Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESISTANCE DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Design and fabrication of a CMOS-compatible MHP gas sensor

A novel micro-hotplate (MHP) gas sensor is designed and fabricated with a standard CMOS technology followed by post-CMOS processes. The tungsten plugging between the first and the second metal layer in the CMOS processes is designed as zigzag resistor heaters embedded in the membrane. In the post-CMOS processes, the membrane is released by front-side bulk silicon etching, and excellent adiabatic performance of the sensor is obtained. Pt/Ti electrode films are prepared on the MHP before the coating of the SnO{sub 2} film, which are promising to present better contact stability compared with Al electrodes. Measurements show that at room temperature in atmosphere, the device has a low power consumption of ∼19 mW and a rapid thermal response of 8 ms for heating up to 300 °C. The tungsten heater exhibits good high temperature stability with a slight fluctuation (<0.3%) in the resistance at an operation temperature of 300 °C under constant heating mode for 336 h, and a satisfactory temperature coefficient of resistance of about 1.9‰/°C.

36 MATERIALS SCIENCE↗

Impact of barrier thickness on transistor performance in AlN/GaN high electron mobility transistors grown on free-standing GaN substrates

A series of six ultrathin AlN/GaN heterostructures with varied AlN thicknesses from 1.5–6 nm have been grown by molecular beam epitaxy on free-standing hydride vapor phase epitaxy GaN substrates. High electron mobility transistors (HEMTs) were fabricated from the set in order to assess the impact of barrier thickness and homo-epitaxial growth on transistor performance. Room temperature Hall characteristics revealed mobility of 1700 cm{sup 2}/V s and sheet resistance of 130 Ω/□ for a 3 nm thick barrier, ranking amongst the lowest room-temperature sheet resistance values reported for a polarization-doped single heterostructure in the III-Nitride family. DC and small signal HEMT electrical characteristics from submicron gate length HEMTs further elucidated the effect of the AlN barrier thickness on device performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Short-wavelength interband cascade infrared photodetectors operating above room temperature

High temperature operation (250–340 K) of short-wavelength interband cascade infrared photodetectors (ICIPs) with InAs/GaSb/Al 0.2 In 0.8 Sb/GaSb superlattice absorbers has been demonstrated with a 50% cutoff wavelength of 2.9 μm at 300 K. Two ICIP structures, one with two and the other with three stages, were designed and grown to explore this multiple-stage architecture. At λ = 2.1 μm, the two- and three-stage ICIPs had Johnson-noise-limited detectivities of 5.1 × 10 9 and 5.8 ×10 9 cm Hz 1/2 /W, respectively, at 300 K. The better device performance of the three-stage ICIP over the two-stage ICIP confirmed the advantage of more stages for this cascade architecture. Furthermore, an Arrhenius activation energy of 450 meV is extracted for the bulk resistance-area product, which indicates the dominance of the diffusion current at these high temperatures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

First-principles calculations reveal controlling principles for carrier mobilities in semiconductors

It has long been believed that carrier mobilities in semiconductors can be calculated by Fermi s golden rule (Born approximation). Phenomenological models for scattering amplitudes are typically used for engineering- level device modeling. Here we introduce a parameter-free, first-principles approach based on complex- wavevector energy bands that does not invoke the Born approximation. We show that phonon-limited mobility is controlled by low-resistivity percolation paths and that in ionized-impurity scattering one must account for the effect of the screening charge, which cancels most of the Coulomb tail.Finally, calculated electron mobilities in silicon are in agreement with experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Emergent Inductance from Chiral Orbital Currents in a Bulk Ferrimagnet

