Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Room Temperature Adsorptive Removal of Thiophene over Zinc Oxide-Based Adsorbents

This study investigated the room temperature adsorptive removal of thiophene over zinc oxide adsorbents in the presence of hydrogen. The bulk zinc oxide was prepared by precipitation method and calcined at different temperatures in the range of 300-550 °C. Supported zinc oxide was prepared by co-precipitation of 30 wt.% ZnO with alumina and calcined at 550 °C. Properties of the adsorbents were determined by various characterization techniques such as surface area and pore volume analysis, XRD, FESEM, EDX and TPR. The desulfurization process was carried out in a down-flow packed bed reactor at room temperature (30 °C). The BET surface area of bulk zinc oxide adsorbents decreased with the increase in calcination temperature from 300 to 550 °C. The surface area of bulk zinc oxide adsorbents was 30.5 and 14.6 m{sup 2}/g when calcined at 300 and 550 °C, respectively. The surface are of supported zinc oxide adsorbents was 177 m{sup 2}/g. The highest average pore size was obtained for bulk ZnO calcined at 550 °C (45 nm) compared to that calcined at 300 °C (42 nm) and supported ZnO (27 nm). The XRD peaks corresponded to the hexagonal structure of zinc oxide. The removal of thiophene was most significant for bulk ZnO calcined at 550 °C. The higher removal efficiency for this adsorbent in spite of lower surface area may be attributed to its higher percentage of larger pores and higher average pore size.

36 MATERIALS SCIENCE↗

Response surface modeling of CO 2 dynamic storage efficiency factor in high permeability thick sandstones

In order to utilize as much of the pore space for CO 2 storage in high permeability thick saline aquifers, it is vital to investigate the interactions of injected CO 2 with formation brine and rock. In order to quantify the displacement process, we investigate the dynamic storage efficiency factor (DSEF) for saline aquifers where pressure increase is minimal during the injection phase. Dimensionless numbers are derived from basic governing equations, constitutive equations, initial and boundary conditions using the inspection analysis. Then using the Hammersley sequence sampling, 178 numerical experiments are designed, and a compositional reservoir simulator is used to perform these simulations. In the next step, response surface regression analysis is used to establish a relationship between DSEF obtained from the numerical simulations and the corresponding dimensionless numbers. The simulation results show that for the studied conditions the underground dynamics is mostly influenced by the gravity number, followed by effective aspect ratio and dip numbers. The results from the response surface regression analysis are used to develop a correlation, which can be used to estimate the dynamic CO 2 storage capacity of relevant zones. This study provides quantitative measures for the different competing mechanisms involved in underground displacement of fluids in CO 2 geological storage, which can serve as a useful tool during planning phase of storage projects.

02 PETROLEUM↗

Structure-dependent localized surface plasmon resonance characteristics and surface enhanced Raman scattering performances of quasi-periodic nanoarrays: Measurements and analysis

A set of periodic and quasi-periodic Au nanoarrays with different morphologies have been fabricated by using electron beam lithography technique, and their optical properties have been examined experimentally and analyzed theoretically by scanning near-field optical microscope and finite element method, respectively. Results present that the localized surface plasmon resonance of the as-prepared Au nanoarrays exhibit the structure-depended characteristics. Comparing with the periodic nanoarrays, the quasi-periodic ones demonstrate stronger electric field enhancement, especially for Thue-Morse nanoarray. Meanwhile, the surface enhanced Raman scattering (SERS) spectra of 4-mercaptobenzoic acid molecular labeled nanoarrays show that the quasi-periodic nanoarrays exhibit distinct SERS enhancement, for example, a higher enhancement factor of ∼10{sup 7} is obtained for the Thue-Morse nanoarray consisted of square pillars of 100 nm size. Therefore, it is significant to optimally design and fabricate the chip-scale quasi-periodic nanoarrays with high localized electric field enhancement for SERS applications in biosensing field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interlaboratory Reproducibility of Contour Method Data Analysis and Residual Stress Calculation

