Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mix Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Development of a 12-Thrust Chamber Kerosene /Oxygen Primary Rocket Sub-System for an Early (1964) Air-Augmented Rocket Ground-Test System

Airbreathing/Rocket combined-cycle, and specifically rocket-based combined- cycle (RBCC), propulsion systems, typically employ an internal engine flow-path installed primary rocket subsystem. To achieve acceptably short mixing lengths in effecting the "air augmentation" process, a large rocket-exhaust/air interfacial mixing surface is needed. This leads, in some engine design concepts, to a "cluster" of small rocket units, suitably arrayed in the flowpath. To support an early (1964) subscale ground-test of a specific RBCC concept, such a 12-rocket cluster was developed by NASA's Marshall Space Flight Center (MSFC). The small primary rockets used in the cluster assembly were modified versions of an existing small kerosene/oxygen water-cooled rocket engine unit routinely tested at MSFC. Following individual thrust-chamber tests and overall subsystem qualification testing, the cluster assembly was installed at the U. S. Air Force's Arnold Engineering Development Center (AEDC) for RBCC systems testing. (The results of the special air-augmented rocket testing are not covered here.) While this project was eventually successfully completed, a number of hardware integration problems were met, leading to catastrophic thrust chamber failures. The principal "lessons learned" in conducting this early primary rocket subsystem experimental effort are documented here as a basic knowledge-base contribution for the benefit of today's RBCC research and development community.

Pryor, D.↗

Development of Data Reduction Methods for Dynamic Stability Tests in a Magnetic Suspension and Balance System

The NASA/ODU 6-inch Magnetic Suspension and Balance System (MSBS) is operational in a “free-to-yaw” configuration in a subsonic wind tunnel. The MSBS hardware has been heavily modified over recent years to utilize a transverse magnetization scheme, with mixed electromagnetic and motion tracking camera position sensors and a relatively sophisticated control system. The project aims to provide a unique test capability for dynamic stability testing of planetary entry capsules, free from support interference. Aerodynamic tests are being conducted, with a focus of validation of the data reduction methods used to extract dynamic stability parameters. The unique complication is the existence of magnetic, aerodynamic, and mass centers, where magnetic, aerodynamic, and inertia forces respectively are resolved. The paper will report on tests of a family of EEV-like geometries, where the conical half-angle varied between 45 and 60 degrees in steps of 3.75 degrees. The paper will present experimental results from the parametric family of EEV-like geometries. Simulation results will also be presented, based on a two or three degree-of-freedom Simulink model. The model allows the exploration of the effects of non-coincident centers and the sensitivity of results arising from uncertainties in location.

Entry Systems Modeling↗

An Application of CFD to Guide Forced Boundary-Layer Transition at Subsonic and Transonic Speeds for a Lambda-Wing Configuration

A hybrid transition trip-dot sizing and placement test technique was extended to support recent experimental research on a moderately-swept hybrid wing-body Uninhabited Combat Air Vehicle configuration under study in a North Atlantic Treaty Organization Applied Vehicle Technology task group. The approach combines traditional test techniques with Computational Fluid Dynamics. The application had three-dimensional boundary layers that were simulated with either fully turbulent or mixed laminar-turbulent flow models using established Reynolds-averaged Navier-Stokes methods. Forced transition effectiveness was verified experimentally using sublimating chemicals during low-speed and transonic wind tunnel tests. Assessments were performed between tripped low Reynolds number data and un-tripped high Reynolds number data. The hybrid test technique is based on fundamental flow physics and as such could be applicable to other configurations.

UCAV↗

An Application of CFD to Guide Forced Boundary-Layer Transition at Subsonic and Transonic Speeds for a Lambda-Wing Configuration

A hybrid transition trip-dot sizing and placement test technique was extended to support recent experimental research on a moderately-swept hybrid wing-body Uninhabited Combat Air Vehicle configuration under study in a North Atlantic Treaty Organization Applied Vehicle Technology task group. The approach combines traditional test techniques with Computational Fluid Dynamics. The application had three-dimensional boundary layers that were simulated with either fully turbulent or mixed laminar-turbulent flow models using established Reynolds-averaged Navier-Stokes methods. Forced transition effectiveness was verified experimentally using sublimating chemicals during low-speed and transonic wind tunnel tests. Assessments were performed between tripped low Reynolds number data and un-tripped high Reynolds number data. The hybrid test technique is based on fundamental flow physics and as such could be applicable to other configurations.