Here, we report the discovery of a new form of inductance in the bulk ferrimagnet Mn 3 ⁢Si 2 ⁢Te 6 , which features strong spin-orbit coupling, large magnetic anisotropy, and pronounced magnetoelastic interactions. Below its Curie temperature (𝑇 𝐶 ≈ 78 K), Mn 3 ⁢Si 2 ⁢Te 6 hosts chiral orbital currents (COC) that circulate within the crystal lattice and give rise to collective electronic behavior [Control of chiral orbital currents in a colossal magnetoresistance material, Nature (London) 611, 467 (2022).]. By applying a magnetic field along the hard 𝑐 axis and driving the system with low-frequency currents, we uncover a giant inductive response up to millhenry scale, originating from first-order reconfigurations of COC domains. These domains act as coherent mesoscopic inductive elements that resist reversal upon current reduction, producing a large electromotive force and sharply increasing voltage. This emergent inductance defies classical models, occurs without superconductivity or engineered nanostructures, and opens a new frontier in orbital-based quantum functionality and device concepts.

complex materials↗

Fabrication of a glancing-angle-deposited distributed polarization rotator for ultraviolet applications

Glancing-angle–deposited thin films are used to fabricate half-wave plates in a 1-D striped geometry, forming alternating regions of linearly polarized light on a single 100-mm-diam substrate. MgO is selected for fabricating the birefringent films for use in vacuum, based on its formation of isolated columns that avoid potential tensile-stress failure of the porous film. While large-area tests have shown high defect densities for fluences <10 J/cm 2 , small-spot laser-damage testing has shown resistance to fluences up to 30 J/cm 2 (351-nm, 5-ns pulse). Here, an amorphous silica film is investigated to match the optical thickness in the intermediate regions in an effort to fabricate a polarization-control device to reduce focal-point modulation (“beam smoothing”) in high-intensity laser systems. Ongoing efforts to improve the laser-damage threshold and minimize optical losses caused by scatter are essential to realizing a practical device. Scalability of the process to meter-scale substrates is also explored.

47 OTHER INSTRUMENTATION↗

DEVELOPMENT OF A TAMPER RESISTANT/INDICATING AEROSOL COLLECTION SYSTEM FOR ENVIRONMENTAL SAMPLING AT BULK HANDLING FACILITIES

Environmental sampling has become a key component of International Atomic Energy Agency (IAEA) safeguards approaches since its approval for use in 1996. Environmental sampling supports the IAEA's mission of drawing conclusions concerning the absence of undeclared nuclear material or nuclear activities in a Nation State. Swipe sampling is the most commonly used method for the collection of environmental samples from bulk handling facilities. However, augmenting swipe samples with an air monitoring system, which could continuously draw samples from the environment of bulk handling facilities, could improve the possibility of the detection of undeclared activities. Continuous sampling offers the opportunity to collect airborne materials before they settle onto surfaces which can be decontaminated, taken into existing duct work, filtered by plant ventilation, or escape via alternate pathways (i.e. drains, doors). Researchers at the Savannah River National Laboratory and Oak Ridge National Laboratory have been working to further develop an aerosol collection technology that could be installed at IAEA safeguarded bulk handling facilities. The addition of this technology may reduce the number of IAEA inspector visits required to effectively collect samples. The principal sample collection device is a patented Aerosol Contaminant Extractor (ACE) which utilizes electrostatic precipitation principles to deposit particulates onto selected substrates. Recent work has focused on comparing traditional swipe sampling to samples collected via an ACE system, and incorporating tamper resistant and tamper indicating (TRI) technologies into the ACE system. Development of a TRI-ACE system would allow collection of samples at uranium/plutonium bulk handling facilities in a manner that ensures sample integrity and could be an important addition to the international nuclear safeguards inspector's toolkit. This work was supported by the Next Generation Safeguards Initiative (NGSI), Office of Nonproliferation and International Security (NIS), National Nuclear Security Administration (NNSA).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Novel Technology for Complex Rheological Measurements - 16471

