Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSIBILITY EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Strategies for on-chip digital data compression for X-ray pixel detectors

Here, the continued desire for X-ray pixel detectors with higher frame rates will stress the ability of application-specific integrated circuit (ASIC) designers to provide sufficient off-chip bandwidth to reach continuous frame rates in the 1 MHz regime. To move from the current 10 kHz to the 1 MHz frame rate regime, ASIC designers will continue to pack as many power-hungry high-speed transceivers at the periphery of the ASIC as possible. In this paper, however, we present new strategies to make the most efficient use of the off-chip bandwidth by utilizing data compression schemes for X-ray photon-counting and charge-integrating pixel detectors. In particular, we describe a novel in-pixel compression scheme that converts from analog to digital converter units to encoded photon counts near the photon Poisson noise level and achieves a compression ratio of >1.5x independent of the dataset. In addition, we describe a simple yet efficient zero-suppression compression scheme called "zeromask" (ZM) located at the ASIC's edge before streaming data off the ASIC chip. ZM achieves average compression ratios of >4x, >7x, and >8x for high-energy X-ray diffraction, ptychography, and X-ray photon correlation spectroscopy datasets, respectively. We present the conceptual designs, register-transfer level block diagrams, and the physical ASIC implementation of these compression schemes in 65 nm CMOS. When combined, these two digital compression schemes could increase the effective off-chip bandwidth by a factor of 6-12x.

47 OTHER INSTRUMENTATION↗

Wave transience in a compressible atmosphere. I - Transient internal wave, mean-flow interaction. II - Transient equatorial waves in the quasi-biennial oscillation

Analytical and numerical solutions are obtained in an approximate quasi-linear model, to describe the way in which vertically propagating waves give rise to mean flow accelerations in an atmosphere due to the effects of wave transience. These effects in turn result from compressibility and vertical group velocity feedback, and culminate in the spontaneous formation and descent of regions of strong mean wind shear. The numerical solutions display mean flow accelerations due to Kelvin waves in the equatorial stratosphere, with wave absorption altering the transience mechanism in such significant respects as causing the upper atmospheric mean flow acceleration to be very sensitive to the precise magnitude and distribution of the damping mechanisms. The numerical simulations of transient equatorial waves in the quasi-biennial oscillation are also considered.

Dunkerton, T. J.↗

Effect of grain-boundary θ-Al 2 Cu precipitates on tensile and compressive creep properties of cast Al–Cu–Mn–Zr alloys

Tensile and compressive creep tests were performed at 300 °C on high-temperature Al–Cu–Mn–Zr (ACMZ) alloys with 6 wt% Cu (6Cu) and 9 wt% Cu (9Cu) to evaluate the effect on creep properties of micron-size θ-Al 2 Cu intergranular precipitates. For compressive creep, the increased volume fraction of θ-precipitates at grain boundaries (from ~0.7% in 6Cu to ~ 6% in 9Cu) does not affect deformation rates across the investigated stress range of 15–110 MPa, consistent with creep being controlled by submicron θ'-Al 2 Cu precipitates within grains, whose size and fractions are the same in both alloys. In contrast, for tensile creep, 9Cu creeps faster than 6Cu at stresses above 20 MPa, and this difference increases with the stress level. Additionally, this discrepancy between tensile and compressive creep behavior is explained by cavitation during tensile creep, which is favored by higher volume fraction and larger size of intergranular θ precipitates in 9Cu. Conversely, larger precipitates impede cavity linkage resulting in improved creep ductility of 9Cu as compared to 6Cu at 300 °C.

36 MATERIALS SCIENCE↗

Three-dimensional multigrid Navier-Stokes computations for turbomachinery applications

The fully three-dimensional, time-dependent compressible Navier-Stokes equations in cylindrical coordinates are presently used, in conjunction with the multistage Runge-Kutta numerical integration scheme for solution of the governing flow equations, to simulate complex flowfields within turbomechanical components whose pertinent effects encompass those of viscosity, compressibility, blade rotation, and tip clearance. Computed results are presented for selected cascades, emphasizing the code's capabilities in the accurate prediction of such features as airfoil loadings, exit flow angles, shocks, and secondary flows. Computations for several test cases have been performed on a Cray-YMP, using nearly 90,000 grid points.

