Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID INJECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Multiple diagnostics in a high-pressure hydrogen microwave plasma torch

We present an experimental study of a hydrogen plasma produced by a microwave axial injection torch, launching the plasma in a helium-filled chamber. Three different diagnostic methods have been used to obtain the electron density and temperature as follows: The Stark intersection method of Balmer spectral lines (already tested in argon and helium plasmas); the modified Boltzmann-plot showing that the plasma is far from the local thermodynamic equilibrium but ruled by the excitation-saturation balance; and a study by the disturbed bilateral relations theory. All of these diagnostic techniques show a good agreement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

An experimental and computational analysis of combustion heat release transformation in dual fuel combustion

Dual fuel (DF) diesel-methane combustion, which employs a high-reactivity fuel (diesel) to ignite a low-reactivity fuel (methane), is a widely studied combustion strategy for internal combustion engines, with significant potential for engine-out emissions reductions without the need for major hardware modifications. A phenomenon, which has been reported in the DF literature, but not explained fully, is the transformation of the shape of the apparent heat release rate (AHRR) curve as the start of injection (SOI) of diesel is advanced beyond a certain threshold; coincidentally, this AHRR transformation is usually accompanied by a sharp decrease in engine-out emissions of oxides of nitrogen (NOx). The goal of the present work is to establish the underlying physical reason(s) that cause the AHRR transformation. The AHRR transformation was observed on a single cylinder research engine (SCRE) at an indicated mean effective pressure (IMEP) of 5 bar at a speed of 1500 rev/min. The transformation occurred over a range of SOIs from 330 to 320 crank angle degrees (CAD). While the 330 CAD SOI exhibited a typical two-stage AHRR curve, with a clearly definable first-stage peak followed by a second-stage AHRR with little-to-no low temperature heat release (LTHR) present and high engine-out NOx, the 320 CAD SOI exhibited a single-stage, Gaussian-like AHRR curve, with noticeable LTHR and at least one order-of-magnitude lower NOx emissions. Here, leveraging analysis of experimental data and three-dimensional computational fluid dynamic simulations, the authors show that the AHRR transformation is impacted mainly by differences in local equivalence ratio distributions within the cylinder at ignition onset for different diesel SOIs.

33 ADVANCED PROPULSION SYSTEMS↗

L – H transition trigger physics in ITER-similar plasmas with applied n = 3 magnetic perturbations

In this work, the L – H transition power threshold Ρ LH is observed to increase with applied n = 3 Resonant Magnetic Perturbations (RMP) in ITER-similar-shape (ISS) plasmas with balanced neutral beam torque injection in DIII-D. The increase is most pronounced with added ECH: Ρ LH increases with decreasing edge plasma collisionality as Ρ LH / Ρ LH-08 ~ ( v *) -0.5 , where Ρ LH-08 is the 2008 ITPA multi-machine power threshold scaling. This result raises concerns for H-mode access at low edge collisionality in ITER, where resonant magnetic perturbations (RMP) may have to be applied before the L – H transition to safely suppress the first ELM. Non-axisymmetric modifications with RMP include a simultaneous reduction of the radial electric field ( E r ) well depth and E × B shear. This can be attributed to increasing edge toroidal co-current rotation, and is consistent with substantially increased local long-wavelength turbulence [measured via Beam Emission Spectroscopy (BES)]. At high RMP perturbation strength the edge electric field E r reverses sign locally (becomes positive), with changes in dominant turbulence modes. Edge magnetic stochasticity provides an attractive explanation of the observed modifications, and the observed changes in toroidal rotation and E r are consistent with a simple fluid model describing radial electron current flow along stochastic fieldlines. The observed collisionality dependence of the L-mode edge electric field with applied RMP is also qualitatively consistent with this model. Reflectometry data indicate a significant reduction of the normalized L-mode radial density gradient a/L n at high RMP field with simultaneous increase in radial particle flux and electron thermal flux from power balance analysis. We conjecture that the increase of Ρ LH with RMP results from the combined effects of reduced E × B flow shear (increasing turbulent transport levels) and toroidal/poloidal flow modulation due to edge stochasticity. Initial experiments indicate that non-resonant n = 3 magnetic perturbations lead only to relatively small changes in E r , E × B shear and fluctuation characteristics, and have less impact on the L – H transition power threshold. In conclusion, this motivates further exploration of the RMP spectrum dependence of Ρ LH for possible mitigation of the observed threshold increase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a CO 2 Chemical Sensor for Downhole CO 2 Monitoring in Carbon Sequestration