As the UK nuclear industry embarks on a second phase of nuclear power generation, the industry is faced with numerous sludge and slurry challenges associated with the decommissioning and clean-up of historical nuclear sites. The remediation of Sellafield, the largest nuclear site in the UK, is anticipated to cost GBP 53 bn over the next 100 years. Substantial cost is associated with the clean-up, transfer and safe storage of legacy particulate wastes encountered in ponds, silos, highly active storage tanks and many more large tanks on site. To develop suitable design strategies for the mobilization and transfer of sludge, the rheology of the sludge should be accurately determined. The current work demonstrates the use of a Quartz Crystal Microbalance to measure sludge rheology, specifically the shear yield stress. The device is simple to operate with no mechanical parts, small and portable enabling deployment into limited access areas, and eliminates the need for operator sampling and laboratory measurement. The measurement principle relates to the resonance frequency and motional resistance of a piezo-electric sensor as the sensor is submerged in the desired test material. The air-to-sample frequency and resistance shifts are shown to correlate with the shear yield stress of the suspension as measured by conventional vane viscometry. As the particle network stiffens (increased yield stress), the sensor motional resistance and its resonant frequency become more positive. These characteristic responses and their correlation to the shear yield stress have been confirmed for a range of particle suspensions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nanoscale Control of Oxygen Defects and Metal–Insulator Transition in Epitaxial Vanadium Dioxides

Strongly correlated vanadium dioxide (VO 2 ) is one of the most promising materials that exhibits a temperature-driven, metal–insulator transition (MIT) near room temperature. The ability to manipulate the MIT at nanoscale offers both insight into understanding the energetics of phase transition and a promising potential for nanoelectronic devices. In this work, we study nanoscale electrochemical modifications of the MIT in epitaxial VO 2 thin films using a combined approach with scanning probe microscopy (SPM) and theoretical calculations. We find that applying electric voltages of different polarity through an SPM tip locally changes the contact potential difference and conductivity on the surface of VO 2 by modulating the oxygen stoichiometry. We observed nearly 2 orders of magnitude change in resistance between positive and negative biased-tip written areas of the film, demonstrating the electric field modulated MIT behavior at the nanoscale. Density functional theory calculations, benchmarked against more accurate many-body quantum Monte Carlo calculations, provide information on the formation energetics of oxygen defects that can be further manipulated by strain. In conclusion, this study highlights the crucial role of oxygen vacancies in controlling the MIT in epitaxial VO 2 thin films, useful for developing advanced electronic and iontronic devices.

36 MATERIALS SCIENCE↗

Non-Uniform Dose Mapping Controlled by Modulated Vertical and Horizontal Scans

Since geometries of semi-conductor devices continue to shrink, the requirement for each process becomes severer to keep uniformity of electrical parameters of the semi-conductor devices. A larger wafer also causes larger variations. Thus it has been strongly required for ion implantation process to compensate for the variations from other processes because of its good dose controllability. A newly developed mapping of intentional non-uniform dosage system, which is named 'MIND system', is implemented in SEN's single-wafer-type implanters. The MIND system controls both horizontal and vertical scan speed simultaneously. Intentional two-dimensional non-uniform profiles of sheet resistance, such as concentric and eccentric profiles, are obtained only by single-step ion implantation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Analysis of an anti-reflecting nanowire transparent electrode for solar cells

Transparent electrodes are an important component in many optoelectronic devices, especially solar cells. In this study, we investigate a nanowire transparent electrode that also functions as an anti-reflection coating for silicon solar cells, taking into account the practical constraints that the electrode is typically encapsulated and needs to be in electric contact with the semiconductor. Numerical simulations show that the electrode can provide near-perfect broadband anti-reflection over much of the frequency range above the silicon band gap for both polarizations while keeping the sheet resistance sufficiently low. To provide insights into the physics mechanism of this broadband anti-reflection, we introduce a generalized Fabry–Perot model, which captures the effects of the higher order diffraction channels as well as the modification of the reflection coefficient of the interface introduced by the nanowires. This model is validated using frequency-domain electromagnetic simulations. Finally, our work here provides design guidelines for nanowire transparent electrode in a device configuration that is relevant for solar cell applications.

