Search NASA⌕ Search

SEARCH · Search NASA

Results for “PIPES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Laser Doppler measurements of laminar and turbulent flow in a pipe bend

The streamwise components of velocity in the flow through a ninety degree bend of circular cross section for which the ratio of radius of curvature to diameter is 2.8 were measured. The development of strong pressure driven secondary flow in the form of a pair of counter rotating vortices in the steamwise direction is shown. Refractive index matching at the fluid wall interface was not employed; the displacement of the measurement volume due to refraction is allowed for in simple geometrical calculations.

Enayet, M. M.↗

Analysis of combustion spectra containing organ pipe tone by cepstral techniques

Signal reinforcements and cancellations due to standing waves may distort constant bandwidth combustion spectra. Cepstral techniques previously applied to the ground reflection echo problem are used to obtain smooth broadband data and information on combustion noise propagation. Internal fluctuating pressure measurements made using a J47 combustor attached to a 6.44 m long duct are analyzed. Measurements made with Jet A and hydrogen fuels are compared. The acoustic power levels inferred from the measurements are presented for a range of low heat release rate operating conditions near atmospheric pressure. For these cases, the variation with operating condition of the overall acoustic broadband power level for both hydrogen and Jet A fuels is consistent with previous results showing it was proportional to the square of the heat release rate. However, the overall acoustic broadband power level generally is greater for hydrogen than for Jet A.

Miles, J. H.↗

Heat pipe thermal switch

A thermal switch for controlling the dissipation of heat between a body is described. The thermal switch is comprised of a flexible bellows defining an expansible vapor chamber for a working fluid located between an evaporation and condensation chamber. Inside the bellows is located a coiled retaining spring and four axial metal mesh wicks, two of which have their central portions located inside of the spring while the other two have their central portions located between the spring and the side wall of the bellows. The wicks are terminated and are attached to the inner surfaces of the outer end walls of evaporation and condensation chambers respectively located adjacent to the heat source and heat sink. The inner surfaces of the end walls furthermore include grooves to provide flow channels of the working fluid to and from the wick ends. The evaporation and condensation chambers are connected by turnbuckles and tension springs to provide a set point adjustment for setting the gap between an interface plate on the condensation chamber and the heat sink.

Wolf, D. A.↗

Acceptance criteria for welds in ASTM A106 grade B steel pipe and plate

Based on the RECERT Program findings, NASA-Langley funded a fatigue study of code-unacceptable welds. Usage curves were developed which were based on the structural integrity of the welds. The details of this study are presented in NASA CR-178114. The information presented is a condensation and reinterpretation of the information in NASA CR-178114. This condensation and reinterpretation generated usage curves for welds having: (1) indications 0.20 -inch deep by 0.40-inch long, and (2) indications 0.195-inch deep by 8.4-inches long. These curves were developed using the procedures used in formulating the design curves in Section VIII, Division 2 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code.

Hudson, C. M.↗

Helium isotopic variability within single diamonds from the Orapa kimberlite pipe

The possible relationships between diamond mineralogy and helium isotopes were investigated by measuring the distribution and isotopic composition of He in a suite of well-characterized one-carat diamonds from the Orapa kimberlite, Botswana. The results of crushing in vacuo experiments indicated that most of He was contained in the matrix, rather than in the inclusions of the diamonds. Step-heating of individual diamonds at 2000 C released He of He-3/He-4 ratios that differed by up to a factor of 100 among the two heating steps, revealing large isotopic variations within individual diamonds. It is suggested that this internal isotopic variability is the result of stepwise graphitization: the first heating step initiates graphitization which nucleates around defects in a diamond, and the second step graphitizes the relatively defect-free regions of the diamond. This explanation predicts that the highest He-3/He-4 ratios should be found in most perfect crystals.

Kurz, Mark D.↗

Modeling of a pulsed fluid column and coupled piping with structural finite elements

Structural finite elements have been used to model the coupled fluidic-structural response of a liquid oxygen (LOX) feedline at a rocket engine test facility. The model simulates the effects of Pogo pulsing, a test procedure which uses a piston in a side branch to impart an oscillatory pressure pulse to the LOX column as it feeds the engine. In addition to the feedline's structural characteristics, the model accounts for the mass and axial stiffness of the fluid column, the oscillatory pulse of the piston, and the hydraulic impedance of the rocket engine. The model was used to determine the relations between piston stroke, pressure oscillation at the engine inlet, and structural excitation of the feedline. This paper develops the concepts employed by the model.

