Search NASA⌕ Search

SEARCH · Search NASA

Results for “Estimation method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Characteristics of infrasound signals from North Korean underground nuclear explosions on 2016 January 6 and September 9

This study investigates infrasound signals from North Korean underground nuclear explosions on 2016 January 6 at 01:30:01 UTC (UNEJ16) and on 2016 September 9 at 00:30:01 UTC (UNES16). Infrasound observations from eight, seismo-acoustic arrays at distances of 300–600 km from the explosions and aligned approximately east–west across South Korea are used in the analysis. Progressive multichannel correlation was used followed by analyst review to identify the infrasound arrivals with estimates of azimuth, phase velocity, celerity, F-statistic, signal-to-noise ratio, correlation and signal duration. These observations are compared with model predictions of travel path, ray turning height and relative amplitudes, using Ground-to-Space atmospheric specifications at the time of each explosion. Stratospheric conditions at the time of the UNEJ16 are favourable to the Korean arrays when all arrays detected infrasound signals, while the few detections for UNES16 are consistent with unfavourable stratospheric winds and reduced amplitude thermospheric arrivals. Infrasound locations of the explosions were estimated using the Bayesian Infrasonic Source Location method (BISL), with wind-corrected backazimuth estimates based on the ray tracing calculations. Adding wind corrections to BISL resulted in infrasound locations up to 50 per cent closer to the seismic epicentre over uncorrected locations. The UNES16 infrasound location estimate using atmospheric corrections had larger differences (~67 km difference from seismic location) than the UNEJ16 location (~11 km difference from seismic location) as a result of the reduced number of observations and poor azimuth coverage for UNES16. Based on stratospheric phases recorded at six arrays and the empirical yield-scaling relations, wind corrected amplitudes from UNEJ16 lead to equivalent infrasound source energy estimates between 0.9 and 16.1 tons of TNT detonated in the atmosphere with an average of 6.4 tons and a standard deviation of 4.6 tons.

58 GEOSCIENCES↗
DOE OSTI2020

New Yield Estimates for Nuclear Detonations Over Water

One of the primary methods used by the United States to estimate the yields of atmospheric nuclear tests performed in the 1940’s, 50’s, and 60’s was to film each detonation with a high-speed camera, measure the blast radius as a function of time, and then use Taylor’s spherical blast wave equation to calculate the source energy (i.e., the yield). For surface detonations, the yield in Taylor’s equation was assumed to be twice as large as the actual yield to account for the energy reflected from the surface, assuming the ground was a perfect reflector. Recent simulations of surface detonations over water (referred to as barge shots) have shown that Taylor’s equation must be modified further to account for material entrainment and heat losses. We have computed this lost energy using a high-order radiation-hydrodynamics code to determine the reduction in blast radius vs. time. By analyzing simulation data in the same manner as film data, we have determined that a yield correction factor of 1.27± 0.04 should be applied to the barge shots.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Adaptive Framework for Maintenance Scheduling Based on Dynamic Preventive Intervals and Remaining Useful Life Estimation

Data-based prognostic methods exploit sensor data to forecast the remaining useful life (RUL) of industrial settings to optimize the scheduling of maintenance actions. However, implementing sensors may not be cost-effective or practical for all components. Traditional preventive approaches are not based on sensor data; however, they schedule maintenance at equally spaced intervals, which is not a cost-effective approach since the distribution of the time between failures changes with the degradation state of other parts or changes in working conditions. This study introduces a novel framework comprising two maintenance scheduling strategies. In the absence of sensor data, we propose a novel dynamic preventive policy that adjusts intervention intervals based on the most recent failure data. When sensor data are available, a method for RUL prediction, designated k-LSTM-GFT, is enhanced to dynamically account for RUL prediction uncertainty. The results demonstrate that dynamic preventive maintenance can yield cost reductions of up to 51.8% compared to conventional approaches. The predictive approach optimizes the exploitation of RUL, achieving costs that are only 3–5% higher than the minimum cost achievable while ensuring the safety of critical systems since all of the failures are avoided.