Wind tunnel test technique↗

Comparison of Likelihood Methods for Generalized Linear Mixed Models with Application to Quiet Supersonic Flights 2018 Data

Repeated measurement will be a feature of the survey data collected during the Quesst missionX-59 community response tests (CRT). Since each participant will report his or her categorical level of annoyance in response to multiple events, the responses from any single individual may be correlated with one another. Several models within the class of generalized linear mixed models (GLMM) are pertinent to the analysis of correlated categorical outcomes; the random intercept logistic regression model is one example. Both Bayesian and frequentist methods for fitting these models are available, with frequentist methods relying on some form of approximation (of either an integral or the integrand) that appears in the marginal likelihood function. Given several anticipated similarities of the X-59 CRT data to data collected during a past risk reduction, Quiet Supersonic Flights 2018 (QSF18), this short note is intended to create awareness. It documents an instance in which a reported population average dose-response relationship derived from QSF18 single event data was distorted by the integral approximation applied in likelihood-based methods. We review some of the available literature on the topic, compare the outputs of several different computational approaches implemented in available statistical software, and present simple corrective actions that may be useful during the Quesst mission.

dose-response model↗

Methane and nonmethane hydrocarbon concentrations in the North and South Atlantic marine boundary layer

Methane and nonmethane hydrocarbon (NMHC) data were collected in the Atlantic marine boundary layer from 40 N to 32 S latitude during October and November 1980. Average volume mixing ratios for CH4 of 1.69 + or - 0.02 ppmv were obtained north of the intertropical convergence zone (ITCZ) and 1.60 + or - 0.02 ppmv south of the ITCZ. The hemispheric CH4 gradient was very sharp, decreasing rapidly between 14 N and 10 N latitude. Gaseous NMHC concentrations (based on response as CH4) were measured simultaneously and found to lie consistently within the standard error for the individual measurements + or - 0.02 ppmv) after correction for water vapor interference. The correction for water vapor response was large, frequently as much as 80% of the raw NMHC signal. Application of the student's t distribution test to the NMHC data set established that the mean northern and southern hemispheric NMHC mixing ratios measured, 0.016 and 0.010 ppmv, respectively, were statistically different at the 95% confidence level. These results indicate volatile NMHC mixing ratios average less than 0.02 ppmv over the Atlantic and represent the first set of semicontinuous NMHC measurements spanning the North and South Atlantic marine boundary layer.

Cofer, W. R., III↗

Investigation of mixing in a turbofan exhaust duct. II Computer code application and verification

A three-dimensional analysis of turbofan forced mixer nozzle aerodynamics demonstrates that the complex flow structure is dominated by geometrically induced secondary flow rather than by turbulence. The test apparatus consisted of a fixed upstream model section and a rotating shroud. The Mach number of the fan and core streams at the mixing plane (lobe exit) was 0.45, the bypass ratio was about 4, and the Reynolds number based on the shroud radius was 1,100,000. The three velocity components near the exit plane of the lobes were measured using flow angularity probes to provide information about the mixer inflow conditions for turbulent computations. The validity of a previous computer code was demonstrated in a comparison of the nozzle exit temperature data with the computed temperature distributions. The mechanism most responsible for the generation of secondary flow within the lobes is due to the turning of the fan and core streams in opposite radial directions.

Povinelli, L. A.↗

Mixed-Metal Nickel–Iron Oxide Aerogels for Oxygen Evolution Reaction

Alkaline electrolyte membrane electrolyzers are a promising technology to efficiently produce clean hydrogen without the use of critical raw materials. At the heart of these electrolyzers are the electrocatalysts, which facilitate the cathodic and anodic reactions, with the latter oxygen evolution reaction (OER) being the most sluggish. In recent years, aerogels have become a very well-studied class of materials due to their unique properties, including very high surface area. Until now, aerogels have not been used to catalyze the OER by themselves but were mainly considered catalyst supports. Here, mixed-metal nickel–iron oxide aerogels were synthesized with a modified epoxide route synthesis and tested as OER catalysts. Depending on the Ni/Fe ratio, they show very high catalytic activity and low overpotential to reach 10 mA cm –2 (at η = 380 mV). This activity is beyond that of the existing state-of-the-art platinum group metal-free OER catalysts.

