induced pseudocapacitive reactions also significantly contribute to the charge storage upon sodiation and guarantee the rapid migrations of sodium ions/solvated compounds. In conclusion, this system further features a controlled emergence of a robust but thin solid electrolyte interphase layer, which could suppress the side reactions of active electrode with reactive electrolyte, maintain the fragile porous structure upon cycling, and facilitate the migrations of sodium ions and solvated sodium ion compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbon Nanotube Dispersion in Solvents and Polymer Solutions: Mechanisms, Assembly, and Preferences

Debundling and dispersion of carbon nanotubes (CNTs) in polymer solutions play a major role in the preparation of carbon nanofibers due to early effects on interfacial ordering and mechanical properties. A roadblock toward ultrastrong fibers is the difficulty to achieve homogeneous dispersions of CNTs in polyacrylonitrile (PAN) and poly(methyl methacrylate) (PMMA) precursor solutions in solvents such as dimethyl sulfoxide (DMSO), N,N-dimethylacetamide (DMAc), and N,N-dimethylformamide (DMF). In this contribution, molecular dynamics simulations with accurate interatomic potentials for graphitic materials that include virtual π electrons are reported to analyze the interaction of pristine single wall CNTs with the solvents and polymer solutions at 25 °C. The results explain the barriers toward dispersion of SWCNTs and quantify CNT-solvent, polymer-solvent, as well as CNT-polymer interactions in atomic detail. Debundling of CNTs is overall endothermic and unfavorable with dispersion energies of +20 to +30 mJ/m 2 in the pure solvents, + 20 to +40 mJ/m 2 in PAN solutions, and +20 to +60 mJ/m 2 in PMMA solutions. Differences arise due to molecular geometry, polar, van der Waals, and CH-π interactions. Among the pure solvents, DMF restricts CNT dispersion less due to the planar geometry and stronger van der Waals interactions. PAN and PMMA interact favorably with the pure solvents with dissolution energies of -0.7 to -1.1 kcal per mole monomer and -1.5 to -2.2 kcal per mole monomer, respectively. Adsorption of PMMA onto CNTs is stronger than that of PAN in all solvents as the molecular geometry enables more van der Waals contacts between alkyl groups and the CNT surface. Polar side groups in both polymers prefer interactions with the polar solvents. Higher polymer concentrations in solution lead to polymer aggregation via alkyl groups and reduce adsorption onto CNTs. PAN and PMMA solutions in DMSO and dilute solutions in DMF support CNT dispersion more than other combinations whereby the polymers significantly adsorb onto CNTs in DMSO solution. The observations by molecular simulations are consistent with available experimental data and solubility parameters and aid in the design of carbon nanofibers. The methods can be applied to other multiphase graphitic materials.

Chemistry↗

Tailoring oxidation degrees of graphene oxide by simple chemical reactions

High quality graphene oxide (GO) with controllable degrees of oxidation was synthesized by simple chemical reactions inspired by approaches to unzip single wall carbon nanotubes using strong oxidizing agents. As compared to the conventional Hummers method, these reactions are less exo-therm involved without emission of toxic gases. The structural characteristics of the synthesized GO with various oxidation degrees were evaluated by x-ray diffraction, x-ray photoelectron spectroscopy, Raman spectroscopy, thermal gravimetric analysis, and UV-vis-IR spectroscopy. GO with tailored degrees of oxidation displays tunable optoelectronic properties and may have a significant impact on developing graphene- or GO-based platforms for various technological applications.

36 MATERIALS SCIENCE↗

Stamping Nanoparticles onto the Electrode for Rapid Electrochemical Analysis in Microfluidics

Electrochemical analysis is an efficient way to study various materials. However, nanoparticles are challenging due to the difficulty in fabricating a uniform electrode containing nanoparticles. We developed novel approaches to incorporate nanoparticles as a working electrode (WE) in a three-electrode microfluidic electrochemical cell. Specifically, conductive epoxy was used as a medium for direct application of nanoparticles onto the electrode surface. Three approaches in this work were illustrated, including sequence stamping, mix stamping, and droplet stamping. Shadow masking was used to form the conductive structure in the WE surface on a thin silicon nitride (SiN) membrane. Two types of nanomaterials, namely cerium oxide (CeO2) and graphite, were chosen as representative nanoparticles. The as-fabricated electrodes with attached particles were characterized using atomic force microscopy (AFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Electrochemical analysis was performed to verify the feasibility of these nanoparticles as electrodes. Nanomaterials can be quickly assessed for their electrochemical properties using these new electrode fabrication methods in a microfluidic cell, offering a passport for rapid nanomaterial electrochemical analysis in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Development of Design Standards and Guidelines for Electromagnetic Compatibility and Lightning Protection for Spacecraft Utilizing Composite Materials

