Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nonlinear programming.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

A nonlinear propulsion system simulation technique for piloted simulators

A real time digital simulation technique providing the capabilities needed to evaluate propulsion system performance and aircraft system interaction on NASA manned flight simulators, is discussed. A parameter correlation technique is used with real and pseudo dynamics in a stable integration convergence loop. The cycle time reported was 2.0 ms on one computer and 5.7 ms on the simulator computer. The model was found to be stable and accurate with time up to 50 ms. It is concluded that the program has generated a valuable simulation technology and flight simulator experience by providing an adequate level of detail to evaluate propulsion systems in a simulated flight environment.

Mihaloew, J. R.↗

Nonlinear potential analysis techniques for supersonic aerodynamic design

A numerical method based on the conservation form of the full potential equation has been applied to the problem of three-dimensional supersonic flows with embedded subsonic regions. The governing equation is cast in a nonorthogonal coordinate system, and the theory of characteristics is used to accurately monitor the type-dependent flow field. A conservative switching scheme is employed to transition from the supersonic marching procedure to a subsonic relaxation algorithm and vice versa. The newly developed computer program can handle arbitrary geometries with fuselage, canard, wing, flow through nacelle, vertical tail and wake components at combined angles of attack and sideslip. Results are obtained for a variety of configurations that include a Langley advanced fighter concept with fuselage centerline nacelle, Rockwell's Advanced Tactical Fighter (ATF) with wing mounted nacelles, and the Shuttle Orbiter configuration. Comparisons with available experiments were good.

Shankar, V.↗

Automatic Differentiation in MetaPhysicL and Its Applications in MOOSE

Efficient solution via Newton’s method of nonlinear systems of equations requires an accurate representation of the Jacobian, corresponding to the derivatives of the component residual equations with respect to the degrees of freedom. In practice these systems of equations often arise from spatial discretization of partial differential equations used to model physical phenomena. These equations may involve domain motion or material equations that are complex functions of the systems’ degrees of freedom. Computing the Jacobian by hand in these situations is arduous and prone to error. Finite difference approximations of the Jacobian or its action are prone to truncation error, especially in multiphysics settings. Symbolic differentiation packages may be used, but often result in an excessive number of terms in realistic model scenarios. An alternative to symbolic and numerical differentiation is automatic differentiation (AD), which propagates derivatives with every elementary operation of a computer program, corresponding to continual application of the chain rule. Automatic differentiation offers the guarantee of an exact Jacobian at a relatively small overhead cost. In this work, we outline the adoption of AD in the Multiphysics Object Oriented Simulation Environment (MOOSE) via the MetaPhysicL package. We describe the application of MOOSE’s AD capability to several sets of physics that were previously infeasible to model via hand-coded or Jacobian-free simulation techniques, including arbitrary Lagrangian-Eulerian and level-set simulations of laser melt pools, phase-field simulations with free energies provided through neural networks, and metallic nuclear fuel simulations that require inner Newton loop calculation of nonlinear material properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Extracting the turbulent flow-field from beam emission spectroscopy images using velocimetry

The 2D turbulent E × B flow-field is inferred from density fluctuation images obtained with the beam emission spectroscopy diagnostic on DIII-D using the orthogonal dynamic programming velocimetry algorithm. A synthetic turbulence model is used to test the algorithm and optimize it for measuring zonal flows. Zonal flow measurements are found to require a signal-to-noise ratio above ~10 and a zonal flow wavelength longer than ~2 cm. Comparison between the velocimetry-estimated flow-field and the E × B flow-field using a nonlinear gyrokinetic GENE simulation finds that the flow-fields have identical spatial structure and differ only by the mean turbulence phase velocity, which is spatially uniform in this flux tube simulation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A numerical calculation of outward propagation of solar disturbances

The responses of the solar atmosphere due to an outward propagation shock are examined by employing the Lax-Wendroff method to solve the set of nonlinear partial differential equations in the model of the solar atmosphere. It is found that this theoretical model can be used to explain the solar phenomena of surge and spray. A criterion to discriminate the surge and spray is established and detailed information concerning the density, velocity, and temperature distribution with respect to the height and time is presented. The complete computer program is also included.

