Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Adhesion measurement of highly-ordered TiO 2 nanotubes on Ti-6Al-4V alloy

Self-assembled nanotubular arrays on Ti alloys could be used for more effective implantable devices in various medical approaches. In the present work, the adhesion of TiO 2 nanotubes (TiO 2 NTs) on Ti-6Al-4V (Ti64) was investigated by laser spallation and scratch test techniques. At first, electrochemical anodization was performed in an ammonium fluoride solution dissolved in a 90:10 ethane-1,2-diol (ethylene glycol) and water solvent mixture. This process was performed at room temperature (23 °C) at a steady potential of 60 V for 1 h. Next, the TiO 2 nanotubes layer was heat-treated to improve the adhesion of the coating. The formation of self-organized TiO 2 nanotubes as well as the microstructural evolution, are strongly dependent on the processing parameters and subsequent annealing. From microscopic analysis, highly oriented arrays of TiO 2 nanotubes were grown by thermal treatment for 90 min at 500 °C. Further heat treatment above 500 °C led to the detachment of the nanotubes and the complete destruction of the nanotubes occurred at temperature above 700 °C. Scratch test analysis over a constant scratch length (1000 μm) indicated that the failure point was shifted from 247.4 to 557.9 μm while the adhesion strength was increased from ~862 to ~1814 mN after annealing at 500 °C. Finally, the adhesion measurement determined by laser spallation technique provided an intrinsic adhesion strength of 51.4 MPa for the TiO 2 nanotubes on the Ti64 substrate.

36 MATERIALS SCIENCE↗

A Percolating Path to Green Iron

About 1.9 gigatonnes of steel is produced every year emitting 7% (2.7 gigatonnes) of global CO 2 in the process. More than 50% of the CO 2 emissions come from a single step of steelmaking, known as ironmaking. Hydrogen based direct reduction (HyDR) of iron oxide to iron has emerged as an emissions free ironmaking alternative. However multi-scale phenomena ranging from nanometers to meters inside HyDR reactors exhibit detrimental microstructure evolution which resists gaseous transport of H 2 /H 2 O, slows reaction rates and disrupts continuous reactor operation. To resolve the conundrum between atomic and reactor scales, we devise a percolation-theory model to reconcile nanoscale porosity with macroscopic properties relevant to reactor design models. Using synchrotron nano X-ray computed-tomography, we quantify the evolution of pores in iron oxide pellets, and demonstrate how nano-scale pore networks influence micro and macro-scale flow properties such as permeability, diffusivity and tortuosity. Our new modeling framework bridges the gap between scales and offers the criteria to accelerate HyDR by at least 5x via feedstock-reactor synergies based on percolation.

Paul, Subhechchha↗

Determination of Thermal Expansion, Defect Formation Energy, and Defect-Induced Strain of α-U Via ab Initio Molecular Dynamics

Uranium (U) is often alloyed with molybdenum (Mo) or zirconium (Zr) in order to stabilize its high-temperature body-centered cubic phase for use in nuclear reactors. However, in all metallic fuel forms, the α phase of U remains in some fraction. This phase decomposition due to temperature or compositional variance can play an outsized role on fuel performance and microstructural evolution. Relatively little is known about fundamental point defect properties in α -U at non-zero temperatures, from either computational or experimental studies. This work performs the first thorough evaluation of the α phase of U via ab initio molecular dynamics (AIMD). A number of thermophysical properties are calculated as a function of temperature, including equilibrium lattice parameters, thermal expansion, and heat capacity. These results indicate a two-region behavior, with the transition at 400 K. The thermal expansion/contraction in the a / b direction occurs rapidly from 100 up to 400 K, after which a more linear and gradual change in the lattice constant takes place. The volumetric expansion matches experiments quantitatively, but the individual lattice constant expansion only matches experiments qualitatively. Point defect formation energies and induced lattice strains are also determined as a function of temperature, providing insight on defect populations and the fundamentals of irradiation growth in α -U. Interstitials induce significantly more strain than vacancies, and the nature of that strain is highly dependent on the individual lattice directions. The direction of point defect-induced lattice strain is contrary to the irradiation growth behavior of α -U. This work shows that isolated point defects cannot be the primary driving force responsible for the significant irradiation-induced growth of α -U observed experimentally.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient Phase-Driven Cyclic Deformation in Additively Manufactured 15-5 PH Steel

