Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polymer Science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Biorenewable and circular polydiketoenamine plastics

Amid growing concerns over the human health and environmental impacts of plastic waste, the most promising solution would be to build a circular plastics economy where sustainability considerations dictate the full life cycle of plastics use including replacing petrochemicals with biorenewables. Here we show that by incorporating the polyketide triacetic acid lactone (TAL) in polydiketoenamines (PDK) we increase the working temperature of these circular plastics, opening the door wider to applications where circularity is urgently needed. By varying the number of carbons of TAL-derived monomers, both polymer properties and recycling efciency are afected. Simply using glucose as the main carbon source, we engineered a process for producing bioTAL under fed-batch fermentation. Furthermore, a systems analysis of this bioprocess under diferent scenarios quantifes the environmental and economic benefts of PDK plastics and the risks when implemented at an industrial scale, providing opportunities in biorenewable circularity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recycling polyolefin plastic waste at short contact times via rapid joule heating

Abstract The chemical deconstruction of polyolefins to fuels, lubricants, and waxes offers a promising strategy for mitigating their accumulation in landfills and the environment. Yet, achieving true recyclability of polyolefins into C 2 -C 4 monomers with high yields, low energy demand, and low carbon dioxide emissions under realistic polymer-to-catalyst ratios remains elusive. Here, we demonstrate a single-step electrified approach utilizing Rapid Joule Heating over an H-ZSM-5 catalyst to efficiently deconstruct polyolefin plastic waste into light olefins (C 2 -C 4 ) in milliseconds, with high productivity at much higher polymer-to-catalyst ratio than prior work. The catalyst is essential in producing a narrow distribution of light olefins. Pulsed operation and steam co-feeding enable highly selective deconstruction (product fraction of >90% towards C 2 -C 4 hydrocarbons) with minimal catalyst deactivation compared to Continuous Joule Heating. This laboratory-scale approach demonstrates effective deconstruction of real-life waste materials, resilience to additives and impurities, and versatility for circular polyolefin plastic waste management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocrystalline SiC and Ti 3 SiC 2 Alloys for Reactor Materials: Thermal and Mechanical Properties

SiC-polymers (pure polycarbosilane and polycarbosilane filled with SiC-particles) are being combined with Si and TiC powders to create a new class of polymer-derived ceramics for consideration as advanced nuclear materials in a variety of applications. Compared to pure SiC these materials have increased fracture toughness with only slightly reduced thermal conductivity. Future work with carbon nanotube (CNT) mats will be introduced with the potential to increase the thermal conductivity and the fracture toughness. At present, this report documents the fabrication of a new class of monolithic polymer derived ceramics, SiC + SiC/Ti 3 SiC 2 dual phase materials. The fracture toughness of the dual phase material was measured to be significantly greater than Hexoloy SiC using indentation fracture toughness testing. However, thermal conductivity of the dual phase material was reduced compared to Hexoloy SiC, but was still appreciable, with conductivities in the range of 40 to 60 W/(m K). This report includes synthesis details, optical and scanning electron microscopy images, compositional data, fracture toughness, and thermal conductivity data.

36 MATERIALS SCIENCE↗

Crazing of nanocomposites with polymer-tethered nanoparticles

The crazing behavior of polymer nanocomposites formed by blending polymer grafted nanoparticles with an entangled polymer melt is studied by molecular dynamics simulations. We focus on the three key differences in the crazing behavior of a composite relative to the pure homopolymer matrix, namely, a lower yield stress, a smaller extension ratio, and a grafted chain length dependent failure stress. The yield behavior is found to be mostly controlled by the local nanoparticle-grafted polymer interfacial energy, with the grafted polymer-polymer matrix interfacial structure being of little to no relevance. Increasing the attraction between nanoparticle core and the grafted polymer inhibits void nucleation and leads to a higher yield stress. In the craze growth regime, the presence of “grafted chain” sections of ≈100 monomers alters the mechanical response of composite samples, giving rise to smaller extension ratios and higher drawing stresses than for the homopolymer matrix. As a result, the dominant failure mechanism of composite samples depends strongly on the length of the grafted chains, with disentanglement being the dominant mechanism for short chains, while bond breaking is the failure mode for chain lengths >10N e , where N e is the entanglement length.