14 SOLAR ENERGY↗

Stability of CIGS Solar Cells and Component Materials Evaluated by a Step-Stress Accelerated Degradation Test Method: Preprint

A step-stress accelerated degradation testing (SSADT) method was employed for the first time to evaluate the stability of CuInGaSe2 (CIGS) solar cells and device component materials in four Al-framed test structures encapsulated with an edge sealant and three kinds of backsheet or moisture barrier film for moisture ingress control. The SSADT exposure used a 15 degrees C and then a 15% relativehumidity (RH) increment step, beginning from 40 degrees C/40%RH (T/RH = 40/40) to 85 degrees C/70%RH (85/70) as of the moment. The voluminous data acquired and processed as of total DH = 3956 h with 85/70 = 704 h produced the following results. The best CIGS solar cells in sample Set-1 with a moisture-permeable TPT backsheet showed essentially identical I-V degradation trend regardless of theAl-doped ZnO (AZO) layer thickness ranging from standard 0.12 um to 0.50 um on the cells. No clear 'stepwise' feature in the I-V parameter degradation curves corresponding to the SSADT T/RH/time profile was observed. Irregularity in I-V performance degradation pattern was observed with some cells showing early degradation at low T/RH < 55/55 and some showing large Voc, FF, and efficiency degradation due to increased series Rs (ohm-cm2) at T/RH = 70/70. Results of (electrochemical) impedance spectroscopy (ECIS) analysis indicate degradation of the CIGS solar cells corresponded to increased series resistance Rs (ohm) and degraded parallel (minority carrier diffusion/recombination) resistance Rp, capacitance C, overall time constant Rp*C, and 'capacitor quality' factor (CPE-P), whic were related to the cells' p-n junction properties. Heating at 85/70 appeared to benefit the CIGS solar cells as indicated by the largely recovered CPE-P factor. Device component materials, Mo on soda lime glass (Mo/SLG), bilayer ZnO (BZO), AlNi grid contact, and CdS/CIGS/Mo/SLG in test structures with TPT showed notable to significant degradation at T/RH = 70/70. At T/RH = 85/70, substantial blistering of BZO layers on CIGS cell pieces was observed that was not seen on BZO/glass, and a CdS/CIGS sample displayed a small darkening and then flaking feature. Additionally, standard AlNi grid contact was less stable than thin Ni grid contact at T/RH = 70/70. The edge sealant and moisture-blocking films were effective to block moisture ingress, as evidenced by the good stability of most CIGS solar cells and device components at T/RH = 85/70 for 704 h, and by preservation of the initial blue color on the RH indicator strips. The SSADT experiment is ongoing to be completed at T/RH = 85/85.

14 SOLAR ENERGY↗

Unconventional unidirectional magnetoresistance in heterostructures of a topological semimetal and a ferromagnet

Unidirectional magnetoresistance (UMR) in a bilayer heterostructure, consisting of a spin-source material and a magnetic layer, refers to a change in the longitudinal resistance on the reversal of magnetization and originates from the interaction of non-equilibrium spin accumulation and magnetization at the interface. Since the spin polarization of an electric-field-induced non-equilibrium spin accumulation in conventional spin-source materials is restricted to be in the film plane, the ensuing UMR can only respond to the in-plane component of magnetization. However, magnets with perpendicular magnetic anisotropy are highly desired for magnetic memory and spin-logic devices, whereas the electrical read-out of perpendicular magnetic anisotropy magnets through UMR is critically missing. Here, in this study, we report the discovery of an unconventional UMR in the heterostructures of a topological semimetal (WTe 2 ) and a perpendicular magnetic anisotropy ferromagnetic insulator (Cr 2 Ge 2 Te 6 ), which allows to electrically read the up and down magnetic states of the Cr 2 Ge 2 Te 6 layer through longitudinal resistance measurements.

