Search NASA⌕ Search

SEARCH · Search NASA

Results for “force method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Customized atomic force microscopy probe by focused-ion-beam-assisted tip transfer

We present a technique for transferring separately fabricated tips onto tipless atomic force microscopy (AFM) cantilevers, performed using focused ion beam-assisted nanomanipulation. This method addresses the need in scanning probe microscopy for certain tip geometries that cannot be achieved by conventional lithography. For example, in probing complex layered materials or tall biological cells using AFM, a tall tip with a high-aspect-ratio is required to avoid artifacts caused by collisions of the tip's sides with the material being probed. We show experimentally that tall (18 μm) cantilever tips fabricated by this approach reduce squeeze-film damping, which fits predictions from hydrodynamic theory, and results in an increased quality factor (Q) of the fundamental flexural mode. We demonstrate that a customized tip's well-defined geometry, tall tip height, and aspect ratio enable improved measurement of elastic moduli by allowing access to low-laying portions of tall cells (T lymphocytes). This technique can be generally used to attach tips to any micromechanical device when conventional lithography of tips cannot be accomplished.

36 MATERIALS SCIENCE↗

Highly conductive indium nanowires deposited on silicon by dip-pen nanolithography

In this paper, we developed a new dip-pen nanolithography (DPN) method. Using this method, we fabricated conductive nanowires with diameters of 30–50 nm on silicon substrates. To accomplish this, indium was transferred from an atomic force microscopy tip to the surface by applying a potential difference between the tip and substrate. The fabricated indium nanowires were several micrometers in length. Unlike thermal DPN, our DPN method hardly oxidized the indium, producing nanowires with conductivities from 5.7 × 10{sup −3} to 4 × 10{sup −2} Ω cm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Triangle Method for Dense ReLU Layers [SWR-25-72]

This software is an implementation of the methods for initializing and training neural networks to be more efficient per parameter, described more fully below and in the related publication: In theory, depth should make a ReLU network EXPONENTIALLY more efficient by enabling it to produce an exponential number of piecewise linear sections in its output. This reasoning is largely based on the work of mathematicians that have hand-constructed networks that make good use of depth. In practice however, even very deep ReLU networks that have been randomly initialized will behave identically to their shallow counterparts - missing an entire exponential dimension of efficiency. The triangle method is a first attempt at realizing the exponential potential of deep networks. Instead of randomly setting weights, we force pairs of neurons in each layer learn to build triangles (i.e. functions from [0,1] -> [0,1] that look like triangles). This is a very efficient pattern for generating lots of linear pieces because composing two triangular functions doubles the number of pieces with each composition. The triangle method is more than just a different initialization, it is a new paradigm of training. Instead of making direct updates to the matrix weights, we do an extra step of backpropagation to collect the derivatives of the loss function with respect to the shapes of the triangles, training them to tilt left or right. This process essentially holds the networks hand throughout the loss landscape and forces it to always use depth effectively by producing triangular shapes internally. This can produce several orders of magnitude of improvement on convex one-dimensional regression problems. Much more theoretical work is needed to realize its full potential beyond this context, but the implementation in this repository will still work in arbitrary numbers of dimensions. The file Triangle_Method.py is a generalized form of the method that will build each neuron its own custom 1-d convex activation function (with exponential efficiency). Example usage on one dimensional problems can be found in Example_Usage.ipynb and an example of using this in a real neural network can be found in Example_VGG16_CIFAR10.ipynb.

Milkert, Max [National Renewable Energy Laboratory↗

Constraining the Beam Neutrino MC Flux Using the MINOS ND Data

This document describes a method to handle correlated systematic uncertainties from hadron production on the beam spectrum by using the neutrino ·data from the MINOS detector. We have developed a tuning function which can be applied after the fact to the Monte Carlo to force agreement with the CC neutrino energy spectra observed in the near detector and the beam MC. The method relies on the flexible NuMI beam, which can be configured so as to selectively sample pions. of different momenta and angles off the target. There is sufficient information in the neutrino data in a detector like MINOS to deduce the portion of the underlying spectrum of hadrons off the NuMI target which contribute to the NuMI flux.