Wu, S. T.↗

Controls-structures interaction guest investigator program: Overview and phase 1 experimental results and future plans

The NASA Controls-Structures Interaction (CSI) Guest Investigator program is described in terms of its support of the development of CSI technologies. The program is based on the introduction of CSI researchers from industry and academia to available test facilities for experimental validation of technologies and methods. Phase 1 experimental results are reviewed with attention given to their use of the Mini-MAST test facility and the facility for the Advance Control Evaluation of Structures. Experiments were conducted regarding the following topics: collocated/noncollocated controllers, nonlinear math modeling, controller design, passive/active suspension systems design, and system identification and fault isolation. The results demonstrate that significantly enhanced performance from the control techniques can be achieved by integrating knowledge of the structural dynamics under consideration into the approaches.

Smith-Taylor, Rudeen↗

Multiscale Prediction of Yarn Pullout Failure Mode in Unreinforced Textile Fabrics

Unreinforced woven fabrics have been implemented in a variety of high performance applications, including body armor, deployable structures, and as the reinforcement material in composites. Multiscale modeling techniques have significantly improved the capabilities of simulation-based tools to capture fabric mechanics efficiently and accurately, but often lack in their prediction of failure and require pairing with finite element analysis (FEA) software, limiting their application to the design of ‘fit-for-purpose’ materials. NASA’s Multiscale Analysis Tool (NASMAT) is a standalone multiscale program that has been traditionally used in the analysis of reinforced composites materials. More recently, it has been amended to simulate unreinforced fabric behavior by allowing the geometric state of the tows to change with applied loading due to the lack of a reinforcement material, such as the matrix seen in composites. Previous work has shown the ability of NASMAT to capture nonlinear macroscale behavior by predicting geometric changes in the state of each subcell as a function of the applied loading and allowing each subcell in the analysis to rotate according to these predicted changes, as well as predict nonlinear behavior due to the fiber breakage failure mode. In this work, the capability of predicting the onset and propagation of failure in plain woven fabrics in NASMAT is presented for the yarn pullout failure mode, which occurs when a fabric is loaded at an off-axis angle relative to the warp of weft tow direction. Yarn pullout behavior is initiated by determining the applied load in which the shear resistance of the contact area between yarn families is overcome. When failure is initiated, yarn pullout is determined to have occurred when the applied displacement, calculated from global strain, exceeds the deformed position of a given contact points between yarn families, determined from pin-joint kinematics. Contact points where pullout has occurred contribute to a global damage parameter used to modify the homogenized stiffness of the fabric, resulting in nonlinear behavior observed at the macroscale. The off-axis loading behavior and yarn pullout failure theory have been developed and implemented into NASMAT such that users can simulate off-axis tensile behavior of fabrics in a single, standalone multiscale tool. Simulations are compared to uniaxial tensile tests at various off-axis angles to demonstrate the capability of the tool in its prediction of both the onset of failure at each off-axis angles and the stress-strain behavior as failure progresses.

Materials↗

Building Battery Energy Storage System Performance Data into an Economic Assessment

Economic assessments of battery energy storage systems (BESSs) rely on optimal dispatch methods to capture temporal interdependency of BESS operations and coupling among different grid applications. Many existing BESS economic assessment studies are based on a simplified first-order scalar model using BESS nameplate numbers. Such a method cannot accurately capture varying capabilities and nonlinear dynamics of a BESS, leading to inaccurate assessment results. This paper presents a practical implementation of performance data into the economic assessment of the BESSs recently developed within the Snohomish Public Utility District system in Washington State. Extensive testing conducted over multiple seasons is used to assess the technical performance and develop high-fidelity models of the BESSs. A dynamic programming algorithm is proposed to optimally dispatch the BESSs and assess the potential benefits from stacked value streams. The proposed method can be adapted for the economic assessment of other BESSs with different applications.