Nunes, Pedro (ORCID:0000000180012172)↗
DOE OSTI2015

ANALYSIS OF EPR AND FISH STUDIES OF RADIATION DOSES IN PERSONS WHO LIVED IN THE UPPER REACHES OF THE TECHA RIVER

Waterborne radioactive releases into the Techa River from the Mayak Production Association in Russia during 1949–1956 resulted in significant doses to about 30,000 persons who lived in downstream settlements. The residents were exposed to internal and external radiation. Two methods for reconstruction of the external dose are considered in this paper, electron paramagnetic resonance (EPR) measurements of teeth and fluorescence in situ hybridization (FISH) measurements of chromosome translocations in circulating lymphocytes. The main issue in the application of the EPR and FISH methods for reconstruction of the external dose for the Techa Riverside residents was strontium radioisotopes incorporated in teeth and bones that served as a source of confounding local exposures. In order to estimate and subtract doses from incorporated 89,90Sr, the EPR and FISH assays were supported by measurements of 90Sr-body burdens and estimates of 90Sr concentrations in dental tissues by the luminescence method. The resulting dose estimates derived from EPR and FISH measurements for residents of the upper Techa River were found to be consistent: the mean values vary from 510 – 550 mGy for the villages located close to the site of radioactive release to 130 – 160 mGy for the more distant villages. The upper bound of individual estimates for both methods is equal to 2.2 – 2.3 Gy. The EPR- and FISH-based dose estimates were compared with the doses calculated for the donors using the Techa River Dosimetry System (TRDS). The TRDS external dose assessments were based on the data on contamination of the Techa River floodplain, simulation of ai r kerma above the contaminated soil, age-dependent life-styles and individual residence histories. For correct comparison TRDS-based doses were calculated from two sources: external exposure from the contaminated environment and internal exposure from 137Cs incorporated in donors’ soft tissues. The TRDS-based absorbed doses in tooth enamel and muscle were in agreement with with EPR- and FISH-based estimates within uncertainty bounds. Basically, the agreement between the estimates has confirmed the validity of external doses calculated with the Techa River Dosimetry System.

dose reconstruction↗
DOE OSTI2022

Flow Loop Study of ECT-Based Volume Fraction Monitoring in Oil–Water Two-Phase Flows

Measurement of phase volume fractions in water-containing multiphase flows is necessary for the optimization of a host of industrial flow processes. Many water-containing multiphase flows can be classified as either water-dispersed or water-continuous mixtures. A recently developed approach based on Hanai’s mixture formula and utilizing electrical capacitance tomography (ECT) sensors have shown good potential for obtaining water volume fraction estimates in two-phase water-containing flows with different water salinity levels. However, the proposed approach was investigated via controlled experiments restricted to static configurations while, in practice, multiphase flows can be dynamic and unpredictable. In this work, we perform a flow loop study of the proposed ECT-based method for volume fraction estimation in oil–water two-phase flows. Here, we evaluate the performance of the proposed method in both water-dispersed and water-continuous flow regimes by employing different types of capacitive sensors in cylindrical arrangements and parallel-plate rectangular arrangements.

02 PETROLEUM↗
DOE OSTI2019

Chemical Composition Analysis for X-Ray Transport Container Scans

It is important for national security to control the movement of dangerous or strategically cargo such as explosives, radioactive materials, rare and precious metals. This control can be provided by scanning transport containers by gamma rays. In this report the existing technique for scanning (dual energy method) is considered and the alternative method based on measuring the energy distribution of gamma rays is proposed. For estimation perspectives of the proposing method, the corresponding simulation was conducted by using the GEANT4 toolkit. The example of the algorithm of reconstruction the chemical composition of the scanned object is also considered. In addition the experiment for estimation energy resolution of the detector based on a scintillation crystal BGO and SiPM was carried out.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2019

Evaluation of Plastic “Eta” Factor for Welds of SS316L(N) with High Strength Mismatch Ratio

Fracture testing standards of ASTM and ISO recommend expressions for plastic η factor of various fracture test specimen geometries to evaluate the fracture behavior of materials. These are intended for homogenous specimens, but according to ISO 15653, it can be extended for weldments up to a strength mismatch ratio (M) of 1.25. In practice, M > 1.25 is encountered in many applications. In the present study, η factor has been evaluated for welded compact tension specimens using a limit load-based approach. The η factors obtained using this approach for homogenous specimens with elastic–perfectly plastic material model are found to be within ± 4% of those from the ASTM E 1820-17a, thereby validating the procedure. For welds, the limit load is obtained from nonlinear (elastic–plastic) FE simulations. η factors for specimens with various crack lengths (a), weld width (h) and strength mismatch have been evaluated and found to be significantly influenced by these parameters. For M > 1.25, the estimated η values were found to be ~ 16% lower compared to that from the ASTM E 1820-17a. Thus, the use of the η values from the proposed method provides a conservative estimate of J–R curve for the welds. Further, it has been observed that depending on the slope of the blunting line, the J{sub Ic} value may vary significantly with the estimated η values.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Adaptive Generation of Training Data for ML Reduced Model Creation

