Search NASA⌕ Search

SEARCH · Search NASA

Results for “applied computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Evaluation of solution procedures for material and/or geometrically nonlinear structural analysis by the direct stiffness method.

This paper presents an assessment of the solution procedures available for the analysis of inelastic and/or large deflection structural behavior. A literature survey is given which summarized the contribution of other researchers in the analysis of structural problems exhibiting material nonlinearities and combined geometric-material nonlinearities. Attention is focused at evaluating the available computation and solution techniques. Each of the solution techniques is developed from a common equation of equilibrium in terms of pseudo forces. The solution procedures are applied to circular plates and shells of revolution in an attempt to compare and evaluate each with respect to computational accuracy, economy, and efficiency. Based on the numerical studies, observations and comments are made with regard to the accuracy and economy of each solution technique.

Stricklin, J. A.↗

The determination of equivalent bearing loading for the BSMT that simulate SSME high pressure oxidizer turbopump conditions using the SHABERTH/SINDA computer programs

The MSFC bearing seal material tester (BSMT) can be used to evaluate the SSME high pressure oxygen turbopump (HPOTP) bearing performance. The four HPOTP bearings have both an imposed radial and axial load. These radial and axial loads are caused by the HPOTP's shaft, main impeller, preburner impeller, turbine and by the LOX coolant flow through the bearings, respectively. These loads coupled with bearing geometry and operating speed can define bearing contact angle, contact Hertz stress, and heat generation rates. The BSMT has the capability of operating at HPOTP shaft speeds, provide proper coolant flowrates but can only apply an axial load. Due to the inability to operate the bearings in the BSMT with an applied radial load, it is important to develop an equivalency between the applied axial loads and the actual HPOTP loadings. A shaft-bearing-thermal computer code (SHABERTH/SINDA) is used to simulate the BSMT bearing-shaft geometry and thermal-fluid operating conditions.

Mcdonald, Gary H.↗

Numerical Predictions of Mode Reflections in an Open Circular Duct: Comparison with Theory

The NASA Broadband Aeroacoustic Stator Simulation code was used to compute the acoustic field for higher-order modes in a circular duct geometry. To test the accuracy of the results computed by the code, the duct was terminated by an open end with an infinite flange or no flange. Both open end conditions have a theoretical solution that was used to compare with the computed results. Excellent comparison for reflection matrix values was achieved after suitable refinement of the grid at the open end. The study also revealed issues with the level of the mode amplitude introduced into the acoustic held from the source boundary and the amount of reflection that occurred at the source boundary when a general nonreflecting boundary condition was applied.

Duct Modes↗

Improved technique for digital simulation of bending and slosh phenomena

Mathematical model representation of bending and slosh phenomena in the Saturn vehicle results in linear second order differential equations. Improved technique was developed to provide a real-time digital solution of the equations. The technique may also be applied to nonreal time digital simultations, resulting in savings of digital computer time.

Stauffer, N. E.↗

Structural-Thermal-Optical Program (STOP)

A structural thermal optical computer program is developed which uses a finite element approach and applies the Ritz method for solving heat transfer problems. Temperatures are represented at the vertices of each element and the displacements which yield deformations at any point of the heated surface are interpolated through grid points.

Lee, H. P.↗

User document for computer programs for ring-stiffened shells of revolution

A user manual and related program documentation is presented for six compatible computer programs for structural analysis of axisymmetric shell structures. The programs apply to a common structural model but analyze different modes of structural response. In particular, they are: (1) Linear static response under asymmetric loads; (2) Buckling of linear states under asymmetric loads; (3) Nonlinear static response under axisymmetric loads; (4) Buckling nonlinear states under axisymmetric (5) Imperfection sensitivity of buckling modes under axisymmetric loads; and (6) Vibrations about nonlinear states under axisymmetric loads. These programs treat branched shells of revolution with an arbitrary arrangement of a large number of open branches but with at most one closed branch.

Cohen, G. A.↗

Power spectral density estimation by spline smoothing in the frequency domain

An approach, based on a global averaging procedure, is presented for estimating the power spectrum of a second order stationary zero-mean ergodic stochastic process from a finite length record. This estimate is derived by smoothing, with a cubic smoothing spline, the naive estimate of the spectrum obtained by applying FFT techniques to the raw data. By means of digital computer simulated results, a comparison is made between the features of the present approach and those of more classical techniques of spectral estimation.

Defigueiredo, R. J. P.↗

Analysis of swimming motions.

This paper presents an analysis of swimming motion with specific attention given to the flutter kick, the breast-stroke kick, and the breast stroke. The analysis is completely theoretical. It employs a mathematical model of the human body consisting of frustrums of elliptical cones. Dynamical equations are written for this model including both viscous and inertia forces. These equations are then applied with approximated swimming strokes and solved numerically using a digital computer. The procedure is to specify the input of the swimming motion. The computer solution then provides the output displacement, velocity, and rotation or body roll of the swimmer.

Gallenstein, J.↗

The anatomy of floating shock fitting

The floating shock fitting technique is examined. Second-order difference formulas are developed for the computation of discontinuities. A procedure is developed to compute mesh points that are crossed by discontinuities. The technique is applied to the calculation of internal two-dimensional flows with arbitrary number of shock waves and contact surfaces. A new procedure, based on the coalescence of characteristics, is developed to detect the formation of shock waves. Results are presented to validate and demonstrate the versatility of the technique.

Salas, M. D.↗

Total reduction of distorted echelle spectrograms - An automatic procedure

A total reduction procedure, notable for its use of a computer-controlled microdensitometer for semi-automatically tracing curved spectra, is applied to distorted high-dispersion echelle spectra recorded by an image tube. Microdensitometer specifications are presented and the FORTRAN, TRACEN and SPOTS programs are outlined. The intensity spectrum of the photographic or electrographic plate is plotted on a graphic display. The time requirements are discussed in detail.

