Search NASA⌕ Search

SEARCH · Search NASA

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Visualization of the flow about a delta wing maneuvering in pitch to very high angle of attack

An experimental program of unsteady aerodynamic measurements has been carried out in one of the 7 ft by 10 ft low-speed wind tunnels at NASA Ames Research Center. Flow-visualization measurements on a delta wing model of AR = 1.0 with sharp leading edges were carried out by means of a thin planar sheet of laser light fixed in the test section at a convenient angle to the flow direction. Smoke images of the fluid motion and vortex structure above the model were recorded photographically and later analyzed to determine such information as the positions of the cores and occurrence of bursting. Large amplitude transient motion involving post stall angle of attack excursions produced significant hysteresis in the vortex burst location and was reflected in the measured aerodynamic loads.

Jarrah, M. A. M.↗

Detection of False Data Injection Attacks in Battery Stacks Using Input Noise-Aware Nonlinear State Estimation and Cumulative Sum Algorithms

Grid-scale battery energy storage systems (BESSs) are vulnerable to false data injection attacks (FDIAs), which could be used to disrupt state of charge (SoC) estimation. Inaccurate SoC estimation has negative impacts on system availability, reliability, safety, and the cost of operation. In this article a combination of a Cumulative Sum (CUSUM) algorithm and an improved input noise-aware extended Kalman filter (INAEKF) is proposed for the detection and identification of FDIAs in the voltage and current sensors of a battery stack. The series-connected stack is represented by equivalent circuit models, the SoC is modeled with a charge reservoir model and the states are estimated using the INAEKF. Further, the root mean squared error of the states’ estimation by the modified INAEKF was found to be superior to the traditional EKF. By employing the INAEKF, this article addresses the research gap that many state estimators make asymmetrical assumptions about the noise corrupting the system. Additionally, the INAEKF estimates the input allowing for the identification of FDIA, which many alternative methods are unable to achieve. The proposed algorithm was able to detect attacks in the voltage and current sensors in 99.16% of test cases, with no false positives. Utilizing the INAEKF compared to the standard EKF allowed for the identification of FDIA in the input of the system in 98.43% of test cases.

25 ENERGY STORAGE↗

Modeling Interfaces to Support Low-Level Waste Disposal System Performance Assessments - 20366

In low-level waste (LLW) disposal sites, interfaces between cementitious materials, used as waste forms and/or engineered barriers, and the surrounding soil or backfill material are often encountered. Reactions across these interfaces may lead to chemical and structural alteration of the cementitious and backfill materials that may ultimately affect long-term performance. For example, the ingress of carbon dioxide from soil gas into a waste tank concrete shell at the Hanford Site or Savannah River Site (SRS) or a low-level waste disposal vault at SRS leads to carbonation of cement hydration products (e.g. portlandite, calcium-silicate hydrate or C-S-H, and ettringite). The result of carbonation is a decrease in pH in the cement paste portion of the tank wall or vault concrete structure that could ultimately lead to de-passivation of the embedded structural steel and, eventually, to cracking. Cracking can lead to increased ingress of water into the structure, corresponding increased release of constituents of concern, and to subsequent increased transport of these constituents to the surrounding environment. The mobility of trace constituents (e.g., radionuclides of concern) in waste forms may increase in response to changes in pH, pore structure, and mineralogical gradients. Depletion of portlandite results in subsequent decalcification of C-S-H that leads to changes in the cement strength and may lead to structural failure. At the boundary between waste forms and concrete vaults, the migration of sulfate ions from the salt waste form (e.g., the saltstone waste form used for LLW disposal at the Savannah River Site in Saltstone Disposal Units, or SDUs) into the barrier or vault concrete has been predicted to result in expansive mineral phase formation (or 'sulfate attack'). Expansive mineral formation could result in cracking and potential loss of structural integrity in the vault concrete. In the performance assessment (PA) for the SRS SDUs, prediction of both the carbonation and sulfate attack fronts are critical to assessing the long-term performance of these LLW disposal vaults. A general purpose geochemical reactive transport model has been developed in LeachXS/ORCHESTRA to evaluate typical interfaces for LLW disposal environments, including SDUs at SRS. The model may be used to predict the long-term performance of interfaces between cementitious materials and saltstone or backfill materials with respect to primary phases by considering mass transport, cement chemistry, geochemical speciation, and multi-ionic diffusion over interfaces between different materials. The present study compares the performance and interactions between vault concrete and saltstone waste form for a representative SDU scenario. The materials were characterized using pH-dependence leaching test (EPA 1313) and semi-dynamic transport tests (EPA 1315) with test results used to parameterize the interface model. The development of a credible inter model provides an important basis for supporting future PAs where carbonation and sulfate attack are important aging and degradation mechanisms. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Parameters influencing dynamic stability characteristics of Viking-type entry configurations at Mach 1.76.

