Search NASA⌕ Search

SEARCH · Search NASA

Results for “material processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Optoelectronic and material properties of solution-processed Earth-abundant Cu 2 BaSn(S, Se) 4 films for solar cell applications

Copper barium thioselenostannate, Cu 2 BaSnS 4-x Se x (CBTSSe), absorbers employ low-toxicity and abundant metals while offering low-cost manufacturing options, controllable stoichiometry and band gap tunability (from 2 eV at x = 0 to 1.55 eV at x = 3). CBTSSe can therefore be considered a prospective candidate for maintaining or improving upon the advantages of already commercialized Cu(In,Ga)(S,Se) 2 (CIGSSe) and CdTe absorbers. Here, we focus on solution-deposited stoichiometric CBTSSe films with band gap of 1.59 eV (x ≈ 3) and explore the fundamental film properties. Temperature- and excitation-dependent photoluminescence studies reveal a dominant defect emission at ~1.5 eV and a second deep defect feature at 1.15 eV. From time-resolved terahertz measurements, we find a charge carrier (electron and hole sum) mobility of ~140 cm 2 /Vs—i.e., comparable to values in CIGSSe or Cu 2 ZnSnS 4-x Se x (CZTSSe)—as well as a two-component minority carrier lifetime. A longer-lived lifetime component (~2 ns) arises from bulk recombination. However, strong recombination at the (bare) surface leads to a ~50 ps lifetime, inferior to state-of-the-art CIGSSe or CZTSSe absorbers. This recombination issue may worsen for CBTSSe/CdS interfaces, due to a cliff-like band alignment with 0.6 eV band offset, as revealed by ultraviolet photoemission spectroscopy. A low number of charge carriers within the absorber further contributes to a high series resistance. Employing these films, we also report the highest performance achieved from solution-processed trigonal CBTSSe thin-film photovoltaic devices, with open circuit voltage, short-circuit current density, fill factor and efficiency of 470 mV, 14.3 mA/cm 2 , 43.6% and 2.9%, respectively. The physical measurements provided on the stoichiometric solution-processed CBTSSe absorber further point to critical areas for future improvement of CBTSSe and related photovoltaic cells in the quest for higher efficiency devices based on earth abundant metals.

14 SOLAR ENERGY↗

Tailored glycolysis of Nylon 6 to enable upcycling into high-strength adhesives

Nylon is a high-strength polyamide widely used in automotive, textiles, packaging, etc. However, its durability makes nylon waste difficult to manage, with recycling limited to mechanical grinding to make fillers. Here, we report a catalytic glycolysis approach to deconstruct Nylon 6 into controlled-length oligomers, enabling upcycling into value-added materials. A low-molecular-weight oligomer (M n = 1.8 kg/mol) was repolymerized with diepoxy-terminated poly(bisphenol A-co-epichlorohydrin) via mechanochemistry to create a high-performance adhesive. This copolymer achieves lap shear strengths over 22 MPa on steel and bonds steel to carbon fiber composites, nearly tripling the performance of commercial adhesives even at 90°C. Thermomechanical analyses show that the adhesive retains thermal stability similar to nylon 6 but melts at lower temperatures, allowing easier processing. The material can be reprocessed and reused without significant performance loss. This study demonstrates a strategy to convert nylon 6 waste into valuable materials, offering a sustainable path for difficult-to-recycle plastics.

