Search NASA⌕ Search

SEARCH · Search NASA

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Strength and rupture geometry of un-irradiated C26M FeCrAl under LOCA burst testing conditions

Ferritic iron-chromium-aluminum (FeCrAl) alloys are an accident tolerant fuel candidate to replace the incumbent Zr-based claddings. Nuclear grade FeCrAl alloys are marked by superior high temperature mechanical behavior and exceptional steam oxidation resistance, both of which increase safety margins during accident scenarios. In the present study, the loss of coolant accident (LOCA) burst behaviors of three un-irradiated commercially fabricated cladding materials in a simulated LOCA environment were compared: (1) T35Y2, a 1 st generation nuclear grade FeCrAl, (2) C26M, a 2 nd generation nuclear grade FeCrAl, and (3) Zircaloy-2. Both FeCrAl alloys showed improved mechanical strength and steam oxidation resistance compared to Zircaloy-2. C26M claddings burst at significantly higher temperatures for all tested engineering hoop stresses, had limited ballooning, and demonstrated preferential fuel retention behavior in terms of burst opening area and length. High temperature tensile data for C26M is also presented. For both un-irradiated FeCrAl alloys, it was found that a distinct “threshold” burst stress signified the transition between small and large openings. Finally, higher threshold hoop stresses were associated with higher uniaxial strength for the FeCrAl alloys, indicating that tensile data, rather than creep data, could be useful for predicting rupture size and assessing fuel dispersal concerns.

36 MATERIALS SCIENCE↗

Investigation of δ zirconium hydride morphology in a single crystal using quantitative phase field simulations supported by experiments

In light water nuclear reactors, waterside corrosion of the cladding material leads to the production of hydrogen, a fraction of which is picked up by the zirconium cladding and precipitates into brittle hydride particles. These nanoscale hydride particles aggregate into mesoscale hydride clusters. The principal stacking direction of the nanoscale hydrides precipitated in the cladding tube changes from circumferential in the absence of applied stress to radial under circumferential applied stress. A quantitative phase field model has been developed to predict the hydride morphology observed experimentally and identify the mechanisms responsible for nanoscale hydride stacking. The model focuses on nanoscale hydride precipitation in a single zirconium grain with a detailed description of the anisotropic elastic contribution. The model predictions concerning the shape, orientation, and stacking behavior of nanoscale hydride are analyzed and compared with experimental observations. The model accurately accounts for the experimentally observed elongated nanoscale hydride shape and the stacking of hydrides along the basal plane of the hexagonal zirconium matrix. When investigating the role of applied stress in hydride morphology, the model challenges some of the mechanisms previously proposed to explain hydride reorientation. Finally, although hydride reorientation has been hypothesized to be caused by a change in nanoscale hydride shape, the current study shows that these mechanisms are unlikely to occur.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Micro-tensile testing of the bond line in hot isostatic pressed aluminum

Considerable effort is being devoted to development and regulatory qualification of low enriched fuels for research and test reactors by many agencies worldwide. One promising fuel configuration being examined for United States higher power research and test reactors (USHPRRs) are plate-type fuels composed of a metallic uranium-molybdenum foil clad in an aluminum alloy. The two pieces of aluminum alloy cladding are bonded using a hot isostatic pressing method. The mechanical properties of the resulting bond line in the aluminum alloy cladding will vary by the HIP'ing parameters, requiring a need to characterize the bond line. Small scale mechanical testing can provide a path for evaluating the mechanical properties and deformation behavior of the bond line both prior to and following irradiation. Here, in this research, room temperature micro-tensile specimens of non-irradiated and irradiated samples containing an Al alloy (AA 6061) bond line were tested to evaluate its strength and deformation behavior. Observations indicated that the strain rate did not affect the deformation behavior or strength and most of the micro-tensile specimens failed in a ductile mode in grains around the bond line. There was no indication that the microstructural features from the bond line affected the mechanical properties of the micro-tensile specimens. An initial examination was performed on irradiated material but further systematic studies of the effects of irradiation can be performed in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Burst and oxidation behavior of Cr-coated Zirlo during simulated LOCA testing

We report Cr-coated Zr-alloys are a near-term cladding concept to improve reactor safety during accident scenarios. Burst and steam oxidation behavior of bare and Cr-coated Zirlo claddings were examined under simulated loss-of-coolant accident conditions. The 4.4 µm coating had no substantial effect on ballooning or opening geometry but did increase burst temperatures at higher pressures. The coating reduced steam oxidation of the cladding compared to bare specimens, but in regions of high strain, the coating developed through-cracks allowing rapid underlying zirconia formation.