The present work extends the examination of selective laser melting (SLM)-fabricated 15-5 PH steel with the 8%-transient-austenite-phase towards fully-reversed strain-controlled low-cycle fatigue (LCF) test. The cyclic-deformation response and microstructural evolution were investigated via in-situ neutron-diffraction measurements. The transient-austenite-phase rapidly transformed into the martensite phase in the initial cyclic-hardening stage, followed by an almost complete martensitic transformation in the cyclic-softening and steady stage. The compressive stress was much greater than the tensile stress at the same strain amplitude. The enhanced martensitic transformation associated with lower dislocation densities under compression predominantly governed such a striking tension-compression asymmetry in the SLM-built 15-5 PH.

15-5 PH stainless steel↗

A Brief Review of the Impact of Neutron Irradiation Damage in Tungsten and Its Alloys

Neutron irradiation poses a substantial challenge in the development and application of tungsten (W) and its alloys, predominantly in the framework of nuclear fusion and fission environments. Although W is well-acknowledged for its unique properties like its high melting temperature and higher resistance to sputtering, transmutation products, such as Re and Os, form and impact the alloy properties as a result of neutron irradiation. This transmutation effect accompanied by significant microstructure damage due to neutron irradiation can lead to the significant degradation of mechanical properties. This review surveys the literature focusing on the microstructural modifications post-irradiation and its impacts on the irradiation hardening. This review provides insights into the elaborative understanding on the neutron radiation damage on W and W alloys by exploring the microstructural evolution and hardness changes post-irradiation. The gaps and future opportunities for understanding neutron radiation damage in W are briefly summarized.

36 MATERIALS SCIENCE↗

High Resolution Mapping of Orientation and Strain Gradients in Metals by Synchrotron 3D X-ray Laue Microdiffraction

Synchrotron 3D X-ray Laue microdiffraction, available at beamline 34-ID-E at Advanced Photon Source in Argonne National Laboratory, is a powerful tool for 3D non-destructive mapping of local orientations and strains at sub-micron scale in the bulk. With this technique, it is possible to study local residual stresses developed during manufacturing or while in service due to interactions between, for example, different phases and/or grains with different orientations in materials containing multiple or single phase(s). Such information is essential for understanding mechanical properties and designing advanced materials, but is largely non-existent in the current generation of materials models. In the present paper, the principle and experimental set-up of the 3D microdiffraction are introduced, followed by a description of a method for quantification of the local plastic deformation based on high-angular-resolution orientation maps. The quantification of local residual stresses in two model materials, ductile cast iron (two phases) and partially recrystallized pure nickel (single phase), using 3D microdiffraction will then be presented. The results show that 3D microdiffraction is important for understanding the origin of local residual stresses and to relate them to the microstructural evolution. Finally, the limitations of the 3D microdiffraction on the current generation synchrotron source and new possibilities after the synchrotron upgrade are discussed.

36 MATERIALS SCIENCE↗

Transmission electron microscopy of ion irradiated ODS MA956 samples

Oxide dispersion strengthened (ODS) alloys are promising candidate materials for the next generation advanced nuclear reactors due to their superior irradiation resistance and mechanical properties. To better understand the effect of irradiation on MA956, it is essential to study higher dose (50-100 dpa) samples, so that the general trend of microstructural evolution and the resulting radiation-hardening can be deduced. Currently, ion irradiations are considered the only way to achieve doses beyond ~50 dpa in a practical time frame relevant to alloy and welding development programs. This dataset contains TEM characterization results of ODS MA956 samples that were ion irradiated under different conditions: Sample #5 (1.25 dpa at 190℃); Sample #9 (50 dpa at 190℃); Sample #15 (1.25dpa under 320℃); and Sample 17 (25 dpa at 320℃). TEM characterization focused on the irradiation induced defects (dislocation lines and loops) using the on-zone axis bright field STEM technique. These data were collected using a FEI Tecnai G2 F30 S/TEM at Microscopy and Characterization Suite (MaCS) at Center for Advanced Energy Studies (CAES), Idaho Falls, ID. This project (ion irradiation and TEM studies) was supported by the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07-05ID14517 as part of Nuclear Science User Facilities award #18-14784 (PI: Ramprashad Prabhakaran, PNNL).