36 MATERIALS SCIENCE↗

Chemical structure and curing dynamics of bisphenol S, PEEK™-like, and resveratrol phthalonitrile thermoset resins

This effort provides a multifaceted analysis of the structural changes and material dynamics of thermally driven softening and curing of three distinct phthalonitrile (PN) resins that cross-link into thermally stable and oxidation-resistant thermosets. Although this material system has yielded a large subset of fire-retardant composites that require facile processing and low-temperature curing, to date, insufficient information had been available on the fundamental processes that drive their softening and curing stages. Our approach conducted a complementary analysis the chemistry, monomer mobility, and rheology of three PN polymers in order to correlate the curing processes with corresponding structural and behavioral transformations of thermosets. Here, we focused on PNs with a bisphenol S backbone, a bisphenol A (PEEK™-like) backbone, and a resveratrol backbone. We relied on quasi-elastic neutron scattering (QENS) in order to analyze the in situ dynamics and self-diffusion properties of PN monomers, and to track changes in their mobilities during cross-linking and staging. Our analysis facilitates proper control over the staging and final curing of these resins and enables more efficient processing of these thermosets.

36 MATERIALS SCIENCE↗

Enhancement of oxidation resistance of graphite foams by polymer derived-silicon carbide coating for concentrated solar power applications

Graphite foam with extremely high thermal conductivity has been investigated to enhance heat transfer of latent heat thermal energy storage (LHTES) systems. However, the use of graphite foam for elevated temperature applications (>600 °C) is limited due to poor oxidation resistance of graphite. In the present study, oxidation resistance of graphite foam coated with silicon carbide (SiC) was investigated. A pre-ceramic polymer derived coating (PDC) method was used to form a SiC coating on the graphite foams. Post coating deposition, the samples were analyzed by scanning electron microscopy and energy dispersive spectroscopy. The oxidation resistance of PDC-SiC coating was quantified by measuring the weight of the samples at several measuring points. The experiments were conducted under static argon atmosphere in a furnace. After the experiments, oxidation rates (%/hour) were calculated to predict the lifetime of the graphite foams. The experimental results showed that the PDC-SiC coating could prevent the oxidation of graphite foam under static argon atmosphere up to 900 °C.

36 MATERIALS SCIENCE↗

Hybrid tandem photovoltaic devices with a transparent conductive interconnecting recombination layer

Highlights: ► This work enhanced power conversion efficiency of the hybrid tandem solar cell from 1.0% to 2.6%. ► The interfacial series resistance of the tandem solar cell was eliminated by inserting ITO layer. ► This work shows the feasibility of the highly efficient hybrid tandem solar cells. -- Abstract: We demonstrate hybrid tandem photovoltaic devices with a transparent conductive interconnecting recombination layer. The series-connected hybrid tandem photovoltaic devices were developed by combining hydrogenated amorphous silicon (a-Si:H) and polymer-based organic photovoltaics (OPVs). In order to enhance the interfacial connection between the subcells, we employed highly transparent and conductive indium tin oxide (ITO) thin layer. By using the ITO interconnecting layer, the power conversion efficiency of the hybrid tandem solar cell was enhanced from 1.0% (V{sub OC} = 1.041 V, J{sub SC} = 2.97 mA/cm{sup 2}, FF = 32.3%) to 2.6% (V{sub OC} = 1.336 V, J{sub SC} = 4.65 mA/cm{sup 2}, FF = 41.98%) due to the eliminated interfacial series resistance.

36 MATERIALS SCIENCE↗

Alternative High Performance Polymers for Ablative Thermal Protection Systems

Ablative thermal protection systems are commonly used as protection from the intense heat during re-entry of a space vehicle and have been used successfully on many missions including Stardust and Mars Science Laboratory both of which used PICA - a phenolic based ablator. Historically, phenolic resin has served as the ablative polymer for many TPS systems. However, it has limitations in both processing and properties such as char yield, glass transition temperature and char stability. Therefore alternative high performance polymers are being considered including cyanate ester resin, polyimide, and polybenzoxazine. Thermal and mechanical properties of these resin systems were characterized and compared with phenolic resin.