PGM free catalysts↗

Synthesis of PDLLA/PLLA-bentonite nanocomposite through sonication

This paper concerns the synthesis of poly(D,L-lactic acid)/poly(L-lactic acid) bentonite nanocomposites. Poly (D,L-lactic acid) (PDLLA) was synthesized using lactic acid through the ZnO-catalyzed direct polycondensation method at vacuum pressure and poly(L-lactic acid) (PLLA) was synthesized with L-lactide by ring-opening polymerization method. The PDLLA/PLLA-bentonite nanocomposite films were synthesized using the solvent casting method. The nanoclay, bentonite, was prepared using the solution-intercalation method by dissolving the nanoparticles into chloroform before sonication. In this study, PDLLA/PLLA-bentonite nanocomposite films were produced using variable amounts of nanoclay and sonication times during the mixing of PDLLA/PLLA and bentonite. The properties of the PDLLA/PLLA nanocomposites were then characterized using the X-ray Diffraction (XRD), Universal Testing Machine (UTM), Water Vapor Permeability (WVP) tests, and the enzymatic biodegradability test. The XRD test was used to measure the intercalation of nanoclay layers in the PDLLA/PLLA matrix and the PDLLA/PLLA-bentonite intercalated nanocomposite films. It was found through these various tests that adding bentonite to the PDLLA/PLLA increases tensile strength to 56.76 MP. Furthermore, the biodegradability increases as well as the barrier properties of the polymers The different sonication time used during the mixing of the polymer solution with bentonite also affected the properties of the PDLLA/PLLA-bentonite nanocomposite films.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Two-moment Bulk Stratiform Cloud Microphysics in the Grid-point Atmospheric Model of IAP LASG (GAMIL)

A two-moment bulk stratiform microphysics scheme, including recently developed physically-based droplet activation/ice nucleation parameterizations has been implemented into the Grid-point Atmospheric Model of IAP LASG (GAMIL) as an effort to enhance the model capability for studying aerosol indirect effects. Unlike the previous one-moment cloud microphysics scheme, the new scheme produces reasonable representation of cloud particle size and number concentration. This scheme captures the observed spatial variations in cloud droplet number concentrations. Simulated ice crystal number concentrations in cirrus clouds qualitatively agree with in-situ observations. The longwave and shortwave cloud forcing are in better agreement with observations. Sensitivity tests show that the column cloud droplet number concentrations calculated from two different droplet activation parameterizations are similar. However, ice crystal number concentration in mixed-phased clouds is sensitive to different heterogeneous freezing formulations. The simulation with high ice crystal number concentration in mixed-phase clouds has less liquid water path and weaker cloud forcing. Furthermore, ice crystal number concentration in cirrus clouds is sensitive to different ice nucleation parameterizations. Sensitivity tests also suggest that impact of pre-existing ice crystals on homogeneous freezing in old clouds should be taken into account.

(GAMIL)↗

Dilution jet mixing program, supplementary report

The velocity and temperature distributions predicted by a 3-D numerical model and experimental measurements are compared. Empirical correlations for the jet velocity trajectory developed are presented. The measured velocity distributions for all test cases of phase through phase 3 are presented in the form of contour and oblique plots. quantification of the effects of the following on the jet mixing characteristics with a confined crossflow are: (1) orifice geometry momentum flux ratio and density ratio; (2) nonuniform mainstream temperature and velocity profiles upstream of dilution orifices; (3) cold versus hot jet injection; (4) cross-stream flow are a convergence as encountered in practical dilution zone geometries; (5) 2-D slot versus circular orifices; (6) discrete noncirculcer orifices; (7) single-sided versus opposed jets; (8) single row of jets.

