Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Visualization, understanding, and mitigation of process-induced-membrane irregularities in gas diffusion electrode-based polymer electrolyte membrane fuel cells

Polymer electrolyte membrane fuel cells (PEMFC) show substantial promise for their application in electric vehicles. For large-scale manufacturing of PEMFCs, roll-to-roll coated gas-diffusion-electrodes (GDE) offer certain advantages over other production pathways. Procedures including hot pressing and coating an ionomer overlayer may be necessary for this manufacturing pathway to enable a suitable catalyst layer/membrane interface. The same procedures may potentially introduce membrane irregularities, especially when thin membranes are used. Limited understanding exists regarding if and to what extent such irregularities impact PEMFC performance and lifetime, and therefore be considered defects. In this study, NREL's customized fuel cell hardware that enables quasi in-situ infrared (IR) thermography studies was utilized to visualize spatial hydrogen crossover and identify membrane irregularities that originated from the GDE-based MEA fabrication process. The structure of these membrane irregularities was investigated by scanning electron microscopy (SEM) and its impact on initial H2/air performance was determined. Accelerated stress testing (AST) revealed that these irregularities develop into failure point locations. These results were validated across many MEAs with identified process-induced membrane irregularities. By selecting specific gas diffusion media properties and by fine tuning the MEA hot pressing parameters, the formation of such membrane irregularities was mitigated.

08 HYDROGEN↗

Using θ' interfaces as templates for planar L1 2 precipitation in AlCuMnZr alloys

Controlled Mn and Zr additions to Al-Cu alloys have allowed for the improved retention of mechanical properties after extended 350°C exposures by stabilizing the main strengthening θ' (Al 2 Cu) phase. Ultimately, θ'/L1 2 (Al 3 Zr) co-precipitate formation stabilizes θ' most effectively; however, Zr diffuses sluggishly and has low solubility in aluminum castings. Increasing the Zr segregation rate would allow for faster and more effective θ'/L1 2 co-precipitation. It is demonstrated that the Zr segregation rate is faster when the Zr matrix content is higher. A much higher Zr matrix content was achieved by rapid cooling during additive manufacturing (AM) that produces θ'/L1 2 co-precipitation faster, which is shown by scanning transmission electron microscopy and atom probe tomography experiments. It was also found that Zr continuously segregates to θ' interfaces up to the most aggressive heat treatment studied such that planar L1 2 precipitates remain after the metastable θ' dissolves. In this manner, we demonstrate that θ' coherent interfaces serve as perfect templates to form stable planar L1 2 precipitates that can provide strength at higher temperatures than traditional θ' strengthened AlCu alloys. This work introduces an alloy design strategy that uses metastable precipitates to quickly nucleate and grow co-precipitates with a desired geometry that contain slow diffusing elements. These ideas can be applied to engineer more heat resistant alloys by taking advantage of high solute matrix contents enabled by rapid cooling during additive manufacturing.

36 MATERIALS SCIENCE↗

Consistent Multigroup Theory Enabling Accurate Course-Group Simulation of Gen-IV Reactors

The objective of this proposal is the development of a consistent multi-group theory that accurately accounts for the energy-angle coupling associated with collapsed-group cross sections. This will allow for coarse-group transport and diffusion theory calculations that exhibit continuous energy accuracy and implicitly treat cross- section resonances. This is of particular importance when considering the highly heterogeneous and optically thin reactor designs within the Next Generation Nuclear Plant (NGNP) framework. In such reactors, ignoring the influence of anisotropy in the angular flux on the collapsed cross section, especially at the interface between core and reflector near which control rods are located, results in inaccurate estimates of the rod worth, a serious safety concern. The scope of this project will include the development and verification of a new multi-group theory enabling high-fidelity transport and diffusion calculations in coarse groups, as well as a methodology for the implementation of this method in existing codes. This will allow for a higher accuracy solution of reactor problems while using fewer groups and will reduce the computational expense. The proposed research represents a fundamental advancement in the understanding and improvement of multi- group theory for reactor analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Bilayer Structure and Lipid Dynamics in a Model Stratum Corneum with Oleic Acid

