Search NASA⌕ Search

SEARCH · Search NASA

Results for “code validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Validation Gap Assessment of a TN B1 Package Containing Fresh, Metallic Sodium-Cooled Fuel

This report describes an assessment of sodium fast reactor assemblies loaded inside a Transnuclear B1 package. The assessment was performed to determine the state of the validation basis for sodium fast reactor fuel within a transportation package originally intended for fresh, light-water reactor fuel assemblies. The study employed the TSUNAMI-3D and TSUNAMI-IP sequences from the SCALE code system to determine correlation coefficients between various configurations and databases of validation assessments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Resolving broadening of ECRH deposition due to edge turbulence in DIII-D by heat deposition measurement

Interaction between microwave power, used for local heating and mode control, and density fluctuations can produce a broadening of the injected beam, as confirmed in experiment and simulation. Increased power deposition width could impact suppression of tearing mode structures on ITER[1]. This work discusses the experimental portion of an effort to understand scattering of injected microwaves by turbulence on the DIII-D tokamak. The corresponding theoretical modeling work can be found in M.B. Thomas et. al.: Submitted to Nuclear Fusion (2017)[Author Note - this paper to be published in same journal]. In a set of perturbative heat transport experiments, tokamak edge millimeter-scale fluctuation levels and microwave heat deposition are measured simultaneously. Beam broadening is separated from heat transport through fitting of modulated fluxes[2]. Electron temperature measurements from a 500 kHz, 48-channel ECE radiometer are Fourier analyzed and used to calculate a deposition-dependent flux[3]. Consistency of this flux with a transport model is evaluated. A diffusive(∝ ∇˜ T e ) and convective(∝ ˜ T e ) transport solution is linearized and compared with energy conservation-derived fluxes. Comparison between these two forms of heat flux is used to evaluate the quality of ECRF deposition profiles, and a Χ 2 minimization finds a significant broadening of 1D equilibrium ray tracing calculations from the benchmarked TORAY-GA ray tracing code[4] is needed. The physical basis, cross-validation, and application of the heat flux method is presented. The method is applied to a range of DIII-D discharges and finds a broadening factor of the deposition profile width which scales linearly with edge density fluctuation level. Furthermore, these experimental results are found to be consistent with the full-wave beam broadening measured by the 3D full wave simulations in the same discharges[5].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DEVELOPMENT OF A NONLINEAR TIME DOMAIN METHODOLOGY, RESULTS (PART II)

A complementary paper, “Development of a Nonlinear Time Domain Methodology (Part I),” lays out a methodology to follow when performing nonlinear soil-structure interaction (NLSSI) analysis. This paper presents results from numerical analyses that compare a recently verified and validated version of SASSI with those from a NLSSI code using increasing levels of earthquake ground motion. Comparisons will be presented at multiple locations inside a generic nuclear power plant structure. The generic NPP is placed on a well-studied soil site. NLSSI results are verified by comparing the recently V&V version of SASSI with NLSSI. At low levels of ground motion the linear analysis and NLSSI produce similar results with results diverging for higher levels of ground motion. Results show that differences in the spectral accelerations calculated using the equivalent linear and nonlinear methods are observed at significant levels of ground motion shaking. For the NPP analyse, the differences are associated with gapping and sliding, which cannot be captured explicitly with equivalent linear analysis.

42 ENGINEERING↗

Effective Lanthanide Diffusivity through U-Zr Metallic Fuel

Fuel-cladding chemical interaction (FCCI) is one of the main concerns for the performance of U-Zr metallic fuels. Although FCCI results in complex phase transformations and morphological changes in both the fuel and cladding sides of the interface, the formation of a brittle layer in the cladding side of the interface (sometimes referred to as wastage) has one of the most significant impacts on the cladding mechanical integrity. This brittle layer is associated with the formation of intermetallic compounds between the cladding constituents Fe, Cr and the lanthanide fission product species. The formation of this cladding wastage layer has been the focus of recent efforts to develop a mechanistic modeling framework, including production of lanthanides in the fuel, transport through the fuel to the fuel-cladding interface, and phase transformation to form intermetallic phases. To calculate the rate of transport of lanthanides through the fuel, a multi-scale computational approach has been used. Atomistic calculations have been performed to determine the diffusivities of Nd, the most prevalent lanthanide species, through the solid fuel matrix and along pore surfaces. These diffusivities have been used as input parameters for a mesoscale model to determine an effective diffusion coefficient that accounts for the formation of porosity, its interconnection, and infiltration with bond sodium from the fuel-cladding gap. The effective diffusivity has been used in engineering-scale simulations using the BISON fuel performance code, and BISON simulations have been compared to representative validation cases from the EBR-II reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of integrated core disruptive accident analysis code for FBR - ASTERIA-FBR