Kopp, Sacha [U. Texas, Austin (main)]↗

Coalescence Prevention Algorithm for Level Set Method

An algorithm to prevent or delay bubble coalescence for the level set (LS) method is presented. This novel algorithm uses the LS method field to detect when bubbles are in close proximity, indicating a potential coalescence event, and applies a repellent force to simulate the unresolved liquid drainage force. The model is introduced by locally modifying the surface tension force near the liquid film drainage area. The algorithm can also simulate the liquid drainage time of the thin film by controlling the length of time the increased surface tension has been applied. Thus, a new method of modeling bubble coalescence has been developed. Several test cases were designed to demonstrate the capabilities of the algorithm. The simulations, including a mesh study, confirmed the abilities to identify and prevent coalescence as well as implement the time tracking portion, with an additional 10–25% computational cost. Ongoing tests aim to verify the algorithm's functionality for simulations with different flow conditions, a ranging number of bubbles, and both structured and unstructured computational mesh types. Specifically, a bubble rising toward a free surface provides a test of performance and demonstrates the ability to consistently prevent coalescence. In addition, a two bubble case and a seven bubble case provide a more complex demonstration of how the algorithm performs for larger simulations. These cases are compared to much more expensive simulations capable of resolving the liquid film drainage (through very high local mesh resolution) to investigate how the algorithm replicates the liquid film drainage process.

Engineering↗

Modulating Transition Metal Reactivity with Force

The reactivity and selectivity of a transition metal catalyst is intimately related to its ligand-sphere geometry, and, in many cases, the ideal ligand geometry for one step of a catalytic cycle is poorly matched to the ideal ligand geometry for another. For this reason, methods for reversibly modulating ligand geometry on the time scale of catalytic turnover or monomer enchainment are highly desirable. Mechanical force represents a heretofore untapped approach to modulate catalyst geometry and/or reactivity, with the potential to do so on the timescale of catalytic turnover or monomer enchainment. Macroscopic mechanical forces are large, directional and localized to an extent that differentiates them from other forms of energy input such as heat or light. Here, in this Concept, we describe our efforts to address the fundamental challenges associated with force-modulated transition metal catalysis by employing molecular force probe ligands comprising a stiff stilbene photoswitch tethered to rotationally flexible biaryl bisphosphine ligand. Our efforts to date include the modulation of catalytic activity through force-mediated ligand perturbations, quantification of the force-coupled ligand effects on the energetics of elementary organometallic transformations, and evaluation of the mechanisms of force transduction in these systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coupled Mooring Analyses for the WEC-Sim Wave Energy Converter Design Tool: Preprint

A wave-energy-converter-specific time-domain modeling method (WEC-Sim) was coupled with a lumped-mass-based mooring model (MoorDyn) to improve its mooring dynamics modeling capability. This paper presents a verification and validation study on the coupled numerical method. First, a coupled model was built to simulate a 1/25 model scale floating power system connected to a traditional three-point catenary mooring with an angle of 120 between the lines. The body response and the tension force on the mooring lines at the fairlead in decay tests and under regular and irregular waves were examined. To validate and verify the coupled numerical method, the simulation results were compared to the measurements from a wave tank test and a commercial code (OrcaFlex). Second, a coupled model was built to simulate a two-body point absorber system with a chain-connected catenary system. The influence of the mooring connection on the point absorber was investigated. Overall, the study showed that the coupling of WEC-Sim and the MoorDyn model works reasonably well for simulating a floating system with practical mooring designs and predicting the corresponding dynamic loads on the mooring lines. Further analyses on improving coupling efficiency and the feasibility of applying the numerical method to simulate WEC systems with more complex mooring configuration are still needed.

16 TIDAL AND WAVE POWER↗

STRUCTURE OF NON-FORCE-FREE MAGNETIC FLUX ROPES IN AN AMBIENT MEDIUM

The structure of non-force-free equilibrium magnetic flux ropes in an ambient medium of specified pressure p{sub a} is studied. A flux rope is a self-organized magnetized plasma structure consisting of a localized channel of electric current and the magnetic field arising from this current. An analytic method is developed to obtain one-dimensional equilibrium solutions satisfying c {sup -1} J Multiplication-Sign B - {nabla}p = 0 subject to the requirements that (1) all physical quantities be nonsingular and continuous, (2) pressure p(r) be physically admissible-real and non-negative, and (3) the magnetic field profile have ''minimum complexity''. The solutions are shown to be characterized by two parameters, B{sup *}{sub t}{identical_to} B-bar{sub t}/(8{pi}p{sub a}){sup 1/2} and B*{sub p} {identical_to} B{sub pa} /(8{pi}p{sub a} ){sup 1/2}, where B-bar{sub t} is the toroidal (axial) field averaged over the cross-sectional radius a and B{sub pa} is the poloidal (azimuthal) field at the edge of the current channel (r = a). The physical constraint on pressure defines equilibrium boundaries in the B*{sub t}-B*{sub p} space beyond which no physical solutions exist. The method is illustrated with a number of families of solutions governed by distinct physical constraints. The force-free limit with p{sub a} {ne} 0 is investigated and is found to be characterized by plasma {beta} = {infinity}. The local Alfven speed V{sub A} and plasma {beta} are computed. The results are scale-invariant.