Nylon waste↗

A cost-benefit analysis of landfill mining and material recycling in China

Highlights: • Assessing the economic feasibility of landfill mining. • We applied a cost-benefit analysis model for landfill mining. • Four material cycling and energy recovery scenarios were designed. • We used net present value to evaluate the cost-benefit efficiency. - Abstract: Landfill mining is an environmentally-friendly technology that combines the concepts of material recycling and sustainable waste management, and it has received a great deal of worldwide attention because of its significant environmental and economic potential in material recycling, energy recovery, land reclamation and pollution prevention. This work applied a cost-benefit analysis model for assessing the economic feasibility, which is important for promoting landfill mining. The model includes eight indicators of costs and nine indicators of benefits. Four landfill mining scenarios were designed and analyzed based on field data. The economic feasibility of landfill mining was then evaluated by the indicator of net present value (NPV). According to our case study of a typical old landfill mining project in China (Yingchun landfill), rental of excavation and hauling equipment, waste processing and material transportation were the top three costs of landfill mining, accounting for 88.2% of the total cost, and the average cost per unit of stored waste was 12.7 USD ton{sup −1}. The top three benefits of landfill mining were electricity generation by incineration, land reclamation and recycling soil-like materials. The NPV analysis of the four different scenarios indicated that the Yingchun landfill mining project could obtain a net positive benefit varying from 1.92 million USD to 16.63 million USD. However, the NPV was sensitive to the mode of land reuse, the availability of energy recovery facilities and the possibility of obtaining financial support by avoiding post-closure care.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Automated calculation and convergence of defect transport tensors

Defect diffusion is a key process in materials science and catalysis, but as migration mechanisms are often too complex to enumerate a priori, calculation of transport tensors typically have no measure of convergence and require significant end-user intervention. These two bottlenecks prevent high-throughput implementations essential to propagate model-form uncertainty from interatomic interactions to predictive simulations. In order to address these issues, we extend a massively parallel accelerated sampling scheme, autonomously controlled by Bayesian estimators of statewide sampling completeness, to build atomistic kinetic Monte Carlo models on a state-space irreducible under exchange and space group symmetries. Focusing on isolated defects, we derive analytic expressions for drift and diffusion coefficients, providing a convergence metric by calculating the Kullback–Leibler divergence across the ensemble of diffusion processes consistent with the sampling uncertainty. The autonomy and efficacy of the method is demonstrated on surface trimers in tungsten and Hexa-interstitials in magnesium oxide, both of which exhibit complex, correlated migration mechanisms.

36 MATERIALS SCIENCE↗

Bayesian characterization and forward propagation of the uncertainty in thermodynamic models for redox active materials

Demonstrating the thermodynamic efficiency of hydrogen conversion processes using various materials is a critical step in developing new technologies for storing concentrated solar energy, and is largely accomplished by using a thermodynamic model derived from experimental data. A main goal of this project is to calculate the uncertainty of the thermodynamic efficiency by calculating the uncertainty of the components that feed into the efficiency. Many different models and data sets were used to test the workflow. First, the models were fit to the data using a Bayesian Inference and a method called Markov Chain Monte Carlo (MCMC), which found the maximum a priori parameters, and a posterior probability distribution of the parameters. Next, the different models were compared to each other using model evidence values. It was found that for cleaner data sets, overfitting had not yet been reached, and the most complicated model was ideal, but on the noisier data sets, the less complex models were favored because the more complicated models resulted in overfitting. Next, forward propagation was used to calculate the enthalpy change and its associated uncertainty. A few variations on the models were tried, such as fitting in a different variable, producing negligible or negative effects on the fits of the models. Thus, the original models were used. A sensitivity analysis was performed, and used to calculate the model error. On the cleaner data sets, there was very minimal experimental noise, and thus, all resulting error was from the model. With consideration of the model error, the models fit the data very well, and the simpler model had a high model error, as expected. All these components will then be used to calculate the thermodynamic efficiency of the different materials.

14 SOLAR ENERGY↗

Laboratory Directed Research and Development Annual Report for 2009

This report documents progress made on all LDRD-funded projects during fiscal year 2009. As a US Department of Energy (DOE) Office of Science (SC) national laboratory, Pacific Northwest National Laboratory (PNNL) has an enduring mission to bring molecular and environmental sciences and engineering strengths to bear on DOE missions and national needs. Their vision is to be recognized worldwide and valued nationally for leadership in accelerating the discovery and deployment of solutions to challenges in energy, national security, and the environment. To achieve this mission and vision, they provide distinctive, world-leading science and technology in: (1) the design and scalable synthesis of materials and chemicals; (2) climate change science and emissions management; (3) efficient and secure electricity management from generation to end use; and (4) signature discovery and exploitation for threat detection and reduction. PNNL leadership also extends to operating EMSL: the Environmental Molecular Sciences Laboratory, a national scientific user facility dedicated to providing itnegrated experimental and computational resources for discovery and technological innovation in the environmental molecular sciences.