The evaluation of consequence at the severe accident is the most important as a safety licensing issue for the reactor core of liquid metal cooled fast breeder reactor (LMFBR), since the LMFBR core is not in an optimum condition from the viewpoint of reactivity. This characteristics might induce a super-prompt criticality due to the core geometry change during the core disruptive accident (CDA). The previous CDA analysis codes have been modeled in plural phases dependent on the mechanism driving a super-prompt criticality. Then, the following event is calculated by connecting different codes. This scheme, however, should introduce uncertainty and/or arbitrary to calculation results. To resolve the issues and obtain the consistent calculation results without arbitrary, JNES is developing the ASTERIA-FBR code for the purpose of providing the cross-check analysis code, which is another required scheme to confirm the validity of the evaluation results prepared by applicants, in the safety licensing procedure of the planned high performance core of Monju. ASTERIA-FBR consists of the three major calculation modules, CONCORD, dynamic-GMVP, and FEMAXI-FBR. CONCORD is a three-dimensional thermal-hydraulics calculation module with multi-phase, multi-component, and multi-velocity field model. Dynamic-GMVP is a space-time neutronics calculation module. FEMAXI-FBR calculates the fuel pellet deformation behavior and fuel pin failure behavior. This paper describes the needs of ASTERIA-FBR development, major module outlines, and the model validation status. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Experimental Data and Analysis for a New Irradiation Facility

A new experimental facility is being developed for materials irradiation and testing at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR). Details of this facility have been presented before. A prototype of this facility, the Thermosyphon Test Loop (TSTL), has been built, and experimental data have been obtained and analyzed. The purpose of the tests was to establish a safe operating envelope for actual fueled experiments in a HFIR experimental facility. Both steady-state and transient experiments were conducted. The data will also be used to validate computer simulations of the thermosyphon so that those codes can be used for future safety-basis calculations. This paper presents a summary of the TSTL experimental data and analysis. A report with all the data and analyses will be published in the near future. Experimental data from 51 tests in the TSTL have been obtained. This extensive set of high quality data can be used to benchmark codes with boiling and condensing phenomena. This new proposed irradiation facility allows materials to be irradiated without concern for HFIR coolant contamination (from specimen failures) as it uses a separate coolant, that is isolated (except thermally) from the HFIR primary coolant. (authors)

42 ENGINEERING↗

Large Eddy Simulations for a Helical Coil Steam Generator

The desire for scalable power plants in remote locations and specialized applications has brought forth the small modular reactor (SMR). Now, smaller light water reactors are seen as viable means for meeting global energy requirements. Generally, straight or U-shape tubes are used to exchange heat from the primary to secondary coolant; however this is not ideal when size is a criterion. Helical coil steam generators (HCSGs) are advantageous for SMRs due to their enhanced heat transfer in compact spaces. Still, there is the concern of safety as steam generator tubes could rupture due to vibrations and fatigue on the material. Understanding flow characteristics and quantifying pressures for these tubes are important components for the design of safety and efficiency in these steam generators. The current study uses the spectral element computational fluid dynamic (CFD) code, Nek5000, to develop large eddy simulations (LES) for validation against experiments that will be conducted at Texas A and M University. Time-averaged pressure data will be compared with pressure tap readings, and velocity profile with particle image velocimetry (PIV) measurements. The presented preliminary results investigate the differences between 5.-, 7.-, and 9.-order polynomial simulations. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Comparison of MAVRIC/MONACO and TRIPOLI-4{sup R} simulations of the LLNL pulsed spheres benchmark experiments - 25403

Simulations of the Lawrence Livermore Pulsed Spheres with MAVRIC/Monaco and TRIPOLI-4{sup R} are presented. Both codes use ENDF/B-VII.1 cross section data, but TRIPOLI-4{sup R} also uses cross section data based on JEFF-3.1.1. The MAVRIC/Monaco simulations were performed with the SCALE 6.2.2 release while the TRIPOLI-4{sup R} simulations used an internal development version of the code. For the most part, the simulated and measured neutron counts agree within 30%. Simulated gamma flux data is compared, as well. There are no measured gamma data. The agreement between the simulated gamma flux spectra is often within 10% or less, but there some notable differences, especially when comparing simulations using ENDF/B-VII.1 and JEFF 3.1.1 based cross section data. The comparison of photon simulations suggests that improvements are needed in the cross-section data, cross section processing codes, and/or transport codes and gamma measurement data is needed for experimental validation. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗

