Search NASA⌕ Search

SEARCH · Search NASA

Results for “ReACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Performance Evaluation and Analysis of Critical Interface Features of the National Compact Stellarator Experiment (NCSX)

The (18) modular coils for the National Compact Stellarator Experiment (NCSX) are joined at assembly by interfaces to form a toroidal shell which serves as the structural backbone of the device. There are six each of three coil types (A, B, and C); consequently, there are 4 distinct interface designs (A-A, A-B, B-C, C-C). This paper describes the performance evaluations and analyses used in the development of these critical interfaces. Initial analyses indicated that the baseline interface designs did not provide adequate shear capability along the inner (unbolted) legs between the modular coils and did not adequately address assembly tolerance requirements. Consequently a design effort was undertaken to develop interfaces with adequate shear capability and which would facilitate the achievement of assembly tolerances. Analyses indicated that a friction coefficient of 0.3 is necessary for 'no-slip' joints with a preload value of {approx}320 kN in the outboard regions. Two types of compatible segmented friction shims were developed to meet the friction requirement. One type uses alumina coated stainless steel shims and the other uses G-10/ stainless steel/ G-10 'sandwich shims.' Analyses indicated that the time constant requirements for induced currents in the shell could still be achieved with welds along all the inner (unbolted) legs except at the C-C interface. Consequently, welded interfaces utilizing alternating MIG fillet welds on each end of shims between coil castings were developed to react the shear loads. This configuration minimizes distortion since it avoids direct weld shrinkage stress across the interfaces. Analyses indicates that a 12.7 mm fillet weld has adequate shear capability, with average stress through the welds of 90-125 MPa, compared to a static limit of 217 MPa. Custom sized compression pucks located in the middle of the welded shims react the compressive loads and have average stresses less than 137 MPa. Fatigue acceptability of the welded joints - was examined using crack growth data of welded specimens and estimates the maximum acceptable initial flaw size in 12.7 mm welds to be 3.2 mm. At this size, a crack would propagate to an unacceptably large size in 500,000 (5 X life).

36 MATERIALS SCIENCE↗

Energy efficient synthesis of boranes

The reaction of halo-boron compounds (B--X compounds, compounds having one or more boron-halogen bonds) with silanes provides boranes (B--H compounds, compounds having one or more B--H bonds) and halosilanes. Inorganic hydrides, such as surface-bound silane hydrides (Si--H) react with B--X compounds to form B--H compounds and surface-bound halosilanes. The surface bound halosilanes are converted back to surface-bound silanes electrochemically. Halo-boron compounds react with stannanes (tin compounds having a Sn--H bond) to form boranes and halostannanes (tin compounds having a Sn--X bond). The halostannanes are converted back to stannanes electrochemically or by the thermolysis of Sn-formate compounds. When the halo-boron compound is BCl.sub.3, the B--H compound is B.sub.2H.sub.6, and where the reducing potential is provided electrochemically or by the thermolysis of formate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reduction of Oxyiron(V) by Sulfite and Thiosulfate in Aqueous Solution

The reduction of oxyiron(V), Fe{sup V}O{sub 4}{sup 3-} by inorganic oxysulfur species (SO{sub 3}{sup 2-} and S{sub 2}O{sub 3}{sup 2-}) has been studied anaerobically in alkaline medium by using a premix pulse radiolysis technique. Studies on the reactions of Fe{sup VI}O{sub 4}{sup 2-} with the two sulfur radicals were also carried out. The spectroscopic results demonstrated that sulfur radicals reduced Fe{sup VI}O{sub 4}{sup 2-} to Fe{sup V}O{sub 4}{sup 3-} which is subsequently reduced by oxysulfur species by a two-electron reduction step to Fe(III). The rate constants for reduction of Fe{sup VI}O{sub 4}{sup 2-} to Fe{sup V}O{sub 4}{sup 3-} by sulfite and thiosulfate radicals ({sm_bullet}SO{sub 3}{sup -} and S{sub 4}O{sub 6}{sup 3-}{sm_bullet}) were found to be (1.9 {+-} 0.3) x 10{sup 8} and (7.5 {+-} 0.8) x 10{sup 7} M{sup -1} s{sup -1}, respectively. However, the reactions of Fe{sup V}O{sub 4}{sup 3-} with the SO{sub 3}{sup 2-} and S{sub 2}O{sub 3}{sup 2-} ions were separated by an order of magnitude, with SO{sub 3}{sup 2-} reacting at (3.9 {+-} 0.3) x 10{sup 4} M{sup -1} s{sup -1} while S{sub 2}O{sub 3}{sup 2-} reacted with Fe(V) at (2.1 {+-} 0.1) x 10{sup 3} M{sup -1} s{sup -1} at pH 11.4.