Geologic storage of carbon dioxide (CO 2 ) has been proposed as a viable means for reducing anthropogenic CO 2 emissions. The means for geological sequestration of CO 2 is injection of supercritical CO 2 underground, which requires the CO 2 to remain either supercritical, or in solution in the water/brine present in the underground formation. However, there are aspects of geologic sequestration that need further study, particularly in regards to safety. To date, none of the geologic sequestration locations have been tested for storage integrity under the changing stress conditions that apply to the sequestration of very large amounts of CO 2 . Establishing environmental safety and addressing public concerns require widespread monitoring of the process in the deep subsurface. In addition, studies of subsurface carbon sequestration such as flow simulations, models of underground reactions and transports require a comprehensive monitoring process to accurately characterize and understand the storage process. Real-time information about underground CO 2 movement and concentration change is highly helpful for: (1) better understanding the uncertainties present in CO 2 geologic storage; (2) improvement of simulation models; and (3) evaluation of the feasibility of geologic CO 2 storage. Current methods to monitor underground CO 2 storage include seismic, geoelectric, isotope and tracer methods, and fluid sampling analysis. However, these methods commonly resulted low resolution, high cost, and the inability to monitor continuously over the long time scales of the CO 2 storage process. A preferred way of monitoring in-situ underground CO 2 migration is to continuous measure CO 2 concentration change in brine during the carbon storage process. An approach to obtain the real time information on CO 2 concentration change in formation solution is highly demanded in carbon storage to understand the CO 2 migration subsurface and to answer the public safety problem. The objective of the study is to develop a downhole CO 2 sensor that can in-situ, continuously monitor CO 2 concentration change in deep saline. The sensor is a Severinghaus-type CO 2 sensor with small size, which renders it can be embedded in monitoring well casing or integrated with pressure/temperature transducers, enabling the development of “smart” wells. The studies included: (1) prepare and characterize metal-oxide electrodes. Test the electrodes response to pH change. Investigate different ions and brine concentration effects on the electrode’s performance. Study the stability of the electrode in brine solution; (2) fabricate a downhole CO 2 sensor with the metal-oxide electrodes prepared in the laboratory. Test the performance of the CO 2 sensor in brine solutions. Study high pressure effects on the performance of the sensor; (3) design and conduct CO 2 /brine coreflooding experiments with the CO2 sensor. Monitor CO 2 movement along the core and test the performance of the sensor in coreflooding tests. Develop a data acquisition system that can digitize the sensor’s output voltage. Our completed research has resulted in deep understanding of downhole CO 2 sensor development and CO 2 monitoring in CO 2 storage process. The developed downhole CO 2 sensor included a metal-oxide electrode, a gas-permeable membrane, a porous steel cup, and a bicarbonate-based internal electrolyte solution. Iridium oxide-based electrode was prepared and used for preparation the CO 2 sensor. The prepared iridium oxide-based electrode displayed a linearly response to pH change. Different factors such as different ions and ions concentration, temperature, and pressure effects on the electrode performance on pH response were investigated. The results indicated that the electrode exhibited a good performance even in high salt concentration of produced water. To improve the electrode performance under high pressure, IrO 2 nanoparticles with the particle size in the range of 1-2 nm were prepared and electrodeposited on stainless steel substrate by cyclic voltammetry. It was observed that the thin film of iridium oxide was formed on the substrate surface and such iridium oxide-based electrode displayed excellent performance under high pressure for longer term. A downhole CO 2 sensor with the iridium oxide-based electrode was prepared. The working principle of the CO 2 sensor is based on the measurement of the pH change of the internal electrolyte solution caused by the hydrolysis of CO 2 and then determination of the CO 2 concentration in water. The prepared downhole CO 2 sensor had the size of diameter of 0.7 in. and length of 1.5 in. The sensor was tested under the pressures of 500 psi, 2,000 psi, and 3,000 psi. A linear correlation was observed between the sensor potential change and dissolved CO 2 concentration in water. The response time of the CO 2 sensor was in the range of 60-100 minutes. Further tests indicated that the CO 2 sensor exhibited good reproducibility under high pressure. A CO 2 /brine coreflooding system was constructed to simulate the real-world CO 2 storage process. The prepared downhole CO 2 sensor was loaded in the system to monitor CO 2 movement during CO 2 /brine coreflooding test. The results indicated that the sensor could detect CO 2 movement in the tests. Further studies showed that the sensor could be recovered by brine flooding after CO 2 /brine flushed the core. The results of the coreflooding tests demonstrated that the sensor had potential application for CO 2 monitoring in carbon sequestration. A data acquisition system for the downhoe CO 2 sensor was developed and coded. The system converted the sensor output signal into digital data and transported the data from downhole to wellhead surface. The data acquisition system was tested and evaluated in the laboratory with the prepared sensor for data collection.

