Results for “Phase separation” — Page 89

DOE OSTI2024

Sputter deposition of Ta 1 W 1 Au 1 Bi 7 films for next generation hohlraums

Hohlraum simulation predicts a higher x-ray drive from Ta 1 W 1 Au 1 Bi 7 compared with our current Au hohlraum. Here, we study the effect of deposition process parameters including deposition rate, working pressure, target-to-substrate distance, substrate bias, and substrate temperature on the microstructure of Ta1W1Au1Bi7 films deposited by direct current magnetron sputtering onto planar substrates. We found that the substrate temperature has a pronounced effect on the film microstructure. This is attributed to the Bi low melting point (271°C) causing its adatom mobility to be strongly dependent on the substrate temperature. Additionally, we observed phase separation for films deposited with a high substrate bias. These results have important implications for the development of a robust Ta 1 W 1 Au 1 Bi 7 hohlraum fabrication process.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

09 BIOMASS FUELS↗

DOE OSTI2023

High Density Thermal Energy Storage by Highly Stable Glauber’s Salt Composites with Low Supercooling for Building-Scale Application

Phase change materials (PCM) are a promising candidate for thermal energy storage in building infrastructure, enabling grid-integrated peak load shaving by utilizing energy production in off-peak hours. Glauber’s salt (Na2SO4.10H2O, Sodium sulfate hydrate) are highly attractive due to their high energy storage capacity and low cost but Glauber’s salt suffers from long-standing challenges including high supercooling ( > 15oC) and low thermal cyclic stability, which is a major setback for practical building-scale energy storage applications. Here, we developed a unique ionic molecular nucleating agent for Glauber’s salt which reduced the supercooling temperature to less than 5oC. By combining this nucleated SSD with a polymer, phase segregation of salt hydrate for over 100 thermal cycles without degradation was achieved. Key was that the polymer confined the SSD crystals, preventing phase separation. In addition, we applied our stable Glauber’s salt composite in a miniatured building model and demonstrate that our PCM composite can be utilized for real-world building infrastructure.

additives↗

DOE OSTI2024

Hydrogel-Salt Hydrate Composite for Highly Stable Heat Energy Storage with Reduced Supercooling

Phase change materials (PCM) have potential for use in thermal energy storage in buildings, medical devices, and water heat pumps. Sodium sulfate hydrate (SSD) is appealing due to its high energy storage capability and affordability. However, SSD has issues including high supercooling (> 15°C) and low thermal cyclic stability. In this study, we introduced an ionic molecular nucleating agent that decreases the supercooling temperature to under 2°C. When this SSD was combined with a hydrogel, it maintained its thermal energy storage capacity for over 100 cycles without any decline. The success is attributed to the polymer confining the SSD crystals, preventing large-scale phase separation and the nucleating agent which resulted in nucleation of many small SSD crystals at small undercoolings rather than a small number of larger crystals. As a proof-of-application, we synthesized this composite at a kg scale and demonstrated its properties in a close to real-world demonstration.

chemical composition, thermodynamics↗

DOE OSTI2026

Epitaxy of Beta-Ga2O3 on Highly-Offcut (Greater than 10 Degrees) Substrates

Beta-Ga2O3 has emerged as a leading candidate for next-generation power electronics, radio frequency (RF) switches, and extreme environment electronics due to a wide band gap (4.6 - 4.9 eV), high dopability (approximately 40 meV activation energy for an isolated silicon donor), and melt growth characteristics resulting in commercially available 4-inch substrates and commercial demonstrations of 6-inch substrates by multiple techniques. The (100) surface of Ga2O3 is highly desirable from a device and epitaxy standpoint - bulk growth of (100) material is more scalable than (010), the surface is nearly lattice-matched to p-type partner NiO, and Al2O3 incorporates at higher concentrations without phase separation. However, the epitaxial growth rate on (100) surfaces is less than 10% of other faces due to weak bonding and favorable desorption. Recent demonstrations have shown growth rate improvements from 0.4 nm/min to 1.5 nm/min by growing on (100) wafers that are offcut 6 degrees in the -c direction.1 These films show step-flow growth from (-201) step-edges and high electron mobility. Despite these exciting results, offcuts greater than 6 degrees have not been explored due to the waste associated with grinding and polishing large offcuts. In this talk we will discuss the molecular beam epitaxy (MBE) growth and properties of Beta-Ga2O3 grown on (100) substrates offcut in the -c direction up to 13.4 degrees. These large offcuts are enabled by edge-fed film-defined growth (EFG) where the offcut is grown into the surface by pulling the crystal through the EFG die with the seed crystal rotated by the desired offcut angle. We will demonstrate that 13.4 degrees offcut substrates still exhibit a terraced (100) surface, and that a >10x increase (4.8 nm/min) in growth rate is achieved. As previously reported on lower offcuts, we observe 100% reversal of substrate twin domains around the (001) direction at the substrate-epilayer interface. We will discuss electrical properties including record-low (by MBE) unintentional doping densities of < 5E15 cm-3.

