Search NASA⌕ Search

SEARCH · Search NASA

Results for “acceleration factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Subsonic flight test evaluation of a performance seeking control algorithm on an F-15 airplane

The subsonic flight test evaluation phase of the NASA4 F-15 (powered by F100 engines) performance-seeking control program was completed for single-engine operation at part- and military-power settings. The subsonic performance-seeking control algorithm optimizes the quasi-steady-state performance of the propulsion system for three modes of operation: the minimum-fuel-flow mode, the minimum-temperature mode, and the maximum-thrust mode. Decreases in thrust-specific fuel consumption of 1 to 2 percent were measured in the minimum-fuel-flow mode; these fuel savings are significant especially for supersonic cruise aircraft. Decreases of up to approximately 100 R in fan turbine inlet temperature were measured in the minimum-temperature mode. Temperature reductions of this magnitude would more than double turbine life if inlet temperature was the only life factor. Measured thrust increases of up to approximately 15 percent in the maximum-thrust mode cause substantial increases in aircraft acceleration. The subsonic flight phase has validated the performance-seeking control technology which can significantly benefit the next generation of fighter and transport aircraft.

Gilyard, Glenn B.↗

Pair cascades in extragalactic jets. 1: Gamma rays

A model of the approximately 0.1-10 GeV gamma-ray jets observed by the EGRET instrument on the Compton Gamma Ray Observatory (CGRO) is developed. It is shown that the soft X-ray background in an active galactic nuclei (AGN) contributes an opacity to pair production and that a gamma-ray photosphere or 'gamma-sphere' can be defined whose radius increases with gamma-ray energy E(sub gamma). It is proposed that the observed gamma-ray emission is due to inverse Compton scattering of the ambient soft X-rays by relativistic pairs accelerated in situ by shock fronts in a relativistic jet. For a wide range of assumed physical conditions, the emission at a given E(sub gamma) originates from near the associated gamma-spheres; emission from below the gamma-sphere initiates a cascade down to the energy where the gamma-rays can escape freely. In this model, the slope of the emergent gamma-ray spectrum is determined by the scattered, soft X-ray spectrum and the variation of the particle acceleration rate with jet radius. In general it is expected that the variation in the gamma-ray flux will be either slower or later at higher energy. It is also shown that the efficiency of conversion of energy from injected high-energy pairs to 0.1-10 GeV gamma-rays is typically high so that the models are radiatively efficient. It is argued that the observed gamma-ray jets are likely to be particle-dominated, though magnetically confined. The gamma-ray spectrum should continue down to an energy approximately 5 MeV emitted from an annihilation radius within which the pair content of the jet is limited by annihilation. This is probably the site of the beamed hard X-ray emission. It is speculated that the relativistic jets associated with radio-loud AGNs are powered electromagnetically by a spinning black hole and that they are collimated by an encircling MHD wind leaving the accretion disk at a slower speed. Powerful FR2 radio sources are formed when the hole spins rapidly and the relativistic core accelerates the MHD sheath; low-power FR1 sources ensue when the opposite occurs. Finally, it is suggested that the key factor which determines whether or not a given active nucleus can form a jet and a radio to gamma-ray nonthermal continuum is the central density of mass-losing stars which, when large, precludes the formation of a super-Alfvenic, collimating wind.

Blandford, R. D.↗

May 4, 1998 Storm: Observations of Energetic Ion Composition by POLAR

A major geomagnetic storm occurred at 5:00-12:05 UT on May 4, 1998. During this period, the magnetosphere was compressed and eroded; POLAR traveled in its outbound orbit from the equatorial radiation belt to the cusp and crossed the magnetopause into the magnetosheath. Two CEP-like (Cusp Energetic Particle) events with two to three orders of magnitudes enhancements of MeV ion fluxes were measured. The first event had a peak flux higher than that of the intense outer radiation belt in the equatorial plane. The shape of the measured energy spectra (in the unit of keV/e) were ion species dependent. For He+/He++ ratio at 18-269 keV/e, the difference between the radiation belt and the magnetosheath can be by a factor of as large as 62. In the magnetosheath, the 18-269 keV/e ion composition are variable, indicating a mass dependent acceleration process. These MeV ions may be energized by a mechanism in the cusp responsible for the CEP events previously reported.