36 MATERIALS SCIENCE↗

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗

Constraining fundamental physics with future CMB experiments

The Planck experiment will soon provide a very accurate measurement of cosmic microwave background anisotropies. This will let cosmologists determine most of the cosmological parameters with unprecedented accuracy. Future experiments will improve and complement the Planck data with better angular resolution and better polarization sensitivity. This unexplored region of the CMB power spectrum contains information on many parameters of interest, including neutrino mass, the number of relativistic particles at recombination, the primordial helium abundance, and the injection of additional ionizing photons by dark matter self-annihilation. We review the imprint of each parameter on the CMB and forecast the constraints achievable by future experiments by performing a Monte Carlo analysis on synthetic realizations of simulated data. We find that next generation satellite missions such as CMBPol could provide valuable constraints with a precision close to that expected in current and near future laboratory experiments. Finally, we discuss the implications of this intersection between cosmology and fundamental physics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Electric Power Generation from Low to Intermediate Temperature Resourcces

The UND-CLR Binary Geothermal Power Plant was a collaborative effort of the U.S. Department of Energy (DOE), Continental Resources, Inc. (CRL), Slope Electric Cooperative (SEC), Access Energy, LLC (AE), Basin Electric Cooperative (BEC), Olson Construction, the North Dakota Industrial Commission Renewable Energy Council (NDIC-REC), the North Dakota Department of Commerce Centers of Excellence Program (NDDC-COE), and the University of North Dakota (UND). The primary objective of project was to demonstrate/test the technical and economic feasibility of generating electricity from non-conventional, low-temperature (90 ºC to 150 °C) geothermal resources using binary technology. CLR provided the access to 98 ºC water flowing at 51 l s-1 at the Davis Water Injection Plan in Bowman County, ND. Funding for the project was from DOE –GTO, NDIC-REC, NDD-COE, and BEC. Logistics, on-site construction, and power grid access were facilitated by Slope Electric Cooperative and Olson Construction. Access Energy supplied prototype organic Rankine Cycle engines for the project. The potential power output from this project is 250 kW at a cost of $3,400 per kW. A key factor in the economics of this project is a significant advance in binary power technology by Access Energy, LLC. Other commercially available ORC engines have efficiencies 8 to 10 percent and produce 50 to 250 kW per unit. The AE ORC units are designed to generate 125 kW with efficiencies up to 14 percent and they can be installed in arrays of tens of units to produce several MW of power where geothermal waters are available. This demonstration project is small but the potential for large-scale development in deeper, hotter formations is promising. The UND team’s analysis of the entire Williston Basin using data on porosity, formation thicknesses, and fluid temperatures reveals that 4.0 x 1019 Joules of energy is available and that 1.36 x 109 MWh of power could be produced using ORC binary power plants. Much of the infrastructure necessary to develop extensive geothermal power in the Williston Basin exists as abandoned oil and gas wells. Re-completing wells for water production could provide local power throughout the basin thus reducing power loss through transmission over long distances. Water production in normal oil and gas operations is relatively low by design, but it could be one to two orders of magnitude greater in wells completed and pumped for water production. A promising method for geothermal power production recognized in this project is drilling horizontal open-hole wells in the permeable carbonate aquifers. Horizontal drilling in the aquifers increases borehole exposure to the resource and consequently increases the capacity for fluid production by up to an order of magnitude.