36 MATERIALS SCIENCE↗

Materials for Consideration in Standardized Canister Design Activities.

This document identifies materials and material mitigation processes that might be used in new designs for standardized canisters for storage, transportation, and disposal of spent nuclear fuel. It also addresses potential corrosion issues with existing dual-purpose canisters (DPCs) that could be addressed in new canister designs. The major potential corrosion risk during storage is stress corrosion cracking of the weld regions on the 304 SS/316 SS canister shell due to deliquescence of chloride salts on the surface. Two approaches are proposed to alleviate this potential risk. First, the existing canister materials (304 and 316 SS) could be used, but the welds mitigated to relieve residual stresses and/or sensitization. Alternatively, more corrosion-resistant steels such as super-austenitic or duplex stainless steels, could be used. Experimental testing is needed to verify that these alternatives would successfully reduce the risk of stress corrosion cracking during fuel storage. For disposal in a geologic repository, the canister will be enclosed in a corrosion-resistant or corrosion-allowance overpack that will provide barrier capability and mechanical strength. The canister shell will no longer have a barrier function and its containment integrity can be ignored. The basket and neutron absorbers within the canister have the important role of limiting the possibility of post-closure criticality. The time period for corrosion is much longer in the post-closure period, and one major unanswered question is whether the basket materials will corrode slowly enough to maintain structural integrity for at least 10,000 years. Whereas there is extensive literature on stainless steels, this evaluation recommends testing of 304 and 316 SS, and more corrosion-resistant steels such as super-austenitic, duplex, and super-duplex stainless steels, at repository-relevant physical and chemical conditions. Both general and localized corrosion testing methods would be used to establish corrosion rates and component lifetimes. Finally, it is unlikely that the aluminum-based neutron absorber materials that are commonly used in existing DPCs would survive for 10,000 years in disposal environments, because the aluminum will act as a sacrificial anode for the steel. We recommend additional testing of borated and Gd-bearing stainless steels, to establish general and localized corrosion resistance in repository-relevant environmental conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Damage by radicals and photons during plasma cleaning of porous low-k SiOCH. I. Ar/O{sub 2} and He/H{sub 2} plasmas

Porous dielectric materials offer lower capacitances that reduce RC time delays in integrated circuits. Typical porous low dielectric (low-k) materials include SiOCH-silicon dioxide with carbon groups, principally -CH{sub 3}, lining the pores. Fluorocarbon plasmas are often used to etch such low-k materials. These processes leave a fluorocarbon polymer on the SiOCH surface that must be removed, often with oxygen or hydrogen containing plasmas. Pores open to the surface and that are internally connected provide pathways for reactive species to enter into the porous network and produce damage. For example, during cleaning using O{sub 2} containing plasmas, reactions of O atoms with -CH{sub 3} groups can increase the k-value by removing C atoms. Vacuum ultraviolet (VUV) photons produced by the plasma and that penetrate into the material can scission -Si-CH{sub 3} bonds and accelerate the removal of -CH{sub 3} groups. This paper reports on results from a computational investigation of Ar/O{sub 2} and He/H{sub 2} plasma cleaning of porous SiOCH when including the effects of VUV photons. The authors found that He/H{sub 2} plasmas are able to clean CF{sub x} polymers deposited during etching while producing milder damage to underlying -CH{sub 3} sites compared to O{sub 2} plasmas due to the lower reactivity of H atoms and the shorter penetration distance of photons produced in He/H{sub 2} plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Engineering-Scale Demonstration of DuraLith and Ceramicrete Waste Forms