While the contour method for residual stress assessment has developed rapidly, no published study documents its interlaboratory reproducibility. Objective: Here we report an initial reproducibility experiment focused on contour method data analysis and residual stress calculation. The experiment uses surface topography data from a physical process simulation of elastic-plastic beam bending. The simulation provides surface topography, for input to the contour method data analysis, as well as a known residual stress field with 130 MPa peak magnitude. Additionally, to increase realism, noise and specific artifacts are added to the topography data. A group of participants received the topography data (without the known residual stress), independently analyzed the data, and submitted results as a two-dimensional residual stress field. Analysis of submissions provides a group average residual stress field and the spatial distribution of reproducibility standard deviation. The group average residual stress agrees with the known stress in magnitude and spatial trend. The reproducibility standard deviation ranges from 2 to 54 MPa over the measurement plane, with an average of 5.4 MPa. Reproducibility standard deviation is smaller in the cross-section interior (≤ 5 MPa), modest near local extrema in the stress field (5 to 10 MPa), and larger near the cross-section boundaries (10 to 30 MPa). Overall, the largest values of reproducibility standard deviation (up to 54 MPa) occur in limited areas where artifacts had been added to the topography data; while some participants identified and removed these artifacts, some did not, leading to systematic differences that elevated the standard deviation.

42 ENGINEERING↗

Exploring Approaches for Accelerated Mass Spectrometric Detection of Fluorochemicals from Aqueous Solutions Using Indirect, Adsorbent-Facilitated Desorption Ionization

There is a growing need for rapid, low-cost analytical tools to screen water supplies for persistent contaminants. Due to their ubiquitous presence in the environment and their detrimental effects on human health, there is a public interest in widespread testing for perfluoroalkyl substances (PFAS). However, the most common methods for PFAS analysis can be time-intensive, requiring a preconcentration step followed by liquid chromatography–mass spectrometry (LC–MS), and are cost-prohibitive for most members of the public. To address these challenges, this study explores a novel method for rapid analysis of aqueous analytes by concentrating analytes on solid adsorbents and detecting them using mass spectrometric analysis via desorption ionization directly from the adsorbent surface. We demonstrate this general approach of indirect solution analysis (ISA) with desorption electrospray ionization (ISA-DESI) and laser desorption ionization (ISA-LDI). Various adsorbent materials were screened, including commercial mesoporous carbons, alumina, and metal–organic frameworks (MOFs). Using ISA-DESI, we consistently detect concentrations as low as 5–100 parts per trillion (ppt) for perfluorooctanoic acid (PFOA) and 10–100 ppt for perfluoroundecanoic acid (PFUnDA). This approach enables rapid detection in under 5 min, making it suitable for applications requiring trace detection with fast response times. We further demonstrate the use of ISA-DESI on a range of environmentally relevant contaminants. Advantages of this indirect solution analysis approach include simplified sample preparation, accelerated analysis, and low cost with readily available materials, making it a promising tool to accelerate mass spectrometric PFAS detection for identifying contaminated sites, performing laboratory studies, and monitoring industrial waste streams.

Bays, Nathan Robert [Sandia National Laboratories ↗

Weak Anti-localization and Quantum Oscillations of Surface States in Topological Insulator Bi2Se2Te

Topological insulators, a new quantum state of matter, create exciting opportunities for studying topological quantum physics and for exploring spintronic applications due to their gapless helical metallic surface states. Here, we report the observation of weak anti-localization and quantum oscillations originated from surface states in Bi2Se2Te crystals. Angle-resolved photoemission spectroscopy measurements on cleaved Bi2Se2Te crystals show a well-defined linear dispersion without intersection of the conduction band. The measured weak anti-localization effect agrees well with the Hikami-Larkin-Nagaoka model and the extracted phase coherent length shows a power-law dependence with temperature (lw,T20.44), indicating the presence of the surface states. More importantly, the analysis of a Landau-level fan diagram of Shubnikov-de Hass oscillations yields a finite Berry phase of ,0.42p, suggesting the Dirac nature of the surface states. Our results demonstrate that Bi2Se2Te can serve as a suitable topological insulator candidate for achieving intrinsic quantum transport of surface Dirac fermions.

