Search NASA⌕ Search

SEARCH · Search NASA

Results for “etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Fabrication of submicron La{sub 2-x}Sr{sub x}CuO{sub 4} intrinsic Josephson junction stacks

Intrinsic Josephson junction (IJJ) stacks of cuprate superconductors have potential to be implemented as intrinsic phase qubits working at relatively high temperatures. We report success in fabricating submicron La{sub 2-x}Sr{sub x}CuO{sub 4} (LSCO) IJJ stacks carved out of single crystals. We also show a new fabrication method in which argon ion etching is performed after focused ion beam etching. As a result, we obtained an LSCO IJJ stack in which resistive multibranches appeared. It may be possible to control the number of stacked IJJs with an accuracy of a single IJJ by developing this method.

36 MATERIALS SCIENCE↗

Temporally resolved ion velocity distribution measurements in a radio-frequency plasma sheath

The ion velocity distribution function (IVDF) above and within a radio-frequency (RF) biased plasma sheath is studied experimentally with a pulsed laser-induced fluorescence diagnostic in an industrial plasma etch tool. Temporally resolved measurements taken at eight different phases of the 2.2 MHz bias waveform show that the ion dynamics vary dramatically throughout the RF cycle (the ratio of the average ion transit time through the sheath to the RF period is {tau}{sub ion}/{tau}{sub RF} = 0.3). The position of the presheath/sheath edge is constant throughout the RF cycle and the time-averaged ion flux is conserved within the sheath region. The characteristic bimodal structure of the time-averaged ion distributions found in previous experiments is observed to arise from the time-dependent ion dynamics, in accord with existing theory. The large temporal variation of the IVDF has implications for the plasma chemistry and etching quality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Incorporation of the stress concentration slots into the flexures for a high-performance microaccelerometer

Presented in this paper is a development of a high-performance piezoresistive microaccelerometer based on the slot etching in the quad flexures for the vibration detection of high speed spindle. The proposed structure consists of a proof mass supported by four thin flexures with slots etched in the middle. Boron diffused piezoresistors located near the stress concentration regions are used for sensing the localized stress resulting from the incorporation of the slots into the flexures. Theoretical analysis and finite element analysis show satisfactory results of an improved sensitivity and favorable natural frequency higher than 10 kHz, conforming to the initial design requirements. The microfabrication techniques are described to prototype the two accelerometer chips, one with slots and the other one without slots. The tested microaccelerometers with 3 V DC power supply show an average sensitivity of 0.424 mV/g normal to the proof mass plane, increased by 60.6% than the ones without slots. An average transverse sensitivity is found to be 9.2 {mu}V/g along X axis and 14.2 {mu}V/g along Y axis, either of which is less than 3.5% of prime-axis sensitivity. Concerning the resonant frequency, dynamic experiment shows about 12.46 kHz and is available for the proposed design with a tiny loss of 3.5% compared with the quad-beam design. When taking the product of sensitivity and natural frequency as judgment criteria, an inspiring increase by 28.6% of the figure of merit is accomplished for the proposed accelerometer. Overall, the findings of this study confirm the feasibility of incorporating slots into the conventional configurations to improve the sensor sensitivity while maintaining a comparatively high natural frequency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Preparation of the spacer for narrow electrode gap configuration in ionization-based gas sensor

Carbon nanotubes (CNTs) have started to be developed as the sensing element for ionization-based gas sensors due to the demand for improved sensitivity, selectivity, stability and other sensing properties beyond what can be offered by the conventional ones. Although these limitations have been overcome, the problems still remain with the conventional ionization-based gas sensors in that they are bulky and operating with large breakdown voltage and high temperature. Recent studies have shown that the breakdown voltage can be reduced by using nanostructured electrodes and narrow electrode gap. Nanostructured electrode in the form of aligned CNTs array with evenly distributed nanotips can enhance the linear electric field significantly. The later is attributed to the shorter conductivity path through narrow electrode gap. The paper presents the study on the design consideration in order to realize ionization based gas sensor using aligned carbon nanotubes array in an optimum sensor configuration with narrow electrode gap. Several deposition techniques were studied to deposit the spacer, the key component that can control the electrode gap. Plasma spray deposition, electron beam deposition and dry oxidation method were employed to obtain minimum film thickness around 32 {mu}m. For plasma spray method, sand blasting process is required in order to produce rough surface for strong bonding of the deposited film onto the surface. Film thickness, typically about 39 {mu}m can be obtained. For the electron beam deposition and dry oxidation, the film thickness is in the range of nanometers and thus unsuitable to produce the spacer. The deposited multilayer film consisting of copper, alumina and ferum on which CNTs array will be grown was found to be removed during the etching process. This is attributed to the high etching rate on the thin film which can be prevented by reducing the rate and having a thicker conductive copper film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chronocoulometry for quantitative control of mass removal in micro-structures and sensors