Chen, Jiasheng↗

Training to Enhance Design Team Performance: A Cure for Tunnel Vision

Design Team performance is a function of the quality and degree of academic training and the cumulative, learned experience of the individual members of the team. Teamwork, leadership, and communications certainly are factors that affect the measure of the performance of the team, but they are not addressed here. This paper focuses on accelerating the learned experience of team members and describes an organizational approach that can significantly increase the effective experience level for any engineering design team. The performance measure of the whole team can be increased by increasing the engineering disciplines' cross awareness of each other and by familiarizing them with their affect at the system level. Discipline engineers know their own discipline well, but typically are not intimately familiar with their technical interaction with and dependencies on all the other disciplines of engineering. These dependencies are design integration functions and are worked out well by the discipline engineers as long as they are involved in the design of types of systems that they have experience with.

Parker, James W.↗

The Supercritical Pile GRB Model: The Prompt to Afterglow Evolution

The "Supercritical Pile" is a very economical GRB model that provides for the efficient conversion of the energy stored in the protons of a Relativistic Blast Wave (RBW) into radiation and at the same time produces - in the prompt GRB phase, even in the absence of any particle acceleration - a spectral peak at energy approx. 1 MeV. We extend this model to include the evolution of the RBW Lorentz factor Gamma and thus follow its spectral and temporal features into the early GRB afterglow stage. One of the novel features of the present treatment is the inclusion of the feedback of the GRB produced radiation on the evolution of Gamma with radius. This feedback and the presence of kinematic and dynamic thresholds in the model can be the sources of rich time evolution which we have began to explore. In particular. one can this may obtain afterglow light curves with steep decays followed by the more conventional flatter afterglow slopes, while at the same time preserving the desirable features of the model, i.e. the well defined relativistic electron source and radiative processes that produce the proper peak in the (nu)F(sub nu), spectra. In this note we present the results of a specific set of parameters of this model with emphasis on the multiwavelength prompt emission and transition to the early afterglow.

Mastichiadis, A.↗

A Bulk Comptonization Model for the Prompt GRM Emission

The "Supercritical Pile" is a very economical GRB model that provides for the efficient conversion of the energy stored in the protons of a Relativistic Blast Wave (RBW) into radiation and at the same time produces - in the prompt GRB phase, even in the absence of any particle acceleration - a spectral peak at energy approximately 1 MeV. We extend this model to include the evolution of the RBW Lorentz factor F and thus follow its spectral and temporal features into the early GRB afterglow stage. One of the novel features of the present treatment is the inclusion of the feedback of the GRB produced radiation on the evolution of Gamma with radius. This feedback and the presence of kinematic and dynamic thresholds in the model are sources of potentially very rich time evolution which we have began to explore. In particular, one can this way obtain afterglow light curves with steep decays followed by the more conventional flatter afterglow slopes, while at the same time preserving the desirable features of the model, i.e. the well defined relativistic electron source and radiative processes that produce the proper peak in the nu F(sub nu) spectra. In this note we present the results of a specific set of parameters of this model with emphasis on the multiwavelength prompt emission and transition to the early afterglow.

Kazanas, Demos↗

Juno Gravity Science: Preparing for Data Collection at Jupiter

One of the primary goals of the Juno mission is to investigate Jupiter’s interior by mapping its gravitational field with the gravity science instrument. The Juno spacecraft has two radio science components that comprise the gravity science instrument: the X-band telecommunications system for a X-up/X-down link and a Ka-band Translator for a Ka-up/Ka-down link. The Deep Space Network’s DSS-25 beam waveguide antenna at the Goldstone Deep Space Communications Complex in California provides the X- and Ka-band uplink alongside an Advanced Water Vapor Radiometer to calibrate tropospheric effects. X-band and Ka-band downlink data are collected with both open-loop and closed-loop receivers located at the complex. Utilization of Ka-band provides scientific benefit to the Doppler measurements, but also adds operational challenges. Pointing of the uplink and downlink Ka-band signals requires additional systems to be calibrated and operated by the Deep Space Network; and the higher frequency of Ka-band means the signal dynamics are increased by a factor of four over X-band signals. Due to the spacecraft’s elliptical orbit and 4000 kilometer perijove altitude, it accelerates at an extreme rate as it approaches Jupiter, inducing large dynamic ranges in Doppler range of approximately 6 MHz over 3 hours at Ka-band. After the installation of a new Ka-band transmitter at DSS-25 for Juno was completed in 2015, end-to-end testing was conducted to ensure readiness for operations at Jupiter and provide an initial assessment of the performance. Cruise testing was conducted in the same operational configuration that the system will be used in during perijove passes. Processed open-loop data yielded uncalibrated Doppler residuals of 1.9 mHz at X-band and 6.0 mHz at Ka-band with 5-second compression time. Conduction of these tests has prepared the instrument and the operations team for science data collection during the science phase of the mission.