42 ENGINEERING↗

The Nanocrystalline SnO 2 –TiO 2 System‒Part II: Surface Energies and Thermodynamic Stability

The thermodynamic stability of nanocrystalline SnO 2 –TiO 2 solid solutions was studied experimentally. Microcalorimetry of water adsorption revealed a systematic decrease in the surface energy with increasing Ti 4+ content in the SnO 2 ‐rich compositions, consistent with previous reports of Ti 4+ segregation on the surface. The surface energy change was accompanied by an increase in the magnitude of the heat of water adsorption, also indicating a modification of the SnO 2 surface by Ti 4+ . Supporting the water adsorption data, calculations using high‐temperature oxide melt solution calorimetry data also suggest a decrease in the interface energies. A thermodynamic analysis showed that the observed surface energy decrease is responsible for an increase in the stability of solid solutions in the nanophase regime. Although a miscibility gap is expected in this system from bulk phase diagrams, the surface energy contribution modifies the bulk trend and promotes extensive solid solutions when the surface area is above a critical value dependent on the surface energy and the bulk enthalpy of mixing.

Miagava, Joice↗

Reference Site Conditions for Floating Wind Arrays in the United States

Floating offshore wind farm design is highly site-specific, requiring detailed information about the specific conditions of a project area for realistic design studies. Unfortunately, publicly available site condition data for potential floating offshore wind project sites in the United States is scarce. To support U.S. offshore wind research, we developed reference site condition datasets, including metocean and seabed information, for four potential floating wind project areas in the U.S.: Humboldt Bay, Morro Bay, the Gulf of Maine, and the Gulf of Mexico. These datasets were compiled using publicly available data. Our metocean analysis, covering wind, waves, and surface currents, utilized measurement data from 2000 to 2020. Sources included the National Renewable Energy Laboratory’s National Offshore Wind Dataset for wind data, National Data Buoy Center buoys for wave data, and the High Frequency Radar Network for surface currents. These data were integrated into hourly time series used to compute extreme return periods up to 500 years, monthly statistics, and joint probability clusters for fatigue analysis. Soil conditions were evaluated using the usSEABED database and bathymetry grids were interpolated from the NCEI Digital Elevation Model Global Mosaic. In addition to providing curated reference site condition datasets for four U.S. areas, our assessment highlights the need for more publicly available metocean and soil condition data.

17 WIND ENERGY↗

Effect of Air Oxidation on Pore Structure Development and Mechanical Properties of Nuclear Graphite

This document reports on continuation of R&D activities at ORNL directed at investigating the effect of air oxidation of nuclear graphite on development and structure of porosity in the oxidized layer, and on the effect on mechanical properties of oxidized graphite. The material investigated was nuclear-grade graphite (purified PCEA graphite, from GrafTech International). Based on conclusions of previous work (ORNL/TM-2009/192), the method of analysis of the porosity in the oxidized layer based on optical microscopy coupled with automated image analysis was further improved and standardized. In addition, characterization of oxidized specimens by optical microscopy was complemented with measurements of mechanical properties (compressive strength) on a statistically significant number of specimens. A series of cylindrical shape specimens were machined and oxidized in air at two temperatures (600 and 700 o C) and at three levels of burn-off at each temperature (5-6 %; 10-12 % and 15-17%). The procedure used for specimen preparation and oxidation, and the oxidation equipment, were those recommended in ASTM D-7542-09. However, in order to comply with the aspect ratio requirements for specimens employed in compressive strength measurements (ASTM C-695-91) all specimens were machined with a length to diameter ratio of 2 (i.e. 25.4 mm height vs. 12.7 mm diameter) instead of 25.4 mm length and 25.4 mm diameter recommended by ASTM D-7542-09. After oxidation, mechanical properties (compressive strength) were measured on at least three samples obtained at equal oxidation conditions, while another specimen from the same lot was sectioned, mounted in resin and surface polished for optical microscopy analysis. In the latter procedure, mosaic pictures were collected of a rectangular stripe across the diameter of each specimen. These images were analyzed in order to derive the penetration depth and the pore structure in the oxidized layer as a function of oxidation temperature and weight loss level. Automated image analysis was performed using the commercial software Image Pro Plus. The results led to the conclusion that the depth of the oxidation layer is more dependent on the oxidation temperature than on the level of weight-loss. The penetration depth of the oxidized layer is about 6 mm at 600 o C and about 1.5 mm at 700 o C. Consequently, the 12.5 mm diameter specimens oxidized at 600 o C were completely penetrated by oxidation, while those oxidized at 700 o C had the oxidation layer restricted in a narrower band near the exposed surface. This difference was reflected by mechanical properties. A closer analysis of high magnification images in the oxidized layer revealed that oxidation attacks preferentially the binder phase in graphite, where development of fine new pores was observed. The density of new pores was higher near large pores pre-existing in graphite structure. Acute oxidation at low temperatures (e.g. 600 o C) causes more damage on mechanical strength than high temperature oxidation (700 o C). Although the latter is much faster, the oxidized layer is limited to a narrow zone next to the external surface, so that the core is not visibly affected. In contrast, oxidation at lower temperature, although slower, is more damaging because it penetrates deeply beyond the exposed surface.