Machine learning proxy models are often used to speed up or completely replace complex computational models. The greatly reduced and deterministic computational costs enable new use cases such as digital twin control systems and global optimization. The challenge of building these proxy models is generating the training data. A naive uniform sampling of the input space can result in a non-uniform sampling of the output space of a model. This can cause gaps in the training data coverage that can miss finer scale details resulting in poor accuracy. While larger and larger data sets could eventually fill in these gaps, the computational burden of full-scale simulation codes can make this prohibitive. In this paper, we present an adaptive data generation method that utilizes uncertainty estimation to identify regions where training data should be augmented. By targeting data generation to areas of need, representative data sets can be generated efficiently. The effectiveness of this method will be demonstrated on a simple one-dimensional function and a complex multidimensional physics model.

Cianciosa, Mark↗
DOE OSTI2023

Discrete Measurements of the Least Horizontal Principal Stress from Core Data: An Application of Viscoelastic Stress Relaxation

Summary The emerging Paradox Oil Play in southeastern Utah is among the most significant unconventional plays in the western USA. The mean total undiscovered oil resources within just the Pennsylvanian Cane Creek interval of the Paradox Basin are believed to exceed 215 million barrels. However, to date, less than 5% (~9 million barrels) of the total Cane Creek resource has been produced from fewer than 40 wells, and only approximately one-half of those are horizontal wells. More than 95% of production is from the central Cane Creek Unit (CCU). Natural fractures are a key feature of many production wells, but stimulation by induced hydraulic fractures is not consistently successful. We hypothesize that more effective production in this play will rely on better fundamental characterization, especially on better quantification of the state of stress. Approximately 110 ft of core, well logs, and a diagnostic fracture injection test (DFIT) were acquired from the State 16-2 well within the CCU. With these data, we applied two methods to constrain and clarify the state of stress. The first technique, the Simpson’s coefficient method, provides lower bounds on the two horizontal principal stresses and relies on only limited data. Alternatively, the viscoelastic stress relaxation (VSR) method is used to estimate the least horizontal principal stress, building on observations that principal stresses become more isotropic as the viscous behavior of a rock is more pronounced. Results of these two methods support the hypothesis that the state of stress in the CCU of the Paradox Basin is nearly lithostatic and isotropic. Other factors consistent with this hypothesis include high formation pore pressure, which tends to reduce the possible stress states by changing the frictional failure equilibrium; lack of induced fractures in the core, which should be present in the case of stress anisotropy; and interbedded halite layers, which given their high degree of ductility, probably lead to greater VSR for the entire sedimentary package.

Energy & Fuels↗
DOE OSTI2016

Estimating methane emissions in California's urban and rural regions using multitower observations

Here, we present an analysis of methane (CH 4 ) emissions using atmospheric observations from 36 thirteen sites in California during June 2013 – May 2014. A hierarchical Bayesian inversion 37 method is used to estimate CH 4 emissions for spatial regions (0.3° pixels for major regions) by 38 comparing measured CH 4 mixing ratios with transport model (WRF-STILT) predictions based 39 on seasonally varying California-specific CH 4 prior emission models. The transport model is 40 assessed using a combination of meteorological and carbon monoxide (CO) measurements 41 coupled with the gridded California Air Resources Board (CARB) carbon monoxide (CO) 42 emission inventory. Hierarchical Bayesian inversion suggests that state annual anthropogenic 43 CH 4 emissions are 2.42 ± 0.49 Tg CH 4 /yr (at 95% confidence, including transport bias 44 uncertainty), higher (1.2 - 1.8 times) than the CARB current inventory (1.64 Tg CH 4 /yr in 2013). 45 We note that the estimated CH 4 emissions drop to 1.0 - 1.6 times the CARB inventory if we 46 correct for the 10% median CH 4 emissions assuming the bias in CO analysis is applicable to 47 CH 4 . The CH 4 emissions from the Central Valley and urban regions (San Francisco Bay and 48 South Coast Air Basins) account for ~58% and 26% of the total posterior emissions, 49 respectively. This study suggests that the livestock sector is likely the major contributor to the 50 state total CH 4 emissions, in agreement with CARB’s inventory. Attribution to source sectors for 51 sub-regions of California using additional trace gas species would further improve the 52 quantification of California’s CH 4 emissions and mitigation efforts towards the California Global 53 Warming Solutions Act of 2006 (AB-32).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Electric Power Consumption Coefficients for U.S. Industries: Regional Estimation and Analysis