36 MATERIALS SCIENCE↗

DOE OSTI2023

SPRUCE Climate Warming and Elevated CO2 Rapidly Alter Peatland Soil Carbon Sources and Stability: Supporting Data

This data set reports a suite of complementary biogeochemical analyses of peat samples from the SPRUCE (Spruce and Peatland Responses Under Changing Environments) experiment. Results were collected using quantitative molecular analysis of bulk soil carbon to assess the stability of soil organic carbon following whole-ecosystem warming and exposure to elevated carbon dioxide concentrations (eCO2). Targeted soil organic carbon components include solvent-extractable compounds (alkanoic acids, alkanols, alkanes, steroids, and terpenoids), ester-bound hydrolysable biopolymers (cutin and suberin markers), lignin phenols, and pyrogenic carbon. Bulk peat samples were analysed by Soxhlet extraction and solid phase separation for solvent-extractable compounds, alkaline hydrolysis to extract hydrolysable biopolymers, copper (II) oxide oxidation to extract lignin phenols and benzene polycarboxylic acids (BPCAs) as an approximation of pyrogenic carbon. Samples were analysed by gas chromatography (GC) equipped with a flame ionization detector (GC-FID) and compound identification was performed on GC coupled to mass selective detector (MS) for solvent-extractable compounds, ester-bound hydrolysable biopolymers and lignin phenols, and high-performance liquid chromatograph (HPLC) for pyrogenic carbon. Results are presented in Ofiti et al. (accepted). The experimental work was conducted on samples collected in August 2018 at the SPRUCE climate manipulation experiment in northern Minnesota, 40 km north of Grand Rapids, in the USDA Forest Service Marcell Experimental Forest (MEF). Samples were collected and later analysed in a 10 cm increments over 0 to 50 cm depth and 25 cm intervals from 50 to 75 cm. Samples were analyzed for lignin phenols over 0 to 30 cm depth. This data set contains one file in comma separate (*.csv) format. This dataset contains data used to produce: Ofiti, N.O.E., Schmidt, M.W.I., Abiven, S., Hanson, P.J., Iversen, C.M., Wilson, R.M., Kostka, J.E., Wiesenberg, G.L.B., Malhotra, A. 2023. Climate warming and elevated CO2 rapidly alter peatland soil carbon sources and stability. Nat Commun 14, 7533. https://doi.org/10.1038/s41467-023-43410-z.

SPRUCE experiment, Marcell Experimental Forest, so↗

DOE OSTI2024

Supporting data for Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

Li, Shuyun↗

DOE OSTI2026

Tabulated data for Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation

Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents. This is the tabulated data for the paper

biorefining↗

DOE OSTI2026

Calculation of monomer yields, verification of PG concentration approximation, catalyst comparison for neat aromatic RCF, SEM micrographs for postreaction pulps, yields of aqueous-phase sugar derivatives after PG-H2O RCF, reactor pressure transients, GPC comparing pre- and postreaction organic solvent composition, PG-H2O miscibility testing, GPC probing dimer/oligomer fractionation in PG-H2O mixtures for

Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents.

biorefining↗

DOE OSTI2026

Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation

Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents.

biorefining↗

DOE OSTI2023

A review on experimentally observed mechanical and microstructural characteristics of interfaces in multi-material laser powder bed fusion