36 MATERIALS SCIENCE↗

Development and formulation of physics based metallic fuel models and comparison to integral irradiation data

Metallic fuel has an important historical significance in the development of nuclear reactors and continues to be relevant to the progression of advanced test and power reactors. A number of models, ranging from empirical to mechanistic, have been developed and implemented in various fuel performance codes to describe U-Zr and U-Pu-Zr fuel and typical fast reactor cladding materials. One challenge of using these models to simulate fuel performance is the inevitable tangling of coupled phenomena that can cloud proper implementation, calibration, and eventual utilization of new models. Here in an effort to provide a baseline capability that will facilitate the use of advanced models, new capabilities have been implemented into the fuel performance code BISON specific to metallic fuel simulations, ranging from materials properties, fission gas release and swelling calculations, coolant channel models, and cladding correlations. These models have been applied to the X441/X441A EBR-II experimental assembly data, a set of irradiated metallic UPuZr fuel rods of varying pin designs. The models implemented in BISON are able to capture the general trend of the expected response of the fuel and cladding to irradiation in EBR-II, especially when considering the spread in experimental measurements and the uncertainties inherited from the historical material models. Ultimately, the models outlined here provide the baseline capabilities on which new models can build upon in order to improve the prediction of metallic fuel performance simulations in off-normal designs or operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Through-thickness recrystallization characteristics of a laminated AA3xxx–AA6xxx aluminum alloy system

The through-thickness annealing behavior of a laminated AA3xxx–AA6xxx alloy system at 300 °C has been studied by scanning electron microscopy, electron backscatter diffraction analysis, electron probe micro-analysis, differential scanning calorimetry, and hardness measurement. Results show that the recrystallization process starts at the interface region between the AA3xxx (clad) and AA6xxx (core) layers. Subsequently, the recrystallization process front progresses into the core layer, while the clad layer is the last region to recrystallize. It is also found that precipitation precedes recrystallization in the entire laminate at the investigated temperature. The preferential onset of recrystallization at the interface region is attributed to the net driving pressure being the highest in this region. The factors that lead to such enhanced net driving pressure are (a) deformation incompatibility between the two alloy layers, (b) lower solute content of the interface, which also leads to lower volume fraction of precipitates, and (c) an accelerated rate of precipitate coarsening due to the presence of a higher density of dislocations. The gradual progress of recrystallization from the interface towards the core layer is dictated by precipitate coarsening and the dependence of its rate on the density of deformation-induced dislocations. The lower driving pressure due to lower work hardening capacity, high solute drag pressure due to Mn, and additional Zener drag from precipitates that form due to solute redistribution during annealing explain the late initiation of recrystallization in the clad layer. - Highlights: • The through-thickness recrystallization of a laminated system is investigated. • The early onset of recrystallization at the interface is discussed. • The effects of precipitation and coarsening on recrystallization are analyzed.

36 MATERIALS SCIENCE↗

Advanced 3D characterisation of iodine induced stress corrosion cracks in zirconium alloys

Highlights: • Macroscopic crack direction is affected by metallurgical state. • High resolution XCT reveals complex crack morphology. • 3D-EBSD used to fully characterise attacked grain boundaries. • Evidence of iodine segregation ahead of a crack tip. - Abstract: In this study, a range of advanced techniques have been used to characterise iodine-induced stress corrosion cracks, and investigate their interaction with microstructure in zirconium alloys used as cladding material in nuclear power reactors. C-ring samples, machined from cladding tubes in a recrystallised and cold worked condition, were subjected to compressive stress while submerged in an iodine-ethanol solution to simulate stress corrosion cracks arising from pellet cladding interaction. The complex morphology of these stress corrosion cracks was imaged in 3D using X-ray computed tomography (XCT), and subsequent analysis using both 2D and 3D electron backscatter diffraction (EBSD) allowed for the interaction of these cracks with microstructure to be investigated. Intergranular cracking modes were observed to dominate in the recrystallised microstructure, resulting in cracking in the radial direction with variations on the order of the grain size. Crack propagation in the cold worked microstructure was observed to be correlated with the direction of the elongated grains, resulting in a more tangential crack path with less local variation and a microstructure potentially more susceptible to iodine-induced stress corrosion cracking. 3D-EBSD using serial sectioning allows for the determination of the full five-parameter grain boundary description, and opens up the possibility of a statistical analysis of susceptible boundaries to SCC. Nanoscale secondary ion mass spectrometry (NanoSIMS) was also used to map the chemical distribution in the crack tip region and provides possible evidence of iodine segregation ahead of the crack tip. The results provide new insight into crack propagation mechanisms in recrystallised and cold worked microstructures, and pave the way for a more mechanistic understanding of crack propagation through advanced characterisation of iodine-induced stress corrosion cracks in zirconium alloys.