The stratum corneum is the uppermost layer of the skin and acts as a barrier to keep out contaminants and retain moisture. Understanding the molecular structure and behavior of this layer will provide guidance for optimizing its biological function. In this study we use a model mixture comprised of equimolar portions of ceramide NS (24:0), lignoceric acid, and cholesterol to model the effect of the addition of small amounts of oleic acid to the bilayer at 300 and 340 K. Five systems at each temperature have been simulated with concentrations between 0 and 0.1 mol % oleic acid. Our major finding is that subdiffusive behavior over the 200 ns time scale is evident in systems at 340 K, with cholesterol diffusion being enhanced with increased oleic acid. Importantly, cholesterol and other species diffuse faster when radial densities indicate nearest neighbors include more cholesterol. We also find that, with the addition of oleic acid, the bilayer midplane and interfacial densities are reduced and there is a 3% decrease in total thickness occurring mostly near the hydrophilic interface at 300 K with reduced overall density at 340 K. Increased interdigitation occurs independent of oleic acid with a temperature increase. Slight ordering of the long non-hydroxy fatty acid of the ceramide occurs near the hydrophilic interface as a function of the oleic acid concentration, but no significant impact on hydrogen bonding is seen in the chosen oleic acid concentrations.

08 HYDROGEN↗

Ionic Liquid-Enhanced Interfaces to Boost Reactive C O2 Capture

The addition of ionic liquids (ILs) to a mixture containing a molecular solvent and other ionic species can induce the heterogeneous redistribution of cations and anions at the gas–liquid interface. This nonuniform redistribution of cations and anions driven by the differences in the solvophilicity of ions can improve the thermophysical and interfacial properties of such mixtures, creating a local chemical environment that is conducive to some reactions. In this work, ILs are added to a mixture of potassium hydroxide (KOH) and ethylene glycol (EG), used as a reactive absorbent and electrolyte in the migration-assisted moisture-gradient (MAMG) process for CO 2 capture. Molecular dynamics (MD) simulations are employed to probe into the effects of complex ion–ion and ion–solvent interactions and to examine the chemical composition at the gas–liquid interface. A total of 12 systems are investigated using molecular simulations to identify trends in the performance of IL additives based on the choice of cation, anion, and IL concentration. The cation effects are studied using IL additives based on 1-ethyl-3-methylimidazolium ([EMIM] + ) and 1-butyl-3-methylimidazolium ([BMIM] + ), while the impact of anions is examined using additives based on dicyanamide [DCA] − , triflate [TfO] − , bistriflimide [NTf 2 ] − , and hexafluorophosphate [PF 6 ] − anions, respectively. The influence of the IL concentration is also evaluated at molar concentrations between 1% and 4%. The simulation results indicate that the use of IL additives can affect the physical CO 2 solubility, surface tension, and the localization of CO 2 around the [OH] − ions at the gas–liquid interface. It is also evident that the choice of cations, anions, and IL concentration determines the extent to which the IL additives impact the local physicochemical properties. Physical dissolution, diffusive transport, and interaction with [OH] − are critical intermediate steps toward reactive CO 2 capture using a liquid absorbent. Hence, the improvement in one or more of these properties, aided by IL additives, is expected to improve the overall CO 2 capture performance. Experiments reaffirmed the impact of IL additives on CO 2 capture performance and the sensitivity to the choice of the cation, anion, and concentration of the IL additive.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Field Testing of an Unvented Roof with Fibrous Insulation, Tiles and Vapor Diffusion Venting