Subramanian, S. V.↗

Optimizing supercapacitor electrode density: achieving the energy of organic electrolytes with the power of aqueous electrolytes

The value of electrode density is often overlooked in the pursuit of impressive supercapacitor metrics. Low-density electrodes deliver the best performance in terms of gravimetric energy and power densities when only the mass of the electrodes is considered. However, energy and power values with respect to the total system mass (electrode + electrolyte) or volume are more meaningful for practical application. Low-density electrodes are impractical due to both large mass contributions by the electrolyte and large system volumes. In this work, we use highly compressible graphene aerogel electrodes (up to 87.5% volumetric compression) to systematically characterize the effects of electrode density on energy and power metrics. The results reveal that electrode density is similar to electrode thickness in that both parameters have a squared effect on power. Accounting for the aqueous electrolyte's mass lowered the gravimetric energy and power by almost an order of magnitude for 0.144 g cm –3 dense carbon electrodes but only by a factor of 1.5 when the electrode density was increased to 1.15 g cm –3 through compression. The high-density electrodes achieve 8 W h kg –1 , 70 000 W kg –1 , and 144 F cm –3 in a symmetric electrode setup after factoring in the aqueous electrolyte's mass. Therefore, in the pursuit of high energy per mass, it can be just as effective to lower the system's mass with smaller electrolyte fractions as it is to use electrolytes with larger voltage ranges. High electrode densities allow aqueous electrolyte supercapacitors to attain energy densities per the system mass comparable to those of commercially-available organic electrolyte supercapacitors while maintaining 10–100× greater power.

25 ENERGY STORAGE↗

Iterative spectral methods and spectral solutions to compressible flows

A spectral multigrid scheme is described which can solve pseudospectral discretizations of self-adjoint elliptic problems in O(N log N) operations. An iterative technique for efficiently implementing semi-implicit time-stepping for pseudospectral discretizations of Navier-Stokes equations is discussed. This approach can handle variable coefficient terms in an effective manner. Pseudospectral solutions of compressible flow problems are presented. These include one dimensional problems and two dimensional Euler solutions. Results are given both for shock-capturing approaches and for shock-fitting ones.

Hussaini, M. Y.↗

End-to-end quality measure for transmission of compressed imagery over a noisy coded channel

For the transmission of imagery at high data rates over large distances with limited power and system gain, it is usually necessary to compress the data before transmitting it over a noisy channel that uses channel coding to reduce the effect of noise introduced errors. Both compression and channel noise introduce distortion into the imagery. In order to design a communication link that provides adequate quality of received images, it is necessary first to define some suitable distortion measure that accounts for both these kinds of distortion and then to perform various tradeoffs to arrive at system parameter values that will provide a sufficiently low level of received image distortion. The overall mean square error is used as the distortion measure and a description of how to perform these tradeoffs are included.

Korwar, V. N.↗

Electrolyte Assisted Hydrogen Storage Reactions (Final Technical Report)

The goal of this project is to address critical deficiencies of hydrogen storage systems design based on hydride materials, as originally identified by the DOE Hydrogen Storage Engineering Center of Excellence (HSECoE). Baseline hydrogen storage technology presently relies on compressed gas operating at ~700 bar pressure, which imposes huge demands on fuel delivery, fuel storage and system cost. For onboard storage applications, Type IV composite overwrapped pressure vessels and associated balance-of-plant components are necessary to ensure safe and effective fuel delivery. However, such compressed gas technology falls well-short of volumetric targets even at 700 bar, given the density of gaseous molecular hydrogen is only 40 g·H2/l at ambient temperatures. One alternative is to utilize hydride materials which accommodate hydrogen in atomic form. Certain hydrides can attain volumetric densities that exceed the density of liquid H2 (71 g·H2/l) while also offering advantageous thermodynamic properties. However, such material systems presently rely on solid-state diffusion for hydrogen release, which has a very high activation barrier for atom mobility and, thus, requires impractically-high temperatures for operation. The initial focus of our research effort is to employ and demonstrate an electrolyte system to mediate the diffusion of species at lower temperatures relevant to transportation applications, with the goal of establishing the critical factors necessary to obviate the need for high-temperature release of hydrogen. A parallel goal of this exploratory effort is to determine the effectiveness of modest electrochemical potentials in overcoming any endothermic requirements for hydrogen release in a similar electrolyte-promoted scenario.

08 HYDROGEN↗

Numerical Investigation of a Gasoline-Like Fuel in a Heavy-Duty Compression Ignition Engine Using Global Sensitivity Analysis