In this work, tungsten wires have been etched in a KOH electrolyte solution. Based on the oxidation state of the electrolytic dissolution reaction's product and time integration of the Faradaic current produced during the reaction, this method is capable of providing a direct measurement of the change in mass of a structure from anodic dissolution. To assess the application of this process for controlled mass removal spanning sub-micrograms to milligrams, two experimental studies and accompanying uncertainty analyses have been undertaken. In the first of these, 5 tungsten wires of length 30 mm were used to remove mass values ranging from 50 to 350 {mu}g. Uncertainty estimates indicate relative combined standard uncertainties of less than 0.3% in the mass changes determined from the measurement of Faradaic current. Comparison of the mass change determined using the electrolytic method, and using a precision ultra-microbalance agreed within this uncertainty. The charge-based method was then applied to modify the dynamic characteristics of a quartz tuning fork oscillator. In these experiments, tungsten fiber attached to one tine of the oscillator was etched in 5 {mu}g increments up to 120 {mu}g of total removed mass. In general, frequency shifts of 2.8 Hz{center_dot}{mu}g{sup -1} were observed, indicating sub-microgram resolution for the characterization of probes based on frequency shift and charge-based mass measurement. Taken together, this study provides the basis for a precision method for determining changes in mass based on electrical measurements from an electrochemical system. The utility of this technique is demonstrated through controlled modification of the dynamic properties of a mechanical oscillator.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Revisiting the mechanisms involved in Line Width Roughness smoothing of 193 nm photoresist patterns during HBr plasma treatment

HBr plasma treatments are widely used in nanoscale lithographic technologies to increase the plasma etch resistance of 193 nm photoresist masks as well as to decrease their Line Width Roughness (LWR). VUV irradiation of the photoresist is known to play a major role in this process by inducing polymer chains rearrangement and finally LWR reduction. However, in the plasma environment (i.e., with radical and ion bombardment), the interaction layer formed at the resist surface perturbs this mechanism and a lower LWR reduction is achieved compared to VUV only treatment. So far the nature of the interaction layer, its formation mechanism and its relation with the resist pattern LWR were all unclear. In this paper, we show that a graphite-like layer is formed on the resist patterns by the redeposition of carbon-based species originating from the plasma dissociation of outgassed photo-etched resist moieties. We show that the presence of this layer inhibits the LWR minimization and causes an increase in the LWR when it becomes thick enough (i.e., a few nanometers). We present evidences that the difference in the mechanical properties of the graphite-like top layer which coats the resist patterns and the bulk of the resist patterns is correlated to the LWR after plasma treatment. We can conclude that the optimization of an HBr cure process relies on the minimization of the carbon redeposition while keeping a significant VUV light flux and we show that this can be achieved by using pulsed plasma processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Identification of As-vacancy complexes in Zn-diffused GaAs

We have used positron annihilation spectroscopy to study the introduction of point defects in Zn-diffused semi-insulating GaAs. The diffusion was performed by annealing the samples for 2 h at 950 Degree-Sign C. The samples were etched in steps of 7 {mu}m. Both Doppler broadening using slow positron beam and lifetime spectroscopy studies were performed after each etching step. Both techniques showed the existence of vacancy-type defects in a layer of about 45 {mu}m. Secondary ion mass spectroscopy measurements illustrated the presence of Zn at high level in the sample almost up to the same depth. Vacancy-like defects as well as shallow positron traps were observed by lifetime measurements. We distinguish two kinds of defects: As vacancy belongs to defect complex, bound to most likely one Zn atom incorporated on Ga sublattice, and negative-ion-type positron traps. Zn acceptors explained the observation of shallow traps. The effect of Zn was evidenced by probing GaAs samples annealed under similar conditions but without Zn treatment. A defect-free bulk lifetime value is detected in this sample. Moreover, our positron annihilation spectroscopy measurements demonstrate that Zn diffusion in GaAs system is governed by kick-out mechanism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface and interfacial reaction study of half cycle atomic layer deposited HfO{sub 2} on chemically treated GaSb surfaces