To support the selection of a waste form for the liquid secondary wastes from the Hanford Waste Immobilization and Treatment Plant, Washington River Protection Solutions (WRPS) has initiated secondary waste form testing on four candidate waste forms. Two of the candidate waste forms have not been developed to scale as the more mature waste forms. This work describes engineering-scale demonstrations conducted on Ceramicrete and DuraLith candidate waste forms. Both candidate waste forms were successfully demonstrated at an engineering scale. A preliminary conceptual design could be prepared for full-scale production of the candidate waste forms. However, both waste forms are still too immature to support a detailed design. Formulations for each candidate waste form need to be developed so that the material has a longer working time after mixing the liquid and solid constituents together. Formulations optimized based on previous lab studies did not have sufficient working time to support large-scale testing. The engineering-scale testing was successfully completed using modified formulations. Further lab development and parametric studies are needed to optimize formulations with adequate working time and assess the effects of changes in raw materials and process parameters on the final product performance. Studies on effects of mixing intensity on the initial set time of the waste forms are also needed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Oxy-Combustion Boiler Material Development

Under U.S. Department of Energy Cooperative Agreement No. DE-NT0005262 Foster Wheeler North America Corp conducted a laboratory test program to determine the effect of oxy-combustion on boiler tube corrosion. In this program, CFD modeling was used to predict the gas compositions that will exist throughout and along the walls of air-fired and oxy-fired boilers operating with low to high sulfur coals. Test coupons of boiler tube materials were coated with deposits representative of those coals and exposed to the CFD predicted flue gases for up to 1000 hours. The tests were conducted in electric tube furnaces using oxy-combustion and air-fired flue gases synthesized from pressurized cylinders. Following exposure, the test coupons were evaluated to determine the total metal wastage experienced under air and oxy-combustions conditions and materials recommendations were made. Similar to air-fired operation, oxy-combustion corrosion rates were found to vary with the boiler material, test temperature, deposit composition, and gas composition. Despite this, comparison of air-fired and oxy-fired corrosion rates showed that oxy-firing rates were, for the most part, similar to, if not lower than those of air-firing; this finding applied to the seven furnace waterwall materials (wrought and weld overlay) and the ten superheater/reheater materials (wrought and weld overlay) that were tested. The results of the laboratory oxy-combustion tests, which are based on a maximum bulk flue gas SO 2 level of 3200 ppmv (wet) / 4050 ppmv (dry), suggest that, from a corrosion standpoint, the materials used in conventional subcritical and supercritical, air-fired boilers should also be suitable for oxy-combustion retrofits. Although the laboratory test results are encouraging, they are only the first step of a material evaluation process and it is recommended that follow-on corrosion tests be conducted in coal-fired boilers operating under oxy-combustion to provide longer term (one to two year) data. The test program details and data are presented herein.

20 FOSSIL-FUELED POWER PLANTS↗

Porous Permeable SHS Cermets Based on Iron and Aluminum Oxides

Optimal batch composition is developed for porous permeable SHS cermets that may be used in processing smokestack gases at factories and also auto exhaust emissions. The physicomechanical properties of the cermets are determined when different batch compositions are employed. The permissible range of vibrational frequencies when such cermets are used as filters is determined.

36 MATERIALS SCIENCE↗

Phenomena-based graph representations and applications to chemical process simulation