Buccino, Dustin↗

Degradation in PV Encapsulation Strength of Attachment: An Interlaboratory Study Towards a Climate-Specific Test

Reduced strength of attachment of the encapsulant resulting from the outdoor environment, including ultraviolet (UV) radiation, may decrease photovoltaic (PV) module lifetime by enabling widespread corrosion of internal components. To date, few studies exist showing how the adhesion of PV components varies with environmental stress. We have conducted an interlaboratory experiment to provide an understanding that will be used to develop climatic specific module tests. Factors examined in the study included the UV light source (lamp type), temperature, and humidity to be proposed for use in accelerated aging tests. A poly (ethylene-co-vinyl acetate) (EVA) formulation often used in veteran PV installations was studied using a compressive shear test - to quantify the strength of attachment at the EVA/glass interface. Replicate laminated glass/polymer/glass coupon specimens were weathered at 12 institutions using a variety of indoor chambers or field aging. Shear strength, shear strain, and toughness were measured using a mechanical load-frame for the compressive shear test, with subsequent optical imaging and electron microscopy of the separated surfaces.

14 SOLAR ENERGY↗

The Effect of an Oxide Layer on Resistive-Wall Wakefields

Shorter and shorter electron bunches are now used in the FEL designs. The fine structure of the wall of a beam vacuum pipe plays more noticeable role in the wake field generation. Additionally to the resistance and roughness, the wall may have an oxide layer, which is usually a dielectric. It is important for aluminium pipe, which have Al2O3 layer. The thickness of this layer may vary in a large range: 1-100 nm. We study this effect for the very short (20-1000 nm) ultra relativistic bunches in an infinite round pipe. We solved numerically the Maxwell equations for the fields in the metal and ceramics. Results showed that the oxide layer may considerably increase the wavelength and the decay time of the resistive-wall wake fields, however the loss factor of the very short bunches does not change much.

43 PARTICLE ACCELERATORS↗

A Method for In-Situ Q₀ Measurements of High-Quality SRF Resonators

Accelerator projects such as LCLS-II naturally require low-loss superconducting (SRF) cavities. Due to strong demand for improving intrinsic quality factor (Q₀), importance of accurate cavity characterization increases. We propose a method to measure Q₀ in situ for an SRF resonator installed in its cryogenic module and connected with a RF feed source via a fixed RF coupler. The method exploits measurements of a response for an SRF resonator fed by an amplitude-modulated signal. Such a signal can be synthesized as a beat-wave composed of two frequencies that are close to the resonant frequency. Analyzing the envelope of the reflected signal, one can find the difference in reflection for the chosen frequencies and use them to compute the intrinsic Q. We also develop the methodology to carry out measurements of Q₀ at the nominal cavity operating voltage. We verified our method in experiments with a room temperature copper resonator and with two SRF resonators including Fermilab’s 650 MHz cavity and JLab’s 1500 MHz cavity.

43 PARTICLE ACCELERATORS↗

Operator-level quantum acceleration of non-logconcave sampling

Sampling from probability distributions of the form 𝝈 ∝ e −𝜷V , where V is a continuous potential, is a fundamental task across physics, chemistry, biology, computer science, and statistics. However, when V is nonconvex, the resulting distribution becomes non-logconcave, and classical methods such as Langevin dynamics often exhibit poor performance. We introduce a quantum algorithm that provably accelerates a broad class of continuous-time sampling dynamics. For Langevin dynamics, our method encodes the target Gibbs measure into the amplitudes of aquantum state, identified as the kernel of a block matrix derived from a factorization of the Witten Laplacian operator. This connection enables Gibbs sampling via singular value thresholding and yields up to a quartic quantum speedup over best-knownclassical Langevin-based methods in the non-logconcave setting. Building on this framework, we further develop the first quantum algorithm that accelerates replica exchange Langevin diffusion, a widely used method for sampling from complex, rugged energy landscapes.