79 ASTRONOMY AND ASTROPHYSICS↗

Biodiesel Impact on Engine Lubricant Dilution During Active Regeneration of Aftertreatment Systems

Experiments were conducted with ultra low sulfur diesel (ULSD) and 20% biodiesel blends (B20) to compare lube oil dilution levels and lubricant properties for systems using late in-cylinder fuel injection for aftertreatment regeneration. Lube oil dilution was measured by gas chromatography (GC) following ASTM method D3524 to measure diesel content, by Fourier transform infrared (FTIR) spectrometry following a modified ASTM method D7371 to measure biodiesel content, and by a newly developed back-flush GC method that simultaneously measures both diesel and biodiesel. Heavy-duty (HD) engine testing was conducted on a 2008 6.7L Cummins ISB equipped with a diesel oxidation catalyst (DOC) and diesel particle filter (DPF). Stage one of engine testing consisted of 10 consecutive repeats of a forced DPF regeneration event. This continuous operation with late in-cylinder fuel injection served as a method to accelerate lube-oil dilution. Stage two consisted of 16 hours of normal engine operation over a transient test cycle, which created an opportunity for any accumulated fuel in the oil sump to evaporate. Light duty (LD) vehicle testing was conducted on a 2010 VW Jetta equipped with DOC, DPF and a NOx storage catalyst (NSC). Vehicle testing comprised approximately 4,000 miles of operation on a mileage-accumulation dynamometer (MAD) using the U.S. Environmental Protection Agency's Highway Fuel Economy Cycle because of the relatively low engine oil and exhaust temperatures, and high DPF regeneration frequency of this cycle relative to other cycles examined. Comparison of the lube oil dilution analysis methods suggests that D3524 does not measure dilution by biodiesel. The new back-flush GC method provided analysis for both diesel and biodiesel, in a shorter time and with lower detection limit. Thus all lube oil dilution results in this paper are based on this method. Analysis of the HD lube-oil samples showed only 1.5% to 1.6% fuel dilution for both fuels during continuous operation under DPF regeneration events. During the second stage of HD testing, the ULSD lube-oil dilution levels fell from 1.5% to 0.8%, while for B20, lube-oil dilution levels fell from 1.6% to 1.0%, but the fuel in the oil was 36% biodiesel. For the LD vehicle tests, the frequency of DPF regeneration events was observed to be the same for both ULSD and B20. No significant difference between the two fuels' estimated soot loading was detected by the engine control unit (ECU), although a 23% slower rate of increase in differential pressure across DPF was observed with B20. It appears that the ECU estimated soot loading is based on the engine map, not taking advantage of the lower engine-out particulate matter from the use of biodiesel. After 4,000 miles of LD vehicle operation with ULSD, fuel dilution in the lube-oil samples showed total dilution levels of 4.1% diesel. After 4,000 miles of operation with B20, total fuel in oil dilution levels were 6.7% consisting of 3.6% diesel fuel and 3.1% biodiesel. Extrapolation to the 10,000-mile oil drain interval with B20 suggests that the total fuel content in the oil could reach 12%, compared to 5% for operation on ULSD. Analysis of the oil samples also included measurement of total acid number, total base number, viscosity, soot, metals and wear scar; however, little difference in these parameters was noted.