36 MATERIALS SCIENCE↗

Diffusion behavior of lanthanide-additive compounds (Ce 4 Sb 3 , Ce 2 Sb, and CeTe) against HT9 and Fe

Antimony and tellurium have been identified as promising additives in metallic fuel, which can immobilize free-lanthanide fission products into stable intermetallic compounds in order to mitigate the fuel-cladding chemical interaction. Ce 4 Sb 3 , Ce 2 Sb, and CeTe are the primary compounds formed by Sb or Te with the lanthanide Ce present in the fuel. If these compounds are present at the outer periphery of the fuel, they will come in contact with and react with the cladding after the fuel swells. The present study investigates the reactivity of these compounds with two cladding materials, HT9 and Fe. The diffusion couple tests between these compounds and HT9 or Fe were conducted at 853 K. Scanning electron microscopy and transmission electron microscopy were used to analyze the morphology, microstructure, and phase distribution of the diffusion region. It was observed that the diffusion region thickness formed by the three compounds was significantly reduced compared to free Ce. Moreover, there was no observed diffusion or reaction between Ce 4 Sb 3 or Ce 2 Sb with either HT9 or Fe. CeTe was found to diffuse and react with HT9, forming Cr 3 Te 4 and TeFe at the diffusion region, as well as to penetrate into Fe, mainly by intergranular diffusion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High burn-up spent nuclear fuel transport reliability investigation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During road or rail transportation, SNF will experience unique conditions that could affect the structural integrity of the cladding due to vibrational and impact loading. Lack of SNF inertia-induced dynamic fatigue data, especially for the high burn-up (HBU) SNF systems, has brought significant challenges to quantify the reliability of SNF during transportation with a high degree of confidence. To address this shortcoming, Oak Ridge National Laboratory (ORNL) developed a SNF vibration testing protocol without fuel pellets removal, which has provided significant insight regarding the dynamics of mechanical interactions between pellet and cladding. This research has provided a detailed understanding about the effect of loading rate and loading mode on the fatigue damage evolution of HBU SNF under normal conditions of transport (NCT). Static and dynamic loading experimental data were generated for SNF under simulated transportation environments using a cyclic integrated reversible-bending fatigue tester (CIRFT), an enabling hot-cell testing technology developed at ORNL. SNF flexural tensile strength and fatigue S-N data from pressurized water reactors (PWRs) and boiling water reactor (BWR) HBU SNF are presented in this paper, including the potential effects of pellet-cladding interface bonding, hydride reorientation, and thermal annealing to SNF vibration reliability. The data presented here can be used to meet the nuclear industry and U.S. Nuclear Regulatory Commission needs in safety of SNF transportation operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗

Integral LOCA fragmentation test on high-burnup fuel

Increasing the fuel burnup limit in light water reactors is sought to enhance fuel cycle economics and requires establishing a technical basis. Experimental observations of severe fuel fragmentation under loss-of-coolant-accident conditions at Halden and Studsvik had raised the need for additional considerations during the development of this technical basis. These test data suggested that the burnup threshold for high burnup fuel fragmentation may be influenced by pre-transient power. Additional loss-of-coolant-accident test data is therefore valuable to complement these tests and enhance the current state of understating. Oak Ridge National Lab has developed the Severe Accident Test Station capable of examining the oxidation kinetics and accident response of irradiated fuel and cladding materials for design basis accident and beyond design basis accident scenarios. Severe Accident Test Station provides various temperature profiles, steam, and the thermal shock conditions necessary for integral loss of coolant accident testing, defueled oxidation quench testing, and high-temperature beyond design basis accident testing. Severe Accident Test Station has been successfully installed and demonstrated in the Irradiated Fuels Examination Laboratory at Oak Ridge National Lab. Furthermore, descriptions of the in-cell re-fabrication capabilities and assembly of the loss-of-coolant-accident test train are provided. Installation of the Severe Accident Test Station system and in-cell re-fabrication restores United States capability to examine postulated and extended loss-of-coolant-accident conditions on spent fuel and cladding and provides a platform for evaluating advanced fuel and accident-tolerant fuel cladding concepts. Lastly, three in-cell integral loss-of-coolant-accident test were performed in the Severe Accident Test Station and compared to the Nuclear Regulatory Commission sponsored loss-of-coolant-accident test as well as the original loss-of-coolant-accident test performed at Argonne National Lab. Finally, the results of these tests as well as all publicly available integral loss-of-coolant-accident test were used to validate a threshold for high burnup fuel fragmentation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A mortar thermomechanical contact computational framework for nuclear fuel performance simulation