97 MATHEMATICS AND COMPUTING↗

Developing The Physics Desing for NDCS-II, A Unique Pulse-Compressing Ion Accelerator

The Heavy Ion Fusion Science Virtual National Laboratory (a collaboration of LBNL, LLNL, and PPPL) is using intense ion beams to heat thin foils to the 'warm dense matter' regime at {approx}< 1 eV, and is developing capabilities for studying target physics relevant to ion-driven inertial fusion energy. The need for rapid target heating led to the development of plasma-neutralized pulse compression, with current amplification factors exceeding 50 now routine on the Neutralized Drift Compression Experiment (NDCX). Construction of an improved platform, NDCX-II, has begun at LBNL with planned completion in 2012. Using refurbished induction cells from the Advanced Test Accelerator at LLNL, NDCX-II will compress a {approx}500 ns pulse of Li{sup +} ions to {approx} 1 ns while accelerating it to 3-4 MeV over {approx} 15 m. Strong space charge forces are incorporated into the machine design at a fundamental level. We are using analysis, an interactive 1D PIC code (ASP) with optimizing capabilities and centroid tracking, and multi-dimensional Warpcode PIC simulations, to develop the NDCX-II accelerator. This paper describes the computational models employed, and the resulting physics design for the accelerator.

43 PARTICLE ACCELERATORS↗

Space-Charge Simulation of Integrable Rapid Cycling Synchrotron

Integrable optics is an innovation in particle accelerator design that enables strong nonlinear focusing without generating parametric resonances. We use the Synergia tracking code to investigate the application of integrable optics to high-intensity hadron rings. We consider an integrable rapid-cycling synchrotron (iRCS) designed to replace the Fermilab Booster. We find that incorporating integrability into the design suppresses the beam halo generated by a mismatched KV beam. Our iRCS design includes other features of modern ring design such as low momentum compaction factor and harmonically canceling sextupoles. Experimental tests of high-intensity beams in integrable lattices will take place over the next several years at the Fermilab Integrable Optics Test Accelerator (IOTA) and the University of Maryland Electron Ring (UMER).

43 PARTICLE ACCELERATORS↗

VipariNama: RNA viral vectors to rapidly elucidate the relationship between gene expression and phenotype

Synthetic transcription factors have great promise as tools to help elucidate relationships between gene expression and phenotype by allowing tunable alterations of gene expression without genomic alterations of the loci being studied. However, the years-long timescales, high cost, and technical skill associated with plant transformation have limited their use. In this work, we developed a technology called VipariNama (ViN) in which vectors based on the tobacco rattle virus are used to rapidly deploy Cas9-based synthetic transcription factors and reprogram gene expression in planta. We demonstrate that ViN vectors can implement activation or repression of multiple genes systemically and persistently over several weeks in Nicotiana benthamiana, Arabidopsis (Arabidopsis thaliana), and tomato (Solanum lycopersicum). By exploring strategies including RNA scaffolding, viral vector ensembles, and viral engineering, we describe how the flexibility and efficacy of regulation can be improved. We also show how this transcriptional reprogramming can create predictable changes to metabolic phenotypes, such as gibberellin biosynthesis in N. benthamiana and anthocyanin accumulation in Arabidopsis, as well as developmental phenotypes, such as plant size in N. benthamiana, Arabidopsis, and tomato. These results demonstrate how ViN vector-based reprogramming of different aspects of gibberellin signaling can be used to engineer plant size in a range of plant species in a matter of weeks. In summary, ViN accelerates the timeline for generating phenotypes from over a year to just a few weeks, providing an attractive alternative to transgenesis for synthetic transcription factor-enabled hypothesis testing and crop engineering.