09 BIOMASS FUELS↗

The behavior of methane–water mixtures under elevated pressures from simulations using many-body potentials

Non-polarizable empirical potentials have been proven to be incapable of capturing the mixing of methane–water mixtures at elevated pressures. Although density functional theory-based ab initio simulations may circumvent this discrepancy, they are limited in terms of the relevant time and length scales associated with mixing phenomena. Here, we show that the many-body MB-nrg potential, designed to reproduce methane–water interactions with coupled cluster accuracy, successfully captures this phenomenon up to 3 GPa and 500 K with varying methane concentrations. Two-phase simulations and long time scales that are required to fully capture the mixing, affordable due to the speed and accuracy of the MBX software, are assessed. Constructing the methane–water equation of state across the phase diagram shows that the stable mixtures are denser than the sum of their parts at a given pressure and temperature. As a result, we find that many-body polarization plays a central role, enhancing the induced dipole moments of methane by 0.20 D during mixing under pressure. Overall, the mixed system adopts a denser state, which involves a significant enthalpic driving force as elucidated by a systematic many-body energy decomposition analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simple Hybrid Sea Ice Nudging Method for Improving Control Over Partitioning of Sea Ice Concentration and Thickness

Abstract To assess the effect of ocean‐atmosphere coupling in the climate response to forced sea ice loss, the Polar Amplification Model Intercomparison Project protocol includes centennial coupled atmosphere‐ocean general circulation model simulations with imposed sea ice loss. The protocol, which specifies sea ice concentration and thickness distribution targets, does not prescribe a method for achieving them. Although different methods for imposing sea ice loss (or growth) in models have been documented, testing of the method‐dependence of the resulting climate responses has been limited. Achieving the targeted sea ice state has proven to be challenging using the so‐called ghost‐flux nudging method, which induces ice melt from below, as this method does not constrain the partitioning between thickness and concentration. We propose, describe and test a simple method that combines the advantages of direct sea ice nudging and ghost‐flux nudging. The hybrid nudging method better captures the partitioning between thickness and concentration while conserving total water content. We document how this novel sea ice constraining method reaches specific targets, enhances surface turbulent heat flux responses to sea ice loss, and induces tropospheric warming for both polar regions.

54 ENVIRONMENTAL SCIENCES↗

A Geometric Volume of Fluid-Based Multiphase Flow Solver Extension to the Reacting Flow Solver, PeleLM

A new algorithm is presented to simulate multiphase flows with surface tension in a pathway for spray combustion simulation. The algorithm combines capabilities from two open-source packages, including the interface reconstruction library (IRL), a library of computational geometry routines to enable the volume of fluid (VOF) method, and PeleLM, a solver for the reacting Navier-Stokes equations. Additionally, surface tension is implemented using the continuum surface force (CSF) model with an improved height function technique in the volume fraction field. Spurious errors in volume fraction arising from our combined strategy are corrected through a topology-based method that improves both numerical stability and accuracy. Multiple validation simulations are conducted, including (i) translations and rotations of Zalesak's disk, (ii) a stationary circular droplet with surface tension, (iii) an oscillating elliptical droplet, and (iv) three-dimensional deformation of a spherical droplet. Results indicate that the combined scheme retains the favorable properties of each of the component algorithms.

42 ENGINEERING↗

The Abrasion of Photovoltaic Glass: A Comparison of the Effects of Natural and Artificial Aging

Natural soiling and the subsequent requisite cleaning of photovoltaic (PV) modules result in abrasion damage to the cover glass. The durability of the front glass has important economic consequences, including determining the use of antireflective and/or antisoiling coatings as well as the method and frequency of operating maintenance (cleaning). The abrasion of coatings and glass has been explored in a field study, including the soiling-prone locations of Dubai (United Arab Emirates), Kuwait City (Kuwait), Mesa (Arizona), Mumbai (India), and Sacramento (California). Dry-brush-cleaned specimens will be compared to those subjected to artificial-brush testing. The characteristics of material integrity, surface energy, optical transmittance, surface roughness, and scratch size were examined using an optical microscope, contact goniometer (for water), spectrophotometer, interferometer, and atomic force microscope (AFM), respectively. The findings of this study will be used to provide feedback regarding the cleaning equipment, cleaning methods, and coatings used in the PV industry. The study here will also be used to aid in developing an abrasion standard for the PV industry.

14 SOLAR ENERGY↗

Synthesis, characterization and electrostatic properties of WS{sub 2} nanostructures

We report the direct growth of atomically thin WS{sub 2} nanoplates and nanofilms on the SiO{sub 2}/Si (300 nm) substrate by vapor phase deposition method without any catalyst. The WS{sub 2} nanostructures were systematically characterized by optical microscopy, scanning electron microscopy, Raman microscopy and atomic force microscopy. We found that growth time and growth temperature play important roles in the morphology of WS{sub 2} nanostructures. Moreover, by using Kelvin probe force microscopy, we found that the WS{sub 2} nanoplates exhibit uniform surface and charge distributions less than 10 mV fluctuations. Our results may apply to the study of other transition metal dichalcogenides by vapor phase deposition method.