Prabhakaran, Ramprashad↗

Transmission electron microscopy of ion irradiated ODS MA956 samples

Oxide dispersion strengthened (ODS) alloys are promising candidate materials for the next generation advanced nuclear reactors due to their superior irradiation resistance and mechanical properties. To better understand the effect of irradiation on MA956, it is essential to study higher dose (50-100 dpa) samples, so that the general trend of microstructural evolution and the resulting radiation-hardening can be deduced. Currently, ion irradiations are considered the only way to achieve doses beyond ~50 dpa in a practical time frame relevant to alloy and welding development programs. This dataset contains TEM characterization results of ODS MA956 samples that were ion irradiated under different conditions: Sample #5 (1.25 dpa at 190℃); Sample #9 (50 dpa at 190℃); Sample #15 (1.25dpa under 320℃); and Sample 17 (25 dpa at 320℃). TEM characterization focused on the irradiation induced defects (dislocation lines and loops) using the on-zone axis bright field STEM technique. These data were collected using a FEI Tecnai G2 F30 S/TEM at Microscopy and Characterization Suite (MaCS) at Center for Advanced Energy Studies (CAES), Idaho Falls, ID. This project (ion irradiation and TEM studies) was supported by the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07-05ID14517 as part of Nuclear Science User Facilities award #18-14784 (PI: Ramprashad Prabhakaran, PNNL).

Prabhakaran, Ramprashad↗

In situ TEM straining of nanograined free-standing thin films reveals various unexpected deformation mechanisms.

In-situ transmission electron microscopy (TEM) straining experiments provide direct detailed observation of the deformation and failure mechanisms active at a length scale relevant to nanomaterials. This presentation will detail continued investigations into the active mechanisms governing high purity nanograined pulsed-laser deposited (PLD) nickel, as well as recent work into dislocation-particle interactions in nanostructured PLD aluminum-alumina alloys. Straining experiments performed on nanograined PLD free-standing nanograined Ni films with an engineered grain size distribution revealed that the addition of ductility with limited decrease in strength, reported in such metals, can be attributed to the simultaneous activity of three deformation mechanisms in front of the crack tip. At the crack tip, a grain agglomeration mechanism occurs where several nanograins appear to rotate, resulting in a very thin, larger grain immediately prior to failure. In the classical plastic zone in front of the crack tip, a multitude of mechanisms were found to operate in the larger grains including: dislocation pile-up, twinning, and stress-assisted grain growth. The region outside of the plastic zone showed signs of elasticity with limited indications of dislocation activity. The insight gained from in-situ TEM straining experiments of nanograined PLD Ni provides feedback for models of the deformation and failure in nanograined FCC metals, and suggests a greater complexity in the active mechanisms. The investigation into the deformation and failure mechanisms of FCC metals via in-situ TEM straining experiments has been expanded to the effect of hard particles on the active mechanisms in nanograined aluminum with alumina particles. The microstructures investigated were developed with varying composition, grain size, and particle distribution via tailoring of the PLD conditions and subsequent annealing. In order to develop microstructures suitable for in-situ deformation testing, in-situ TEM annealing experiments were performed, revealing the effect of nanoparticle precipitates on grain growth. These films were then strained in the TEM and the resulting microstructural evolution will be discussed. In-situ TEM straining experiments currently provide a wealth of information into plasticity within nanomaterials and can potentially, with further development of TEM and nanofabrication tools, provide even greater investigative capabilities.