15 GEOTHERMAL ENERGY↗

Combustion Research I.1 Sprays, Flow, Heat Transfer and Turbulent Mixing

LANL is working with the Partnership for Advance Combustion Engines (PACE) a DOE sponsored consortium of national laboratories for the research and development for creating smarter engine design tools for sustainable transportation. Much of that effort is focused on heat, mass and momentum transfer within and engine. LANL’s focus in 2019, in particular under PACE has been spray modeling and engine mixture formulation, development of conjugate heat transfer analysis (heat transfer to the environment surrounding the combustion chamber). Our efforts relay on the Fast, Easy, Accurate and Robust Continuum Engineering (FEARCE) software developed at LANL as the next generation of engine modeling software for turbulent reactive and multiphase flow, a 2019 R&D 100 winner. This work is relevant to the DOE Vehicle Technologies Office efforts at addressing national energy security as well. Less dependence on petroleum products leads to greater energy security. By Environmental Protection Agency standards, some vehicles are now reaching 42–50 mpg mark. These are conventional gasoline engines. With continued investment and research into new technical innovations, the potential exists to save more than 4 million barrels of oil per day or approximately $200 to $400 million per day. This would be a significant decrease in emissions and use of petroleum and a very large stimulus to the U.S. economy. Better understanding of fuel injection and fuel–air mixing, thermodynamic combustion losses, and combustion/emission formation processes enhances our ability to minimize fuel use and unwanted emissions. Helping to accomplish this understanding, the FEARCE modeling program is working to provide state-of-theart capability for accurately simulating combustion processes: to have a predictive methodology in a software helping industry and researchers not only meet national goals on fuel usage and emissions, but global goals. In addition, a predictive, robust, and accurate capability for simulating the engine combustion process helps to minimize time and labor for development of new engine technology.

33 ADVANCED PROPULSION SYSTEMS↗

Appendix for the Final Technical Report - DE FE0009284

Carbon capture utilization storage (CCUS) is a potential technology to store anthropogenic emissions for CO 2 . Utilization often refers to CO 2 -enhanced oil recovery (CO 2 -EOR). An important factor in the success of CO 2 storage in saline formations or CO 2 -EOR reservoirs is ensuring that the storage occurs safely and is long-term. Assessment of well integrity has become more important for CCS and CO 2 -EOR as it has become apparent that wells represent the most likely migration pathway for CO 2 to leave a CCS storage unit or a CO 2 -EOR reservoir. Although wells represent a migration pathway they are also the best vehicle for employing technology monitoring CO 2 injection and storage. This contradiction of being a potential migration path and key monitoring technology leads to a need to understand how monitoring wells may be similar or different in comparison to other types of wells with respect to migration risk. The maturation and completion US Department of Energy sponsored research projects presents an opportunity to assess the integrity of monitoring wells that have been exposed to injected CO 2 . This paper discusses an integrity assessment of two monitoring wells in an operating CO 2 -EOR flood in Mississippi, USA. The CFU31F-2 and CFU31F-3 monitoring wells were constructed to test monitoring technologies in and above a commercial CO 2 -EOR project. The materials selected and the design of the well were optimized for monitoring. Carbonation in CFU31-F2 was seen as high as 7900 ft, above what was considered top of cement based on the logs. Time-lapse comparison of cement bond amplitude data and acoustic impedance maps show a deterioration of signal that implies a deterioration of cement bond or cement along much of the cemented annulus in the long-string section. Analysis of sidewall cores using XRD and LA-ICP-MS validated the log interpretation by confirming the degradation of cement (carbonation) along the casing-cement interface. The ultrasonic image maps also clearly identify the control lines and monitoring technology attached to the outside of the of the long-string casing on each well studied. The control lines appear as microdebonded or fluid filled vertical features implying that they could act as leakage pathways. The sidewall core through the control line at 10380 ft confirms that CO 2 is migrating along the control line with heavily carbonated cement at the control line interface. LA-ICP-MS and XRD on formation interface of the sidewall cores collected in both wells indicates that CO 2 is also moving of the cement-formation interface. LA-ICP-MS and XRD indicate that the amount carbonation in the center of the cores was less than the carbonation at the interfaces. Indicating that CO 2 is reaching the center of the cores by diffusing in from the interfaces and not migrating up from the reservoir though the porous matrix of the cement. This agrees with Duguid et al. [5] and Carey et al. [1] who have found that the interfaces in the well are more conductive than the porous network of the cement. Both the materials used to construct the well and the decision to attach monitoring technology to the outside of the well may have contributed to the migration of CO 2 along the interfaces. Careful consideration should be given to material selection to ensure that it does not degrade when in contact with the fluids in the reservoir and overlying strata. The addition of the control line on the outside of the casing complicated the cement placement and likely caused no cement to bond to the casing adjacent to the control line leading out of the reservoir. Further study of other wells with external lines should be conducted to see of the results of the construction of CFU31-F2 and -F3 is normal or an exception.