36 MATERIALS SCIENCE↗

Synthesis and characterization of nanoapatites organofunctionalized with aminotriphosphonate agents

Organofunctionalized apatite nanoparticles were prepared using a one step process involving dissolution/precipitation of natural phosphate rock and covalent grafting of nitrilotris(methylene)triphosphonate (NTP). The synthesized materials were characterized by Brunauer-Emmett-Teller (BET) surface measurement, thermogravimetry, inductively coupled plasma emission spectroscopy (ICP-ES), elemental analysis, multinuclear solid state cross-polarization/magic angle spinning (CP/MAS) and single-pulse NMR spectroscopy, transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDXA). After grafting BET measurements yielded particle specific surface areas ranging from 88 to 193 m{sup 2} g{sup -1} depending on the grafted phosphonate. The results show that the surfaces of the nanoapatite particles can be covered with functional groups bound through a variable number of R-P-O-Ca bonds to render them organoapatites. - Graphical Abstract: Hydroxyapatite in the form of naturally occurring phosphate rock is converted in the presence of nitrilotris(methylene)triphosphonate (NTP) to high surface area apatite nanoparticles (dimensions measured by TEM) with NTP-functionalized surfaces. Highlights: Black-Right-Pointing-Pointer Surface functionalized hydroxyapatite nanoparticles are prepared from natural phosphate rock in a one-step process. Black-Right-Pointing-Pointer Covalent grafting of amine phosphonates to the nanoparticle surface is simultaneously accomplished by the presence of the organic molecules in the solution. Black-Right-Pointing-Pointer Mesoporous particles of high surface area are created. Black-Right-Pointing-Pointer Surface coverage is controlled by the concentration of amine phosphonate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling the Effect of Surface Platinum–Tin Alloys on Propane Dehydrogenation on Platinum–Tin Catalysts

Uncertainty analysis, reported experimental literature data, and density functional theory were synthesized to model the effect of surface tin coverage on platinum-based catalysts for nonoxidative propane dehydrogenation to propylene. Here, this study tests four different platinum–tin skin surface models as potential catalytic sites, Pt 3 Sn/Pt(100), PtSn/Pt(100), Pt 3 Sn/Pt(111), and Pt 2 Sn/Pt(211), and compares them to the corresponding pure Pt surface sites using an uncertainty analysis methodology that uses BEEF-vdW with its ensembles (BMwE) to generate the uncertainty for the energies of the intermediates and transition states. One experimental data set with two experimental observations, selectivity to propylene and turnover frequency of propylene, was used as a calibration data set to evaluate the impact of the experimental data on informing the models. This study finds that the prior model for Pt 3 Sn/Pt(100) is the most active and Pt 2 Sn/Pt(211) is the most selective toward propylene. Active sites on the (100) facet have the highest probability of being responsible for C 1 and C 2 product formations (C–C bond cleavage). Increasing the Sn coverage on the (100) surface facet to a PtSn/Pt(100) active site leads to a significantly reduced rate and might explain the experimentally observed higher selectivity of Sn-doped catalysts relative to pure Pt catalysts. Next, this study finds that for all surfaces, except PtSn/Pt(100), the rate-controlling steps are the initial dehydrogenation steps alongside some partially rate-controlling second dehydrogenation steps. For PtSn/Pt(100), only the initial terminal dehydrogenation step to CH 3 CH 2 CH 2 * and second dehydrogenation steps are rate-controlling. Next, the calibrated models for all surfaces were found to be selective toward propylene production and model the reported turnover frequency successfully. Nevertheless, Pt 2 Sn/Pt(211) emerges as the active site with some (minor) evidence as the main active site based on Jeffreys’ scale interpretation of Bayes factors. This observation agrees with prior studies that also found step sites to be most likely the most relevant active sites for pure Pt catalysts. Overall, the results indicate that tin, in addition to affecting the binding strength of the adsorbed species, prevents deeper dehydrogenation (reducing coking) and cracking reactions through increasing activation barriers for unwanted side reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