54 ENVIRONMENTAL SCIENCES↗

Dispersoid reinforced alloy powder and method of making

A method of making dispersion-strengthened alloy particles involves melting an alloy having a corrosion and/or oxidation resistance-imparting alloying element, a dispersoid-forming element, and a matrix metal wherein the dispersoid-forming element exhibits a greater tendency to react with a reactive species acquired from an atomizing gas than does the alloying element. The melted alloy is atomized with the atomizing gas including the reactive species to form atomized particles so that the reactive species is (a) dissolved in solid solution to a depth below the surface of atomized particles and/or (b) reacted with the dispersoid-forming element to form dispersoids in the atomized particles to a depth below the surface of said atomized particles. The atomized alloy particles are solidified as solidified alloy particles or as a solidified deposit of alloy particles. Bodies made from the dispersion strengthened alloy particles, deposit thereof, exhibit enhanced fatigue and creep resistance and reduced wear as well as enhanced corrosion and/or oxidation resistance at high temperatures by virtue of the presence of the corrosion and/or oxidation resistance imparting alloying element in solid solution in the particle alloy matrix.

36 MATERIALS SCIENCE↗

Resilient Control System Execution Agent (ReCoSEA)

In an increasingly networked world, critical infrastructure systems suffer from two types of vulnerability. The first is the traditionally recognized problem of monitoring the systems for faults and failures, recognizing and analyzing data, and responding with real understanding to the problems of the system. Increasingly complex systems create the opportunity for single points of failure to cascade when inaccurate assessment of system health increases response time or leads to faulty analysis of the problems involved. A second problem involves vulnerability to cyber intrusion, in which bad actors can mask system deterioration or present false data about system status. A resilient system will protect stability, efficiency, and security. To ensure these three states, the system must react to changing conditions within the system with coordination: no one component of the system can be allowed to react to problems without real consideration of the effects of that action on other components within the system. Systems with multi-agent design typically have three layers of action, a management layer, a coordination layer, and an execution layer. A resilient multi-agent system will emphasize functions of the execution layer, which has the responsibility of initiating actions, monitoring, analyzing, and controlling its own processes, while feeding information back to the higher levels of management and coordination. The design concept of a resilient control system execution agent (ReCoSEA) grows out of these underpinnings, and through the use of computational intelligence techniques, this paper suggests an associated design methodology.

47 OTHER INSTRUMENTATION↗

Method of converting a polyol to an olefin

A method of preparing an olefin comprising: reacting a polyol in the presence of a carboxylic acid, such that an olefin is produced by the deoxygenation of the polyol. The reacting step can comprise (a) providing a composition comprising the polyol, (b) heating the composition, and (c) introducing the carboxylic acid to the composition wherein the introducing step occurs prior to, at the same time as, or subsequent to the heating step. In one embodiment, the polyol is glycerol, the carboxylic acid is formic acid, and the olefin is allyl alcohol, which is produced at a yield of about 80% or greater.