54 ENVIRONMENTAL SCIENCES↗

JET ROTATION DRIVEN BY MAGNETOHYDRODYNAMIC SHOCKS IN HELICAL MAGNETIC FIELDS

In this paper, we present a detailed numerical investigation of the hypothesis that a rotation of astrophysical jets can be caused by magnetohydrodynamic (MHD) shocks in a helical magnetic field. Shock compression of the helical magnetic field results in a toroidal Lorentz force component that will accelerate the jet material in the toroidal direction. This process transforms magnetic angular momentum (magnetic stress) carried along the jet into kinetic angular momentum (rotation). The mechanism proposed here only works in a helical magnetic field configuration. We demonstrate the feasibility of this mechanism by axisymmetric MHD simulations in 1.5 and 2.5 dimensions using the PLUTO code. In our setup, the jet is injected into the ambient gas with zero kinetic angular momentum (no rotation). We apply different dynamical parameters for jet propagation such as the jet internal Alfven Mach number and fast magnetosonic Mach number, the density contrast of the jet to the ambient medium, and the external sonic Mach number of the jet. The mechanism we suggest should work for a variety of jet applications, e.g., protostellar or extragalactic jets, and internal jet shocks (jet knots) or external shocks between the jet and the ambient gas (entrainment). For typical parameter values for protostellar jets, the numerically derived rotation feature looks consistent with the observations, i.e., rotational velocities of 0.1%-1% of the jet bulk velocity.

79 ASTRONOMY AND ASTROPHYSICS↗

MIXING IN SUPERSONIC TURBULENCE

In many astrophysical environments, mixing of heavy elements occurs in the presence of a supersonic turbulent velocity field. Here, we carry out the first systematic numerical study of such passive scalar mixing in isothermal supersonic turbulence. Our simulations show that the ratio of the scalar mixing timescale, {tau}{sub c}, to the flow dynamical time, {tau}{sub dyn} (defined as the flow driving scale divided by the rms velocity), increases with the Mach number, M, for M {approx}< 3, and becomes essentially constant for M {approx}> 3. This trend suggests that compressible modes are less efficient in enhancing mixing than solenoidal modes. However, since the majority of kinetic energy is contained in solenoidal modes at all Mach numbers, the overall change in {tau}{sub c}/{tau}{sub dyn} is less than 20% over the range 1 {approx}< M {approx}< 6. At all Mach numbers, if pollutants are injected at around the flow driving scale, {tau}{sub c} is close to {tau}{sub dyn}. This suggests that scalar mixing is driven by a cascade process similar to that of the velocity field. The dependence of {tau}{sub c} on the length scale at which pollutants are injected into flow is also consistent with this cascade picture. Similar behavior is found for the variance decay timescales for scalars without continuing sources. Extension of the scalar cascade picture to the supersonic regime predicts a relation between the scaling exponents of the velocity and the scalar structure functions, with the scalar structure function becoming flatter as the velocity scaling steepens with Mach number. Our measurements of the volume-weighted velocity and scalar structure functions confirm this relation for M {approx}< 2, but show discrepancies at M {approx}> 3, which arise probably because strong expansions and compressions tend to make scalar structure functions steeper.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