Additive manufacturing (AM) is a revolutionary technology. One of the key AM categories, metal powder-based fusion processes, has many advantages compared to conventional methods for fabricating structural materials, such as permitting increased geometric complexity. While single material metal powder AM has advanced significantly in the past decade, multi-material AM is gradually attracting more attention owing to the recent breakthrough in multi-material feedstock delivery and the growing interest of fabricating functionally graded components. Multi-material AM offers an alternative route for applications that require location dependent material properties and high geometrical complexity. The AM community has invented several ways to achieve compositional gradients and discrete boundaries in two and three dimensions using mechanical spreading, nozzle-based, electrophotographic, and hybrid techniques. This article reviews the current state of laser powder bed fusion based multi-material AM of metals with focuses on the characteristics of the material interface as well as the properties and performance of the AM built functionally graded materials. We show the common challenges and issues related to material transitions, such as defects, segregation, phase separation, and the efficacy of some potential solutions including material and process optimizations. Additionally, this study evaluates the applicability and limitations of the existing testing standards and methods for measuring mechanical performance of functionally graded materials. Finally, we discuss mechanical testing development opportunities, which can help multi-material AM move towards higher technological maturity. In general, we find that the link between gradient microstructure and mechanical properties is not well understood or studied and suggest several mechanical tests that may better inform this knowledge gap.

42 ENGINEERING↗

DOE OSTI2023

Hard–Soft Core–Shell Architecture Formation from Cubic Cobalt Ferrite Nanoparticles

Cubic bi-magnetic hard–soft core–shell nanoarchitectures were prepared starting from cobalt ferrite nanoparticles, prevalently with cubic shape, as seeds to grow a manganese ferrite shell. The combined use of direct (nanoscale chemical mapping via STEM-EDX) and indirect (DC magnetometry) tools was adopted to verify the formation of the heterostructures at the nanoscale and bulk level, respectively. The results showed the obtainment of core–shell NPs (CoFe 2 O 4 @MnFe 2 O 4 ) with a thin shell (heterogenous nucleation). In addition, manganese ferrite was found to homogeneously nucleate to form a secondary nanoparticle population (homogenous nucleation). This study shed light on the competitive formation mechanism of homogenous and heterogenous nucleation, suggesting the existence of a critical size, beyond which, phase separation occurs and seeds are no longer available in the reaction medium for heterogenous nucleation. These findings may allow one to tailor the synthesis process in order to achieve better control of the materials’ features affecting the magnetic behaviour, and consequently, the performances as heat mediators or components for data storage devices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Structure-Related Electronic and Magnetic Properties in Ultrathin Epitaxial Ni x Fe 3–x O 4 Films on MgO(001)

Off-stoichiometric Ni x Fe 3–x O 4 ultrathin films (x < 2.1) with varying Ni content x and thickness 16 (±2) nm were grown on MgO(001) by reactive molecular beam epitaxy. Synchrotron-based high-resolution X-ray diffraction measurements reveal vertical compressive strain for all films, resulting from a lateral pseudomorphic adaption of the film to the substrate lattice without any strain relaxation. Complete crystallinity with smooth interfaces and surfaces is obtained independent of the Ni content x. For x < 1 an expected successive conversion from Fe 3 O 4 to NiFe 2 O 4 is observed, whereas local transformation into NiO structures is observed for films with Ni content x > 1. However, angle-resolved hard X-ray photoelectron spectroscopy measurements indicate homogeneous cationic distributions without strictly separated phases independent of the Ni content, while X-ray absorption spectroscopy shows that also for x > 1, not all Fe 2+ cations are substituted by Ni 2+ cations. The ferrimagnetic behavior, as observed by superconducting quantum interference device magnetometry, is characterized by decreasing saturation magnetization due to the formation of antiferromagnetic NiO parts.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Impact- and Thermal-Resistant Epoxy Resin Toughened with Acacia Honey

High performance polymers with bio-based modifiers are promising materials in terms of applications and environmental impact. In this work, raw acacia honey was used as a bio-modifier for epoxy resin, as a rich source of functional groups. The addition of honey resulted in the formation of highly stable structures that were observed in scanning electron microscopy images as separate phases at the fracture surface, which were involved in the toughening of the resin. Structural changes were investigated, revealing the formation of a new aldehyde carbonyl group. Thermal analysis confirmed the formation of products that were stable up to 600 °C, with a glass transition temperature of 228 °C. An energy-controlled impact test was performed to compare the absorbed impact energy of bio-modified epoxy containing different amounts of honey with unmodified epoxy resin. The results showed that bio-modified epoxy resin with 3 wt% of acacia honey could withstand several impacts with full recovery, while unmodified epoxy resin broke at first impact. The absorbed energy at first impact was 2.5 times higher for bio-modified epoxy resin than it was for unmodified epoxy resin. In this manner, by using simple preparation and a raw material that is abundant in nature, a novel epoxy with high thermal and impact resistance was obtained, opening a path for further research in this field.