36 MATERIALS SCIENCE↗

2D and 3D X-Ray Structural Microscopy Using Submicron-Resolution Laue Microdiffraction

We have developed a scanning, polychromatic x-ray microscopy technique with submicron spatial resolution at the Advanced Photon Source. In this technique, white undulator radiation is focused to submicron diameter using elliptical mirrors. Laue diffraction patterns scattered from the sample are collected with an area detector and then analyzed to obtain the local crystal structure, lattice orientation, and strain tensor. These new microdiffraction capabilities have enabled both 2D and 3D structural studies of materials on mesoscopic length-scales of tenths-to-hundreds of microns. For thin samples such as deposited films, 2D structural maps are obtained by step-scanning the area of interest. For example, 2D x-ray microscopy has been applied in studies of the epitaxial growth of oxide films. For bulk samples, a 3D differential-aperture x-ray microscopy technique has been developed that yields the full diffraction information from each submicron volume element. The capabilities of 3D x-ray microscopy are demonstrated here with measurements of grain orientations and grain boundary motion in polycrystalline aluminum during 3D thermal grain growth. X-ray microscopy provides the needed, direct link between the experimentally measured 3D microstructural evolution and the results of theory and modeling of materials processes on mesoscopic length scales.

36 MATERIALS SCIENCE↗

Interfacial structure in Telluride-based thermoelectric materials.

Chalcogenide compounds based on the rocksalt and tetradymite structures possess good thermoelectric properties and are widely used in a variety of thermoelectric devices. Examples include PbTe and AgSbTe2, which have the rocksalt structure, and Bi2Te3, Bi2Se3, and Sb2Te3, which fall within the broad tetradymite-class of structures. These materials are also of interest for thermoelectric nanocomposites, where the aim is to improve thermoelectric energy conversion efficiency by harnessing interfacial scattering processes (e.g., reducing the thermal conductivity by phonon scattering or enhancing the Seebeck coefficient by energy filtering). Understanding the phase stability and microstructural evolution within such materials is key to designing processing approaches for optimal thermoelectric performance and to predicting the long-term nanostructural stability of the materials. In this presentation, we discuss our work investigating relationships between interfacial structure and formation mechanisms in several telluride-based thermoelectric materials. We begin with a discussion of interfacial coherency and its special aspects at interfaces in telluride compounds based on the rocksalt and tetradymite structures. We compare perfectly coherent interfaces, such as the Bi2Te3 (0001) twin, with semi-coherent, misfitting interfaces. We next discuss the formal crystallographic analysis of interfacial defects in these systems and then apply this methodology to high resolution transmission electron microscopy (HRTEM) observations of interfaces in the AgSbTe2/Sb2Te3 and PbTe/Sb2Te3 systems, focusing on interfaces vicinal to {l_brace}111{r_brace}/{l_brace}0001{r_brace}. Through this analysis, we identify a defect that can accomplish the rocksalt-to-tetradymite phase transformation through diffusive-glide motion along the interface.

36 MATERIALS SCIENCE↗

Migration Mechanisms of Oxygen Interstitial Clusters in UO2

Understanding the migration kinetics of radiation-induced point defects and defect clusters is a key to predicting the microstructural evolution and mass transport in nuclear fuels. Although the diffusion kinetics of point defects in UO2 is well explored both experimentally and theoretically, the kinetics of defect clusters is not well understood. In this work the migration mechanisms of oxygen interstitial clusters of size one to five atoms (1Oi – 5Oi) in UO2 are investigated by temperature-accelerated dynamics simulations without any a priori assumptions of migration mechanisms. It is found that the migration paths of oxygen interstitial clusters are complex and non-intuitive and that multiple migration paths and barriers exist for some clusters. It is also found that the cluster migration barrier does not increase with increasing cluster size and its magnitude has the following order: 2Oi < 3Oi < 1Oi < 5Oi < 4Oi. Possible finite-size effects are checked with three different sized systems. The results show good agreement with other available experimental and theoretical data. In particular, the relatively large migration barriers of cuboctahedral clusters (4Oi and 5Oi) are in good agreement with the experimentally measured oxygen diffusion activation energy in U4O9, which is thought to contain many such clusters. The cluster migration sequence may explain the interesting relationship between the oxygen diffusivity and stoichiometry in UO2+x.