First modeling of strongly radiating WEST plasmas with SOLEDGE-EIRENE

We present first results of SOLEDGE-EIRENE modeling a strongly radiating plasma in the WEST tokamak. Using measurements from a reciprocating Langmuir probe we have determined the SOLEDGE input parameters, i.e. separatrix density at outboard midplane and radial transport coefficients typical of L-mode plasma. We have performed deuterium plasma simulations with presence of oxygen, injected from the core boundary into the simulation domain. The comparison between the radiated power measured from the bolometry in the divertor region and the one computed from SOLEDGE simulations seems to indicate a concentration of oxygen of about 2%. Moreover we have obtained good agreement between simulation results and experimental measurements on electron density and electron temperature profiles at the outer strike point. First qualitative analysis of spectroscopic synthetic diagnostic on D α signals is also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

JET PROPAGATIONS, BREAKOUTS, AND PHOTOSPHERIC EMISSIONS IN COLLAPSING MASSIVE PROGENITORS OF LONG-DURATION GAMMA-RAY BURSTS

We investigate the following by two-dimensional axisymmetric relativistic hydrodynamical simulations: (1) jet propagations through an envelope of a rapidly rotating and collapsing massive star, which is supposed to be a progenitor of long-duration gamma-ray bursts (GRBs); (2) breakouts and subsequent expansions into stellar winds; and (3) the accompanying photospheric emissions. We find that if the envelope rotates uniformly almost at the mass shedding limit, its outer part eventually stops contracting when the centrifugal force becomes large enough. Then another shock wave is formed, propagates outward, and breaks out of the envelope into the stellar wind. Whether the jet or the centrifugal bounce-induced shock breaks out earlier depends on the timing of jet injection. If the shock breakout occurs earlier, owing to a later injection, the jet propagation and subsequent photospheric emissions are affected substantially. We pay particular attention to observational consequences of the difference in the timing of jet injection. We calculate optical depths to find the location of photospheres, extracting densities, and temperatures at appropriate retarded times from the hydrodynamical data. We show that the luminosity and observed temperature of the photospheric emissions are both much lower than those reported in previous studies. Although luminosities are still high enough for GRBs, the observed temperatures are lower than the energy at the spectral peak expected by the Yonetoku relation. This may imply that energy exchanges between photons and matter are terminated deeper inside or that some non-thermal processes are operating to boost photon energies.

79 ASTRONOMY AND ASTROPHYSICS↗

Geologic Characterization for CO 2 Storage with Enhanced Oil Recovery in Northern Michigan

The Midwest Regional Carbon Sequestration Partnership (MRCSP) was founded in 2003 as part of the U.S. Department of Energy’s (DOE’s) Regional Carbon Sequestration Partnership initiative. Since its founding, MRCSP has made significant strides toward making CCUS a viable option for states in the region. The public/private consortium, funded through the DOE Regional Carbon Sequestration Initiative, brings together nearly 40 industry partners and 10 states. Battelle, as the project lead, oversees research, development and operations and coordinates activities among the partners. The incremental, phased approach has built a valuable knowledge base for the industry and paved the way for commercial-scale adoption of CCUS technologies. From 2008 to 2020, MRCSP Phase III focused on the development of large-scale injection projects. This report is part of a series of reports prepared under the Midwestern Regional Carbon Sequestration Partnership (MRCSP) Phase III (Development Phase). These reports summarize and detail the findings of the work conducted under the Phase III project. This report compiles the results of geologic characterization of late-stage reefs, active EOR reefs, and new EOR reefs in the Northern Niagaran Pinnacle Reef Trend (NNPRT) in Michigan to demonstrate developed methodologies, geologic variability, and reservoir potential for CO 2 storage. Conducting CO 2 injection and monitoring in these settings provide significant insights for addressing the project objectives: assessment of injectivity in complex carbonate reef deposits; assessing CO 2 trapping mechanisms in a closed reservoir system; assessing any final oil recovery from transitional or residual oil zones in a field where CO 2 flooding is nearing completion; evaluating the transition from EOR to storage of CO 2 ; assessing regional commercialization; assessing new technologies for tracking CO 2 , brine, and oil movements underground; and monitoring options in a closed reservoir with oil, residual oil, and water zones.