This research is a test implementation of an unvented tile roof assembly in a hot-humid climate (Orlando, FL; Zone 2A), insulated with air permeable insulation (netted and blown fiberglass). Given the localized moisture accumulation and failures seen in previous unvented roof field work, it was theorized that a 'diffusion vent' (water vapor open, but air barrier 'closed') at the highest points in the roof assembly might allow for the wintertime release of moisture, to safe levels. The 'diffusion vent' is an open slot at the ridge and hips, covered with a water-resistant but vapor open (500+ perm) air barrier membrane. As a control comparison, one portion of the roof was constructed as a typical unvented roof (self-adhered membrane at ridge). The data collected to date indicate that the diffusion vent roof shows greater moisture safety than the conventional, unvented roof design. The unvented roof had extended winter periods of 95-100% RH, and wafer (wood surrogate RH sensor) measurements indicating possible condensation; high moisture levels were concentrated at the roof ridge. In contrast, the diffusion vent roofs had drier conditions, with most peak MCs (sheathing) below 20%. In the spring, as outdoor temperatures warmed, all roofs dried well into the safe range (10% MC or less). Some roof-wall interfaces showed moderately high MCs; this might be due to moisture accumulation at the highest point in the lower attic, and/or shading of the roof by the adjacent second story. Monitoring will be continued at least through spring 2016 (another winter and spring).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Growth of ordered silver nanoparticles in silica film mesostructured with a triblock copolymer PEO-PPO-PEO

Elaboration of mesostructured silica films with a triblock copolymer polyethylene oxide-polypropylene oxide-polyethylene oxide, (PEO-PPO-PEO) and controlled growth of silver nanoparticles in the mesostructure are described. The films are characterized using UV-visible optical absorption spectroscopy, TEM, AFM, SEM, X-ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS). Organized arrays of spherical silver nanoparticles with diameter between 5 and 8 nm have been obtained by NaBH{sub 4} reduction. The size and the repartition of silver nanoparticles are controlled by the film mesostructure. The localization of silver nanoparticles exclusively in the upper-side part of the silica-block copolymer film is evidenced by RBS experiment. On the other hand, by using a thermal method, 40 nm long silver sticks can be obtained, by diffusion and coalescence of spherical particles in the silica-block copolymer layer. In this case, migration of silver particles toward the glass substrate-film interface is shown by the RBS experiment. - Graphical abstract: Growth of silver nanoparticles in a mesostructured block copolymer F127-silica film is performed either by a chemical route involving NaBH{sub 4} reduction or by a thermal method. An array of spherical silver nanoparticles with 10 nm diameter on the upper-side of the mesostructured film or silver sticks long of 40 nm with a preferential orientation are obtained according to the method used. a: TEM image of the Fag5SiNB sample illustrating the silver nanoparticles array obtained by the chemical process; b: HR-TEM image of the Fag20Sid2 sample illustrating the silver nanosticks obtained by the thermal process.

36 MATERIALS SCIENCE↗

Direct observation of interfacial reaction of Ni/6H-SiC and carbon redistribution by in situ transmission electron microscopy

Highlights: • Interfacial reaction mechanism for Ni/SiC at 550 °C is investigated in situ by TEM. • NBED, EDS and EELS analyses were performed to identify the phases formed. • Carbon atoms from decomposed SiC were redistributed in three different regions. • Graphite/Ni{sub 31}Si{sub 12}/Ni{sub 31}Si{sub 12} + graphite/6H-SiC structure was observed after the reaction. - Abstract: The interfacial reaction of Ni/SiC has been attracting considerable attention because SiC substrate has excellent chemical and thermal stability and low electrical resistivity, which are essential properties for various device applications. However, research on the initial reaction at low temperature and exact mechanism is currently insufficient. Therefore, we investigated the reaction of Ni films on a 6H-SiC substrate and the behavior of carbon at 550 °C by direct observation with transmission electron microscopy (TEM) during in situ heating. At 550 °C, the Ni{sub 31}Si{sub 12} phase formed during the reaction of Ni and SiC. The Ni silicide layer thickened as the reaction front proceeded toward the 6H-SiC substrate and carbon atoms from decomposed SiC converted into graphite. In addition, carbon existed in three regions. First, carbon existed as graphite on the external surface of Ni silicide layer during initial reaction. Second, graphite formed at the original interface between the Ni film and the 6H-SiC substrate. Finally, carbon existed at the bottom of the Ni silicide region due to its low diffusivity in the silicide. The elemental distribution of Ni, Si, and C was observed in detail through various analytical techniques. We demonstrate the reaction mechanism of Ni and SiC at 550 °C and the distribution of carbon atoms.