Ablator↗

Giant magnetoelectric effect at low frequencies in polymer-based thin film composites

A polymer-based magnetoelectric 2-2 composite was fabricated in a thin film approach by direct spin coating of polyvinylidenefluoride-co-trifluoroethylene onto a Metglas substrate without the usage of an adhesive for the mechanical coupling between the piezoelectric and magnetostrictive materials. For a prototype single-sided clamped cantilever, a magnetoelectric coefficient as high as 850 V cm{sup −1} Oe{sup −1} is observed at its fundamental bending mode resonance frequency at 27.8 Hz and a detection limit of 10 pTHz{sup −1/2} at its second bending mode resonance frequency at 169.5 Hz.

36 MATERIALS SCIENCE↗

Preface - JES Focus Issue on Advances in Modern Polymer Electrolyte Fuel Cells in Honor of Shimshon Gottesfeld

The advances in polymer electrolyte fuel cell (PEFC) technologies over the past few decades and particularly over the past few years, have been very impressive. The promise of PEFC-based fuel cell electric vehicles (FCEVs) as long range EVs of zero emissions, high conversion efficiency, and fit for use of fuels from renewable sources, was recognized by pioneers of this technology some 40 years ago, facing at the time significant skepticism. The eventual commercial introduction of FCEVs in 2015 was enabled by the impressive accomplishments of scientists, engineers, and policymakers over that period of time. Among those responsible for the fuel cell community's success, few, if any, have had more impact than Dr. Shimshon Gottesfeld. He is a distinguished fuel cell educator, a passionate fuel cell and alternative fuel advocate, and a pioneering fuel cell innovator, responsible for several critical contributions that helped demonstrate the commercial viability of polymer electrolyte fuel cells. His impact on the field is seen through specific technical accomplishments, the scientists he has mentored, the teams he has led in different topical areas, and his activities as organizer and speaker in technical fuel cell meetings. We are honored to dedicate this focus issue of the Journal of The Electrochemical Society, entitled 'Advances in Modern Polymer Electrolyte Fuel Cells in Honor of Shimshon Gottesfeld,' to Dr. Gottesfeld for his accomplishments in the area of PEFC science and technology.

30 DIRECT ENERGY CONVERSION↗

Creation of Well-Defined “Mid-Sized” Micropores in Carbon Molecular Sieve Membranes

Carbon molecular sieve (CMS) membranes are choices for the separation of organic molecules due to their stability, ability to be scaled at practical form factors, and the avoidance of expensive supports or complex multi-step fabrication processes. A critical challenge is the creation of “mid-range” (e.g., 5–9 Å) microstructures that allow for facile permeation of organic solvents and selection between similarly-sized guest molecules. In this work, we create these microstructures via the pyrolysis of a microporous polymer (PIM-1) under low concentrations of hydrogen gas. The introduction of H 2 inhibits aromatization of the decomposing polymer and ultimately results in the creation of a well-defined bimodal pore network that exhibits an ultramicropore size of 5.1 Å. The H 2 assisted CMS dense membranes show a dramatic increase in p-xylene ideal permeability (≈15 times), with little loss in p-xylene/o-xylene selectivity (18.8 vs. 25.0) when compared to PIM-1 membranes pyrolyzed under a pure argon atmosphere. This method is successfully extended to hollow fiber membranes operating in organic solvent reverse osmosis mode, highlighting the potential of this approach to be translated from the laboratory to the field.

36 MATERIALS SCIENCE↗

Effects of ionomer morphology on oxygen reduction on Pt

In this paper, the oxygen reduction reaction (ORR) at the interface between platinum and Nafion 1100 equivalent weight was studied as a function of temperature (20–80 °C), humidity (10–100%), scan rate, the manner in which Nafion film was deposited, and the state of the Pt surface using ultramicroelectrodes employing cyclic voltammetry and chronoamperometry. ORR on smooth electrodes was strongly inhibited under specific conditions dependent on temperature, humidity, and scan rate. From the data presented, we postulate that dynamic changes in the molecular structure of the ionomer at the platinum interface result in differences in ORR voltammetry for films prepared and equilibrated under different conditions. The lack of similar changes for rough, platinized electrodes has been attributed to differences in initial ionomer structure and a higher energy barrier for ionomer restructuring. Finally, these model system studies yield insight into the ionomer-catalyst interface of particular interest for polymer electrolyte fuel cells.