Saxon, J. B.↗

Transient analysis of a capillary pumped loop heat pipe

A bench-top Capillary Pumped Loop (CPL) test system has been developed and tested to investigate the transient mode operation of this system by applying a step power input to the evaporators. Tests were conducted at several power input and evaporator inlet subcooling combinations. In addition, a lumped-heat-capacity model of the CPL test system has been presented which is used for predicting qualitatively the transient operation characteristics. Good agreement has been obtained between the predicted and the measured temperature variations. A simple evaporator inlet subcooler model has also been developed to study effects of inlet subcooling on the steady-state evaporator wall temperature. Results were compared with the test data collected.

Kiper, A. M.↗

Tone generation by aeroacoustic sources in pipes with flow

Sound production by axisymmetric ring cavities in internal flow has been investigated experimentally. These ring sources generate sound when the acoustic motion in the cavity is in resonance in one of many possible modes. Experimental results agree with predictions of a model eddy-driven oscillator. It is observed that the standing waves produced by reflections from regions upstream and downstream of the source are adjusted by the source such that the source is at a pressure antinode at the condition of maximum sound emission.

Shakkottai, P.↗

Time variant analysis of large scale constrained rotorcraft systems dynamics - An exploitation of IBM-3090 vector-processor's pipe-lining feature

A generalized algorithmic procedure is presented for handling the constraints in transmissions, which are treated as a multibody system of interconnected rigid/flexible bodies. The type of constraints are classified based on the interconnection of the bodies, assuming one or more points of contact to exist between them. The method is explained through flow charts and configuration/interaction tables. A significant increase in speed of execution is achieved by vectorizing the developed code in computationally intensive areas. The study of an example consisting of two meshing disks rotating at high angular velocity is carried out. The dynamic behavior of the constraint forces associated with the generalized coordinates of the system are plotted by selecting various modes. Applications are intended for the study of dynamic and subsequent prediction of constraint forces at the gear teeth contacting points in helicopter transmissions with the aim of improving performance dependability.

Amirouche, F. M. L.↗

Physics of heat pipe rewetting

Although several studies have been made to determine the rewetting characteristics of liquid films on heated rods, tubes, and flat plates, no solutions are yet available to describe the rewetting process of a hot plate subjected to a uniform heating. A model is presented to analyze the rewetting process of such plates with and without grooves. Approximate analytical solutions are presented for the prediction of the rewetting velocity and the transient temperature profiles of the plates. It is shown that the present rewetting velocity solution reduces correctly to the existing solution for the rewetting of an initially hot isothermal plate without heating from beneath the plate. Numerical solutions have also been obtained to validate the analytical solutions.

Chan, S. H.↗

Graphite Fiber/Copper Matrix Composites for Space Power Heat Pipe Fin Applications

High specific thermal conductivity (thermal conductivity divided by density) is a major design criterion for minimizing system mass for space power systems. For nuclear source power systems, graphite fiber reinforced copper matrix (Gr/Cu) composites offer good potential as a radiator fin material operating at service temperatures above 500 K. Specific thermal conductivity in the longitudinal direction is better than beryllium and almost twice that of copper. The high specific thermal conductivity of Gr/Cu offers the potential of reducing radiator mass by as much as 30 percent. Gr/Cu composites also offer the designer a range of available properties for various missions and applications. The properties of Gr/Cu are highly anisotropic. Longitudinal elastic modulus is comparable to beryllium and about three times that of copper. Thermal expansion in the longitudinal direction is near zero, while it exceeds that of copper in the transverse direction.

McDanels, David L.↗

Horton, pipe hydraulics, and the atmospheric boundary layer (The Robert E. Horton Memorial Lecture)

The early stages of Horton's scientific career which provided the opportunity and stimulus to delve into the origins of some contemporary concepts on the atmospheric boundary layer are reviewed. The study of Saph and Schoder provided basis for the experimental verification and validation of similarity by Blasius, Staton and Pannel, and for the subsequent developments that led to the present understanding of the turbulent boundary layer. Particular attention is given to incorporation of similarity and scaling in the analysis of turbulent flow.

Brutsaert, Wilfried↗