Kao, I-Hsuan [Carnegie Mellon Univ., Pittsburgh, P↗

Improved performance of dye-sensitized solar cells with surface-treated TiO{sub 2} as a photoelectrode

We report on the effects of surface-modified TiO{sub 2} on the performance of dye-sensitized solar cells (DSSCs). TiO{sub 2} surface was modified with Na{sub 2}CO{sub 3} via a simple dip coating process and the modified TiO{sub 2} was applied to photoelectrodes of DSSCs. By dipping of TiO{sub 2} layer into aqueous Na{sub 2}CO{sub 3} solution, the DSSC showed a power conversion efficiency of 9.98%, compared to that (7.75%) of the reference device without surface treatment. The UV–vis absorption spectra, the impedance spectra and the dark current studies revealed that the increase of all parameters was attributed to the enhanced dye adsorption, the prolonged electron lifetime and the reduced interfacial resistance.

36 MATERIALS SCIENCE↗

High voltage and high current density vertical GaN power diodes

We report on the realization of a GaN high voltage vertical p-n diode operating at > 3.9 kV breakdown with a specific on-resistance < 0.9 mΩ.cm 2 . Diodes achieved a forward current of 1 A for on-wafer, DC measurements, corresponding to a current density > 1.4 kA/cm 2 . An effective critical electric field of 3.9 MV/cm was estimated for the devices from analysis of the forward and reverse current-voltage characteristics. Furthermore this suggests that the fundamental limit to the GaN critical electric field is significantly greater than previously believed.

30 DIRECT ENERGY CONVERSION↗

Suppression of edge-localized modes by magnetic field perturbations

Transport bursts in simulations of edge-localized modes (ELMs) in tokamaks are suppressed by the application of magnetic field perturbations. The amplitude of the applied magnetic field perturbations is characterized by a stochasticity parameter S. When S>1, magnetic flux surfaces are destroyed and the magnetic field lines diffuse in minor radius. As S increases in the simulations, the magnitude of the ELM bursts decreases. The size of bursts is reduced to a very small value while S is still less than unity and most of the magnetic flux surfaces are still preserved. Magnetic field line stochasticity is not a requirement for the stabilization of ELMs by the magnetic field perturbations. The magnetic field perturbations act by suppressing the growth of the resistive ballooning instability that underlies the ELM bursts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pressure driven tearing and interchange modes in the reversed field pinch

In this work, the magneto-hydro-dynamic stability of pressure driven modes in the reversed field pinch has been analyzed. It is shown that at low and intermediate {beta}'s, i.e., typically for values below 20-25%, the tearing parity is dominant, while only at very high {beta}, well above the achieved experimental values, at least part of the modes are converted to ideal interchange instabilities. Before their transition to ideal instabilities, according to their Lundquist number scaling, they can be classified as resistive-g modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of equilibrium field coil misalignments on the divertor footprints in NSTX-U

The presence of error fields in a tokamak device is inevitable, so it is of fundamental importance to understand their impact on the operation of the device and therefore up to what level they can be tolerated. In this paper a prediction of the impact on the magnetic footprints on the divertor plates due to the misalignment of NSTX-U equilibrium coils is presented. Resistive MHD solutions are used to predict the magnetic field perturbations experienced by the field lines due to the presence of error fields. A linear relation between the magnitude of the misalignment and the area of the magnetic footprints is found, as well as an inverse proportionality between the size of a magnetic footprint and the plasma penetration of the field lines composing the footprint. This study is intended as a starting point in the process of investigating divertor footprints associated with the plasma response to intrinsic error fields with resistive MHD codes. A basic interpretation of the results suggests that large footprints resulting from equilibrium coils misalignment may be desirable, to some extent, to decrease the peak heat load on the divertor components. Lastly, a more complete interpretation of the results presented here will involve a number of complex physics issues, for example pedestal transport and stability along with the role of various scrape-off layer and divertor processes, as well as experimental data to confirm the predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