Economic activity relies on electric power provided by electrical generation, transmission, and distribution systems. This paper presents a method developed at Los Alamos National Laboratory to estimate electric power consumption by different industries in the United States. Results are validated through comparisons with existing literature and benchmarking data sources. We also discuss the limitations and applications of the presented method, such as estimating indirect electric power consumption and assessing the economic impact of power outages based on input-output economic models.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

An iterative bidirectional gradient boosting approach for CVR baseline estimation

Here this paper presents a novel Iterative Bidirectional Gradient Boosting Model (IBi-GBM) for estimating the baseline of Conservation Voltage Reduction (CVR) programs. In contrast to many existing methods, we treat CVR baseline estimation as a missing data retrieval problem. The approach involves dividing the load and its corresponding temperature profiles into three periods: pre-CVR, CVR, and post-CVR. To restore the missing load profile during the CVR period, the method employs a three-step process. First, a forward-pass GBM is executed using data from the pre-CVR period as inputs. Subsequently, a backward-pass GBM is applied using data from the post-CVR period. The two restored load profiles are reconciled, considering pre-calculated weights derived from forecasting accuracy, and only the leftmost and rightmost points are retained. The newly restored points are then included as inputs for the subsequent iteration. This iterative procedure continues until the original load data in the CVR period is fully restored. We develop IBi-GBM using actual smart meter and Supervisory Control and Data Acquisition (SCADA) data. Our results demonstrate that IBi-GBM exhibits robust performance across various data resolutions and in different seasons and outperforms existing methods by achieving a 1-2% reduction in normalized Root Mean Square Error (nRMSE).

42 ENGINEERING↗
DOE OSTI2021

A causal data fusion method for the general exposure and outcome

Abstract With the advent of the big data era, the need to combine multiple individual data sets to draw causal effects arises naturally in many medical and biological applications. Especially each data set cannot measure enough confounders to infer the causal effect of an exposure on an outcome. In this article, we extend the method proposed by a previous study to causal data fusion of more than two data sets without external validation and to a more general (continuous or discrete) exposure and outcome. Theoretically, we obtain the condition for identifiability of exposure effects using multiple individual data sources for the continuous or discrete exposure and outcome. The simulation results show that our proposed causal data fusion method has unbiased causal effect estimate and higher precision than traditional regression, meta‐analysis and statistical matching methods. We further apply our method to study the causal effect of BMI on glucose level in individuals with diabetes by combining two data sets. Our method is essential for causal data fusion and provides important insights into the ongoing discourse on the empirical analysis of merging multiple individual data sources.

Li, Hongkai↗
DOE OSTI2020

A light weight regularization for wave function parameter gradients in quantum Monte Carlo

The parameter derivative of the expectation value of the energy, ∂E/∂p, is a key ingredient in variational Monte Carlo (VMC) wave function optimization methods. In some cases, a naïve estimate of this derivative suffers from an infinite variance, which inhibits the efficiency of optimization methods that rely on a stable estimate of the derivative. In this work, we derive a simple regularization of the naïve estimator, which is trivial to implement in existing VMC codes, has finite variance, and a negligible bias, which can be extrapolated to zero bias with no extra cost. We use this estimator to construct an unbiased, finite variance estimation of ∂E/∂p for a multi-Slater–Jastrow trial wave function on the LiH molecule and in the optimization of a multi-Slater–Jastrow trial wave function on the CuO molecule. This regularized estimator is a simple and efficient estimator of ∂E/∂p for VMC optimization techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Machine Learning-Driven Reliability Estimation of PV Inverters Considering Alert-Ambient Variability

Weather-induced spatio-temporal degradation limits outdoor PV inverter lifetime and reliability, necessitating advanced data analysis. This study employs a top-down, data-driven approach utilizing multiple machine learning (ML) algorithms to estimate inverter reliability in a 1.4 MW PV power plant, considering factors such as irradiance, humidity, temperature, time of day, and weather conditions. An extensive alert dataset from 17 identical inverters, including alert types, propagation, and frequency, reveals significant correlations with environmental factors and inverter output power, enabling the construction of a performance reliability model. Dual-stage supervised-ML models are evaluated for accuracy, with the ‘classification-regression’ model by an artificial neural network (ANN) tested on the averaged “Alert-Ambient” dataset, which is outperformed by ‘clustering-regression’ models using random forest (RF) and K-Nearest Neighbors (KNN) on individual inverter datasets. K-means clustering applies principal component analysis to reduce dimensions, achieving improved accuracy beyond the 80% achieved by ANN on the averaged dataset. Second-stage regression estimates inverter reliability with a mean square error of 0.0195 on the averaged dataset and as low as 0.002 on individual inverter datasets using RF. Furthermore, these findings highlight the method's suitability for estimating PV inverter output reliability under ambient conditions, essential for digital twin development and related applications.