Free-oscillation tests of three Viking-type blunt conical configurations were conducted in a wind tunnel to determine the important variables influencing their dynamic stability characteristics at Mach 1.76. The effects of sting geometry are shown to be significant at low angles of attack, while the effects of cross plane motions and tunnel vibration characteristics appear to be negligible. Variation of the reduced-frequency parameter and model base geometry caused significant effects in the data. An approximate technique was developed for converting effective data from either forced-oscillation or free-oscillation tests to values based on the instantaneous angle of attack.

Whitlock, C. H.↗

Heat-transfer tests on the Rockwell International space shuttle orbiter with and without simulated protuberances

Aerothermodynamic tests on the forward half of the Rockwell International Space Shuttle Orbiter Configuration 140C were conducted at Mach number 8. The phase-change paint and thin-skin thermocouple techniques were used to determine the aerodynamic heating rates on the Orbiter models during simulated atmospheric reentry. Smooth 0.04-scale models and models with scaled protuberances and indentations which simulated the windshields, cargo bay door hinges, vents, and thruster nozzles were tested over an angle-of-attack range from 20 to 45 deg at yaw angles from -5 to 5 deg and at Reynolds numbers, based on the total Orbiter scaled length, from 2.15 to 15.9 million. Comparisons of the model heat-transfer rates obtained with a smooth surface and with scaled protuberances are presented.

Carter, L. D.↗

Anomaly Detection for Power System Generation Control based on Hierarchical DBSCAN

The generation level of a generator in power grid is under control of multiple control loops such as governor action, Automatic Generation Control (AGC), and manual control. These control loops are vulnerable to cyber attacks and could become potential targets for the malicious adversary. In this paper, we investigated the detection of abnormal generation controls induced by cyber attacks. One data-driven anomaly detection methodology is presented based on the behavior conformity of generation units located in the same balancing authority. A semi-supervised clustering algorithm with Hierarchical Density based Spatial Clustering of Application with Noise (HDBSCAN) is proposed for the detection model training. In our previous work, we obtained a synthetic dataset that covers scenarios including normal operation, generation control under ramp attack, switching attack, AGC integrity attacks, etc. and it is used to evaluate the proposed clustering algorithm. Experimental results show that the proposed algorithm provides better detection accuracy than K-means clustering and can distinguish not only between normal and abnormal generation controls but also among various anomaly scenarios.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Effects of angle of attack and vertical fin on transonic flutter characteristics of an arrow-wing configuration

Experimental transonic flutter results are presented for a simplified 1/50 size, aspect ratio 1.77, wind tunnel model of an arrow wing design. Flutter results are presented for two configurations; namely, one with and one without a ventral fin mounted at the 0.694 semispan station. Results are presented for both configurations trimmed to zero lift and in a lifting condition at angles of attack up to 4 deg. The results show that the flutter characteristics of both configurations are similar to those usually observed. Increasing angle of attack reduces the flutter dynamic pressure by a small amount (about 13 percent maximum) for both configurations. The addition of the fin to the basic wing increases the flutter dynamic pressure. Calculated results for both configurations in the nonlifting condition obtained by using subsonic doublet lattice unsteady aerodynamic theory correlate reasonably well with the experimental results. Calculated results for the basic wing obtained by using subsonic kernal function unsteady aerodynamic theory did not agree as well with the experimental data.

Doggett, R. V., Jr.↗

Some Effects of Nose Bluntness and Fineness Ratio on the Static Longitudinal Aerodynamic Characteristics of Bodies of Revolution at Subsonic Speeds

. The effects of a systematic variation of nose shape and fineness ratio on the longitudinal aerodynamic characteristics of bodies of revolution have been qualitatively determined at subsonic speeds. Six nose shapes were investigated, representing five corner radii which varied from 0 to 50 percent of the body diameter and three face radii which varied from 50 percent of the model diameter to infinity. The complete models had fineness ratios of 0.50 to 2.00. In addition, effects of boattailing the afterbody and removing or varying the transitions trips which had been attached to initiate a turbulent boundary layer were noted. Results are presented for an angle-of-attack range from -4 deg to 24 deg for Mach numbers from 0.25 to 0.80, and indicate that small variations of the model nose can produce large variations in the static longitudinal aerodynamic characteristics of the body. These variations may in turn be moderated by an increase in the model fineness ratio .