Secondary Cosmic Ray Particles Due to GCR Interactions in the Earth's Atmosphere

Primary GCR interact with the Earth's atmosphere originating atmospheric showers, thus giving rise to fluxes of secondary particles in the atmosphere. Electromagnetic and hadronic interactions interplay in the production of these particles, whose detection is performed by means of complementary techniques in different energy ranges and at different depths in the atmosphere, down to the Earth's surface. Monte Carlo codes are essential calculation tools which can describe the complexity of the physics of these phenomena, thus allowing the analysis of experimental data. However, these codes are affected by important uncertainties, concerning, in particular, hadronic physics at high energy. In this paper we shall report some results concerning inclusive particle fluxes and atmospheric shower properties as obtained using the FLUKA transport and interaction code. Some emphasis will also be given to the validation of the physics models of FLUKA involved in these calculations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Alternative materials to cadmium for neutron absorbers in safeguards applications

Cadmium is increasingly difficult to use in safeguards applications because of rising cost and increased safety regulations. This work examines the properties of two materials produced by Ceradyne, inc. that present alternatives to cadmium for neutron shielding. The first is an aluminum metal doped with boron and the second is a boron carbide powder, compressed into a ceramic. Both are enriched in the {sup 10}B isotope. Two sheets of boron doped aluminum (1.1 mm and 5.2mm thick) and one sheet of boron carbide (8.5mm thick) were provided by Ceradyne for testing. An experiment was designed to test the neutron absorption capabilities of these three sheets against two different thicknesses of cadmium (0.6mm and 1.6mm thick). The thinner piece of aluminum boron alloy (1.1mm) performed as well as the cadmium pieces at absorbing neutrons. The thicker aluminum-boron plate provided more shielding than the cadmium sheets and the boron carbide performed best by a relatively large margin. Monte Carlo N-Particle eXtended (MCNPX) transport code modeling of the experiment was performed to provide validaLed computational tools for predicting the behavior of systems in which these materials may be incorporated as alternatives to cadmium. MCNPX calculations predict that approximately 0.17mm of the boron carbide is equivalent to 0.6mm of cadmium. There are drawbacks to these materials that need to be noted when considering using them as replacements for cadmium. Notably, they may need to be thicker than cadmium, and are not malleable, requiring machining to fit any curved forms.

35↗

Development of Process Flowsheets for the Recovery of Metals by Solvent Extraction to Recycle Battery Materials: Evaluation of Application of AMUSE Code. Final CRADA Report

RSR Technologies (RSRT) wished to investigate the use of the AMUSE solvent extraction code, housed at Argonne National Laboratory (ANL) to evaluate the recycling of battery cells for the reclamation of metal values. The modeling studies were undertaken by the group at ANL to evaluate several separation schemes for battery metals using solvent extraction. These studies would develop a framework to be experimentally validated at RSRT at its facility in Dallas, TX. The AMUSE code modeling work would speed the development of recovery flowsheets for spent batteries.

25 ENERGY STORAGE↗

Experimental and numerical studies of seismic fluid-structure interaction in a base-supported cylindrical vessel

Seismic design and qualification of advanced reactors will rely heavily on the use of verified and validated numerical models capable of capturing the interaction of the vessel, its contained fluid, and the internal equipment: fluid-structure interaction (FSI) analysis. Analytical solutions can be used for preliminary sizing and design of such vessels but their application is limited to simple geometries and boundary conditions, and small amplitude, translational (and rotational) inputs. To validate numerical models for seismic FSI analysis in finite element codes, a comprehensive set of experiments was performed on a liquid-filled cylindrical vessel, using a 6 degree-of-freedom earthquake simulator. Results in terms of sloshing frequency, damping ratio in sloshing modes, and hydrodynamic responses (wave height, hydrodynamic pressure, base shear, and base moment) for multi-directional earthquake simulator inputs are reported and compared with analytical solutions for liquid-filled vessels. The impact of seismic (base) isolation on hydrodynamic responses was studied using earthquake simulator inputs generated using a virtual isolation system. Data from the experiments are used to validate a numerical model of the fluid-filled vessel using the Arbitrary Lagrangian Eulerian (ALE) solver in the commercial finite element program LS-DYNA. Validation studies are presented for multi-directional seismic inputs, including rocking motions. Lagrangian modeling approaches using an elastic material formulation for the fluid are also investigated and their limitations and possible applications are identified. Here, the results are broadly applicable to the seismic response of base supported, liquid-filled vessels.