Peterson, R. C.↗

Investigations with satellite data temperature retrievals

A method is presented for using satellite measurements to interpolate vertical temperature soundings between radiosonde stations. The method finds a set of coefficients, which when multiplied by corresponding measured radiance quantities, yield zero temperature error at a radiosonde station. This derived set of coefficients is then applied to satellite radiance measurements at places between radiosonde stations. The computations show, for example, that the average absolute error in the layer 1000-800 mbs is only 0.3K when the corresponding 'minimum-information' method error was 2.9K. The method may be most applicable to measurements from geostationary satellites, but should also be applicable to measurements from polar orbiting satellites under certain conditions.

Fritz, S.↗

A three-dimensional, time-dependent model of Mobile Bay

A three-dimensional, time-variant mathematical model for momentum and mass transport in estuaries was developed and its solution implemented on a digital computer. The mathematical model is based on state and conservation equations applied to turbulent flow of a two-component, incompressible fluid having a free surface. Thus, bouyancy effects caused by density differences between the fresh and salt water, inertia from thare river and tidal currents, and differences in hydrostatic head are taken into account. The conservation equations, which are partial differential equations, are solved numerically by an explicit, one-step finite difference scheme and the solutions displayed numerically and graphically. To test the validity of the model, a specific estuary for which scaled model and experimental field data are available, Mobile Bay, was simulated. Comparisons of velocity, salinity and water level data show that the model is valid and a viable means of simulating the hydrodynamics and mass transport in non-idealized estuaries.

Pitts, F. H.↗

Development and application of operational techniques for the inventory and monitoring of resources and uses for the Texas coastal zone

The author has identified the following significant results. Four LANDSAT scenes were analyzed for the Harbor Island area test sites to produce land cover and land use maps using both image interpretation and computer-assisted techniques. When evaluated against aerial photography, the mean accuracy for three scenes was 84% for the image interpretation product and 62% for the computer-assisted classification maps. Analysis of the fourth scene was not completed using the image interpretation technique, because of poor quality, false color composite, but was available from the computer technique. Preliminary results indicate that these LANDSAT products can be applied to a variety of planning and management activities in the Texas coastal zone.

Harwood, P.↗

The micrometeoroid complex and evolution of the lunar regolith

Monte Carlo-based computer calculations, as well as analytical approaches utilizing probabilistic arguments, were applied to gain insight into the principal regolith impact processes and their resulting kinetics. Craters 10 to 1500 m in diameter are largely responsible for the overall growth of the regolith. As a consequence the regolith has to be envisioned as a complex sequence of discrete ejecta blankets. Such blankets constitute first-order discontinuities in the evolving debris layer. The micrometeoroid complex then operates intensely on these fresh ejecta blankets and accomplishes only in an uppermost layer of approximately 1-mm thickness. The absolute flux of micrometeoroids based on lunar rock analyses averaged over the past few 10 to the 6th power years is approximately an order of magnitude lower than presentday satellite fluxes; however, there is indication that the flux increased in the past 10 to the 4th power years to become compatible with the satellite data. Furthermore, there is detailed evidence that the micrometeoroid complex existed throughout geologic time.

Horz, F.↗

System and method for tracking a signal source

A system for tracking moving signal sources is disclosed which is particularly adaptable for use in tracking stage performers. A miniature transmitter is attached to the person or object to be tracked and emits a detectable signal of a predetermined frequency. A plurality of detectors positioned in a preset pattern sense the signal and supply output information to a phase detector which applies signals representing the angular orientation of the transmitter to a computer. The computer provides command signals to a servo network which drives a device such as a motor driven mirror reflecting the beam of a spotlight, to track the moving transmitter.

Mogavero, L. N.↗

Cooling rates for lunar samples determined with a diffusion model for phosphide exsolution

A numerical model for diffusion-controlled phase growth has been applied to the exsolution of phosphide lamellae in lunar metal grains. Computer simulations reproduce observed composition profiles, and reveal the influence of cooling rate on dimensional and compositional parameters of phosphide and metal. At lower cooling rates, phosphide lamellae are larger and the concentration of P in the metal host close to the interface is lower. Cooling rates inferred for Apollo 16 samples, based on compositions and dimensions of the phosphide-metal grains, are mostly in the range 1-100 C/day. These rates correspond to burial depths of 5-0.5 m for melt rocks and 3-0.3 m for breccias. This is in good agreement with thicknesses of lunar cooling units determined by other techniques.

Hewins, R. H.↗

Filtering technique based on high-frequency plant modeling for high-gain control

This invention was an improvement in aircraft control systems that utilized feedback motion sensors to generate a signal to control the aircraft. The improvement consisted essentially of a complementary filter comprising a simplified model of the aircraft, a high pass filter, a low pass filter and a summing amplifier. The control signal was applied to the simplified model of the aircraft which attempted to compute the vehicle response to the signal. This computed response was then fed into the high pass filter to eliminate long term errors in the calculated response, with the result that a good estimate of the high frequency content of the aircraft motion was obtained. In order to obtain a good estimate of the low frequency content of the motion, a rate gyro signal was fed through the low pass filter that eliminates all of the offending noise.

Niessen, F. R.↗

An image-data-compression algorithm

Cluster Compression Algorithm (CCA) preprocesses Landsat image data immediately following satellite data sensor (receiver). Data are reduced by extracting pertinent image features and compressing this result into concise format for transmission to ground station. This results in narrower transmission bandwidth, increased data-communication efficiency, and reduced computer time in reconstructing and analyzing image. Similar technique could be applied to other types of recorded data to cut costs of transmitting, storing, distributing, and interpreting complex information.

Hilbert, E. E.↗