Hayes, William C., Jr.↗

Aerothermodynamic measurements on a proposed assured crew return vehicle (ACRV) lifting-body configuration at Mach 6 and 10 in air

A 0.02-scale model of a lifting-body concept for possible application to the Assured Crew Return Vehicle from Space Station Freedom was tested at Mach 6 and 10 in air. Thermal mappings and surface streamline patterns were obtained at angles of attack ranging from 0 to 30 deg and unit Reynolds numbers Re from 2 to 8 x 10 to the 6th/ft. Areas that experienced the highest heating were near the model nose and tip-fin leading edges. The effect of Re on windward centerline heating coefficients was negligible, whereas increases in angles of attack produced increases in heating. At Mach 6 and the highest unit Re, turbulent heat at the windward centerline was three to four times the laminar level. Leeward crossflow separation and vortex reattachment along the centerline are evident across the Re and angle-of-attack ranges tested, indicative of a complex flowfield.

Horvath, Thomas J.↗

Drag characteristics of a disk-gap-band parachute with a nominal diameter of 1.65 meters at Mach numbers from 2.0 to 3.0

Supersonic wind-tunnel tests were conducted with disk-gap-band parachute models having a nominal diameter of 1.65 meters and geometric porosities of 10.0, 12.5, and 15.0 percent. Canopy inflation characteristics, angles of attack, and drag performance are presented for deployment behind forebody base extensions which were free to oscillate in pitch and yaw. The effect of increasing suspension-line length on canopy motions and drag performance is included, and the drag performance of a model with 12.5 percent geometric porosity is compared with results from flight tests of a parachute with a nominal diameter of 12.19 meters.

Mayhue, R. J.↗

Turbulence Model Comparisons for a High-Speed Aircraft

Four turbulence models are described and evaluated for transonic flows over the High-Speed Research/industry baseline configuration known as Reference H by using the thin-layer, upwind, Navier-Stokes solver known as CFL3D. The turbulence models studied are the equilibrium model of Baldwin-Lomax (B-L) with the Degani-Schiff (D-S) modifications, the one-equation Baldwin-Barth (B-B) model, the one-equation Spalart-Allmaras (S-A) model, and Menter's two-equation Shear Stress Transport (SST) model. The flow conditions, which correspond to tests performed in the National Transonic Facility (NTF) at Langley Research Center, are a Mach number of 0.90 and a Reynolds number of 30 x 10 (exp. 6) based on mean aerodynamic chord for angles of attack of 1 deg., 5 deg., and 10 deg. The effects of grid topology and the representation of the actual wind tunnel model geometry are also investigated. Computed forces and surface pressures compare reasonably well with the experimental data for all four turbulence models.

Rivers, Melissa B.↗

Transition Prediction for the 30P30N Airfoil and the CRM-HL using FUN3D

The ability to accurately model transition over high-lift configurations can lead to improved agreement between stationary Reynolds-Averaged Navier-Stokes (RANS) computations and experimental measurements. In this work, selected transport-equation-based RANS models for transition prediction in the NASA FUN3D flow solver are used to simulate flow over the 30P30N three-element airfoil and the High-Lift Common Research Model (CRM-HL). The primary RANS-based transition model is the Langtry-Menter (LM) 𝜸-Re𝜽𝒕 model coupled with the Menter shear-stress transport model. Additionally, the existing capability for transition prediction based on linear stability correlations is used to allow the modeling of transition over multiple elements of the 30P30N configuration. This approach pairs an algebraic transition model with the Spalart-Allmaras (SA) turbulence model that relies on an imposed transition location in FUN3D and the parabolized stability equations as implemented in the LASTRAC code. Predictions based on these different transition prediction approaches and models are compared with each other, experimental data, and previous simulations by evaluating the lift and drag coefficients, the surface-pressure/skin-friction distributions, and the locations of transition onset. Results are presented for multiple angles of attack for the 30P30N airfoil and CRM-HL. For the CRM-HL, a grid resolution study is performed for the LM transition model and the SA turbulence model.