36 MATERIALS SCIENCE↗

DOE OSTI2014

The Effect of Salt on the Complex Coacervation of Vinyl Polyelectrolytes

Complex coacervation is an electrostatically-driven phase separation phenomenon that is utilized in a wide range of everyday applications and is of great interest for the creation of self-assembled materials. Here, we utilized turbidity to characterize the effect of salt type on coacervate formation using two vinyl polyelectrolytes, poly(acrylic acid sodium salt) (pAA) and poly(allylamine hydrochloride) (pAH), as simple models for industrial and biological coacervates. We confirmed the dominant role of salt valence on the extent of coacervate formation, while demonstrating the presence of significant secondary effects, which can be described by Hofmeister-like behavior. These results revealed the importance of ion-specific interactions, which are crucial for the informed design of coacervate-based materials for use in complex ionic environments, and can enable more detailed theoretical investigations on the role of subtle electrostatic and thermodynamic effects in complex coacervation.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effect of Carboxylic Acids on Corrosion of Type 410 Stainless Steel in Pyrolysis Bio-Oil

Biomass-derived oils are renewable fuel sources and commodity products and are proposed to partially or entirely replace fossil fuels in sectors generally considered difficult to decarbonize such as aviation and maritime propulsion. Bio-oils contain a range of organic compounds with varying functional groups which can lead to polarity-driven phase separation and corrosion of containment materials during processing and storage. Polar compounds, such as organic acids and other oxygenates, are abundant in bio-oils and are considered corrosive to structural alloys, particularly to those with a low-Cr content. To study the corrosion effects of small carboxylic acids present in pyrolysis bio-oils, type 410 stainless steel (SS410) specimens were exposed in bio-oils with varying formic, acetic, propionic and hexanoic acid contents at 50 °C during 48 h exposures. The specific mass change data show a linear increase in mass loss with increasing formic acid concentration. Interestingly, a mild corrosion inhibition effect on the corrosion of SS410 specimens was observed with the addition of acetic, propionic and hexanoic acids in the bio-oil.

09 BIOMASS FUELS↗

DOE OSTI2016

Effects of solvent additive on “s-shaped” curves in solution-processed small molecule solar cells

A novel molecular chromophore, p-SIDT(FBTThCA8) 2 , is introduced as an electron-donor material for bulk heterojunction (BHJ) solar cells with broad absorption and near ideal energy levels for the use in combination with common acceptor materials. It is found that films cast from chlorobenzene yield devices with strongly s-shaped current–voltage curves, drastically limiting performance. We find that addition of the common solvent additive diiodooctane, in addition to facilitating crystallization, leads to improved vertical phase separation. This yields much better performing devices, with improved curve shape, demonstrating the importance of morphology control in BHJ devices and improving the understanding of the role of solvent additives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

The 100 pc White Dwarf Sample in the SDSS Footprint

In this work, we present follow-up spectroscopy of 711 white dwarfs within 100 pc, and we present a detailed model atmosphere analysis of the 100 pc white dwarf sample in the Sloan Digital Sky Survey footprint. Our spectroscopic follow-up is complete for 83% of the white dwarfs hotter than 6000 K, where the atmospheric composition can be constrained reliably. We identify 1508 DA white dwarfs with pure hydrogen atmospheres. The DA mass distribution has an extremely narrow peak at 0.59 M ⊙ and reveals a shoulder from relatively massive white dwarfs with M = 0.7–0.9 M ⊙. Comparing this distribution with binary population synthesis models, we find that the contribution from single stars that form through mergers cannot explain the overabundance of massive white dwarfs. In addition, the mass distribution of cool DAs shows a near absence of M > 1 M ⊙ white dwarfs. The pile-up of 0.7–0.9 M ⊙ and the disappearance of M > 1 M ⊙ white dwarfs is consistent with the effects of core crystallization. Even though the evolutionary models predict the location of the pile-up correctly, the delay from the latent heat of crystallization by itself is insufficient to create a significant pile-up, and additional cooling delays from related effects like phase separation are necessary. We also discuss the population of infrared-faint (ultracool) white dwarfs and demonstrate for the first time the existence of a well-defined sequence in color and magnitude. Curiously, this sequence is connected to a region in the color–magnitude diagrams where the number of white dwarfs with a helium-dominated atmosphere is low. This suggests that the infrared-faint white dwarfs likely have mixed H/He atmospheres.

79 ASTRONOMY AND ASTROPHYSICS↗