14 SOLAR ENERGY↗
DOE OSTI2016

Identification of Metabolic Pathway Systems

The estimation of parameters in even moderately large biological systems is a significant challenge. This challenge is greatly exacerbated if the mathematical formats of appropriate process descriptions are unknown. To address this challenge, the method of dynamic flux estimation (DFE) was proposed for the analysis of metabolic time series data. Under ideal conditions, the first phase of DFE yields numerical representations of all fluxes within a metabolic pathway system, either as values at each time point or as plots against their substrates and modulators. However, this numerical result does not reveal the mathematical format of each flux. Thus, the second phase of DFE selects functional formats that are consistent with the numerical trends obtained from the first phase. While greatly facilitating metabolic data analysis, DFE is only directly applicable if the pathway system contains as many dependent variables as fluxes. Because most actual systems contain more fluxes than metabolite pools, this requirement is seldom satisfied. Auxiliary methods have been proposed to alleviate this issue, but they are not general. Here we propose strategies that extend DFE toward general, slightly underdetermined pathway systems.

Genetics & Heredity↗
DOE OSTI2017

Practical Weak-lensing Shear Measurement with Metacalibration

Metacalibration is a recently introduced method to accurately measure weak gravitational lensing shear using only the available imaging data, without need for prior information about galaxy properties or calibration from simulations. The method involves distorting the image with a small known shear, and calculating the response of a shear estimator to that applied shear. The method was shown to be accurate in moderate-sized simulations with galaxy images that had relatively high signal-to-noise ratios, and without significant selection effects. In this work we introduce a formalism to correct for both shear response and selection biases. We also observe that for images with relatively low signal-to-noise ratios, the correlated noise that arises during the metacalibration process results in significant bias, for which we develop a simple empirical correction. To test this formalism, we created large image simulations based on both parametric models and real galaxy images, including tests with realistic point-spread functions. We varied the point-spread function ellipticity at the five-percent level. In each simulation we applied a small few-percent shear to the galaxy images. We introduced additional challenges that arise in real data, such as detection thresholds, stellar contamination, and missing data. We applied cuts on the measured galaxy properties to induce significant selection effects. Using our formalism, we recovered the input shear with an accuracy better than a part in a thousand in all cases.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

WE-G-204-07: Automated Characterization of Perceptual Quality of Clinical Chest Radiographs: Improvements in Lung, Spine, and Hardware Detection

Purpose: To develop and validate more robust methods for automated lung, spine, and hardware detection in AP/PA chest images. This work is part of a continuing effort to automatically characterize the perceptual image quality of clinical radiographs. [Y. Lin et al. Med. Phys. 39, 7019–7031 (2012)] Methods: Our previous implementation of lung/spine identification was applicable to only one vendor. A more generalized routine was devised based on three primary components: lung boundary detection, fuzzy c-means (FCM) clustering, and a clinically-derived lung pixel probability map. Boundary detection was used to constrain the lung segmentations. FCM clustering produced grayscale- and neighborhood-based pixel classification probabilities which are weighted by the clinically-derived probability maps to generate a final lung segmentation. Lung centerlines were set along the left-right lung midpoints. Spine centerlines were estimated as a weighted average of body contour, lateral lung contour, and intensity-based centerline estimates. Centerline estimation was tested on 900 clinical AP/PA chest radiographs which included inpatient/outpatient, upright/bedside, men/women, and adult/pediatric images from multiple imaging systems. Our previous implementation further did not account for the presence of medical hardware (pacemakers, wires, implants, staples, stents, etc.) potentially biasing image quality analysis. A hardware detection algorithm was developed using a gradient-based thresholding method. The training and testing paradigm used a set of 48 images from which 1920 51×51 pixel{sup 2} ROIs with and 1920 ROIs without hardware were manually selected. Results: Acceptable lung centerlines were generated in 98.7% of radiographs while spine centerlines were acceptable in 99.1% of radiographs. Following threshold optimization, the hardware detection software yielded average true positive and true negative rates of 92.7% and 96.9%, respectively. Conclusion: Updated segmentation and centerline estimation methods in addition to new gradient-based hardware detection software provide improved data integrity control and error-checking for automated clinical chest image quality characterization across multiple radiography systems.

60 APPLIED LIFE SCIENCES↗