FLiNaK Compatability Studies with Inconel 600 and Silicon Carbide

A small liquid fluoride salt test apparatus has been constructed and testing conducted to examine the compatibility of SiC, Inconel 600, and a spiral wound gasket material in FLiNaK salt. These tests were conducted to test materials and sealing systems that would be used in a FLiNaK salt test loop. Three months of testing at 700oC was used to assure that these materials and seals would be acceptable operating under expected test loop conditions. The SiC specimens showed little or no change over the test period while the spiral wound gasket material showed no degradation, except for the possibility of salt seeping into the outermost spirals of the gasket. The Inconel 600 specimens showed regions of voiding which penetrated the specimen surface to about 250 m in depth. Analysis indicated that the salt had leached chrome from the Inconel surface as was expected for this material. Because the test loop will have a limited working lifetime, it was concluded that these materials would be satisfactory for loop construction.

42 ENGINEERING↗

Study of Electrochemical Reactions Using Nanospray Desorption Electrospray Ionization Mass Spectrometry

The combination of electrochemistry (EC) and mass spectrometry (MS) is a powerful analytical tool for studying mechanisms of redox reactions, identification of products and intermediates, and online derivatization/recognition of analytes. This work reports a new coupling interface for EC/MS by employing nanospray desorption electrospray ionization (nano-DESI), a recently developed ambient ionization method. We demonstrate online coupling of nano-DESI-MS with a traditional electrochemical flow cell, in which the electrolyzed solution emanating from the cell is ionized by nano-DESI for MS analysis. Furthermore, we show first coupling of nano-DESI-MS with an interdigitated array (IDA) electrode enabling chemical analysis of electrolyzed samples directly from electrode surfaces. Because of its inherent sensitivity, nano-DESI enables chemical analysis of small volumes and concentrations of sample solution. Specifically, good-quality signal of dopamine and its oxidized form, dopamine ortho-quinone, was obtained using 10 μL of 1 μM solution of dopamine on the IDA. Oxidation of dopamine, reduction of benzodiazepines, and electrochemical derivatization of thiol groups were used to demonstrate the performance of the technique. Our results show the potential of nano-DESI as a novel interface for electrochemical mass spectrometry research.

Ambient ionization↗

MoVN-Cu Coatings for In Situ Tribocatalytic Formation of Carbon-Rich Tribofilms in Low-Viscosity Fuels

Inhibiting the tribological failure of mechanical assemblies which rely on fuels for lubrication is an obstacle to maintaining the lifetime of these systems with low-viscosity and low-lubricity fuels. Here in the present study, a MoVN-Cu nanocomposite coating was tribologically evaluated for durability in high- and low-viscosity fuels as a function of temperature, load, and sliding velocity conditions. The results indicate that the MoVN-Cu coating is effective in decreasing wear and friction relative to an uncoated steel surface. Raman spectroscopy, transmission electron microscopy, and electron-dispersive spectroscopy analysis of the MoVN-Cu worn surfaces confirmed the presence of an amorphous carbon-rich tribofilm which provides easy shearing and low friction during sliding. Further, the characterization of the formed tribofilm revealed the presence of nanoscale copper clusters overlapping with the carbon peak intensities supporting the tribocatalytic origin of the surface protection. The tribological assessment of the MoVN-Cu coating reveals that the coefficient of friction decreased with increasing material wear and initial contact pressure. These findings suggest that MoVN-Cu is a promising protective coating for fuel-lubricated assemblies due to its adaptive ability to replenish lubricious tribofilms from hydrocarbon environments.