Srinivasan, R.↗

Study on the mechanism of diametral cladding strain and mixed-oxide fuel element breaching in slow-ramp extended overpower transients

Cladding strain caused by fuel/cladding mechanical interaction (FCMI) was evaluated for mixed-oxide fuel elements subjected to 70–90% slow-ramp extended overpower transient tests in the experimental breeder reactor II. Calculated transient-induced cladding strains were correlated with cumulative damage fractions (CDFs) using cladding strength correlations. In a breached high-smeared density solid fuel element with low strength cladding, cladding thermal creep strain was significantly increased to approximately half the transient-induced cladding strain that was considered to be caused by the tertiary creep when the CDF was close to the breach criterion (=1.0), with the remaining strain due to instantaneous plastic deformation. In low-smeared density annular fuel elements, FCMI load was significantly mitigated and resulted in little cladding strain. The CDFs of the annular fuel elements were lower than 0.01 at the end of the overpower transient, indicating a substantial margin to breach. A substantial margin to breach was also maintained in a high-smeared density fuel element with high strength cladding.

99 GENERAL AND MISCELLANEOUS↗

Irradiation tests of prototype self-powered gamma and neutron detectors

In the framework of the SCK.CEN-CEA Joint Instrumentation Laboratory, we are developing and optimizing a self-powered detector for selective in-core monitoring of the gamma field. Several prototypes with bismuth emitters were developed and tested in a pure gamma field (the PAGURE gamma irradiation facility at CEA) and in mixed neutron and gamma fields (in the OSIRIS reactor at CEA and in the BR2 reactor at SCK.CEN). Detailed MCNP modelling was performed to calculate the gamma and neutron sensitivities. Apart from a few failing prototypes, all detectors showed equilibrium signals proportional to the gamma field with a good long-term stability (under irradiation during several weeks). A tubular geometry design was finally selected as the most appropriate for in-core gamma detection, coupling a larger sensitivity with better response characteristics. In the same experiment in BR2 six prototype Self-Powered Neutron Detectors (SPNDs) with continuous sheaths (i.e. without any weld between the sensitive part and the cable) were extensively tested: two SPNDs with Co emitter, two with V emitter and two with Rh emitters, with varying geometries. All detector responses were verified to be proportional to the reactor power. The prompt and delayed response contributions were quantified. The signal contributions due to the impact of gamma rays were experimentally determined. The evolution of the signals was continuously followed during the full irradiation period. The signal-to-noise level was observed to be well below 1% in typical irradiation conditions. The absolute neutron and gamma responses for all SPNDs are consistent. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High pressure Mach 10 to 20 electrothermal hypersonic wind tunnel

A new technique is described for generating high enthalpy, long pulse flows for testing scramjet combustors at equivalent flight Mach numbers of 10 to 20. The approach derives from high pressure discharge technology developed for electrothermal guns and space thrusters. Cryogenic liquid air is heated with a high power electric discharge (500 MW for a 15 kg/sec test flow rate) in a capillary tube, generating a quasi-steady pressure of up to 6800 atm at 20,000 K. The heated air is mixed with additional cryogenic air and is expanded in a conventional supersonic nozzle to 0.5 to 1 atm at 3000 to 6000 m/sec. Combustion and nozzle expansion test time of approximately 300 m/sec are contemplated. Facility nozzle chemical kinetics calculations show that above Mach 16 increasing concentrations of argon and oxygen replenishment are required to obtain suitable test conditions. Initial experiments on a subscale test rig are described for 0.5 kg/sec and 300 atm pressure.

Burton, R. L.↗

Comparison of experiment with calculations using curvature-corrected zero and two equation turbulence models for a two-dimensional U-duct

In this paper experimental measurements are compared with Navier-Stokes calculations using seven different turbulence models for the internal flow in a two-dimensional U-duct. The configuration is representative of many internal flows of engineering interst that experience strong curvature. In an effort to improve agreement, this paper tests several versions of the two-equation k-epsilon turbulence model including the standard version, an extended version with a production range time scale, and a version that includes curvature time scales. Each is tested in its high and low Reynolds number formulations. Calculations using these new models and the original mixing length model are compared here with measurements of mean and turbulence velocities, static pressure and skin friction in the U-duct at two Reynolds numbers. The comparisons show that only the low Reynolds number version of the extended k-epsilon model does a reasonable job of predicting the important features of this flow at both Reynolds numbers tested.