01 COAL, LIGNITE, AND PEAT↗

Assessment of Enhanced Oil Recovery Using Carbon Dioxide in Michigan Basin Silurian Pinnacle Reefs

The Midwest Regional Carbon Sequestration Partnership (MRCSP) has incorporated the work of geologic research teams (Geoteams) in its regional characterization, project planning and carbon dioxide (CO 2 ) injection implementation work since the partnership was established by the U.S. Department of Energy (DOE) in 2003. Over this 16-year period, the cohort of Geoteams has grown from five to ten states and has contributed to the characterization of geologic sequestration opportunities, refinement of reservoir and seal data, and supported injection efforts through both predictive and post-injection assessments. The Michigan team at Western Michigan University has provided technical analysis and support of the enhanced oil recovery (EOR) using carbon dioxide (CO 2 ) in the Northern Michigan Silurian Pinnacle reefs. With Core Energy, LLC as the industry partner, this project has assessed the potential for EOR in known fields in the Michigan Pinnacle reefs and the capacity for CO2 storage in the reef reservoirs as they are depleted and after reservoir abandonment. This project managed by Core Energy, LLC, involves the only commercial CO 2 Enhanced Oil Recovery floods within the MRCSP region. The Silurian pinnacle reef trend shows significant potential for CO 2 -EOR: this play is relatively new, with approximately 60% of the wells in the largest Niagaran fields still accessible. Most wells have modern logs and there are many cores, core analyses, pressure tests and produced water analyses available for study from these fields. These carbonate reservoirs in Michigan have produced sufficient oil to warrant evaluation for additional recovery efforts. The role of the Michigan team was to collect and analyze all relevant data about reservoir properties, including lithologic and depositional characteristics of the reservoir formations and porosity and fluid flow properties through different compartments in the reservoir. The team has also developed models that represent the geological and physical characteristics of the reservoir and seal system.

01 COAL, LIGNITE, AND PEAT↗

Computational Fluid Dynamics Simulation of Gasoline Compression Ignition

Gasoline compression ignition (GCI) is a low temperature combustion (LTC) concept that has been gaining increasing interest over the recent years owing to its potential to achieve diesel-like thermal efficiencies with significantly reduced engine-out nitrogen oxides (NOx) and soot emissions compared to diesel engines. In this work, closed-cycle computational fluid dynamics (CFD) simulations are performed of this combustion mode using a sector mesh in an effort to understand effects of model settings on simulation results. One goal of this work is to provide recommendations for grid resolution, combustion model, chemical kinetic mechanism, and turbulence model to accurately capture experimental combustion characteristics. Grid resolutions ranging from 0.7 mm to 0.1 mm minimum cell sizes were evaluated in conjunction with both Reynolds averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) based turbulence models. Solution of chemical kinetics using the multi-zone approach is evaluated against the detailed approach of solving chemistry in every cell. The relatively small primary reference fuel (PRF) mechanism (48 species) used in this study is also evaluated against a larger 312-species gasoline mechanism. Based on these studies the following model settings are chosen keeping in mind both accuracy and computation costs – 0.175 mm minimum cell size grid, RANS turbulence model, 48-species PRF mechanism, and multi-zone chemistry solution with bin limits of 5 K in temperature and 0.05 in equivalence ratio. With these settings, the performance of the CFD model is evaluated against experimental results corresponding to a low load start of injection (SOI) timing sweep. The model is then exercised to investigate the effect of SOI on combustion phasing with constant intake valve closing (IVC) conditions and fueling over a range of SOI timings to isolate the impact of SOI on charge preparation and ignition. Simulation results indicate that there is an optimum SOI timing, in this case -30?aTDC (after top dead center), which results in the most stable combustion. Advancing injection with respect to this point leads to significant fuel mass burning in the colder squish region, leading to retarded phasing and ultimately misfire for SOI timings earlier than -42?aTDC. On the other hand, retarding injection beyond this optimum timing results in reduced residence time available for gasoline ignition kinetics, and also leads to retarded phasing, with misfire at SOI timings later than -15?aTDC.