Fuels in the gasoline auto-ignition range (Research Octane Number (RON) > 60) have been demonstrated to be effective alternatives to diesel fuel in compression ignition engines. Such fuels allow more time for mixing with oxygen before combustion starts, owing to longer ignition delay. Moreover, by controlling fuel injection timing, it can be ensured that the in-cylinder mixture is “premixed enough” before combustion occurs to prevent soot formation while remaining “sufficiently inhomogeneous” in order to avoid excessive heat release rates. Gasoline compression ignition (GCI) has the potential to offer diesel-like efficiency at a lower cost and can be achieved with fuels such as low-octane straight run gasoline which require significantly less processing in the refinery compared to today’s fuels. To aid the design and optimization of a compression ignition (CI) combustion system using such fuels, a global sensitivity analysis (GSA) was conducted to understand the relative influence of various design parameters on efficiency, emissions and heat release rate. The design parameters included injection strategies, exhaust gas recirculation (EGR) fraction, temperature and pressure at intake valve closure and injector configuration. These were varied simultaneously to achieve various targets of ignition timing, combustion phasing, overall burn duration, emissions, fuel consumption, peak cylinder pressure and maximum pressure rise rate. The baseline case was a three-dimensional closed-cycle computational fluid dynamics (CFD) simulation with a sector mesh at medium load conditions. Eleven design parameters were considered and ranges of variation were prescribed to each of these. These input variables were perturbed in their respective ranges using the Monte Carlo (MC) method to generate a set of 256 CFD simulations and the targets were calculated from the simulation results. GSA was then applied as a screening tool to identify the input parameters having the most significant impact on each target. The results were further assessed by investigating the impact of individual parameter variations on the targets. Overall, it was demonstrated that GSA can be an effective tool in understanding parameters sensitive to a low temperature combustion concept with novel fuels.

Pal, Pinaki↗

Pressure-gradient-induced Alfvén eigenmodes: I. Ideal MHD and finite ion Larmor radius effects

In the second magnetohydrodynamic (MHD) ballooning stable domain of a high-beta tokamak plasma, the Schrödinger equation for ideal MHD shear Alfvén waves has discrete solutions corresponding to standing waves trapped between pressure-gradient-induced potential wells. Our goal is to understand how these so-called α-induced toroidal Alfvén eigenmodes (αTAE) are modified by the effects of finite Larmor radii (FLR) and kinetic compression of thermal ions in the limit of massless electrons. In this paper, we neglect kinetic compression in order to isolate and examine in detail the effect of FLR terms. After a review of the physics of ideal MHD αTAE, the effect of FLR on the Schrödinger potential, eigenfunctions and eigenvalues is described with the use of parameter scans. The results are used in a companion paper to identify instabilities driven by wave–particle resonances in the second stable domain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Novel Use of a Pneumatic Compression Device for Haemostasis of Haemodialysis Fistula Access Catheterisation Sites

PurposeTransradial pneumatic compression devices can be used to achieve haemostasis following radial artery puncture. This article describes a novel technique for acquiring haemostasis of arterio-venous haemodialysis fistula access sites without the need for suture placement using one such compression device.Materials and MethodsA retrospective review of fistulograms with or without angioplasty/thrombectomy in a single institution was performed. 20 procedures performed on 12 patients who underwent percutaneous intervention of failing or thrombosed arterio-venous fistulas (AVF) had 27 puncture sites. Haemostasis was achieved using a pneumatic compression device at all access sites. Procedure details including size of access sheath, heparin administration and complications were recorded.ResultsTwo diagnostic fistulograms, 14 fistulograms and angioplasties and four thrombectomies were performed via access sheaths with an average size (±SD) of 6 Fr (±1.12). IV unfractionated heparin was administered in 11 of 20 procedures. Haemostasis was achieved in 26 of 27 access sites following 15–20 min of compression using the pneumatic compression device. One case experienced limited bleeding from an inflow access site that was successfully treated with reinflation of the device for a further 5 min. No other complication was recorded.ConclusionsHaemostasis of arterio-venous haemodialysis fistula access sites can be safely and effectively achieved using a pneumatic compression device. This is a technically simple, safe and sutureless technique for acquiring haemostasis after AVF intervention.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Dynamics of Longitudinal Phase-Space Modulations in an rf Compressor for Electron Beams

Free Electron Lasers (FELs) operating in the UV or x-ray radiation spectrum require peak beam currents that are generally higher than those obtainable by present electron sources, thus making bunch compression necessary. Compression, however, may heighten the effects of collective forces and degrade the beam quality. In this paper they provide a framework for investigating some of these effects in rf compressors by focusing on the longitudinal dynamics of small-amplitude density perturbations, which have the potential to cause the disruptive appearance of the so-called microbunching instability. They develop a linear theory valid for low-to-moderate compression factors under the assumption of a 1D impedance model of longitudinal space charge and provide validation against macroparticle simulations.