Wu, Di↗

Dynamic force matching: A method for constructing dynamical coarse-grained models with realistic time dependence

Coarse-grained (CG) models of molecular systems, with fewer mechanical degrees of freedom than an all-atom model, are used extensively in chemical physics. It is generally accepted that a coarse-grained model that accurately describes equilibrium structural properties (as a result of having a well constructed CG potential energy function) does not necessarily exhibit appropriate dynamical behavior when simulated using conservative Hamiltonian dynamics for the CG degrees of freedom on the CG potential energy surface. Attempts to develop accurate CG dynamic models usually focus on replacing Hamiltonian motion by stochastic but Markovian dynamics on that surface, such as Langevin or Brownian dynamics. However, depending on the nature of the system and the extent of the coarse-graining, a Markovian dynamics for the CG degrees of freedom may not be appropriate. In this paper, we consider the problem of constructing dynamic CG models within the context of the Multi-Scale Coarse-graining (MS-CG) method of Voth and coworkers. We propose a method of converting a MS-CG model into a dynamic CG model by adding degrees of freedom to it in the form of a small number of fictitious particles that interact with the CG degrees of freedom in simple ways and that are subject to Langevin forces. The dynamic models are members of a class of nonlinear systems interacting with special heat baths that were studied by Zwanzig [J. Stat. Phys. 9, 215 (1973)]. The properties of the fictitious particles can be inferred from analysis of the dynamics of all-atom simulations of the system of interest. This is analogous to the fact that the MS-CG method generates the CG potential from analysis of equilibrium structures observed in all-atom simulation data. The dynamic models generate a non-Markovian dynamics for the CG degrees of freedom, but they can be easily simulated using standard molecular dynamics programs. We present tests of this method on a series of simple examples that demonstrate that the method provides realistic dynamical CG models that have non-Markovian or close to Markovian behavior that is consistent with the actual dynamical behavior of the all-atom system used to construct the CG model. Both the construction and the simulation of such a dynamic CG model have computational requirements that are similar to those of the corresponding MS-CG model and are good candidates for CG modeling of very large systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Bulk-Flow Analysis of Hybrid Thrust Bearings for Advanced Cryogenic Turbopumps