36 MATERIALS SCIENCE↗

Evaluation of irradiation facility options for fusion materials research and development

Successful development of fusion energy will require the design of high-performance structural materials that exhibit dimensional stability and good resistance to fusion neutron degradation of mechanical and physical properties. The high levels of gaseous (H, He) transmutation products associated with deuterium-tritium (D-T) fusion neutron transmutation reactions, along with displacement damage dose requirements up to 50-200 displacements per atom (dpa) for a fusion demonstration reactor (DEMO), pose an extraordinary challenge. The intense neutron source(s) is needed to address two complimentary missions: 1) Scientific investigations of radiation degradation phenomena and microstructural evolution under fusion-relevant irradiation conditions (to provide the foundation for designing improved radiation resistant materials), and 2) Engineering database development for design and licensing of next-step fusion energy machines such as a fusion DEMO. A wide variety of irradiation facilities have been proposed to investigate materials science phenomena and to test and qualify materials for a DEMO reactor. Currently available and proposed facilities include fission reactors (including isotopic and spectral tailoring techniques to modify the rate of H and He production per dpa), dual- and triple-ion accelerator irradiation facilities that enable greatly accelerated irradiation studies with fusion-relevant H and He production rates per dpa within microscopic volumes, D-Li stripping reaction and spallation neutron sources, and plasma-based sources. The advantages and limitations of the main proposed fusion materials irradiation facility options are reviewed. Evaluation parameters include irradiation volume, potential for performing accelerated irradiation studies, capital and operating costs, similarity of neutron irradiation spectrum to fusion reactor conditions, temperature and irradiation flux stability/control, ability to perform multiple-effect tests (e.g., irradiation in the presence of a flowing coolant, or in the presence of complex applied stress fields), and technical maturity/risk of the concept. Ultimately, it is anticipated that heavy utilization of ion beam and fission neutron irradiation facilities along with sophisticated materials models, in addition to a dedicated fusion-relevant neutron irradiation facility, will be necessary to provide a comprehensive and cost-effective understanding of anticipated materials evolution in a fusion DEMO and to therefore provide a timely and robust materials database.

embrittlement↗

FIRST-PRINCIPLES CALCULATIONS OF INTRINSIC DEFECTS AND Mg TRANSMUTANTS IN 3C-SiC

Silicon carbide (SiC) possesses many desirable attributes for applications in high-temperature and neutron radiation environments. These attributes include excellent dimensional and thermodynamic stability, low activation, high strength, and high thermal conductivity. Therefore, SiC based materials draw broad attention as structural materials for the first wall (FW) and blanket in fusion power plants. Under the severe high-energy neutron environment of D-T fusion systems, SiC suffers significant transmutation resulting in both gaseous and metallic transmutants. Recent calculations by Sawan, et al. [2] predict that at a fast neutron dose of ~100 dpa, there will be about 0.5 at% Mg generated in SiC through nuclear transmutation. Other transmutation products, including 0.15 at% Al, 0.2 at% Be and 2.2 at% He, also emerge. Formation and migration energies of point defects in 3C-SiC have been widely investigated using density functional theory (DFT). However, the properties of defects associated with transmutants are currently not well understood. Fundamental understanding of where the transmutation products go and how they affect microstructure evolution of SiC composites will help to predict property evolution and performance of SiC-based materials in fusion reactors.