36 MATERIALS SCIENCE↗

Facile fabrication of micro-floriated AgBr/Bi{sub 2}O{sub 3} as highly efficient visible-light photocatalyst

Highlights: • We successfully fabricate micro-floriated AgBr/Bi{sub 2}O{sub 3} composites by one simple hydrothermal react with precusor BiOBr. This micro-floriated Bi{sub 2}O{sub 3} heterojunction composite is rarely reported by others. • Heterojunction AgBr/Bi{sub 2}O{sub 3} composite exhibits highly efficient photocatalytic activity to decompose pollutant. • The enhanced photocatalytic activity was attributed to the improved visible light harvesting ability and higher separation efficiency of photogenerated electron–hole pairs by the introduction of AgBr. • This composite is beneficial to industrial applications to eliminate the organic pollutants from waste water. - Abstract: Semiconductor with photocatalytic property is the potential solution to solve the problem about water pollution. Novel floriated AgBr/Bi{sub 2}O{sub 3} fabricated through a facile simple two-step hydrothermal method is an efficient photocatalyst. The eminent performance for degradation of methyl orange (MO) was evaluated under visible light irradiation. Many characterization methods, including XPS, XRD, FT-IR, SEM, TEM and UV–vis diffuse reflection spectroscopy, were used to investigate the structure, elemental composition, morphology and catalytic activity. Broad contact between AgBr and Bi{sub 2}O{sub 3} interface enabled hybrid materials possess superior efficiency for the decomposition of MO under visible light irradiation. The optimum photocatalytic activity of samples was approximately 11.7 times higher than pure Bi{sub 2}O{sub 3}. In addition, the photo-generated reactive species were identified based on free radicals trapping experiments, which revealed that superoxide radical is the key factor to the photocatalytic process.

36 MATERIALS SCIENCE↗

In Situ Visualization of the Pinning Effect of Planar Defects on Li Ion Insertion

Longevity of Li ion batteries strongly depends on the interaction of transporting Li ions in electrode crystals with defects. However, detailed interactions between the Li ion flux and structural defects in the host crystal remain obscure due to the transient nature of such interactions. Here, by in situ transmission electron microscopy and density function theory calculations, we reveal how the diffusion pathways and transport kinetics of a Li ion can be affected by planar defects in a tungsten trioxide lattice. We uncover that changes in charge distribution and lattice spacing along the planar defects disrupt the continuity of ion conduction channels and dramatically increase the energy barrier of Li diffusion, thus, arresting Li ions at the defect sites and twisting the lithiation front. In conclusion, the atomic-scale understanding holds critical implications for rational interface design in solid-state batteries and solid oxide fuel cells.

25 ENERGY STORAGE↗

Molecular design for growth of supramolecular membranes with hierarchical structure