A bulk-flow analysis and computer program for prediction of the static load performance and dynamic force coefficients of angled injection, orifice-compensated hydrostatic/hydrodynamic thrust bearings have been completed. The product of the research is an efficient computational tool for the design of high-speed thrust bearings for cryogenic fluid turbopumps. The study addresses the needs of a growing technology that requires of reliable fluid film bearings to provide the maximum operating life with optimum controllable rotordynamic characteristics at the lowest cost. The motion of a cryogenic fluid on the thin film lands of a thrust bearing is governed by a set of bulk-flow mass and momentum conservation and energy transport equations. Mass flow conservation and a simple model for momentum transport within the hydrostatic bearing recesses are also accounted for. The bulk-flow model includes flow turbulence with fluid inertia advection, Coriolis and centrifugal acceleration effects on the bearing recesses and film lands. The cryogenic fluid properties are obtained from realistic thermophysical equations of state. Turbulent bulk-flow shear parameters are based on Hirs' model with Moody's friction factor equations allowing a simple simulation for machined bearing surface roughness. A perturbation analysis leads to zeroth-order nonlinear equations governing the fluid flow for the thrust bearing operating at a static equilibrium position, and first-order linear equations describing the perturbed fluid flow for small amplitude shaft motions in the axial direction. Numerical solution to the zeroth-order flow field equations renders the bearing flow rate, thrust load, drag torque and power dissipation. Solution to the first-order equations determines the axial stiffness, damping and inertia force coefficients. The computational method uses well established algorithms and generic subprograms available from prior developments. The Fortran9O computer program hydrothrust runs on a Windows 95/NT personal computer. The program, help files and examples are licensed by Texas A&M University Technology License Office. The study of the static and dynamic performance of two hydrostatic/hydrodynamic bearings demonstrates the importance of centrifugal and advection fluid inertia effects for operation at high rotational speeds. The first example considers a conceptual hydrostatic thrust bearing for an advanced liquid hydrogen turbopump operating at 170,000 rpm. The large axial stiffness and damping coefficients of the bearing should provide accurate control and axial positioning of the turbopump and also allow for unshrouded impellers, therefore increasing the overall pump efficiency. The second bearing uses a refrigerant R134a, and its application in oil-free air conditioning compressors is of great technological importance and commercial value. The computed predictions reveal that the LH2 bearing load capacity and flow rate increase with the recess pressure (i.e. increasing orifice diameters). The bearing axial stiffness has a maximum for a recess pressure rati of approx. 0.55. while the axial damping coefficient decreases as the recess pressure ratio increases. The computer results from three flow models are compared. These models are a) inertialess, b) fluid inertia at recess edges only, and c) full fluid inertia at both recess edges and film lands. The full inertia model shows the lowest flow rates, axial load capacity and stiffness coefficient but on the other hand renders the largest damping coefficients and inertia coefficients. The most important findings are related to the reduction of the outflow through the inner radius and the appearance of subambient pressures. The performance of the refrigerant hybrid thrust bearing is evaluated at two operating speeds and pressure drops. The computed results are presented in dimensionless form to evidence consistent trends in the bearing performance characteristics. As the applied axial load increases, the bearing film thickness and flow rate decrease while the recess pressure increases. The axial stiffness coefficient shows a maximum for a certain intermediate load while the damping coefficient steadily increases. The computed results evidence the paramount of centrifugal fluid inertia at low recess pressures (i.e. low loads), and where there is actually an inflow through the bearing inner diameter, accompanied by subambient pressures just downstream of the bearing recess edge. These results are solely due to centrifugal fluid inertia and advection transport effects. Recommendations include the extension of the computer program to handle flexure pivot tilting pad hybrid bearings and the ability to calculate moment coefficients for shaft angular misalignments.

SanAndres, Luis↗

Method to predict external store carriage characteristics at transonic speeds

Development of a computational method for prediction of external store carriage characteristics at transonic speeds is described. The geometric flexibility required for treatment of pylon-mounted stores is achieved by computing finite difference solutions on a five-level embedded grid arrangement. A completely automated grid generation procedure facilitates applications. Store modeling capability consists of bodies of revolution with multiple fore and aft fins. A body-conforming grid improves the accuracy of the computed store body flow field. A nonlinear relaxation scheme developed specifically for modified transonic small disturbance flow equations enhances the method's numerical stability and accuracy. As a result, treatment of lower aspect ratio, more highly swept and tapered wings is possible. A limited supersonic freestream capability is also provided. Pressure, load distribution, and force/moment correlations show good agreement with experimental data for several test cases. A detailed computer program description for the Transonic Store Carriage Loads Prediction (TSCLP) Code is included.