58 GEOSCIENCES↗

A code-to-code benchmark for magneto-convection in a horizontal duct

Liquid metals and magnetic fields are used in many technical applications such as metallurgy, crystal growth and nuclear fusion reactors. When an electrically conducting fluid moves in a magnetic environment, electric currents and electromagnetic forces are generated that affect velocity and pressure losses in the flow. These magnetohydrodynamic (MHD) interactions have to be investigated to optimize the engineering processes. The characteristics of MHD flows depend on the geometrical configuration, the strength of the applied magnetic field, the electrical properties of fluid and structural materials and the thermal conditions. In the so-called blankets for fusion reactors, where liquid metals are used to breed the plasma fuel component tritium and to extract the generated heat, magneto-convective flows play a crucial role in determining heat and mass transfer. Therefore, the availability of numerical codes to simulate this type of flow is mandatory and their validation is a necessary step to guarantee the reliability of the results. For that reason, a benchmark problem has been defined to simulate liquid metal flows in a horizontal rectangular duct heated from below and exposed to a non-uniform magnetic field. Results obtained by five research groups using different codes are compared.

benchmark↗

The GENIE Neutrino Monte Carlo Generator

GENIE is a new neutrino event generator for the experimental neutrino physics community. The goal of the project is to develop a `canonical' neutrino interaction physics Monte Carlo whose validity extends to all nuclear targets and neutrino flavors from MeV to PeV energy scales. Currently, emphasis is on the few-GeV energy range, the challenging boundary between the non-perturbative and perturbative regimes, which is relevant for the current and near future long-baseline precision neutrino experiments using accelerator-made beams. The design of the package addresses many challenges unique to neutrino simulations and supports the full life-cycle of simulation and generator-related analysis tasks. GENIE is a large-scale software system, consisting of 120,000 lines of C++ code, featuring a modern object-oriented design and extensively validated physics content. The first official physics release of GENIE was made available in August 2007, and at the time of the writing of this article, the latest available version was v2.4.4.

Andreopoulos, C.↗

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗

On the Validity of Certain Approximations Used in the Modeling of Nuclear EMP

The legacy codes developed for the modeling of EMP, multiple scattering of Compton electrons has typically been modeled by the obliquity factor. A recent publication has examined this approximation in the context of the generated Compton current [W. A. Farmer and A. Friedman, IEEE Trans. Nucl. Sc. 62, 1695 (2015)]. Here, this previous analysis is extended to include the generation of the electromagnetic fields. Obliquity factor predictions are compared with Monte-Carlo models. In using a Monte-Carlo description of scattering, two distributions of scattering angles are considered: Gaussian and a Gaussian with a single-scattering tail. Additionally, legacy codes also neglect the radial derivative of the backward-traveling wave for computational efficiency. The neglect of this derivative improperly treats the backward-traveling wave. Moreover, these approximations are examined in the context of a high-altitude burst, and it is shown that in comparison to more complete models, the discrepancy between field amplitudes is roughly two to three percent and between rise-times, 10%. Finally, it is concluded that the biggest factor in determining the rise time of the signal is not the dynamics of the Compton current, but is instead the conductivity.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Los Alamos and Lawrence Livermore National Laboratories Code-to-Code Comparison of Inter Lab Test Problem 1 for Asteroid Impact Hazard Mitigation

The NNSA Laboratories have entered into an interagency collaboration with the National Aeronautics and Space Administration (NASA) to explore strategies for prevention of Earth impacts by asteroids. Assessment of such strategies relies upon use of sophisticated multi-physics simulation codes. This document describes the task of verifying and cross-validating, between Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL), modeling capabilities and methods to be employed as part of the NNSA-NASA collaboration. The approach has been to develop a set of test problems and then to compare and contrast results obtained by use of a suite of codes, including MCNP, RAGE, Mercury, Ares, and Spheral. This document provides a short description of the codes, an overview of the idealized test problems, and discussion of the results for deflection by kinetic impactors and stand-off nuclear explosions.

79 ASTRONOMY AND ASTROPHYSICS↗