An in situ half-cycle atomic layer deposition/X-ray photoelectron spectroscopy (XPS) study was conducted in order to investigate the evolution of the HfO{sub 2} dielectric interface with GaSb(100) surfaces after sulfur passivation and HCl etching, designed to remove the native oxides. With the first pulses of tetrakis(dimethylamido)hafnium(IV) and water, a decrease in the concentration of antimony oxide states present on the HCl-etched surface is observed, while antimony sulfur states diminished below the XPS detection limit on sulfur passivated surface. An increase in the amount of gallium oxide/sulfide is seen, suggesting oxygen or sulfur transfers from antimony to gallium during antimony oxides/sulfides decomposition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improved efficiency of photoconductive THz emitters by increasing the effective contact length of electrodes

We study the effect of a surface modification at the interface between metallic electrodes and semiconducting substrate in Semi-Insulating GaAs (SI-GaAs) based photoconductive emitters (PCE) on the emission of Tera-Hertz (THz) radiation. We partially etch out a 500 nm thick layer of SI-GaAs in grating like pattern with various periods before the contact deposition. By depositing the electrodes on the patterned surface, the electrodes follow the contour of the grating period. This increases the effective contact length of the electrodes per unit area of the active regions on the PCE. The maxima of the electric field amplitude of the THz pulses emitted from the patterned surface are enhanced by up to more than a factor 2 as compared to an un-patterned surface. We attribute this increase to the increase of the effective contact length of the electrode due to surface patterning.

36 MATERIALS SCIENCE↗

Analysis of surface integrity of grinded gears using Barkhausen noise analysis and x-ray diffraction

The contribution is focused to present results of study grinded gears made of 18CrNiMo7-6 steel used in the wind power plant for support (service) purposes. These gears were case-hardened due to standard hard case and soft core formation. This heat treatment increases wear resistance and fatigue strength of machine parts. During serial production some troubles with surface integrity have occurred. When solving complex problems lots of samples were prepared. For grinding of gears were used different parameters of cutting speed, number of material removal and lots from different subsuppliers. Material characterization was carried out using Barkhausen noise analysis (BNA) device; X-ray diffraction (XRD) measurement of surface residual stresses was done as well. Depth profile of measured characteristics, e.g. magnetoelastic parameter and residual stress was obtained by step by step layers' removing using electrolytic etching. BNA software Viewscan was used to measure magnetizing frequency sweep (MFS) and magnetizing voltage sweep (MVS). Scanning of Magnetoelastic parameter (MP) endwise individual teeth were also carried out with Viewscan. These measurements were done to find problematic surface areas after grinding such as thermal damaged locations. Plots of the hardness and thickness of case-hardened layer on cross sections were measurered as well. Evaluation of structure of subsurface case-hardened layer and core was made on etched metallographic patterns. The aim of performed measurements was to find correlation between conditions of grinding, residual stresses and structural and magnetoelastic parameters. Based on correlation of measured values and technological parameters optimizing the production of gears will be done.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fabrication of super-hydrophobic surfaces on aluminum alloy substrates by RF-sputtered polytetrafluoroethylene coatings

In this work, we present a method of fabricating super-hydrophobic surface on aluminum alloy substrate. The etching of aluminum surfaces has been performed using Beck's dislocation etchant for different time to create micrometer-sized irregular steps. An optimised etching time of 50 s is found to be essential before polytetrafluoroethylene (PTFE) coating, to obtain a highest water contact angle of 165±2° with a lowest contact angle hysteresis as low as 5±2°. The presence of patterned microstructure as revealed by scanning electron microscopy (SEM) together with the low surface energy ultrathin RF-sputtered PTFE films renders the aluminum alloy surfaces highly super-hydrophobic.