Monson, D. J.↗

Improved silicon carbide for advanced heat engines

The development of high strength, high reliability silicon carbide parts with complex shapes suitable for use in advanced heat engines is studied. Injection molding was the forming method selected for the program because it is capable of forming complex parts adaptable for mass production on an economically sound basis. The goals were to reach a Weibull characteristic strength of 550 MPa (80 ksi) and a Weibull modulus of 16 for bars tested in four-point loading. Statistically designed experiments were performed throughout the program and a fluid mixing process employing an attritor mixer was developed. Compositional improvements in the amounts and sources of boron and carbon used and a pressureless sintering cycle were developed which provided samples of about 99 percent of theoretical density. Strengths were found to improve significantly by annealing in air. Strengths in excess of 550 MPa (80 ksi) with Weibull modulus of about 9 were obtained. Further improvements in Weibull modulus to about 16 were realized by proof testing. This is an increase of 86 percent in strength and 100 percent in Weibull modulus over the baseline data generated at the beginning of the program. Molding yields were improved and flaw distributions were observed to follow a Poisson process. Magic angle spinning nuclear magnetic resonance spectra were found to be useful in characterizing the SiC powder and the sintered samples. Turbocharger rotors were molded and examined as an indication of the moldability of the mixes which were developed in this program.

Whalen, Thomas J.↗

Fundamentals of Reservoir Surface Energy as Related to Surface Properties, Wettability, Capillary Action, and Oil Recovery from Fractured Reservoirs by Spontaneous Imbibition

The objective of this project is to increase oil recovery from fractured reservoirs through improved fundamental understanding of the process of spontaneous imbibition by which oil is displaced from the rock matrix into the fractures. Spontaneous imbibition is fundamentally dependent on the reservoir surface free energy but this has never been investigated for rocks. In this project, the surface free energy of rocks will be determined by using liquids that can be solidified within the rock pore space at selected saturations. Thin sections of the rock then provide a two-dimensional view of the rock minerals and the occupant phases. Saturations and oil/rock, water/rock, and oil/water surface areas will be determined by advanced petrographic analysis and the surface free energy which drives spontaneous imbibition will be determined as a function of increase in wetting phase saturation. The inherent loss in surface free energy resulting from capillary instabilities at the microscopic (pore level) scale will be distinguished from the decrease in surface free energy that drives spontaneous imbibition. A mathematical network/numerical model will be developed and tested against experimental results of recovery versus time over broad variation of key factors such as rock properties, fluid phase viscosities, sample size, shape and boundary conditions. Two fundamentally important, but not previously considered, parameters of spontaneous imbibition, the capillary pressure acting to oppose production of oil at the outflow face and the pressure in the non-wetting phase at the no-flow boundary versus time, will also be measured and modeled. Simulation and network models will also be tested against special case solutions provided by analytic models. In the second stage of the project, application of the fundamental concepts developed in the first stage of the project will be demonstrated. The fundamental ideas, measurements, and analytic/numerical modeling will be applied to mixed-wet rocks. Imbibition measurements will include novel sensitive pressure measurements designed to elucidate the basic mechanisms that determine induction time and drive the very slow rate of spontaneous imbibition commonly observed for mixed-wet rocks. In further demonstration of concepts, three approaches to improved oil recovery from fractured reservoirs will be tested; use of surfactants to promote imbibition in oil wet rocks by wettability alteration: manipulation of injection brine composition: reduction of the capillary back pressure which opposes production of oil at the fracture face.

03 NATURAL GAS↗

LAW Glass Testing by Long-Term PCT to Support Disposal at IDF

About 50 million gallons of high-level mixed waste is currently stored in underground tanks at The United States Department of Energy’s (DOE’s) Hanford site in the State of Washington. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) will provide DOE’s Office of River Protection (ORP) with a means of treating this waste by vitrification for subsequent disposal. The tank waste will be separated into low- and high-activity waste fractions, which will then be vitrified respectively into Immobilized Low Activity Waste (ILAW) and Immobilized High Level Waste (IHLW) products. The ILAW product will be disposed in an engineered facility – the Integrated Disposal Facility (IDF) – on the Hanford site, while the IHLW product is designed for a national deep geological disposal facility for high-level nuclear waste. The ILAW and IHLW products must meet a variety of requirements with respect to protection of the environment before they can be accepted for disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