Nuclear fuel performance simulations involve the modeling of complex physical phenomena, ranging from fission gas release to fuel swelling and other temperature-induced effects. For light-water reactors (LWRs), swelling of the fuel and the pressure it imposes on the clad when they come into contact causes permanent clad deformation. Accurately characterizing the fuel-cladding interaction, which involves multiple physics, is essential to accurately simulate the fuel/cladding system. Thermomechanical modeling of this problem using a variationally consistent enforcement (e.g., a mortar approach) has been shown to improve the quality of results and facilitate convergence. Here, we present a general multiphysics computational framework for solving nuclear fuel problems using a mortar approach in BISON, a nuclear fuel performance code. In this study analyses show that using the mortar approach, which enables variationally consistent constraint enforcement, improves the quality of results as compared to the more commonly used node-on-face enforcement for representative LWR nuclear fuel simulations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Reactivity-initiated accidents in two pressurized water reactor high burnup core designs

Here, this paper presents a safety analysis of two proposed core loadings for 24-month Pressurized Water Reactor (PWR) fuel cycles. This analysis focuses on reactivity-initiated accidents (RIAs) and evaluates core safety performance impacts of rod-averaged burnup limits up to 75 GWD/MTU and less than 7 % enriched UO 2 . The capabilities of Polaris, PARCS, and RELAP5-3D are leveraged to evaluate the core neutronic and thermal–hydraulic behavior for normal-operation, uncontrolled control rod withdrawal (CRW) transients, and control rod ejection (CRE) accidents. The two core designs are compared to identify features of realistic high burnup/extended enrichment core design approaches which have significant safety impact, identify experimental data needs for high-fidelity predictive modeling, and provide recommendations for future high burnup core designs. The first core design evaluated in this study was developed by Southern Nuclear Company and used an ZrB 2 Integral Fuel Burnable Absorber (IFBA) and B 4 C Wet-Annular Burnable Absorber (WABA)-based burnable poison strategy. The second core design assessed in this work used a Gd 2 O 3 -doped UO 2 burnable poison, similar to that used in boiling water reactors or French PWRs. Results indicate that fuel thermal limits are maintained for limiting CRW and hot full power (HFP) CRE transients. Cladding failure is predicted for the highest energy deposition rods in each core during limiting hot zero power (HZP) CRE accidents (where maximum radially averaged enthalpy exceeds 120 cal/g), though licensing may be permissible with a limited number of failed rods. While concerns exist regarding high critical boron concentration during steady state for the IFBA core and large plenum pressures for the gadolinia core design, the analysis demonstrates adequate safety performance during limiting RIA accident scenarios for two representative high burnup core designs. Design changes limiting plenum pressures and implementation of accident tolerant fuel (ATF) cladding features which minimize hydriding and susceptibility to pellet-cladding mechanical interaction (PCMI) are recommended for future high burnup fuel concepts. To support the technical basis for burnup limit increases, high-fidelity fuel performance models are needed to address physical effects not considered in this analysis, and high burnup irradiated fuel tests are required to extend applicability of the fuel failure limits and validate existing and future models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Transient fuel performance analysis for the preliminary fuel concept of general atomics fast modular reactor

This study investigates the transient fuel performance of General Atomics Fast Modular Reactor (GA-FMR) during accident scenarios, focusing on the behavior of its innovative fuel system that combines high-assay low enriched uranium dioxide (HALEUO2) fuel with SiGA® ceramic matrix composite silicon carbide cladding. The preliminary fuel design’s response was analyzed during reactivity-initiated accidents (RIA) and loss of coolant accidents (LOCA) using BISON fuel performance analysis code, which included both the diffusion enhanced and BISON-FASTGRASS coupled UO 2 models. The RIA analysis demonstrated that effective reactivity control reduced fuel temperature, though with transient fission gas release resulting in additional tensile stress state on the cladding. LOCA simulations revealed differing predictions between the two models: the BISON UO 2 model showed more transient fission gas release but minimal pellet expansion, while the BISON-FASTGRASS UO 2 model predicted less pronounced fission gas release but more fuel swelling and thermal expansion, potentially leading to pellet-cladding mechanical interaction. Here, these findings highlight critical areas for fuel design optimization and identify knowledge gaps requiring further experimental and computational investigation to advance GA-FMR fuel development.