14 SOLAR ENERGY↗

Large-Strain Time-Temperature Equivalence and Adiabatic Heating of Polyethylene

Time-temperature equivalence is a well-known phenomenon in time-dependent material response, where rapid events at a moderate temperature are indistinguishable from some occurring at modest rates but elevated temperatures. However, there is as-yet little elucidation of how well this equivalence holds for substantial plastic strains. In this work, we demonstrate time-temperature equivalence over a large range in a previously studied high-density polyethylene formulation (HDPE). At strain-rates exceeding 0.1/s, adiabatic heating confounds the comparison of nominally isothermal material response, apparently violating time-temperature equivalence. Strain-rate jumps can be employed to access the instantaneous true strain rate without heating. Adiabatic heating effects were isolated by comparing a locus of isothermal instantaneous flow stress measurements from strain-rate jumps up to 1/s with the predicted equivalent states at 0.01/s and 0.001/s in compression. Excellent agreement between the isothermal jump condition locus and the quasi-static tests was observed up to 50% strain, yielding one effective isothermal plastic response for each material for a given time-temperature equivalent state. These results imply that time-temperature equivalence can be effectively used to predict the deformation response of polymers during extreme mechanical events (large strain and high strain-rate) from measurements taken at reduced temperatures and nominal strain-rates in the laboratory.

36 MATERIALS SCIENCE↗

Modeling and simulation of soft-particle colloids under dynamic environmental gradients.

Controlled assembly in soft-particle colloidal suspensions is a technology poised to advance manufacturing methods for nano-scale templating, coating, and bio-conjugate devices. Applications for soft-particle colloids include photovoltaics, nanoelectronics, functionalized thin-film coatings, and a wide range of bio-conjugate devices such as sensors, assays, and bio-fuel cells. This presentation covers the topics of modeling and simulation of soft-particle colloidal systems over dewetting, evaporation, and irradiation gradients, including deposition of particles to surfaces. By tuning particle/solvent and environmental parameters, we transition from the regime of self-assembly to that of controlled assembly, and enable finer resolution of features at both the nano-scale and meso-scale. We report models of interparticle potentials and order parametrization techniques including results from simulations of colloids utilizing soft-particle field potentials. Using LAMMPS (Large-Scale Atomic/Molecular Massively Parallel Simulator), we demonstrate effects of volume fraction, shear and drag profiles, adsorbed and bulk polymer parameters, solvent chi parameter, and deposition profiles. Results are compared to theoretical models and correlation to TEM images from soft-particle irradiation experiments.

36 MATERIALS SCIENCE↗

Evaluating and predicting molecular mechanisms of adhesive degradation during field and accelerated aging of photovoltaic modules

Extending photovoltaic (PV) module lifetimes beyond 30 years is a goal of significant priority. A challenge that must first be addressed, however, is the development of a predictive reliability model that captures the synergy of terrestrial stressors on module degradation, particularly at encapsulant interfaces. Using a metrology designed specifically for PV modules, a comprehensive study of the widely used ethylene vinyl acetate encapsulant was performed in which encapsulant adhesion was evaluated as a function of environmental stressors (UV exposure, temperature, and humidity) for modules aged both under accelerated lab and internationally located field conditions for months to nearly 3 decades. Mechanical and chemical characterization methods are combined with fundamental polymer reaction engineering to unravel the degradation processes active at the molecular scale that lead to encapsulant delamination. An analytical and modular model framework is put forward enabling the prediction of long-term PV module durability, starting from fundamental principles at the molecular level and explicitly accounting for bond rupture events in the bulk encapsulant and at the encapsulant interfaces. Successful parameter tuning to adhesion data indicates a dominant occurrence of deacetylation, β-scission, and hydrolytic depolymerization, respectively. The model contributes to the longstanding challenge of predicting module lifetimes in any geographic location while minimizing time-consuming and costly aging studies.

14 SOLAR ENERGY↗

Rate-dependent phase transition of high density polyethylene

Quasi-static and dynamic tension tests are conducted on a widely used semicrystalline polymer, high density polyethylene (HDPE), to explore the strain rate effects on phase transition. HDPE exhibits considerable strain-rate hardening. In situ , high-speed x-ray diffraction demonstrates a martensitic transformation from the orthorhombic to monoclinic phase during both loading conditions. However, compared to quasi-static loading, the phase transition occurs at a lower bulk strain but higher stress under dynamic loading (strain rate 5100 s –1 ), suggesting strain-rate-accelerated phase transition dynamics. Furthermore, evolutions of lattice strain with bulk stress indicate different roles of amorphous and crystalline phases in deformation under different strain rates.

36 MATERIALS SCIENCE↗