59 BASIC BIOLOGICAL SCIENCES↗

Factors that influence the activity of biomass-degrading enzymes in the presence of ionic liquids—a review

Ionic liquids (ILs) are seen as a more sustainable alternative to volatile organic solvents that are accelerating innovations in many industries such as energy storage, separations, and bioprocessing. The ability to effectively deconstruct lignocellulosic biomass is a significant hurdle in the biorefining/bioprocessing industry and presents limitations towards the commercial production of bioproducts (such as biofuels, biomaterials, etc. ). Certain ILs have been shown to promote effective lignin removal, cellulose recovery, and sugar yields from various biomass feedstocks such as corn stover, wheat straw, sugarcane bagasse, sorghum, switchgrass, miscanthus, poplar, pine, eucalyptus, and certain mixtures of municipal solid waste. However, these improvements are often counteracted by the limited biocompatibility of ILs, which results in an IL-induced reduction in enzyme activity and stability—an important downstream step in the conversion of biomass to biofuels/bioproducts. As a result, significant efforts have been made to discover and engineer compatible enzyme-IL systems and to improve our understanding on the effect that these ILs have on these systems. This review seeks to examine the impact of ionic liquids on enzymes involved in lignocellulosic biomass deconstruction, with a specific focus on their relevance in the context of pretreatment. Beyond presenting an overview of the ionic liquid pretreatment landscape, we outline the main factors that influence enzyme activity and stability in the presence of ILs This data is consolidated and analyzed to apply this body of knowledge towards new innovations that could lead to improvements in the processing of biomass to biofuels and bioproducts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heat load of a P-doped GaAs photocathode in SRF electron gun

Many efforts were made over the last decades to develop a better polarized electron source for the high energy physics. Several laboratories operate DC guns with the Gallium-Arsenide photo-cathode, which yield a highly polarized electron beam. However, the beam's emittance might well be improved using a Superconducting RF electron gun, which delivers beams of higher brightness than DC guns does, because the field gradient at the cathode is higher. SRF guns with metal cathodes and CsTe cathodes have been tested successfully. To produce polarized electrons, a Gallium-Arsenide photo-cathode must be used: an experiment to do so in a superconducting RF gun is under way at BNL. Since the cathode will be normal conducting, the problem about the heat load stemming from the cathode arises. We present our measurements of the electrical resistance of GaAs at cryogenic temperatures, a prediction of the heat load and the verification by measuring the quality factor of the gun with and without cathode.

43 PARTICLE ACCELERATORS↗

Measured vs. Calculated Dose Rates During Ring Injection Dump Replacement

One of the most irradiated Spallation Neutron Source (SNS) accelerator components is the ring injection dump (RID), which is located downstream of the accumulator ring injection section. The unstripped and only partially stripped H - beam, about 5% of the full SNS beam current, is discarded in the injection into the accumulator ring and is redirected to the RID. According to the accelerator operation plan, the beam stop and the window assemblies of the existing RID are removed and replaced when they have reached their end-of-life owing to radiation exposure. This procedure, which includes multiple steps, took place during a facility maintenance period in March 2023. To support work planning and meet as low as reasonably achievable (ALARA) requirements during removal and exchange of the components, dose rates were calculated for each stage of the exchange operation. During each stage, dose rates were measured before and after work. This comparison shows that measured dose rates are within a factor of 2 of the predicted (calculated) dose rates.

43 PARTICLE ACCELERATORS↗

Cross-section measurement and analysis for the {sup 149}Sm(n,alpha){sup 146}Nd reaction at 6.0 MeV

We have measured the {sup 149}Sm(n,alpha){sup 146}Nd cross section at 6.0 MeV to be 0.12+-0.018 mb. This is the first reported result for this cross section in the MeV region and so should be helpful for constraining nuclear data evaluations (which differ by a factor of 40 for this reaction at this energy) and for testing and improving nuclear models. The experiment was performed at the at the 4.5-MV Van de Graaff accelerator of Peking University. Neutrons were produced via the {sup 2}H(d,n){sup 3}He reaction using a deuterium gas target, and absolute neutron flux was determined with a small {sup 238}U fission chamber. Alpha particles were detected using a two-section gridded ionization chamber in which two large-area {sup 149}Sm{sub 2}O{sub 3} samples were placed back-to-back so that the cross section and forward/backward ratio were measured for nearly the entire 4pi solid angle. The data were compared to statistical-model predictions using the code talys. Good agreement between the measured and theoretical cross sections could be obtained with a small modification of the alpha-optical potential parameters from their default values in talys. However, we were not able to reproduce the measured forward/backward ratio. In addition, using the previously reported {sup 147}Sm(n,alpha){sup 144}Nd cross section at 6.0 MeV together with our new result, good agreement was found between the measured and predicted cross-section ratio for these two isotopes. Finally, none of the existing evaluated data libraries are in agreement with our new data to within the experimental uncertainties.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