36 MATERIALS SCIENCE↗

A super-compact metamaterial absorber cell in L-band

A super-compact metamaterial absorber (SMA) unit cell in L band (1–2 GHz) is proposed, which is composed of a pair of electric ring resonator (ERR) and its complementary ERR (CERR) with a high dielectric substrate sandwiched in between. The CERR has a cross sectional area where approximately the etched copper foil in ERR is now retained, and the remaining region is now etched. In contract with quarter-wavelength (λ/4) thickness which is required for conventional absorbers, the largest in-plane dimension and thickness of the SMA cell are only λ/33 and λ/250, respectively, leading to a super compact cell volume. While traditionally the long straight wire is introduced in electric-LC resonators for increasing inductance, the CERR achieves similar inductance with much shorter lengths. Thus, its cell dimensions can be drastically reduced without compromising its performance. In addition, simulations together with an automated phase correction algorithm show that the SMA is a type of metamaterial possessing simultaneous negative electric permittivity (NEP) and negative magnetic permeability (NMP). Further the SMA has a very large imaginary part of the NEP and NMP, resulting in significantly large imaginary part of the refractive index at resonant frequency. These properties are well suited to design excellent absorbers. In addition, numerical results demonstrate that the maximum absorption coefficient of the SMA can reach greater than 99% at resonant frequency, and the full-width half-maximum is roughly 1% of the operating frequency, and a wide incident angle of ±49° over 90% absorption. Meanwhile, it is pointed out that this type of absorber is rather sensitive to polarization characteristic of the incident electromagnetic wave.

36 MATERIALS SCIENCE↗

Evidence of a Love wave bandgap in a quartz substrate coated with a phononic thin layer

This paper presents a numerical and experimental study of Love wave propagation in a micro-fabricated phononic crystal (PC) structure consisting of a 2D, periodically etched silica film deposited on a quartz substrate. The dispersion characteristics of Love waves in such a phononic structure were analyzed with various geometric parameters by using complex band structure calculations. For the experiment, we adopted reactive-ion etching with electron-beam lithography to fabricate a submicrometer phononic structure. The measured results exhibited consistency with the numerical prediction. The results of this study may serve as a basis for developing PC-based Love wave devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical bandgap of ultra-thin amorphous silicon films deposited on crystalline silicon by PECVD

An optical study based on spectroscopic ellipsometry, performed on ultrathin hydrogenated amorphous silicon (a-Si:H) layers, is presented in this work. Ultrathin layers of intrinsic amorphous silicon have been deposited on n-type mono-crystalline silicon (c-Si) wafers by plasma enhanced chemical vapor deposition (PECVD). The layer thicknesses along with their optical properties –including their refractive index and optical loss- were characterized by spectroscopic ellipsometry (SE) in a wavelength range from 250 nm to 850 nm. The data was fitted to a Tauc-Lorentz optical model and the fitting parameters were extracted and used to compute the refractive index, extinction coefficient and optical bandgap. Furthermore, the a-Si:H film grown on silicon was etched at a controlled rate using a TMAH solution prepared at room temperature. The optical properties along with the Tauc-Lorentz fitting parameters were extracted from the model as the film thickness was reduced. The etch rate for ultrathin a-Si:H layers in TMAH at room temperature was found to slow down drastically as the c-Si interface is approached. From the Tauc-Lorentz parameters obtained from SE, it was found that the a-Si film exhibited properties that evolved with thickness suggesting that the deposited film is non-homogeneous across its depth. It was also found that the degree of crystallinity and optical (Tauc) bandgap increased as the layers were reduced in thickness and coming closer to the c-Si substrate interface, suggesting the presence of nano-structured clusters mixed into the amorphous phase for the region close to the crystalline silicon substrate. Further results from Atomic Force Microscopy and Transmission Electron Microscopy confirmed the presence of an interfacial transitional layer between the amorphous film and the underlying substrate showing silicon nano-crystalline enclosures that can lead to quantum confinement effects. Quantum confinement is suggested to be the cause of the observed increase in the optical bandgap of a-Si:H films close to the a-Si:H/cSi interface.