Environmental Molecular Sciences Laboratory↗

Fatigue and Creep Crack Propagation behaviour of Alloy 617 in the Annealed and Aged Conditions

The crack propagation behaviour of Alloy 617 was studied under various conditions. Elevated temperature fatigue and creep-fatigue crack growth experiments were conducted at 650 and 800 degrees C under constant stress intensity (triangle K) conditions and triangular or trapezoidal waveforms at various frequencies on as-received, aged, and carburized material. Environmental conditions included both laboratory air and characteristic VHTR impure helium. As-received Alloy 617 displayed an increase in the crack growth rate (da/dN) as the frequency was decreased in air which indicated a time-dependent contribution component in fatigue crack propagation. Material aged at 650°C did not display any influence on the fatigue crack growth rates nor the increasing trend of crack growth rate with decreasing frequency even though significant microstructural evolution, including y’ (Ni3Al) after short times, occurred during aging. In contrast, carburized Alloy 617 showed an increase in crack growth rates at all frequencies tested compared to the material in the standard annealed condition. Crack growth studies under quasi-constant K (i.e. creep) conditions were also completed at 650 degrees C and a stress intensity of K = 40 MPa9 (square root)m. The results indicate that crack growth is primarily intergranular and increased creep crack growth rates exist in the impure helium environment when compared to the results in laboratory air. Furthermore, the propagation rates (da/dt) continually increased for the duration of the creep crack growth either due to material aging or evolution of a crack tip creep zone. Finally, fatigue crack propagation tests at 800 degrees C on annealed Alloy 617 indicated that crack propagation rates were higher in air than impure helium at the largest frequencies and lowest stress intensities. The rates in helium, however, eventually surpass the rates in air as the frequency is reduced and the stress intensity is decreased which was not observed at 650 degrees C.

36 MATERIALS SCIENCE↗

Stability of SiC-Matrix Microencapsulated Fuel Constituents at Relevant LWR Conditions

This paper addresses certain key feasibility issues facing the application of SiC-matrix microencapsulated fuels for light water reactor application. Issues addressed are the irradiation stability of the SiC-based nano-powder ceramic matrix under LWR-relevant irradiation conditions, the presence or extent of reaction of the SiC matrix with zirconium-based cladding, the stability of the inner and outer pyrolytic graphite layers of the microencapsulated (TRISO) particle at this uncharacteristically low irradiation temperature, and the state of the particle-matrix interface following irradiation which could possibly effect thermal transport. In the process of determining these feasibility issues microstructural evolution and change in dimension and thermal conductivity was studied. As a general finding the SiC matrix was found to be quite stable with behavior similar to that of CVD SiC. In magnitude the irradiation-induced swelling of the matrix material was slightly higher and irradiation-degraded thermal conductivity was slightly lower as compared to CVD SiC. No significant reaction of this SiC-based nano-powder ceramic matrix material with Zircaloy was observed. Irradiation of the TRISO in the 320-360 C range to a maximum dose of 7.7 1025 n/m2 (E > 0.1 MeV) did not have significant negative impact on the constituent layers of the TRISO fuel. At the highest dose studied layer structure and interface integrity remained essentially unchanged with good apparent thermal transport through the microsphere to the surrounding matrix.

nuclear fuel↗

In-situ Phase transformation study in fine grained heat affected zone of Grade 91 steels

Creep strength-enhanced ferritic (CSEF) steels such as the 9 Cr steel [ASTM A387 Grade 91] are widely used as tubing and piping in the new generation of fossil fired power plants. Microstructures in the fine-grained heat affected zone (FGHAZ) may significantly reduce creep strength leading Type IV failures. Current research suggest that reducing pre-weld tempering temperature from 760 C (HTT) to 650 C (LTT) has the potential to double the creep life of these welds. To understand this improvement, time-resolved X-ray diffraction (TRXRD) measurement with synchrotron radiation was used to characterize the microstructure evolution during fine grained heat-affected zone (HAZ) thermal cycling of grade 91 steel. The measurements showed both M23C6 (M=Fe, Cr) and MX (M=Nb, V; X=C,N) are present in the sample after the HTT condition. Near equilibrium fraction of M23C6 was measured in high temperature tempering condition (HTT, 760 C). However, the amount of M23C6 in LTT condition was very low since the diffraction peaks are close to the background. During simulated FGHAZ thermal cycling, the M23C6 partially dissolved in HTT sample. Interestingly, MX did not dissolve in both LTT and HTT samples. Hypothesis for correlation of M23C6 carbide distribution and pre-mature creep failure in FGHAZ will be made.

Babu, Sudarsanam Suresh↗