Rapid and robust simulation of chemical processes is critical to conduct process design, optimization, techno-economic analysis, and sustainability analysis. Yet, efficiently solving simulation models remains a challenge due to the highly coupled and nonlinear nature of the underlying algebraic equations that capture the physical phenomena taking place in the process (e.g., material and energy conservation, phase equilibrium, reactions). In this work, we show that graph-theoretic representations of the physical phenomena within unit operations can help navigate and decompose equations to systematically identify alternative approaches for fast and robust numerical solutions. Specifically, we present a graph-theoretic abstraction that captures the connectivity between the model variables/equations and use this abstraction to group variables/equations into fundamental phenomena. We show that phenomena-based decomposition of the underlying equations can help decouple nonlinearities and enforce material/energy conservation at the process level to accelerate convergence. The proposed decomposition approach differs from the more traditional sequential modular simulation approach, in which equations are grouped and decomposed by unit operations. We implemented the phenomena-based decomposition in BioSTEAM—an open-source process simulation platform in Python—and demonstrated that this approach can converge a variety of separation process models. Compared to sequential modular simulation, the phenomena-based approach can converge idealized systems faster, but it can be slower for (or even fail to converge) highly coupled and nonideal process systems.

Convergence↗

Competition between deformability and charge transport in semiconducting polymers for flexible and stretchable electronics

The primary goal of the field concerned with organic semiconductors is to produce devices with performance approaching that of silicon electronics, but with the deformability—flexibility and stretchability—of conventional plastics. However, an inherent competition between deformability and charge transport has long been observed in these materials, and achieving the extreme (or even moderate) deformability implied by the word “plastic” concurrently with high charge transport may be elusive. This competition arises because the properties needed for high carrier mobilities—e.g., rigid chains in π-conjugated polymers and high degrees of crystallinity in the solid state—are antithetical to deformability. On the device scale, this competition can lead to low-performance yet mechanically robust devices, or high-performance devices that fail catastrophically (e.g., cracking, cohesive failure, and delamination) under strain. There are, however, some observations that contradict the notion of the mutual exclusivity of electronic and mechanical performances. These observations suggest that this problem may not be a fundamental trade-off, but rather an inconvenience that may be negotiated by a logical selection of materials and processing conditions. For example, the selection of the poly(3-alkylthiophene) with a critical side-chain length—poly(3-heptylthiophene) (n = 7)—marries the high deformability of poly(3-octylthiophene) (n = 8) with the high electronic performance (as manifested in photovoltaic efficiency) of poly(3-hexylthiophene) (n = 6). This review explores the relationship between deformability and charge transport in organic semiconductors. The principal conclusions are that reducing the competition between these two parameters is in fact possible, with two demonstrated routes being: (1) incorporation of softer, insulating material into a stiffer, semiconducting material and (2) increasing disorder in a highly ordered film, but not enough to disrupt charge transport pathways. The aim of this review is to provide a bridge between the fields interested in electronic properties and mechanical properties of conjugated polymers. We provide a high-level introduction to some of the important electronic and mechanical properties and measurement techniques for organic electronic devices, demonstrate an apparent competition between good electronic performance and mechanical deformability, and highlight potential strategies for overcoming this undesirable competition. A marriage of these two fields would allow for rational design of materials for applications requiring large-area, low-cost, printable devices that are ultra-flexible or stretchable, such as organic photovoltaic devices and wearable, conformable, or implantable sensors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Plastic Parallel Pathways Platform- 4P Model

The U.S. generates 42 million metric tons of plastic waste each year - the most of any country - of which less than 9% is recycled. This represents an estimated loss of $2.3 billion and 3.4 EJ embodied energy per year. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. Various recycling and waste management options are available for plastics, such as conversion into energy (incineration, pyrolysis, gasification), conversion to lower- or higher-grade plastics (mechanical recycling, chemical or enzymatic depolymerization processes, dissolution) or up-cycling to feedstock chemicals (photo/electro/catalytic methods, pyrolysis, gasification). While many previous publications have investigated a subset of these options, there is currently no modelling platform that can quantitatively assess and compare the economic and environmental impacts of all these different plastic management pathways and their respective products simultaneously. To directly compare the benefits and disadvantages of plastic-to-x technologies, we propose a novel analysis framework: the Plastic Parallel Pathways Platform (4P). 4P will model a systems analysis framework for capturing plastic material flows processed via different waste management scenarios. The total economic cost and greenhouse gas emissions (as well as additional economic, energetic, and environmental metrics indicators) of a given scenario will be calculated enabling comparison to other scenarios, thereby informing decisions on plastic recycling pathways.