This final report presents information concerning technical accomplishments by Tec-Masters, Inc. (TMI) for this contract effort. This effort included the accomplishment and/or submission by TMI of the following items: (1) Literature Survey Report, Electrical Properties of Non-Metallic Composites by Mr. Hugh W. Denny; (2) Interim Report, Composite Materials - Conductivity, Shielding Effectiveness, and Current Carrying Capability by Mr. Ross W. Evans; (3) Fault Current Test Plan by Mr. Ross W. Evans (4) Fault Current Test Procedure by Mr. Ross W. Evans (5) Test Report, Fault Current Through Graphite Filament Reinforced Plastic, NASA CR-4774, Marshall Space Flight Center, Alabama, September 1996, by Mr. Ross W. Evans; (6) Test Plan, Lightning Effects on Composite Materials by Mr. Ross W. Evans; (7) Test Report, Lightning Effects on Composite Materials, NASA CR-4783, Marshall Space Flight Center, Alabama, February 1997, by Mr. Ross W. Evans; (8) Design Guidelines for Shielding Effectiveness, Current Carrying Capability, and the Enhancement of Conductivity of Composite Materials, NASA CR-4784, Marshall Space Flight Center, Alabama, September 1996, by Mr. Ross W. Evans. These items are not attached but are considered to be a part of this final report. Efforts on two additional items were accomplished at no increase in cost to NASA/MSFC. These items consisted of updating the 'MSFC EMC Design and Interference Control Handbook,' and revising the 'Design Guidelines for Shielding Effectiveness, Current Carrying Capability, and the Enhancement of Conductivity of Composite Materials.'

Camp, Dennis W.↗

Atmospheric pressure route to epitaxial nitrogen-doped trilayer graphene on 4H-SiC (0001) substrate

Large-area graphene film doped with nitrogen is of great interest for a wide spectrum of nanoelectronics applications, such as field effect devices, super capacitors, and fuel cells among many others. Here, we report on the structural and electronic properties of nitrogen doped trilayer graphene on 4H-SiC (0001) grown under atmospheric pressure. The trilayer nature of the growth is evidenced by scanning transmission electron microscopy. X-ray photoelectron spectroscopy shows the incorporation of 1.2% of nitrogen distributed in pyrrolic-N, and pyridinic-N configurations as well as a graphitic-N contribution. This incorporation causes an increase in the D band on the Raman signature indicating that the nitrogen is creating defects. Ultraviolet photoelectron spectroscopy shows a decrease of the work function of 0.3 eV due to the N-type doping of the nitrogen atoms in the carbon lattice and the edge defects. A top gate field effect transistor device has been fabricated and exhibits carrier mobilities up to 1300 cm{sup 2}/V s for holes and 850 cm{sup 2}/V s for electrons at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Antenna Technology for QUASAT application

A hybrid growth version of the advanced Sunflower, or precision deployable, antenna was adopted as the configuration proposed for the QUASAT very long baseline interferometry mission. The antenna consists of rigid panels of graphite-epoxy facesheets covering aluminum honeycomb sandwich. The six main folding panels are hinged to a cantilevered support ring attached to the periphery of the center section. Six pairs of intermediate panels are located between these panels and are hinged to each other and to the main panels. The flight configuration, antenna weight, a mass properties, frequency, and contour tolerance are discussed. The advantages of the solid antenna surface cover an all-mesh contour are examined.

Archer, J. S.↗

LDEF thermal control coatings post-flight analysis

The optical, physical, and chemical properties of selected spacecraft thermal control coatings, exposed for 10 months and 5.8 years on the leading edge (Row 9) of the LDEF, are reported. The following coatings were used: quartz/silver optical solar reflector; silvered FEP Teflon; S-13GLO, YB-71, and A-276 white paints; black paint; and sputter deposited coatings over graphite-epoxy composite substrates. The solar absorptance, total normal emittance, scanning electron and X-ray photoelectron microscopy, and X-ray diffraction analyses will be compared for the control, the 10 month exposed, and the 5.8 year exposed specimens. Data suggests that the high atomic flux over the last 6 months of the LDEF mission may have influenced the results from from this coatings experiment.