Bergman, Robert G↗

Methods of forming single source precursors, methods of forming polymeric single source precursors, and single source precursors and intermediate products formed by such methods

Methods of forming single source precursors (SSPs) include forming intermediate products having the empirical formula 1/2{L.sub.2N(.mu.-X).sub.2M'X.sub.2}.sub.2, and reacting MER with the intermediate products to form SSPs of the formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2, wherein L is a Lewis base, M is a Group IA atom, N is a Group IB atom, M' is a Group IIIB atom, each E is a Group VIB atom, each X is a Group VIIA atom or a nitrate group, and each R group is an alkyl, aryl, vinyl, (per)fluoro alkyl, (per)fluoro aryl, silane, or carbamato group. Methods of forming polymeric or copolymeric SSPs include reacting at least one of HE.sup.1R.sup.1E.sup.1H and MER with one or more substances having the empirical formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2 or L.sub.2N(.mu.-X).sub.2M'(X).sub.2 to form a polymeric or copolymeric SSP. New SSPs and intermediate products are formed by such methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fluorine compounds for doping conductive oxide thin films

Methods of forming a conductive fluorine-doped metal oxide layer on a substrate by chemical vapor deposition are described. The methods may include heating the substrate in a processing chamber, and introducing a metal-containing precursor and a fluorine-containing precursor to the processing chamber. The methods may also include adding an oxygen-containing precursor to the processing chamber. The precursors are reacted to deposit the fluorine-doped metal oxide layer on the substrate. Methods may also include forming the conductive fluorine-doped metal oxide layer by plasma-assisted chemical vapor deposition. These methods may include providing the substrate in a processing chamber, and introducing a metal-containing precursor, and a fluorine-containing precursor to the processing chamber. A plasma may be formed that includes species from the metal-containing precursor and the fluorine-containing precursor. The species may react to deposit the fluorine-doped metal oxide layer on the substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nano-structured polymer composites and process for preparing same

A process for preparing a polymer composite that includes reacting (a) a multi-functional monomer and (b) a block copolymer comprising (i) a first block and (ii) a second block that includes a functional group capable of reacting with the multi-functional monomer, to form a crosslinked, nano-structured, bi-continuous composite. The composite includes a continuous matrix phase and a second continuous phase comprising the first block of the block copolymer.

36 MATERIALS SCIENCE↗

Method for providing a low density high strength polyurethane foam

Disclosed is a method for making a polyurethane closed-cell foam material exhibiting a bulk density below 4 lbs/ft.sup.3 and high strength. The present embodiment uses the reaction product of a modified MDI and a sucrose/glycerine based polyether polyol resin wherein a small measured quantity of the polyol resin is "pre-reacted" with a larger quantity of the isocyanate in a defined ratio such that when the necessary remaining quantity of the polyol resin is added to the "pre-reacted" resin together with a tertiary amine catalyst and water as a blowing agent, the polymerization proceeds slowly enough to provide a stable foam body.

36 MATERIALS SCIENCE↗

Phosphazene additives

An additive comprising a phosphazene compound that has at least two reactive functional groups and at least one capping functional group bonded to phosphorus atoms of the phosphazene compound. One of the at least two reactive functional groups is configured to react with cellulose and the other of the at least two reactive functional groups is configured to react with a resin, such as an amine resin of a polycarboxylic acid resin. The at least one capping functional group is selected from the group consisting of a short chain ether group, an alkoxy group, or an aryloxy group. Also disclosed are an additive-resin admixture, a method of treating a wood product, and a wood product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocomposites for Underwater Deflagration

Nanometer aluminum fuel particles demonstrate orders of magnitude higher ignition sensitivity and reactivity than micrometer aluminum particles. This enhanced ignition sensitivity could enable a submerged reaction to propagate and react to completion without quenching. Energetic composites consisting of micrometer Al fuel particles cannot react submerged because too much energy from the reaction is lost to the surrounding water, causing the reactants to quench. However, Al nanoparticles can be synthesized with significantly higher surface-area-to-volume ratios that enable them to exhibit new and unique combustion properties that are much improved over their micron scale counterparts.

99 GENERAL AND MISCELLANEOUS↗

Cascade redox flow battery systems

A reduction/oxidation ("redox") flow battery system includes a series of electrochemical cells arranged in a cascade, whereby liquid electrolyte reacts in a first electrochemical cell (or group of cells) before being directed into a second cell (or group of cells) where it reacts before being directed to subsequent cells. The cascade includes 2 to n stages, each stage having one or more electrochemical cells. During a charge reaction, electrolyte entering a first stage will have a lower state-of-charge than electrolyte entering the nth stage. In some embodiments, cell components and/or characteristics may be configured based on a state-of-charge of electrolytes expected at each cascade stage. Such engineered cascades provide redox flow battery systems with higher energy efficiency over a broader range of current density than prior art arrangements.