Membranes with hierarchical structure exist in biological systems, and bio-inspired building blocks have been used to grow synthetic analogues in the laboratory through self-assembly. The formation of these synthetic membranes is initiated at the interface of two aqueous solutions, one containing cationic peptide amphiphiles (PA) and the other containing the anionic biopolymer hyaluronic acid (HA). The membrane growth process starts within milliseconds of interface formation and continues over much longer timescales to generate robust membranes with supramolecular PA–HA nanofibers oriented orthogonal to the interface. Computer simulation indicates that formation of these hierarchically structured membranes requires strong interactions between molecular components at early time points in order to generate a diffusion barrier between both solutions. Experimental studies using structurally designed PAs confirm simulation results by showing that only PAs with high ζ potential are able to yield hierarchically structured membranes. Furthermore, the chemical structure of such PAs must incorporate residues that form β-sheets, which facilitates self-assembly of long nanofibers. In contrast, PAs that form low aspect ratio nanostructures interact weakly with HA and yield membranes that exhibit non-fibrous fingering protrusions. Furthermore, experimental results show that increasing HA molecular weight decreases the growth rate of orthogonal nanofibers. Overall, this result is supported by simulation results suggesting that the thickness of the interfacial contact layer generated immediately after initiation of self-assembly increases with polymer molecular weight.

36 MATERIALS SCIENCE↗

Light driven microflow in ice

We optically pump water through micrometer thin ice sheets. The ice is locally moved with speeds exceeding 5 cm/s by repetitive melting and freezing, which occurs around a moving infrared laser spot. The minimal channel width is 10 {mu}m. The diffusion limitation of ice allows for fast spatial biomolecule control without predefined channels, valves, or external pumps. Dye molecules are pumped across an ice-ice interface, showing the possibility of microfluidic applications. Pumping in ice is three orders of magnitude faster than the previously shown for thermoviscous pumping in water.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Less can be more: Insights on the role of electrode microstructure in redox flow batteries from two-dimensional direct numerical simulations

Understanding how to structure a porous electrode to facilitate fluid, mass, and charge transport is key to enhancing the performance of electrochemical devices, such as fuel cells, electrolyzers, and redox flow batteries (RFBs). Here, using a parallel computational framework, direct numerical simulations are carried out on idealized porous electrode microstructures for RFBs. Strategies to improve an electrode design starting from a regular lattice are explored. By introducing vacancies in the ordered arrangement, it is possible to achieve higher voltage efficiency at a given current density, thanks to improved mixing of reactive species, despite reducing the total reactive surface. Careful engineering of the location of vacancies, resulting in a density gradient, outperforms disordered configurations. Our simulation framework is a new tool to explore transport phenomena in RFBs, and our findings suggest new ways to design performant electrodes.

25 ENERGY STORAGE↗

Thermally excited capillary waves at vapor/liquid interfaces of water-alcohol mixtures

The density profiles of liquid/vapor interfaces of water–alcohol (methanol, ethanol and propanol) mixtures were studied by surface-sensitive synchrotron x-ray scattering techniques. X-ray reflectivity and diffuse scattering measurements, from the pure and mixed liquids, were analyzed in the framework of capillary wave theory to address the characteristic length scales of the intrinsic roughness and the shortest capillary wavelength (alternatively, the upper wavevector cutoff in capillary wave theory). Our results establish that the intrinsic roughness is dominated by average interatomic distances. The extracted effective upper wavevector cutoff indicates capillary wave theory breaks down at distances of the order of bulk correlation lengths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

GeSn alloys with ∼21% Sn grown by effusion cell molecular beam epitaxy

We report the epitaxial growth of high quality GeSn alloys with Sn compositions up to 21.25 ± 1% by effusion-cell molecular beam epitaxy (MBE). Achieving such a high Sn content with effusion cells is particularly significant, since these sources typically impose stronger radiative heating on the substrate, which is a factor long considered a major obstacle to high-Sn GeSn epitaxy. Contrary to the prevailing assumption that high growth rates are good for suppressing Sn segregation, we demonstrate that carefully controlled low fluxes, combined with stable ultra-low substrate temperatures, enable significant Sn incorporation even under effusion-cell conditions. Structural analyses by high-resolution x-ray diffraction, reciprocal space mapping, atomic force microscopy, and transmission electron microscopy confirm sharp interfaces, high crystallinity, and smooth surfaces at high Sn contents. Furthermore, these findings establish the feasibility of MBE-grown high-Sn GeSn even under diffusion cells, thereby broadening opportunities for Si-compatible photonic and quantum devices.