36 MATERIALS SCIENCE↗

Accelerating molecular property calculations with nonorthonormal Krylov space methods

Here, we formulate Krylov space methods for large eigenvalue problems and linear equation systems that take advantage of decreasing residual norms to reduce the cost of matrix-vector multiplication. The residuals are used as subspace basis without prior orthonormalization, which leads to generalized eigenvalue problems or linear equation systems on the Krylov space. These nonorthonormal Krylov space (nKs) algorithms are favorable for large matrices with irregular sparsity patterns whose elements are computed on the fly, because fewer operations are necessary as the residual norm decreases as compared to the conventional method, while errors in the desired eigenpairs and solution vectors remain small. We consider real symmetric and symplectic eigenvalue problems as well as linear equation systems and Sylvester equations as they appear in configuration interaction and response theory. The nKs method can be implemented in existing electronic structure codes with minor modifications and yields speed-ups of 1.2-1.8 in typical time-dependent Hartree-Fock and density functional applications without accuracy loss. The algorithm can compute entire linear subspaces simultaneously which benefits electronic spectra and force constant calculations requiring many eigenpairs or solution vectors. The nKs approach is related to difference density methods in electronic ground state calculations, and particularly efficient for integral direct computations of exchange-type contractions. By combination with resolution-of-the-identity methods for Coulomb contractions, three- to fivefold speed-ups of hybrid time-dependent density functional excited state and response calculations are achieved.

74 ATOMIC AND MOLECULAR PHYSICS↗

Characteristics of microdomains and microdomain patterns recorded by electron beam irradiation on Y-cut LiNbO{sub 3} crystals

We present the results of investigations of planar domain patterns (isolated domains and domain gratings) fabricated by irradiation of the nonpolar Y-surface of LiNbO{sub 3} crystals by an electron beam (EB) incident normally onto the surface. The EB recorded domains were investigated using atomic force microscopy, confocal second harmonic generation microscopy, and chemical etching as an auxiliary method. The dependence of the domain characteristics on irradiation conditions (acceleration voltage U, EB current I, and irradiation time t{sub irr}) were determined. The length L{sub d} of both isolated domains and domain gratings along the polar axis Z grows linearly with t{sub irr} (at U, I = const) with no tending to saturation. The plots L{sub d}(t{sub irr}) obtained for U = 10 and 15 kV are practically identical, whereas the values of L{sub d} for U = 5 kV are essentially lower. The domain thickness T{sub d} along the Y-direction, i.e., the depth of the switched layer grows with acceleration voltage U. These results are discussed in terms of space-charge fields formation arising under EB irradiation of insulators. The linearity of L{sub d}(t{sub irr}) is accounted for by the frontal domain growth via the viscous friction law. The experimental dependence of T{sub d} on U supports the suggestion that the domain thickness is determined by the penetration depth R{sub e} of primary electrons, which in turn is governed by U. The difference in L{sub d}(t{sub irr}) plots for different U is accounted for by different electron emission σ. Indirect evidences of a defect structure modification in a thin surface layer with respect to the crystal bulk are obtained.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Application of atomic force microscopy in determining the fractal dimension of the mirror, mist, and hackle region of silica glass

Fractal analysis has been used as a method to study fracture surfaces of brittle materials. However, it has not been determined if the fractal characteristics of brittle materials is consistent throughout the fracture surface. Therefore, the fractal dimensional increment of the mirror, mist, and hackle regions of the fracture surface of silica glass was determined using atomic force microscopy. The fractal dimensional increment of the mirror region (0.17-0.26) was determined to be statistically greater than that for the mist (0.08-0.12) and hackle (0.08-0.13) regions. It is thought that the increase in the fractal dimensional increment is caused by a greater tortuosity in the mirror region due to, most likely, the slower crack velocity of the propagating crack in that region and that there is a point between the mirror and mist region at which the fractal dimension decreases and becomes constant. - Research Highlights: {yields} The fracture surface of silica glass does not have a constant fractal dimension. {yields} Mirror region has greater fractal dimension than mist or hackle region. {yields} Fractal dimension decreases between mirror and mist region. {yields} Greater fractal dimension could be due to slower crack velocity in mirror region.

36 MATERIALS SCIENCE↗