36 MATERIALS SCIENCE↗

Designing Pulse Laser Surface Modification of H13 Steel Using Response Surface Method

This paper presents a design of experiment (DOE) for laser surface modification process of AISI H13 tool steel in achieving the maximum hardness and minimum surface roughness at a range of modified layer depth. A Rofin DC-015 diffusion-cooled CO{sub 2} slab laser was used to process AISI H13 tool steel samples. Samples of 10 mm diameter were sectioned to 100 mm length in order to process a predefined circumferential area. The parameters selected for examination were laser peak power, overlap percentage and pulse repetition frequency (PRF). The response surface method with Box-Behnken design approach in Design Expert 7 software was used to design the H13 laser surface modification process. Metallographic study and image analysis were done to measure the modified layer depth. The modified surface roughness was measured using two-dimensional surface profilometer. The correlation of the three laser processing parameters and the modified surface properties was specified by plotting three-dimensional graph. The hardness properties were tested at 981 mN force. From metallographic study, the laser modified surface depth was between 37 {mu}m and 150 {mu}m. The average surface roughness recorded from the 2D profilometry was at a minimum value of 1.8 {mu}m. The maximum hardness achieved was between 728 and 905 HV{sub 0.1}. These findings are significant to modern development of hard coatings for wear resistant applications.

36 MATERIALS SCIENCE↗

Rumpling of LiF(001) surface from fast atom diffraction

Quantum diffraction of fast atoms scattered from the topmost layer of surfaces under grazing angles of incidence can be employed for the analysis of detailed structural properties of insulator surfaces. From comparison of measured and calculated diffraction patterns we deduce the rumpling of the topmost surface layer of LiF(001) (i.e., an inward shift of Li{sup +} ions with respect to F{sup -} ions). The effect of thermal vibrations on the measurement of rumpling is accounted for by ab initio calculations of the mean-square vibrational amplitudes of surface ions. At room temperature this leads to a reduction of the apparent rumpling by 0.008 A. We then obtain a rumpling of (0.05{+-}0.04) A, which improves its accuracy achieved in previous work.

36 MATERIALS SCIENCE↗

Analysis of fluid flow and heat transfer in a rib grit roughened surface solar air heater using CFD

This paper presents the study of fluid flow and heat transfer in a solar air heater by using Computational Fluid Dynamics (CFD) which reduces time and cost. Lower side of collector plate is made rough with metal ribs of circular, square and triangular cross-section, having 60 inclinations to the air flow. The grit rib elements are fixed on the surface in staggered manner to form defined grid. The system and operating parameters studied are: e/D{sub h} = 0.044, p/e = 17.5 and l/s = 1.72, for the Reynolds number range 3600-17,000. To validate CFD results, experimental investigations were carried out in the laboratory. It is found that experimental and CFD analysis results give the good agreement. The optimization of rib geometry and its angle of attack is also done. The square cross-section ribs with 58 angle of attack give maximum heat transfer. The percentage enhancement in the heat transfer for square plate over smooth surface is 30%. (author)

14 SOLAR ENERGY↗

Some insights into formamide formation through gas-phase reactions in the interstellar medium

We study the viability of different gas-phase ion-molecule reactions that could produce precursors of formamide in the interstellar medium. We analyze different reactions between cations containing a nitrogen atom (NH{sub 3}{sup +}, NH{sub 4}{sup +}, NH{sub 3}OH{sup +}, and NH{sub 2}OH{sup +}) and neutral molecules having one carbonyl group (H{sub 2}CO and HCOOH). First, we report a theoretical estimation of the reaction enthalpies for the proposed processes. Second, for more favorable reactions, from a thermodynamic point of view, we perform a theoretical study of the potential energy surface. In particular, the more exothermic processes correspond to the reactions of ionized and protonated hydroxylamine with formaldehyde. In addition, a neutral-neutral reaction has also been considered. The analysis of the potential energy surfaces corresponding to these reactions shows that these processes present a net activation barrier and that they cannot be considered as a source of formamide in space.

79 ASTRONOMY AND ASTROPHYSICS↗