Alloys↗

Computer Simulation of Proton Transport in Fuel Cell Membranes (Final Report)

This DOE-supported research grant focused on understanding the nature of proton transport in complex systems such as proton exchange membranes (PEMs). The most unique aspect of the research was the development and implementation of a novel multiscale reactive molecular dynamics (MS-RMD) methodology. In this approach, covalent bonds can dynamically break and form, allowing one to accurately treat the proton hopping process essential to capturing the physics of proton transport. The Voth group applied this method to proton exchange membrane systems, providing insight into their proton transport mechanism. They found that protons can diffuse most rapidly in the water-rich regions, but that protons actually spend so little time in such regions that transport along the hydrophobic – hydrophilic interface controls the membrane performance. In addition, the group worked to increase understanding of acidic solutions, developing methods for simulating and interpreting experimental infrared vibrational spectroscopy for excess protons (acidic solutions). The group also implemented novel tools for developing proton transport reactive MD models using a relative entropy minimization scheme.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-scale modeling of wastage layer formation in metallic fuel cladding

Fuel-cladding chemical interaction (FCCI) is a major concern for U-Zr metallic fuels' performance, primarily due to the formation of a brittle layer (wastage) in the cladding. This brittle layer, resulting from intermetallic compounds between cladding constituents Fe, Cr, and lanthanide fission products, significantly impacts the cladding's mechanical integrity. Recent efforts focus on developing a mechanistic modeling framework to understand lanthanide production, transport to the fuel-cladding interface, and phase transformation to intermetallic phases. A multi-scale computational approach has been used to calculate lanthanide transport rates, with atomistic calculations determining Nd diffusivities through the solid fuel matrix and along pore surfaces. These diffusivities inform a mesoscale model to determine an effective diffusion coefficient, accounting for porosity and infiltration with bond sodium. This effective diffusivity is used in engineering-scale simulations via the BISON fuel performance code, which has been validated against EBR-II and FFTF reactor experiments.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Probing the effect of electron acceptor structure and morphology on charge separation in ZnO/P3HT hybrid photovoltaics using steady-state transient photoinduced absorption.

Hybrid cells based on ZnO/P3HT heterojunctions have the advantage of better device stability, but suffer poor photovoltaic performance compared to all-organic cells which use PCBM as the electron acceptor. The photovoltaic effect in these hybrid systems is accomplished via photoinduced charge separation at the interface between the absorbing polymer (P3HT) and the electron acceptor (ZnO). Efforts to improve device performance in these hybrid systems have centered on reducing the required diffusion length for P3HT excitons by creating bulk heterojunctions from either ZnO nanoparticles and P3HT or using ZnO precursors which convert in situ to form ZnO networks inside a polymer matrix. In this study, we use transient photoinduced absorption to access the lifetimes of P3HT polarons and excitons in bulk heterojunctions constructed using P3HT and ZnO nanoparticles or ZnO precursors and compare to those in planar ZnO/P3HT devices. Steady-state photoinduced absorption spectra of ZnO/P3HT show characteristic of sub-bandgap transitions associated with the formation of long-lived (msec lifetimes) radical cations (polarons) in P3HT. Similar short-lived polarons (psec lifetimes) are observed by picosecond transient photoinduced absorption in addition to infrared absorption due to excitons. Here we examine the lifetimes of both the excitons and polarons in ZnO:P3HT bulk heterojunctions using both picosecond and millisecond techniques in an effort to understand the effect of the structure and morphology of the electron acceptor on charge separation. We will also compare the relative photoexitation lifetimes, hence charge separation efficiency, for the planar and bulk heterojunction hybrid system to an all-organic P3HT:PCBM system.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