Lee, Soon K. [Argonne National Laboratory (ANL), A↗

Applying U.S. metal fuel experience to new fuel designs for fast reactors

With the increasing interest in small modular reactors or microreactors, developers are working to design and submit licensing approval requests of U–10Zr-fueled fast reactors. The developers and their proponents cite prior metal fuel experience (worldwide, but U.S. experience in particular for many developers) as the motivation and justification for their reactor concepts. The experience with metal fuel deployment in sodium-cooled fast reactors as well as the underlying irradiation testing database, provide a suitable basis for analytically justifying the use of metal fuel in new reactors. The evolution of metal fuel design and capability illustrates the importance of key fuel design parameters to consider in new applications of the prior experience: fuel smeared density, plenum-to-fuel volume ratio, the ratio of cladding radius to thickness, fuel composition, and cladding and duct materials. In-service operating and deployment conditions to be considered include fuel linear heat generation rate, fuel temperature, cladding temperature, peak burnup and peak fast fluence. Fuel designs and in-service conditions that are bounded by the database and experience are most easily addressed, but deviations from those previous parameters and conditions can be addressed by considering impacts on previously established behavior and applying other mitigating conservatisms, as appropriate. Here, the authors recommend any new deployment proceed with fuel surveillance and monitoring to mitigate risk, application of conservative measures to address uncertainties, and a fuel qualification program that addresses a range of in-service operating conditions with production fuel. The work reported should be of interest to students and regulators unfamiliar with metal fuel in fast reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Laser-based characterization of nuclear fuel plates

Ensuring the integrity of fuel-clad and clad-clad bonding in nuclear fuels is important for safe reactor operation and assessment of fuel performance, yet the measurement of bond strengths in actual fuels has proved challenging. The laser shockwave technique (LST) originally developed to characterize structural adhesion in composites is being employed to characterize interface strength in a new type of plate fuel being developed at Idaho National Laboratory (INL). LST is a non-contact method that uses lasers for the generation and detection of large-amplitude acoustic waves and is well suited for application to both fresh and irradiated nuclear-fuel plates. This paper will report on initial characterization results obtained from fresh fuel plates manufactured by different processes, including hot isostatic pressing, friction stir welding, and hot rolling.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The effect of Ta interface on the crystallization of amorphous phase change material thin films

The crystallization of amorphous GeTe and Ge{sub 2}Sb{sub 2}Te{sub 5} phase change material films, with thickness between 10 and 100 nm, sandwiched between either Ta or SiO{sub 2} layers, was investigated by optical reflectivity. Ta cladding layers were found to increase the crystallization temperature, even for films as thick as 100 nm. X-Ray diffraction investigations of crystallized GeTe films showed a very weak texture in Ta cladded films, in contrast with the strong texture observed for SiO{sub 2} cladding layers. This study shows that crystallization mechanism of phase change materials can be highly impacted by interface effects, even for relatively thick films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Guiding light via slippery liquid-infused porous surfaces

Slippery liquid-infused porous surfaces (SLIPSs) have been explored for many applications, taking advantage of their highly non-wetting property. In this work, we explore the SLIPS as a cladding material for waveguiding. SLIPSs are prepared by infusing perfluoropolyether oil to hydrophobized nanoporous surfaces of silicon. Power loss and transmission efficiency of an HeNe laser (1.82 mW and 632.8 nm) with varying incident angles were measured through microchannels consisting of the SLIPSs as cladding layers (noil = 1.30) and water (nwater = 1.33) as a core, compared to other cladding types including a planar silicon surface and the nanoporous surfaces in hydrophilic (Wenzel state) and hydrophobic (Cassie–Baxter state) conditions with no oil infused. Agreeing with Snell's law, a total internal reflection occurs at the incident angle as high as 14° for the SLIPSs. The waveguide loss at 14° is only 1.8 dB/cm for the SLIPSs, while those for planar silicon, hydrophilic nanoporous, and hydrophobic nanoporous surfaces are 5.9, 7.4, and 4.9 dB/cm, respectively. The power transmission efficiency of the SLIPSs is independent of the porosity because the surfaces are fully covered with the oil layer, whereas those of hydrophilic and hydrophobic nanoporous surfaces, whose pores are filled with water and air, respectively, depend on the porosity. The significantly lower power loss and the insensitivity to the surface porosity are advantages of the SLIPSs over the other surfaces and can benefit in waveguiding applications such as optofluidics.

Asawa, Kaustubh (ORCID:0000000197142555)↗