Rosen, Bruce S.↗

Project Management Using Modern Guidance, Navigation and Control Theory

Implementing guidance, navigation, and control (GN&C) theory principles and applying them to the human element of project management and control is not a new concept. As both the literature on the subject and the real-world applications are neither readily available nor comprehensive with regard to how such principles might be applied, this paper has been written to educate the project manager on the "laws of physics" of his or her project (not to teach a GN&C engineer how to become a project manager) and to provide an intuitive, mathematical explanation as to the control and behavior of projects. This paper will also address how the fundamental principles of modern GN&C were applied to the National Aeronautics and Space Administration's (NASA) Constellation Program (CxP) space suit project, ensuring the project was managed within cost, schedule, and budget. A project that is akin to a physical system can be modeled and managed using the same over arching principles of GN&C that would be used if that project were a complex vehicle, a complex system(s), or complex software with time-varying processes (at times nonlinear) containing multiple data inputs of varying accuracy and a range of operating points. The classic GN&C theory approach could thus be applied to small, well-defined projects; yet when working with larger, multiyear projects necessitating multiple organizational structures, numerous external influences, and a multitude of diverse resources, modern GN&C principles are required to model and manage the project. The fundamental principles of a GN&C system incorporate these basic concepts: State, Behavior, Feedback Control, Navigation, Guidance and Planning Logic systems. The State of a system defines the aspects of the system that can change over time; e.g., position, velocity, acceleration, coordinate-based attitude, and temperature, etc. The Behavior of the system focuses more on what changes are possible within the system; this is denoted in the state of the system. The behavior of a system, as captured in the system modeling, when properly done will aid in accurately predicting future system performance. The Feedback Control system understands the state and behavior of the system and uses feedback to adjust control inputs into the system. The feedback, which is the right arm of the Control system, allows change to be affected in the overall system; it therefore is important to not only correctly identify the system feedback inputs, but also the system response to the feedback inputs. The Navigation system takes multiple data inputs and based on a priori knowledge of the inputs, develops a statistically based weighting of the inputs and measurements to determine the system's state. Guidance and Planning Logic of the system, complete with an understanding of where the system is (provided by the Navigation system), will in turn determine where the system needs to be and how to get it there. With any system/project, it is critical that the objective of the system/project be clearly defined -- not only to plan but to measure performance and to aid in guiding the system or the project. The system principles discussed above, which can be and have been applied to the current CxP space suit development project, can also be mapped to real-world constituents, thus allowing project managers to apply systems theories that are well defined in engineering and mathematics to a discipline (i.e., Project Management) that historically has been based in personal experience and intuition. This mapping of GN&C theory to Project Management will, in turn, permit a direct, methodical approach to Project Management, planning and control providing a tool to help predict (and guide) performance and an understanding of the project constraints, how the project can be controlled, and the impacts to external influences and inputs. This approach, to a project manager, flows down to the three bottom-line variables of cost, schedule, and scope ando the needed control of these three variables to successfully perform and complete a project.

Hill, Terry R.↗

Review and evaluation of recent developments in melic inlet dynamic flow distortion prediction and computer program documentation and user's manual estimating maximum instantaneous inlet flow distortion from steady-state total pressure measurements with full, limited, or no dynamic data

A review of the Melick method of inlet flow dynamic distortion prediction by statistical means is provided. These developments include the general Melick approach with full dynamic measurements, a limited dynamic measurement approach, and a turbulence modelling approach which requires no dynamic rms pressure fluctuation measurements. These modifications are evaluated by comparing predicted and measured peak instantaneous distortion levels from provisional inlet data sets. A nonlinear mean-line following vortex model is proposed and evaluated as a potential criterion for improving the peak instantaneous distortion map generated from the conventional linear vortex of the Melick method. The model is simplified to a series of linear vortex segments which lay along the mean line. Maps generated with this new approach are compared with conventionally generated maps, as well as measured peak instantaneous maps. Inlet data sets include subsonic, transonic, and supersonic inlets under various flight conditions.

Schweikhard, W. G.↗

Modeling Multiscale-Multiphase-Multicomponent Subsurface Reactive Flows Using Advanced Computing

The DOE SciDAC program funded a team that developed PFLOTRAN, the next-generation (peta-scale) massively parallel, multiphase, multicomponent reactive flow and transport code. These codes are required to improve understanding and risk management of subsurface contaminant migration and geological sequestration of carbon dioxide. The important fate and transport processes occurring in the subsurface span a wide range of spatial and temporal scales, and involve nonlinear interactions among many different chemical constituents. Due to the complexity of this problem, modeling subsurface processes normally requires simplifying assumptions. However, tools of advanced scientific computing that have been used in other areas such as energy and materials research can also help address challenging problems in the environmental and geoscience fields. The overall project was led by Los Alamos National Laboratory and included Argonne, Oak Ridge and Pacific Northwest National Laboratories, in addition to the University of Illinois. This report summarizes the results of the research done at the University of Illinois, which focused on improvements to the underlying physical and computational modeling of certain transport and mixing processes.