Slemp, Wayne S.↗

Phase transition induced strain in ZnO under high pressure

Under high pressure, the phase transition mechanism and mechanical property of material are supposed to be largely associated with the transformation induced elastic strain. However, the experimental evidences for such strain are scanty. The elastic and plastic properties of ZnO, a leading material for applications in chemical sensor, catalyst, and optical thin coatings, were determined using in situ high pressure synchrotron axial and radial x-ray diffraction. The abnormal elastic behaviors of selected lattice planes of ZnO during phase transition revealed the existence of internal elastic strain, which arise from the lattice misfit between wurtzite and rocksalt phase. Furthermore, the strength decrease of ZnO during phase transition under non-hydrostatic pressure was observed and could be attributed to such internal elastic strain, unveiling the relationship between pressure induced internal strain and mechanical property of material. Ultimately, these findings are of fundamental importance to understanding the mechanism of phase transition and the properties of materials under pressure.

36 MATERIALS SCIENCE↗

Thermo-Mechanical Response of a TRISO Fuel Particle in a Fusion/Fission Engine for Incineration of Weapons Grade Plutonium

The Laser Inertial Fusion-based (LIFE) engine is an advanced energy concept under development at Lawrence Livermore National Laboratory (LLNL). LIFE engine could be used to drive a subcritical fission blanket with fertile or fissile fuel. Current LIFE engine designs envisages fuel in pebble bed form with TRISO (tristructural isotropic) particles embedded in a graphite matrix, and pebbles flowing in molten salt Flibe (2LiF+BeF{sub 2}) coolant at T {approx} 700C. Weapons-grade plutonium (WGPu) fuel is an attractive option for LIFE engine involving the achievement of high fractional burnups in a short lifetime frame. However, WGPu LIFE engine operating conditions of high neutron fast fluence, high radiation damage, and high Helium and Hydrogen production pose severe challenges for typical TRISO particles. The thermo-mechanical fuel performance code HUPPCO (High burn-Up fuel Pebble Performance COde) currently under development accounts for spatial and time dependence of the material elastic properties, temperature, and irradiation swelling and creep mechanisms. In this work, some aspects of the thermo-mechanical response of TRISO particles used for incineration of weapons grade fuel in LIFE engine are analyzed. Preliminary results show the importance of developing reliable high-fidelity models of the performance of these new fuel designs and the need of new experimental data relevant to WGPu LIFE conditions.

36 MATERIALS SCIENCE↗

Synthesis and characterisation of a novel europium-based graphite intercalation compound

In the lithium-europium-graphite system, a novel ternary compound was synthesised by direct immersion of a pyrolytic graphite platelet in a molten lithium-based alloy with a well chosen Li/Eu ratio at 400 deg. C. The ternary compound exhibits poly-layered intercalated sheets mainly constituted of two europium planes. Its chemical formula can be written Li{sub x}EuC{sub 4}, since the amount of lithium is still not determined. The {sup 151}Eu Moessbauer spectra clearly indicate a +II valence for europium. The magnetic susceptibility and the magnetisation versus temperature reveal a complex behaviour which is qualitatively described thanks to structural hypothesis and analogies with the magnetic properties of the binary EuC{sub 6} compound. A first ferromagnetic transition occurring at 225 K is attributed to interactions between both intercalated europium planes. The lower temperature susceptibility behaviour can be interpreted by antiferromagnetic interactions between in-plane neighbours and ferromagnetic interactions along the c-axis. - Graphical abstract: 1D electronic density profiles along the c-axis of Li{sub x}EuC{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An investigation of the long-range and local structure of sub-stoichiometric zirconium carbide sintered at different temperatures

ZrC 1-x (sub-stoichiometric zirconium carbide), a group IV transition metal carbide, is being considered for various high temperature applications. Departure from stoichiometry changes the thermo-physical response of the material. Reported thermo-physical properties exhibit, in some cases, a degree of scatter with one likely contributor to this being the uncertainty in the C/Zr ratio of the samples produced. Conventional, methods for assigning C/Zr to samples are determined either by nominal stochiometric ratios or combustion carbon analysis. In this study, a range of stoichiometries of hot-pressed ZrC 1-x were examined by SEM, XRD, Raman spectroscopy and static 13 C NMR spectroscopy and used as a basis to correct the C/Zr. Graphite, amorphous, and ZrC 1-x carbon signatures are observed in the 13 C NMR spectra of samples and are determined to vary in intensity with sintering temperature and stoichiometry. In this study a method is outlined to quantify the stoichiometry of ZrC 1-x and free carbon phases, providing an improvement over the sole use and reliance of widely adopted bulk carbon combustion analysis. We report significantly lower C/Zr values determined by 13 C NMR analysis compared with carbon analyser and nominal methods. Furthermore, the location of carbon disassociated from the ZrC 1-x structure is analysed using SEM and Raman spectroscopy.

36 MATERIALS SCIENCE↗