25 ENERGY STORAGE↗

Methods of forming single source precursors, methods of forming polymeric single source precursors, and single source precursors formed by such methods

Methods of forming single source precursors (SSPs) include forming intermediate products having the empirical formula 1/2{L.sub.2N(.mu.-X).sub.2M'X.sub.2}.sub.2, and reacting MER with the intermediate products to form SSPs of the formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2, wherein L is a Lewis base, M is a Group IA atom, N is a Group IB atom, M' is a Group IIIB atom, each E is a Group VIB atom, each X is a Group VIIA atom or a nitrate group, and each R group is an alkyl, aryl, vinyl, (per)fluoro alkyl, (per)fluoro aryl, silane, or carbamato group. Methods of forming polymeric or copolymeric SSPs include reacting at least one of HE.sup.1R.sup.1E.sup.1H and MER with one or more substances having the empirical formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2 or L.sub.2N(.mu.-X).sub.2M'(X).sub.2 to form a polymeric or copolymeric SSP. New SSPs and intermediate products are formed by such methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Upgrading of petroleum oil feedstocks using alkali metals and hydrocarbons

A method of upgrading an oil feedstock by removing heteroatoms and/or one or more heavy metals from the oil feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase separable from the organic oil feedstock material. The upgradant hydrocarbon bonds to the oil feedstock material and increases the number of carbon atoms in the product. This increase in the number of carbon atoms of the product increases the energy value of the resulting oil feedstock.

02 PETROLEUM↗

Dispersoid reinforced alloy powder and method of making

A method of making dispersion-strengthened alloy particles involves melting an alloy having a corrosion and/or oxidation resistance-imparting alloying element, a dispersoid-forming element, and a matrix metal wherein the dispersoid-forming element exhibits a greater tendency to react with a reactive species acquired from an atomizing gas than does the alloying element. The melted alloy is atomized with the atomizing gas including the reactive species to form atomized particles so that the reactive species is (a) dissolved in solid solution to a depth below the surface of atomized particles and/or (b) reacted with the dispersoid-forming element to form dispersoids in the atomized particles to a depth below the surface of said atomized particles. Bodies made from the dispersion strengthened solidified particles exhibit enhanced fatigue and creep resistance and reduced wear as well as enhanced corrosion and/or oxidation resistance at high temperatures.

36 MATERIALS SCIENCE↗

Covalently functionalized carbon nanostructures and methods for their separation

The present invention is directed to carbon nanostructures, e.g., carbon nanotubes, methods of covalently functionalizing carbon nanostructures, and methods of separating and isolating covalently functionalized carbon. In some embodiments, carbon nanotubes are reacted with alkylating agents to provide water soluble covalently functionalized carbon nanotubes. In other embodiments, carbon nanotubes are reacted with a thermally-responsive agent and exposed to light in order to separate carbon nanotubes of a specific chirality from a mixture of carbon nanotubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dispersoid reinforced alloy powder and method of making

A method of making dispersion-strengthened alloy particles involves melting an alloy having a corrosion and/or oxidation resistance-imparting alloying element, a dispersoid-forming element, and a matrix metal wherein the dispersoid-forming element exhibits a greater tendency to react with a reactive species acquired from an atomizing gas than does the alloying element. The melted alloy is atomized with the atomizing gas including the reactive species to form atomized particles so that the reactive species is (a) dissolved in solid solution to a depth below the surface of atomized particles and/or (b) reacted with the dispersoid-forming element to form dispersoids in the atomized particles to a depth below the surface of said atomized particles. The atomized alloy particles are solidified as solidified alloy particles or as a solidified deposit of alloy particles. Bodies made from the dispersion strengthened alloy particles, deposit thereof, exhibit enhanced fatigue and creep resistance and reduced wear as well as enhanced corrosion and/or oxidation resistance at high temperatures by virtue of the presence of the corrosion and/or oxidation resistance imparting alloying element in solid solution in the particle alloy matrix.

36 MATERIALS SCIENCE↗