36 MATERIALS SCIENCE↗

Broadband antireflection and absorption enhancement of ultrathin silicon solar microcells enabled with density-graded surface nanostructures

Density-graded surface nanostructures are implemented on ultrathin silicon solar microcells by silver-nanoparticle-catalyzed wet chemical etching to enable near-zero surface reflection over a broad wavelength range of incident solar spectrum as well as non-zeroth order diffraction and light trapping for longer wavelength photons, thereby achieving augmented photon absorption for ultrathin silicon microcells in a simple, cost-effective manner. The increase of absorbed photon flux through the “black silicon (b-Si)” surface translates directly into the corresponding enhancement of photovoltaic performance, where 5.7-μm b-Si microcells with the rational design of device configuration exhibit improved energy conversion efficiency by 148% and 50% with and without a diffuse backside reflector, respectively, compared to devices from the bare silicon without b-Si implementation. Systematic studies on nanostructured morphology, optical and electrical properties of b-Si microcells, together with semi-empirical numerical modeling of photon absorption, provide key aspects of underlying materials science and physics.

14 SOLAR ENERGY↗

Optical waveguiding properties into porous gallium nitride structures investigated by prism coupling technique

In order to modulate the refractive index and the birefringence of Gallium Nitride (GaN), we have developed a chemical etching method to perform porous structures. The aim of this research is to demonstrate that optical properties of GaN can be tuned by controlling the pores density. GaN films are prepared on sapphire by metal organic chemical vapor deposition and the microstructure is characterized by transmission electron microscopy, and scanning electron microscope analysis. Optical waveguide experiment is demonstrated here to determine the key properties as the ordinary (n{sub 0}) and extraordinary (n{sub e}) refractive indices of etched structures. We report here the dispersion of refractive index for porous GaN and compare it to the bulk material. We observe that the refractive index decreases when the porous density p is increased: results obtained at 0.975 μm have shown that the ordinary index n{sub 0} is 2.293 for a bulk layer and n{sub 0} is 2.285 for a pores density of 20%. This value corresponds to GaN layer with a pore size of 30 nm and inter-distance of 100 nm. The control of the refractive index into GaN is therefore fundamental for the design of active and passive optical devices.

36 MATERIALS SCIENCE↗

Improvement of bias-stability in amorphous-indium-gallium-zinc-oxide thin-film transistors by using solution-processed Y{sub 2}O{sub 3} passivation

We demonstrate back channel improvement of back-channel-etch amorphous-indium-gallium-zinc-oxide (a-IGZO) thin-film transistors by using solution-processed yttrium oxide (Y{sub 2}O{sub 3}) passivation. Two different solvents, which are acetonitrile (35%) + ethylene glycol (65%), solvent A and deionized water, solvent B are investigated for the spin-on process of the Y{sub 2}O{sub 3} passivation—performed after patterning source/drain (S/D) Mo electrodes by a conventional HNO{sub 3}-based wet-etch process. Both solvents yield devices with good performance but those passivated by using solvent B exhibit better light and bias stability. Presence of yttrium at the a-IGZO back interface, where it occupies metal vacancy sites, is confirmed by X-ray photoelectron spectroscopy. The passivation effect of yttrium is more significant when solvent A is used because of the existence of more metal vacancies, given that the alcohol (65% ethylene glycol) in solvent A may dissolve the metal oxide (a-IGZO) through the formation of alkoxides and water.

36 MATERIALS SCIENCE↗

Near-infrared emission from mesoporous crystalline germanium

Mesoporous crystalline germanium was fabricated by bipolar electrochemical etching of Ge wafer in HF-based electrolyte. It yields uniform mesoporous germanium layers composed of high density of crystallites with an average size 5-7 nm. Subsequent extended chemical etching allows tuning of crystallites size while preserving the same chemical composition. This highly controllable nanostructure exhibits photoluminescence emission above the bulk Ge bandgap, in the near-infrared range (1095-1360nm) with strong evidence of quantum confinement within the crystallites.

36 MATERIALS SCIENCE↗