Energy conversion↗

Chemical Tool Peer Review Summary.

Chemical tracers are commonly used to characterize fracture networks and to determine the connectivity between the injection and production wells. Currently, most tracer experiments involve injecting the tracer at the injection well, manually collecting liquid samples at the wellhead of the production well, and sending the samples off for laboratory analysis. While this method provides accurate tracer concentration data, it does not provide information regarding the location of the fractures conducting the tracer between wellbores. The goal of this project is to develop chemical sensors and design a prototype tool to help understand the fracture properties of a geothermal reservoir by monitoring tracer concentrations along the depth of the well. The sensors will be able to detect certain species of the ionic tracers (mainly iodide) and pH in-situ during the tracer experiment. The proposed high-temperature (HT) tool will house the chemical sensors as well as a standard logging sensor package of pressure, temperature, and flow sensors in order to provide additional information on the state of the geothermal reservoir. The sensors and the tool will be able to survive extended deployments at temperatures up to 225 °C and high pressures to provide real-time temporal and spatial feedback of tracer concentration. Data collected from this tool will allow for the real-time identification of the fractures conducting chemical tracers between wellbores along with the pH of the reservoir fluid at various depths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

HFTS-1 (Final Report)

Despite the long history of hydraulic fracturing, the optimal number of fracturing stages during multi-stage fracture stimulation in horizontal wells can be a complex subject. In addition to the increased expense of multistage fracturing in horizontal wells, increasing the number of fracturing stages does not always correlate with a commensurate increase in production. The problem is the application of a uniform fracture stimulation design to all stages with no consideration for geological variations along the wellbore. The result is an inefficient use and costly waste of energy and water. Optimization of the fracturing process requires an understanding of the cause-and-effect relationship between fracturing parameters and local geological properties at a given location along the wellbore. Realizing that the generalized rock mechanics theories and hypotheses are not truly applicable to fractured and laminated shales, quantifiable impacts of a shale’s geomechanical and depositional features are a prerequisite for design and implementation of optimized hydraulic fractures. The overarching goal of this project is to understand and define the relationships of shale geology and fracture dynamics using detailed field data that includes coring of the fracture domain. Finally, resource recovery from shale formations is estimated to be less than fifteen percent. Research proposed in this project will establish the foundations for investigating enhanced recovery techniques for increased resource recovery in existing fracture treated wells. Natural gas as an EOR fluid is in the initial stages of being used broadly in the oil and gas industry and as such, many aspects of the process need to be researched and addressed prior to widespread acceptance. In addition, re-fracturing techniques, particularly using cemented liners also need to be further investigated. This project explores several of these EOR techniques in greater detail, not just at the theoretical level, but through actual field test sites. This report delves into the research program, identified tasks, several studies, observations, results, and conclusions under the Hydraulic Fracturing Test Site (HFTS) project. This test project is subdivided into three distinct phases and each phase is discussed in detail under separate sections. The original test site for Phase 1 as well as the Phase 2 site are in Midland Basin in Texas and operated by Laredo Petroleum. In the first two phases, the program targeted the Wolfcamp formation in Midland Basin. Phase 3 of the study targeted the EagleFord play in South Texas with Devon Energy as the operator. Significant conclusions from this study include: 1) lateral and vertical fracture growth mapping as well as proppant transport behavior, 2) Use of field gas and its applicability for huff n puff EOR injection in the Midland Basin, 3) Development and validation of proppant log, both at core scale as well as in-fill well implementation by analyzing drilling mud return samples, 4) Applicability of liner refracturing including best practices for enhanced unit level productivity. This report will detail all these studies as well as technical results and conclusions from said studies. These include general subsurface characterization work, completion designs as implemented, studies looking at fracture geometry, high resolution microseismic study, advanced crosswell strain mapping studies including drainage characterization, core characterization results, proppant analysis (core and observation wells), geochemistry, etc. to name a few.

02 PETROLEUM↗