43 PARTICLE ACCELERATORS↗

Growth and Morphology of Supercritical Fluids, a Fluid Physics Experiment Conducted on Mir, Complete

The Growth and Morphology of Supercritical Fluids (GMSF) is an international experiment facilitated by the NASA Glenn Research Center and under the guidance of U.S. principal investor Professor Hegseth of the University of New Orleans and three French coinvestigators: Daniel Beysens, Yves Garrabos, and Carole Chabot. The GMSF experiments were concluded in early 1999 on the Russian space station Mir. The experiments spanned the three science themes of near-critical phase separation rates, interface dynamics in near-critical boiling, and measurement of the spectrum of density fluctuation length scales very close to the critical point. The fluids used were pure CO2 or SF6. Three of the five thermostats used could adjust the sample volume with the scheduled crew time. Such a volume adjustment enabled variable sample densities around the critical density as well as pressure steps (as distinct from the usual temperature steps) applied to the sample. The French-built ALICE II facility was used for these experiments. It allows tightly thermostated (left photograph) samples (right photograph) to be controlled and viewed/measured. Its diagnostics include interferometry, shadowgraph, high-speed pressure measurements, and microscopy. Data were logged on DAT tapes, and PCMCIA cards and were returned to Earth only after the mission was over. The ground-breaking near critical boiling experiment has yielded the most results with a paper published in Physical Review Letters (ref. 1). The boiling work also received press in Science Magazine (ref. 2). This work showed that, in very compressible near-critical two-phase pure fluids, a vapor bubble was induced to temporarily overheat during a rapid heating of the sample wall. The temperature rise in the vapor was 23-percent higher than the rise in the driving container wall. The effect is due to adiabatic compression of the vapor bubble by the rapid expansion of fluid near the boundary during heatup. Thermal diffusivity is low near the critical point, so getting heat out of the compressed bubble is observably slow. This gives the appearance of a backward heat flow, or heat flow from a cold surface to a warm fluid.

Wilkinson, R. Allen↗

Piezoresistance and solar cell efficiency

Diffusion-induced stresses in silicon are shown to result in large localized changes in the minority-carrier mobility which in turn can have a significant effect on cell output. Evidence is given that both compressive and tensile stresses can be generated in either the emitter or the base region. Tensile stresses in the base appear to be much more effective in altering cell performance than do compressive stresses. While most stress-related effects appear to degrade cell efficiency, this is not always the case. Evidence is presented showing that arsenic-induced stresses can result in emitter characteristics comparable to those found in the MINP cell without requiring a high degree of surface passivation.

Weizer, Victor G.↗

Piezothermal effect in a spinning gas

A spinning gas, heated adiabatically through axial compression, is known to exhibit a rotation-dependent heat capacity. However, as equilibrium is approached, an effect is identified here wherein the temperature does not grow homogeneously in the radial direction, but develops a temperature differential with the hottest region on axis, at the maximum of the centrifugal potential energy. This phenomenon, which we call a piezothermal effect , is shown to grow bilinearly with the compression rate and the amplitude of the potential. As a result, numerical simulations confirm a simple model of this effect, which can be generalized to other forms of potential energy and methods of heating.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Martensitic fcc-hcp transformation pathway in solid krypton and xenon and its effect on their equations of state

The martensitic transformation is a fundamental physical phenomenon at the origin of important industrial applications. However, the underlying microscopic mechanism, which is of critical importance to explain the outstanding mechanical properties of martensitic materials, is still not fully understood. This is because for most martensitic materials the transformation is a fast process that makes in situ studies extremely challenging. Noble solids krypton and xenon undergo a progressive pressure-induced face-centered cubic (fcc) to hexagonal close-packed (hcp) martensitic transition with a very wide coexistence domain. Here, we took advantage of this unique feature to study the detailed transformation progress at the atomic level by employing in situ x-ray diffraction and absorption spectroscopy. We evidenced a four-stage pathway and suggest that the lattice mismatch between the fcc and hcp forms plays a key role in the generation of strain. We also determined precisely the effect of the transformation on the compression behavior of these materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Finite Element Modeling for Compression Strength Prediction of Honeycomb Cores with Geometric Imperfections Measured using X-ray CT Imaging

Aluminum honeycomb cores have been used extensively in composite sandwich panels due to having high bending rigidity while maintaining low density. During manufacturing of the aluminum honeycomb, the thin metal walls are susceptible to imperfections that deviate from an ideal honeycomb shape. Computational tools to quantify imperfections and investigate their effects on quasi-static compression and impact response can inform design criteria to construct safer and lighter launch vehicle structures. This paper presents the results of a study on finite element modeling of metallic honeycomb cores (HCC) with geometric imperfections measured using X-ray Computer Tomography (CT), to predict the compression response. Finite element (FE) models are constructed with measured imperfections with appropriate boundary conditions. It is shown that the average behavior of larger 10x11 cell models can be predicted by sampling single cell models from the larger domain. Amplification of imperfections for cells at the center of sampled specimens are mode switched from the larger out-of-plane imperfection to the mode shape of the adjacent cells resulting in strengthening of the center specimens.

aluminum honeycomb↗