58 GEOSCIENCES↗

QMU as an Approach to Strengthening the Predictive Capabilities of Complex Models

Complex systems are made up of multiple interdependent parts, and the behavior of the entire system cannot always be directly inferred from the behavior of the individual parts. They are nonlinear and system responses are not necessarily additive. Examples of complex systems include energy, cyber and telecommunication infrastructures, human and animal social structures, and biological structures such as cells. To meet the goals of infrastructure development, maintenance, and protection for cyber-related complex systems, novel modeling and simulation technology is needed. Sandia has shown success using M&S in the nuclear weapons (NW) program. However, complex systems represent a significant challenge and relative departure from the classical M&S exercises, and many of the scientific and mathematical M&S processes must be re-envisioned. Specifically, in the NW program, requirements and acceptable margins for performance, resilience, and security are well-defined and given quantitatively from the start. The Quantification of Margins and Uncertainties (QMU) process helps to assess whether or not these safety, reliability and performance requirements have been met after a system has been developed. In this sense, QMU is used as a sort of check that requirements have been met once the development process is completed. In contrast, performance requirements and margins may not have been defined a priori for many complex systems, (i.e. the Internet, electrical distribution grids, etc.), particularly not in quantitative terms. This project addresses this fundamental difference by investigating the use of QMU at the start of the design process for complex systems. Three major tasks were completed. First, the characteristics of the cyber infrastructure problem were collected and considered in the context of QMU-based tools. Second, UQ methodologies for the quantification of model discrepancies were considered in the context of statistical models of cyber activity. Third, Bayesian methods for optimal testing in the QMU framework were developed. This completion of this project represent an increased understanding of how to apply and use the QMU process as a means for improving model predictions of the behavior of complex systems.

Gray, Genetha Anne↗

Postbuckling analysis using a general purpose code

A new capability for solving postbuckling problems in shell structures is described. The matrix theory to adapt Newton's method to nonlinear finite element shell analysis is outlined first. The matrix theory is directed at writing consistent linear algebratic equations for problems where the tangent stiffness matrix is singular or nearly singular. The matrix theory suggests a change of variables as part of the usual iterative procedure in Newton's method. The change of variables is shown to be feasible for introduction into the algorithm programmed in general purpose codes for finite element analysis of structures. Numerical results from a new option that has been programmed in an existing general purpose code are presented. The analysis of shell structures for collapse and for branching at bifurcation loads is illustrated by the numerical examples.

Thurston, G. A.↗

Coupled aerodynamic and acoustical predictions for turboprops

To predict the noise fields for proposed turboprop airplanes, an existing turboprop noise code by Farassat has been modified to accept blade pressure inputs from a three-dimensional aerodynamic code. A Euler-type code can handle the nonlinear transonic flow of these high-speed, highly swept blades. This turbofan code was modified to allow the calculation mesh to extend to about twice the blade radius and to apply circumferential periodicity rather than solid-wall boundary conditions on the blade in the region between the blade tip and the outer shroud. Outputs were added for input to the noise prediction program and for color contour plots of various flow variables. The Farassat input subroutines were modified to read files of blade coordinates and predicted surface pressures. Aerodynamic and acoustic results are shown for the SR-3 model blade. Comparison of the acoustic predicted results with measured data show good agreement.

Clark, Bruce J.↗

PyRAT - python radiography analysis tool (u)

PyRAT is a radiography analysis tool used to reconstruction images of unknown 1-0 objects. The tool is written in Python and developed for use on LINUX and Windows platforms. The tool is capable of performing nonlinear inversions of the images with minimal manual interaction in the optimization process. The tool utilizes the NOMAD mixed variable optimization tool to perform the optimization.

97 MATHEMATICS AND COMPUTING↗