circular economy↗

Continuous ultra-thin MoS{sub 2} films grown by low-temperature physical vapor deposition

Uniform growth of pristine two dimensional (2D) materials over large areas at lower temperatures without sacrifice of their unique physical properties is a critical pre-requisite for seamless integration of next-generation van der Waals heterostructures into functional devices. This Letter describes a vapor phase growth technique for precisely controlled synthesis of continuous, uniform molecular layers of MoS{sub 2} on silicon dioxide and highly oriented pyrolitic graphite substrates of over several square centimeters at 350 °C. Synthesis of few-layer MoS{sub 2} in this ultra-high vacuum physical vapor deposition process yields materials with key optical and electronic properties identical to exfoliated layers. The films are composed of nano-scale domains with strong chemical binding between domain boundaries, allowing lift-off from the substrate and electronic transport measurements from contacts with separation on the order of centimeters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Use of Carbon Steel for Construction of Post-combustion CO 2 Capture Facilities: A Pilot-Scale Corrosion Study

Corrosion studies were carried out on metal coated and noncoated carbon steel as well as stainless steel in a pilot-scale post-combustion CO 2 capture process. Aqueous 30 wt % monoethanolamine (MEA) solvent was used without any chemical additive for antioxidation to examine a worst-case scenario where corrosion is not mitigated. The corrosion rate of all carbon steels was almost zero in the absorber column and CO 2 lean amine piping except for Ni-coated carbon steel (<1.8 mm/yr). Ni 2 Al 3 /Al 2 O 3 precoated carbon steels showed initial protection but lost their integrity in the stripping column and CO 2 rich amine piping, and severe corrosion was eventually observed for all carbon steels at these two locations. Stainless steel was found to be stable and corrosion resistant in all of the sampling locations throughout the experiment. This study provides an initial framework for the use of carbon steel as a potential construction material for process units with relatively mild operating conditions (temperature less than 80 °C), such as the absorber and CO 2 lean amine piping of a post-combustion CO 2 capture process. As a result, it also warrants further investigation of using carbon steel with more effective corrosion mitigation strategies for process units where harsh environments are expected (such as temperatures greater than 100 °C).

36 MATERIALS SCIENCE↗

Collection strategy, inner morphology, and size distribution of dust particles in ASDEX Upgrade

The dust collection and analysis strategy in ASDEX Upgrade (AUG) is described. During five consecutive operation campaigns (2007–2011), Si collectors were installed, which were supported by filtered vacuum sampling and collection with adhesive tapes in 2009. The outer and inner morphology (e.g. shape) and elemental composition of the collected particles were analysed by scanning electron microscopy. The majority of the ~50?000 analysed particles on the Si collectors of campaign 2009 contain tungsten—the plasma-facing material in AUG—and show basically two different types of outer appearance: spheroids and irregularly shaped particles. By far most of the W-dominated spheroids consist of a solid W core, i.e. solidified W droplets. A part of these particles is coated with a low-Z material; a process that seems to happen presumably in the far scrape-off layer plasma. In addition, some conglomerates of B, C and W appear as spherical particles after their contact with plasma. By far most of the particles classified as B-, C- and W-dominated irregularly shaped particles consist of the same conglomerate with varying fraction of embedded W in the B–C matrix and some porosity, which can exceed 50%. The fragile structures of many conglomerates confirm the absence of intensive plasma contact. Both the ablation and mobilization of conglomerate material and the production of W droplets are proposed to be triggered by arcing. The size distribution of each dust particle class is best described by a log-normal distribution allowing an extrapolation of the dust volume and surface area. The maximum in this distribution is observed above the resolution limit of 0.28 µm only for the W-dominated spheroids, at around 1 µm. The amount of W-containing dust is extrapolated to be less than 300 mg on the horizontal areas of AUG.

99 GENERAL AND MISCELLANEOUS↗