High Lift↗

Use of the updated NASA Langley radio-controlled drop-model technique for high-alpha studies of the X-29A configuration

This paper presents an overview of the radio-controlled drop-model technique used for low-speed flight dynamics research at the NASA Langley Research Center. The overall test methodology is reviewed and the major elements of the system are discussed including model construction and equipment, the closed-loop control system, and the flight test facility. To illustrate the capabilities of the technique, selected results from an ongoing program to study the high-angle-of-attack flight dynamics of the X-29A configuration are reviewed. Three research areas are highlighted: motion prediction, control system effects, and motion analysis and modeling. Finally, several current upgrades to the overall technique are discussed along with the enhanced test capability that they will provide.

Fratello, David J.↗

Development of Defenses against False Data Injection Attacks for Nuclear Power Plants

With the recent successful attempts against the digital control systems of critical infrastructures, there is a need to develop new defense strategies that recognize two important realities, 1) state- sponsored attackers can rely on a number of techniques including espionage, social engineering, and brute force techniques, etc. to gain access to the raw data used to control system behavior, 2) attackers can falsify operational data in manners that do not trigger conventional outlier/anomaly detection techniques in order to go undetected, which is referred to as false data injection attacks. Therefore, there is a strong need to explore another class of defense measures, referred to as physical process defense, serving as a new line of defense in the event existing defenses relying on information protection measures are breached. This physical process defenses utilize the physics and engineering models of the system to build unique signatures for genuine system behavior. If successful, the signatures would be able to detect attacks that falsify the operational data and render them harmless before they can inflict physical damage on the system. This report is focused on exploring the feasibility of physical process defenses for nuclear reactors, and their associated functional requirements to maximize their resiliency against state-sponsored, or equivalent, attackers.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Forward rotor vortex effects on counter rotating propeller noise

Three configurations of a model counter rotating propeller manipulate the blade tip flow by: placing the CRP at angle of attack, installing shrouds, and turning the upstream blades to provide forward sweep. Flow visualization and flow measurements with thermal anemometry show no evidence of a tip vortex; however, a leading edge vortex was detected on aft swept blades. The modifications served to alter the strength and/or path of the leading edge vortex. The vortical flow is eliminated by forward sweep on the upstream propeller blades. Far field acoustic data from each test indicate only small influences on the level and directivity of the BPFs. The interaction tone at the sum of the two BPF's was significantly altered in a consistent manner. As the vortex system varied, the interaction tone was affected: far field noise levels in the forward quandrant increased and the characteristic noise minimum near the plane of rotation became less pronounced and in some cases were eliminated. If the forward propeller leading edge vortex system does not impact the rear propeller in the standard manner, a net increase in the primary interaction tone occurs for the model tested. If the leading edge vortex is removed, the interaction tone increases.

Laur, Michele↗

DPW-VI Results Using FUN3D with Focus on k-kL-MEAH2015 (k-kL) Turbulence Model

The Common Research Model wing-body configuration is investigated with the k-kL-MEAH2015 turbulence model implemented in FUN3D. This includes results presented at the Sixth Drag Prediction Workshop and additional results generated after the workshop with a nonlinear Quadratic Constitutive Relation (QCR) variant of the same turbulence model. The workshop provided grids are used, and a uniform grid refinement study is performed at the design condition. A large variation between results with and without a reconstruction limiter is exhibited on "medium" grid sizes, indicating that the medium grid size is too coarse for drawing conclusions in comparison with experiment. This variation is reduced with grid refinement. At a fixed angle of attack near design conditions, the QCR variant yielded decreased lift and drag compared with the linear eddy-viscosity model by an amount that was approximately constant with grid refinement. The k-kL-MEAH2015 turbulence model produced wing root junction flow behavior consistent with wind tunnel observations.

Abdol-Hamid, K. S.↗

An aerodynamic model for one and two degree of freedom wing rock of slender delta wings

The unsteady aerodynamic effects due to the separated flow around slender delta wings in motion were analyzed. By combining the unsteady flow field solution with the rigid body Euler equations of motion, self-induced wing rock motion is simulated. The aerodynamic model successfully captures the qualitative characteristics of wing rock observed in experiments. For the one degree of freedom in roll case, the model is used to look into the mechanisms of wing rock and to investigate the effects of various parameters, like angle of attack, yaw angle, displacement of the separation point, and wing inertia. To investigate the roll and yaw coupling for the delta wing, an additional degree of freedom is added. However, no limit cycle was observed in the two degree of freedom case. Nonetheless, the model can be used to apply various control laws to actively control wing rock using, for example, the displacement of the leading edge vortex separation point by inboard span wise blowing.

Hong, John↗